Search NASA⌕ Search

SEARCH · Search NASA

Results for “attack surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Convergence behavior that controls adaptive wind tunnel walls near the test section in the high angle of attack range

The NACA 0012 profile at Mach 0.5 was investigated in a wind tunnel with adaptive walls. It is found that adaptation of the flexible walls is possible in the high angle of attack range on both sides of maximum lift. Oil film photographs of the flow at the profile surface show three dimensional effects in the region of the corners between the profile and the sidewall. It is concluded that pure two dimensional separated flow is not possible.

Ziemann, J.↗
NASA NTRS1983

An experimental heat-transfer investigation of an advanced winged entry vehicle at Mach 10

Heat-transfer measurements have been made at Mach 10 in air on an instrumented 0.006-scale model of an advanced winged entry vehicle. Data were obtained at 83 thermocouple stations which include locations on the lower and upper surface centerlines, spanwise positions along the lower and upper surfaces of the wing, the lower surface of the body flap, and radial locations on the fuselage. Data were obtained for angles of attack ranging from 0 to 45 deg, sideslip angles of + or - 2 deg, Reynolds numbers of 0.5, 1.0 and 2.0 million per foot, and body-flap deflections of 0, 10, and 20 deg. The data generally indicate increased windward heating and decreased leeside heating with increased angle of attack, significantly increased body-flap heating with deflection angle, and minor variations in heating with sideslip, increasing in magnitude with angle of attack. Windward centerline data are shown to be in fair agreement with results of predictions based on an approximate engineering method.

Wurster, K. E.↗
NASA NTRS1986

Calculation of convective heating on proposed aeroassist flight experiment vehicle

Convective heating calculations of a NASA aeroassist flight experiment (AFE) configuration consisting of a blunted, elliptic cone raked off at the base, and fitted with a skirt-type afterbody with a generous corner radius, are presented. The HALIS inviscid flowfield code is used to supply edge properties to an approximate three-dimensional boundary-layer method to calculate the surface heating. Calculations at Mach number 9.86 and approximate Reynolds number of 500,000, for angles of attack from -10 to 10 degrees, are in general good agreement with Langley 31-inch Mach 10 Tunnel experimental data. The results validate the application of the present overall AFE configuration heating pattern heating contours to aeroassist orbital transfer vehicle heating distribution determinations.

Hamilton, H. H., II↗
NASA NTRS1987

On the nonlinear aerodynamic and stability characteristics of a generic chine-forebody slender-wing fighter configuration

An exploratory investigation was conducted of the nonlinear aerodynamic and stability characteristics of a tailless generic fighter configuration featuring a chine-shaped forebody coupled to a slender cropped delta wing in the NASA Langley Research Center's 12-Foot Low-Speed Wind Tunnel. Forebody and wing vortex flow mechanisms were identified through off-body flow visualizations to explain the trends in the longitudinal and lateral-directional characteristics at extreme attitudes (angles of attack and sideslip). The interactions of the vortical motions with centerline and wing-mounted vertical tail surfaces were studied and the flow phenomena were correlated with the configuration forces and moments. Single degree of freedom, free-to-roll tests were used to study the wing rock susceptibility of the generic fighter model. Modifications to the nose region of the chine forebody were examined and fluid mechanisms were established to account for their ineffectiveness in modulating the highly interactive forebody and wing vortex systems.

Erickson, Gary E.↗
NASA NTRS1987

On the nonlinear aerodynamic and stability characteristics of a generic chine-forebody slender-wing fighter configuration

An exploratory investigation was conducted of the nonlinear aerodynamic and stability characteristics of a tailless generic fighter configuration featuring a chine-shaped forebody coupled to a slender cropped delta wing in the NASA Langley Research Center's 12-Foot Low-Speed Wind Tunnel. Forebody and wing vortex flow mechanisms were identified through off-body flow visualizations to explain the trends in the longitudinal and lateral-directional characteristics at extreme attitudes (angles of attack and sideslip). The interactins of the vortical motions with centerline and wing-mounted vertical tail surfaces were studied and the flow phenomena were correlated with the configuration forces and moments. Single degree-of-freedom, free-to-roll tests were used to study the wing rock susceptibility of the generic fighter model. Modifications to the nose region of the chine forebody were examined and fluid mechanisms were established to account for their ineffectiveness in modulating the highly interactive forebody and wing vortex systems.

