Search NASA⌕ Search

SEARCH · Search NASA

Results for “beam loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

An investigation of the vibration characteristics of shrouded-bladed-disk rotor stages

Coupled differential equations of motion are given for application to a rotating, pretwisted and heated beam under the effects of thermal stresses and gas bending loads. The circumferential modes of the multi-blade vibration of a bladed-disk rotor stage were studied. A finite element method was developed for the dynamic and static deformation analysis of the blade. The deformations of a bladed disk and a shrouded-bladed disk were studied by introducing a special bladed-disk element and a special shrouded-blade element. Some features of the vibration of part-span-shrouded, bladed-disk rotor stages are discussed. The static deformation, thermal stress and gas bending effects on the blade vibration were presented previously.

Chen, L.-T.↗

Stress intensity factors and COD in an orthotropic strip

The elasticity problem for an orthotropic strip or a beam with an internal or an edge crack under general loading conditions is considered. The numerical results are given for four basic loading conditions, namely, uniform tension, pure bending, three point bending, and concentrated surface shear loading. For the strip with an edge crack additional results regarding the crack opening displacements are obtained by using the plastic strip model. A critical quantity which is tabulated is the maximum compressive stress in the plane of the crack. It is shown that this stress may easily exceed the yield limit in compression and hence may severely limit the range of application of the plasticity results.

Kaya, A. C.↗

Experience on the use of MOSTAB-HFW computer code for horizontal-axis wind turbines

Three topics are covered dealing with the frequencies of a rotating beam, the use of the fundamental mode of a uniform cantilever beam, and the analysis of resonance dwell. Immensely high peak loads were generated by the code for resonance dwell indicating further need for including structural damping and for transient analysis capability. The effect of structural damping, newly incorporated in the code, is described.

Yu, Y. Y.↗

Simultaneous analysis and design for eigenvalue maximization

A simultaneous analysis and design approach to the maximization of buckling or vibration eigenvalues is presented. Both unimodal and bimodal optimum solutions are considered. A discretization of the structure and response is used to obtain sets of nonlinear algebraic equations which are solved numerically. The formulation is applied to the solution of the optimum design of a beam-column supported by an elastic foundation for maximum buckling load. Two cases are considered: the optimum design of the column for a given foundation and the optimum design of the foundation for a given column. Results are compared to published solutions when possible.

Plaut, Raymond H.↗

The Effect of the Angle of Afterbody Keel on the Water Performance of a Flying-Boat Hull Model

NACA model 11-C was tested according to the general method with the angle of afterbody keel set at five different angles from 2-1/2 degrees to 9 degrees, but without changing other features of the hull. The results of the tests are expressed in curves of test data and of non-dimensional coefficients. At the depth of step used in the tests, 3.3 percent beam, the smaller angles of afterbody keel give greater load-resistance ratios at the hump speed and smaller at high speed than the larger angles of afterbody keel. Comparisons are made of the load-resistance ratios at several other points in the speed range. The effect of variation of the angle of afterbody keel upon the take-off performance of a hypothetical flying boat of 15,000 pounds gross weight having a hull of model 11-C lines is calculated, and the calculations show that the craft with the largest of the angles of afterbody keel tested, 9 degrees, takes off in the least time and distance.

Allison, John M.↗

Comparison of Theoretical Stresses and Deflections of Multicell Wings with Experimental Results Obtained from Plastic Models

The experimental deflections and stresses of six plastic multicell-wing models of unswept, delta, and swept plan form are presented and compared with previously published theoretical results obtained by the electrical analog method. The comparisons indicate that the theory is reliable except for the evaluation of stresses in the vicinity of the leading edge of delta wings and the leading and trailing edges of swept wings. The stresses in these regions are questionable, apparently because of simplifications employed in idealizing the actual structure for theoretical purposes and because of local effects of concentrated loads.

LOADS AND STRESSES, STRUCTURAL - TORSION↗

Validation of a Deterministic Vibroacoustic Response Prediction Model

This report documents the recently completed effort involving validation of a deterministic theory for the random vibration problem of predicting the response of launch pad structures in the low-frequency range (0 to 50 hertz). Use of the Statistical Energy Analysis (SEA) methods is not suitable in this range. Measurements of launch-induced acoustic loads and subsequent structural response were made on a cantilever beam structure placed in close proximity (200 feet) to the launch pad. Innovative ways of characterizing random, nonstationary, non-Gaussian acoustics are used for the development of a structure's excitation model. Extremely good correlation was obtained between analytically computed responses and those measured on the cantilever beam. Additional tests are recommended to bound the problem to account for variations in launch trajectory and inclination.