Erickson, Gary E.↗
NASA NTRS1988

The calculation of flow over iced airfoils

Progress toward the development of a method for predicting the flowfield of an iced airfoil is described and shown to offer the prospect of a priori calculations of the effects of ice accretion and roughness on airfoil performance. The approach is based on interaction of inviscid flow solutions obtained by a panel method and improved upon by a finite-difference boundary-layer method which, operating in an inverse mode, incorporates viscous effects including those associated with separated flows. Results are presented for smooth, rough and iced airfoils as a function of angle of attack. Those for smooth and rough airfoils confirm the accuracy of the method and its applicability to surfaces with roughness similar to that associated with insect deposition and some forms of ice. Two procedures have been developed to deal with large ice accretion and their performance is examined and shown to be appropriate to the engineering requirements.

Cebeci, Tuncer↗
NASA NTRS1988

Effect of large amplitude pitching motions on the unsteady aerodynamic characteristics of flat-plate wings

Large-amplitude unsteady motion effects on the aerodynamic force and stability characteristics of flat-plate wings were investigated in a wind tunnel for the cases of two delta wings with respective leading edge sweeps of 70 and 45 deg, and a rectangular wing whose aspect ratio was equal to that of the 70-deg delta wing. Attention was given to the effects of reduced frequency and mean angle of attack. It is found that lags in vortex burst location and separation/reattachment of flow on the upper surface of the wing produced large overshoots and hysteresis loops in normal force and pitching moment coefficients that were a strong function of mean oscillation angle and reduced frequency.

Brandon, Jay M.↗
NASA NTRS1991

A parametric study of the leading edge attachment line for the F-16XL

A three-dimensional Navier-Stokes code is used to computationally simulate the flow about a modified F-16XL. Transition mechanisms (e.g. attachment line location and crossflow instability) near the swept wing leading edge are analyzed in detail. Flow visualization is used to study the influence of angle-of-attack on the aforementioned transition mechanisms. Validation of the code is accomplished by comparison of numerically generated surface pressures with that obtained by in-flight experiments.

Flores, Jolen↗
NASA NTRS1993

Actuator and aerodynamic modeling for high-angle-of-attack aeroservoelasticity

Accurate prediction of airframe/actuation coupling is required by the imposing demands of modern flight control systems. In particular, for agility enhancement at high angle of attack and low dynamic pressure, structural integration characteristics such as hinge moments, effective actuator stiffness, and airframe/control surface damping can have a significant effect on stability predictions. Actuator responses are customarily represented with low-order transfer functions matched to actuator test data, and control surface stiffness is often modeled as a linear spring. The inclusion of the physical properties of actuation and its installation on the airframe is therefore addressed in this paper using detailed actuator models which consider the physical, electrical, and mechanical elements of actuation. The aeroservoelastic analysis procedure is described in which the actuators are modeled as detailed high-order transfer functions and as approximate low-order transfer functions. The impacts of unsteady aerodynamic modeling on aeroservoelastic stability are also investigated in this paper by varying the order of approximation, or number of aerodynamic lag states, in the analysis. Test data from a thrust-vectoring configuration of an F/A-18 aircraft are compared to predictions to determine the effects on accuracy as a function of modeling complexity.

Brenner, Martin J.↗
NASA NTRS1921

Causes of Cracking of Ignition Cable

The experiments described here show that the cracking at sharp bends, observed in the insulation of internal combustion engine high tension ignition wires after service, is due to a chemical attack upon the rubber by the ozone produced by the electric discharge that takes place at the surface of the cable. This cracking does not occur if the insulating material is not under tension, or if the cable is surrounded by some medium other than air. But it does occur even if the insulation is not subjected to electric stress, provided that the atmosphere near the cable contains ozone. The extent of this cracking varies greatly with the insulating material used. The cracking can be materially reduced by using braided cable and by avoiding sharp bends.