Caimi, Raoul E.↗

Fracture Mechanics Analysis of Stitched Stiffener-Skin Debonding

An analysis based on plate finite elements and the virtual crack closure technique has been implemented to study the effect of stitching on mode I and mode II strain energy release rates for debond configurations. The stitches were modeled as discrete nonlinear fastener elements with a compliance determined by experiment. The axial and shear behavior of the stitches was considered, however, the two compliances and failure loads were assumed to be independent. Both a double cantilever beam (mode I) and a mixed mode skin-stiffener debond configuration were studied. In the double cantilever beam configurations, G(sub I) began to decrease once the debond had grown beyond the first row of stitches and was reduced to zero for long debonds. In the mixed-mode skin-stiffener configurations, G(sub I) showed a similar behavior as in the double cantilever beam configurations, however, G(sub u), continued to increase with increasing debond length.

Glaessgen, E. H.↗

TPSAS-NF1676L-32920-DND

In June 2019, a full-scale crash test of a Fokker F28 Fellowship aircraft will be conducted at NASA Langley Research Center?s Landing and Impact Research (LandIR) Facility. The F28 is a high-performance twin-turbo fan narrow-body aircraft with seating in a 3+2 configuration. The MK4000 variant, used in this test, is capable of carrying up to 85 passengers on medium range routes. The F28 was first type certified by the Federal Aviation Administration (FAA) in 1969 and now the majority of the F28 fleet has retired from service in the United States. In 2016, the FAA and NASA Langley Research Center (LaRC) signed an interagency agreement for conducting a research program to obtain test data that will support the development of airframe level crash requirements for transport category airplanes [1]. The objectives of the full-scale crash test can be divided into six categories: (1) To compare and contrast responses in identical aircraft undergoing vertical only to combined vertical and horizontal loading conditions, (2) To examine the effects of horizontal loading on aircraft structure during a crash event, (3) To generate data for the use in calibration of computer modelling efforts, (4) To generate data from onboard Anthropomorphic Test Devices (ATDs) for the evaluation of injury, (5) To obtain data from experimental seats, and (6) To obtain data from new and novel ATD designs including Warrior Injury Assessment MANikin (WIAMan) [2], Test device for Human Occupant Response (THOR), and other newly developed child ATDs. The focus of this presentation will be to document finite element model development of the full-scale F28 aircraft and to present preliminary test-analysis predictions. NASA obtained the full-scale F28 aircraft, plus three fuselage sections and two sets of wings with funding through the NASA Aviation Safety Program in 1998. In addition to the hardware, NASA purchased a full NASTRAN model of the airframe that had been developed by the Dutch manufacturer, Fokker. Beginning in 2016, the NASTRAN model was converted to LS-DYNA? [4, 5] format and modified by combining parts, adding missing parts of internal structure, and including ballast for loading weights, etc. It contains: 89,223 nodes; 24,065 beam elements; 55,404 shell elements; 29,044 solid elements; 740 parts; 80 material definitions; and, 46 Constrained Nodal Rigid Bodies (CNRBs). The aircraft model will be executed in LSDYNA to simulate the test article impact onto a 2-ft.-high bed of soil under combined velocity conditions of 70-ft/s forward and 30-ft/s vertical velocity. Pre-test simulation predictions will be generated and correlated with test data.

Karen E Jackson↗

Dielectric wakefield accelerator to drive to the future FEL light sourcei.

X-ray free-electron lasers (FELs) are expensive instruments and the accelerator holds the largest portion of the cost of the entire facility. Using a high-energy gain dielectric wake-field accelerator (DWA) instead of the conventional accelerator may facilitate reduction of the facility size and significant cost saving. We show that a collinear dielectric wake-field accelerator can, in principle, accelerate low charge and high peak current electron bunches to a few GeV energy with up to 100 kHz bunch repetition rate. Several such accelerators can share the same tunnel and same CW superconducting linac (operating with a few MHz bunch repetition rate) whose sole purpose is feeding the DWAs with wake producing low energy, high charge electron bunches with a desirable periodicity. Then, ten or more x-ray FELs can operate independently, each using its own linac. In this paper, we present an initial case study of a single stage 850 GHz DWA based on a quartz tube with a {approx}100MV/m loaded gradient sufficient to accelerate a 50 pC main electron beam to 2.4 GeV at a 100 kHz bunch repetition rate in just under 30 meters.

36 MATERIALS SCIENCE↗

Status of High Power Tests of Normal Conducting Single-Cell Standing Wave Structures

Our experiments are directed toward the understanding of the physics of rf breakdown in systems that can be used to accelerate electron beams at {approx}11.4 GHz. The structure geometries have apertures, stored energy per cell, and rf pulse duration close to that of the NLC or CLIC. The breakdown rate is the main parameter that we use to compare rf breakdown behavior for different structures at a given set of rf pulse parameters (pulse shape and peak power) at 60 Hz repetition rate. In our experiments, the typical range of the breakdown rate is from one per few hours to {approx}100 per hour. To date we have tested 29 structures. We consistently found that after the initial conditioning, the behavior of the breakdown rate is reproducible for structures of the same geometry and material, and the breakdown rate dependence on peak magnetic fields is stronger than on peak surface electric fields for structures of different geometries. Below we report the main results from tests of seven structures made from hard copper, soft copper alloys and hard-copper alloys. Additional details on these and other structures will be discussed in future publications.

36 MATERIALS SCIENCE↗

Overview of the High Performance Antiproton (HiPAT) Experiment

The annihilation of matter with antimatter represents the highest energy density of any known reaction, producing 10(exp 8) MJ/g, approximately 10 orders of magnitude more energy per unit mass than chemical based combustion. To take the first step towards using this energy for propulsion applications the NASA MSFC Propulsion Research Center (PRC) has initiated a research activity examining the storage of low energy antiprotons. Storage was identified as a key enabling technology since it builds the experience base necessary to understand the handling of antiprotons for virtually all utilization and high-density storage concepts. To address this need, a device referred to as the High Performance Antiproton Trap (HiPAT) is under development at the NASA MSFC PRC. The HiPAT is an electromagnetic system (Penning-Malmberg design) consisting of a 4 Tesla superconductor, a high voltage confinement electrode system (operation up to 20 KV), and an ultra high vacuum test section (operating in the 10(exp -12) torr range). The system was designed to be portable with an ultimate goal of maintaining 10(exp 12) charged particles with a half-life of 18 days. Currently, this system is being experimentally evaluated using normal matter ions which are cheap to produce and relatively easy to handle. These normal ions provide a good indication of overall trap behavior, with the exception of assessing annihilation losses. The ions are produced external to HiPAT using two hydrogen ion sources, with adjustable beam energy and current. Ion are transported in a beam line and controlled through the use of electrostatic optics. These optics serve to both focus and gate the incoming ions, providing microsecond-timed pulses that are dynamically captured by cycling the HiPAT electric containment field like a 'trap door'. The layout of this system more closely simulates the operations expected at an actual antiproton production facility where 'packets' of antiprotons with pulse widths measured in 100's of nanoseconds could be provided. Initial dynamic capture experiments have been performed with both trap and ton source system functioning at approximately 10% of maximum levels, minimizing the potential for extraneous effects. Dynamic trapping techniques demonstrated the successful capture of millions of hydrogen ions with good agreement with the predicted loading based on the timing sequence, trap electric field, and ion beam current. These techniques will be expanded to examine multiple shot capture or 'stacking' to increase the total number of ions stored within HiPAT.

Martin, James J.↗

Rate effects on delamiantion fracture toughness of a toughened graphite/epoxy

The objective of this study was to determine the effects of loading rate on interlaminar fracture toughness of T300/F-185 graphite/epoxy composite, having an elastomer-modified epoxy resin matrix. Mode I interlaminar fracture was investigated by means of uniform width and width-tapered double cantilever beam (DCB) specimens. Hinged tabs were used to insure unrestrained rotation at the free ends. Specimens were loaded at quasi-static deflection rates of up to 8.5 mm/s corresponding to crack extension rates of up to 21 mm/s. Crack extension was monitored by means of strain gages mounted on the surface of the specimen. Continuous records were obtained of load, deflection, and crack extension for determination of the strain energy release rate. The latter was calculated by means of the area method and beam analysis method, and expressed as a power law of the crack extension velocity. Results indicate that the strain energy release rate decreases with crack velocity by over 20 percent over three decades of crack velocity.