Silsbee, F B↗
NASA NTRS1936

Wind-Tunnel Research Comparing Lateral Control Devices Particularly at High Angles of Attack XIII : Auxiliary Airfoils Used as External Ailerons

This is the thirteenth report on a series of systematic tests comparing lateral control devices with particular reference to their effectiveness at high angles of attack. The present wind tunnel tests were made to determine the most feasible locations for lateral control surfaces mounted externally to a rectangular Clark y wing.

Weick, Fred E↗
NASA NTRS1993

Actuator and aerodynamic modeling for high-angle-of-attack aeroservoelasticity

Accurate prediction of airframe/actuation coupling is required by the imposing demands of modern flight control systems. In particular, for agility enhancement at high angle of attack and low dynamic pressure, structural integration characteristics such as hinge moments, effective actuator stiffness, and airframe/control surface damping can have a significant effect on stability predictions. Actuator responses are customarily represented with low-order transfer functions matched to actuator test data, and control surface stiffness is often modeled as a linear spring. The inclusion of the physical properties of actuation and its installation on the airframe is therefore addressed using detailed actuator models which consider the physical, electrical, and mechanical elements of actuation. The aeroservoelastic analysis procedure is described in which the actuators are modeled as detailed high-order transfer functions and as approximate low-order transfer functions. The impacts of unsteady aerodynamic modeling on aeroservoelastic stability are also investigated by varying the order of approximation, or number of aerodynamic lag states, in the analysis. Test data from a thrust-vectoring configuration of an F/A-l8 aircraft are compared to predictions to determine the effects on accuracy as a function of modeling complexity.

Brenner, Martin J.↗
NASA NTRS1993

Wind-tunnel investigation of aerodynamic efficiency of three planar elliptical wings with curvature of quarter-chord line

Three planar, untwisted wings with the same elliptical chord distribution but with different curvatures of the quarter-chord line were tested in the Langley 8-Foot Transonic Pressure Tunnel (8-ft TPT) and the Langley 7- by 10-Foot High-Speed Tunnel (7 x 10 HST). A fourth wing with a rectangular planform and the same projected area and span was also tested. Force and moment measurements from the 8-ft TPT tests are presented for Mach numbers from 0.3 to 0.5 and angles of attack from -4 degrees to 7 degrees. Sketches of the oil-flow patterns on the upper surfaces of the wings and some force and moment measurements from the 7 x 10 HST tests are presented at a Mach number of 0.5. Increasing the curvature of the quarter-chord line makes the angle of zero lift more negative but has little effect on the drag coefficient at zero lift. The changes in lift-curve slope and in the Oswald efficiency factor with the change in curvature of the quarter-chord line (wingtip location) indicate that the elliptical wing with the unswept quarter-chord line has the lowest lifting efficiency and the elliptical wing with the unswept trailing edge has the highest lifting efficiency; the crescent-shaped planform wing has an efficiency in between.

Mineck, Raymond E.↗
NASA NTRS1995

Performance of an aerodynamic yaw controller mounted on the space shuttle orbiter body flap at Mach 10

A wind-tunnel investigation of the effectiveness of an aerodynamic yaw controller mounted on the lower surface of a shuttle orbiter model body flap was conducted in the Langley 31-Inch Mach 10 Tunnel. The controller consisted of a 60 deg delta fin mounted perpendicular to the body flap lower surface and yawed 30 deg to the free stream direction. The control was tested at angles of attack from 20 deg to 40 deg at zero sideslip for a Reynolds number based on wing mean aerodynamic chord of 0.66 x 10(exp 6). The aerodynamic and control effectiveness characteristics are presented along with an analysis of the effectiveness of the controller in making a bank maneuver for Mach 18 flight conditions. The controller was effective in yaw and produced a favorable rolling moment. The analysis showed that the controller was as effective as the reaction control system in making the bank maneuver. These results warrant further studies of the aerodynamic/aerothermodynamic characteristics of the control concept for application to future transportation vehicles.