Daniel, Isaac M.↗

SIMULATION STUDIES OF A PROTOTYPE STRIPLINE KICKER FOR THE APS-MBA UPGRADE

A prototype dual-blade stripline kicker for the APS multi-bend achromat (MBA) upgrade has been designed and developed. It was optimized with 3D CST Microwave Studio. The high voltage (HV) feedthrough and air-side connector were designed and optimized. Electromagnetic fields along the beam path, the deflecting angle, the high electric fields and their locations were calculated with 15kV differential pulse voltage applied to the kicker blades through the feedthroughs. Beam impedance and the power dissipation on different parts of the kicker and external loads were studied for a 48-bunch fill pattern. Our results show that the prototype kicker with its HV feedthroughs meets the specified requirements. The results of TDR (time-domain reflectometer) test, high voltage pulse test and beam test of the prototype kicker assembly agreed with the simulations.

APS MBA UPGRADE↗

Design, construction and evaluation of a 12.045 GHz, 2.0 kW-cw permanent-magnet focused klystron amplifier

An analytical and experimental program to demonstrate the technical feasibility of a lightweight, high-efficiency, 1-2 kW cw, permanent magnet focused klystron operating at 12.0 GHz was described. The design is based on use of a samarium-cobalt permanent magnet for focusing of the electron beam and choice of the most optimum parameters for maximum efficiency. A filter-loaded output circuit is used for the required bandwidth. The design incorporates a collector which is demountable from the tube to facilitate multistage depressed collector experiments, permitting replacement with a NASA-designed axisymmetric, electrostatic collector for linear beam microwave tubes. A further requirement is that the focusing field between the last interaction gap and the collector decay in a prescribed manner referred to as adiabatic expansion.

Nishida, J. M.↗

Resistive Wall Heating of the Undulator in High Repetition Rate

In next generation high repetition rate FELs, beam energy loss due to resistive wall wakefields will produce significant amount of heat. The heat load for a superconducting undulator (operating at low temperature), must be removed and will be expensive to remove. In this paper, we study this effect in an undulator proposed for a Next Generation Light Source (NGLS) at LBNL. We benchmark our calculations with measurements at the LCLS and carry out detailed parameter studies using beam from a start-to-end simulation. Our preliminarym results suggest that the heat load in the undulator is about 2 W/m or lower with an aperture size of 6 mm for nominal NGLS preliminary design parameters.

43 PARTICLE ACCELERATORS↗

Deflections of beam columns on multiple supports

Lateral deflections of beam columns on multiple equally spaced supports are calculated using the STAGS nonlinear structural analysis computer program. Three lateral loadings are considered, uniform, linear, and uniform over only the center bay. Two types of boundary conditions are considered at the end supports, clamped, and simple support. The effect of an initial sinusoidal imperfection are considered. Deflections in the center and end bays of the beam columns are presented as a function of applied axial compressive load. As the number of bays becomes large, the effect of boundary conditions on the deflections in the center bays diminishes. For cases involving a uniform or linearly varying load, imperfections can have a much larger effect on deflections in the center bays than can lateral pressure.

Stroud, W. J.↗

LBNF 1.2 MW TARGET: CONCEPTUAL DESIGN & FABRICATION

Fermilab’s Long-Baseline Neutrino Facility (LBNF) will utilize a modified design based on the NuMI low energy target that is reconfigured to accommodate beam operation at 1.2 MW. Achieving this power with a graphite target material and ancillary systems originally rated for 400 kW requires several design changes and R&D efforts related to material bonding and electrical isolation. Target cooling, structural design, and fabrication techniques must address higher stresses and heat loads that will be present during 1.2 MW operation, as the assembly will be subject to cyclic loads and thermal expansion. Mitigations must be balanced against compromises in neutrino yield. Beam monitoring and subsystem instrumentation will be updated and added to ensure confidence in target positioning and monitoring. Remote connection to the target hall support structure must provide for the eventual upgrade to a 2.4 MW target design, without producing excessive radioactive waste or unreasonable exposure to technicians during reconfiguration. Current designs and assembly layouts will be presented, in addition to current findings on processes and possibilities for prototype and final assembly fabrication.

43 PARTICLE ACCELERATORS↗