Scallion, W. I.↗
NASA NTRS1981

Alleviation of Spin-Entry Tendencies through Localization of Wing-Flow Separation

Studies have been made on several wing leading-edge modifications applicable at present to single-engine light aircraft, which produce stabilizing vortices at stall and beyond. These vortices have the effect of fixing the stall pattern of the wing such that the various portions of the wing upper surface stall nearly symmetrically. The lift coefficient produced is maintained at a high level to angles of attack significantly above the stall angle of the unmodified wing, and the divergence in roll usually is reduced to a controllable level. It is hypothesized that these characteristics will help prevent inadvertent spin entry after a stall. Results are presented from recent large-scale wind-tunnel tests of a typical light aircraft, both with and without the modifications. The data indicate (hot the static stall and poststall characteristics of this aircraft, in a typical landing-approach condition, are noticeably improved when it suitable leading-edge modification is employed; and also that no appreciable aerodynamic penalties are evident in the normal flight envelope.

Feistel, T. W.↗
NASA NTRS1961

Longitudinal Force and Moment Data at Mach Numbers from 0.60 to 1.40 for a Family of Elliptic Cones with Various Semiapex Angles

An investigation has been made to determine the aerodynamic characteristics of four elliptic cones having plan-form semiapex angles ranging from about 9 to 31 deg., and also for one of these cones modified on the upper surface to reduce the base area by about one half. The tests were made for angles of attack from about -2 to +21 deg., at Mach numbers from 0.60 to 1.40, and for a constant Reynolds number of 1.4 million, based on the length of the models. For each model, lift, pitching-moment, and drag coefficients, and lift-drag ratios are presented for the forebody, and axial-force coefficients are presented for the base. Calculated lift and pitching- moment curves for the elliptic cones, and lift-curve slopes for each model at supersonic Mach numbers are shown for comparison with the corresponding experimental values. Lift-drag ratios are also given for the forebody and base combined. These data are presented without discussion.

Stivers, Louis S., Jr.↗
NASA NTRS2002

Atomic Oxygen Protection of Materials in Low Earth Orbit

Spacecraft polymeric materials as well as polymer-matrix carbon-fiber composites can be significantly eroded as a result of exposure to atomic oxygen in low Earth orbit (LEO). Several new materials now exist, as well as modifications to conventionally used materials, that provide much more resistance to atomic oxygen attack than conventional hydrocarbon polymers. Protective coatings have also been developed which are resistant to atomic oxygen attack and provide protection of underlying materials. However, in actual spacecraft applications, the configuration, choice of materials, surface characteristics and functional requirements of quasi-durable materials or protective coatings can have great impact on the resulting performance and durability. Atomic oxygen degradation phenomena occurring on past and existing spacecraft will be presented. Issues and considerations involved in providing atomic oxygen protection for materials used on spacecraft in low Earth orbit will be addressed. Analysis of in-space results to determine the causes of successes and failures of atomic oxygen protective coatings is presented.

Banks, Bruce A.↗
NASA NTRS1960

Static Longitudinal Stability and Control Characteristics At A Mach Number of 1.99 of a Lenticular-Shaped Reentry Vehicle

An investigation has been made in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 1.99 to determine the longitudinal stability and control characteristics of a reentry model consisting of a lenticular-shaped body with two fin configurations (horizontal fins with end plates). Effects of deflecting the larger size fins as pitch-control surfaces were also investigated. The results indicate that the body alone was unstable from an angle of attack of 0 deg to about 55 deg where it became stable and remained so to 90 deg. The addition of fins provided positive longitudinal stability throughout the angle-of-attack range and increased the lift-drag ratio of the configuration. Reducing the horizontal-fin area at the inboard trailing edge of the fin had only a small effect on the aerodynamic characteristics of the vehicle for the condition of no fin deflection. Deflecting the fins, appeared to be an effective means of pitch control and had only a small effect on lift-drag ratio.

Jackson, Charles M., Jr.↗