Search NASA⌕ Search

SEARCH · Search NASA

Results for “buffer layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Novel Biomedical Devices Utilizing Light-Emitting Nanostructures

As part of the NASA project, we are investigating the formation, properties, and performance of QD heterostructures, to be incorporated into a novel biomedical device for detecting bacteria and/or viruses in fluids on board space vehicles. We are presently synthesizing the epitaxial quantum dot structures using molecular beam epitaxy. We recently developed a method for controlling the arrangement of QDs, based upon a combination of buffer layer growth and controlled annealing sequences. This method is promising for producing arrangements of QDs with a locally well-controlled distribution of sizes. In the future, we plan to explore selective pre-patterning of the starting surface using focused ion-beam nanopatterning, which will enable us to precisely tune the compositions, sizes, and placement of the QDs, in order laterally tune the emission and detection wavelengths of QD based devices.

Goldman, Rachel S.↗

High-Performance SiC/SiC Ceramic Composite Systems Developed for 1315 C (2400 F) Engine Components

As structural materials for hot-section components in advanced aerospace and land-based gas turbine engines, silicon carbide (SiC) ceramic matrix composites reinforced by high performance SiC fibers offer a variety of performance advantages over current bill-of-materials, such as nickel-based superalloys. These advantages are based on the SiC/SiC composites displaying higher temperature capability for a given structural load, lower density (approximately 30- to 50-percent metal density), and lower thermal expansion. These properties should, in turn, result in many important engine benefits, such as reduced component cooling air requirements, simpler component design, reduced support structure weight, improved fuel efficiency, reduced emissions, higher blade frequencies, reduced blade clearances, and higher thrust. Under the NASA Ultra-Efficient Engine Technology (UEET) Project, much progress has been made at the NASA Glenn Research Center in identifying and optimizing two highperformance SiC/SiC composite systems. The table compares typical properties of oxide/oxide panels and SiC/SiC panels formed by the random stacking of balanced 0 degrees/90 degrees fabric pieces reinforced by the indicated fiber types. The Glenn SiC/SiC systems A and B (shaded area of the table) were reinforced by the Sylramic-iBN SiC fiber, which was produced at Glenn by thermal treatment of the commercial Sylramic SiC fiber (Dow Corning, Midland, MI; ref. 2). The treatment process (1) removes boron from the Sylramic fiber, thereby improving fiber creep, rupture, and oxidation resistance and (2) allows the boron to react with nitrogen to form a thin in situ grown BN coating on the fiber surface, thereby providing an oxidation-resistant buffer layer between contacting fibers in the fabric and the final composite. The fabric stacks for all SiC/SiC panels were provided to GE Power Systems Composites for chemical vapor infiltration of Glenn designed BN fiber coatings and conventional SiC matrices. Composite panels with system B were heat treated at Glenn, and the pores that remained open were filled by silicon melt infiltration (MI). Panels with system A and the other SiC/SiC systems were not heat treated, and remaining open pores in these systems were filled with SiC slurry and silicon MI.

DiCarlo, James A.↗

A Chemical and Structural Study of the AlN-Si Interface

The growth of low defect density heteroepitaxial AlN has great implications for optoelectronic and high power devices since the AlN can be used either as device material or as a buffer layer for the overgrowth of other group-III nitrides. In this work, the results of transmission electron microscopy (TEM) involving both high resolution imaging and electron energy loss spectroscopy (EELS) of AlN/Si layers is reported and the relationship between Si-Al-N interactions and the misorientation of AlN nuclei is elucidated.

epitaxial optoelectronic silicon gallium nitride↗

Low-Noise Large-Area Photoreceivers with Low Capacitance Photodiodes

A quad photoreceiver includes a low capacitance quad InGaAs p-i-n photodiode structure formed on an InP (100) substrate. The photodiode includes a substrate providing a buffer layer having a metal contact on its bottom portion serving as a common cathode for receiving a bias voltage, and successive layers deposited on its top portion, the first layer being drift layer, the second being an absorption layer, the third being a cap layer divided into four quarter pie shaped sections spaced apart, with metal contacts being deposited on outermost top portions of each section to provide output terminals, the top portions being active regions for detecting light. Four transimpedance amplifiers have input terminals electrically connected to individual output terminals of each p-i-n photodiode.

Joshi, Abhay M.↗

Method of junction formation for CIGS photovoltaic devices

Sulfur is used to improve the performance of CIGS devices prepared by the evaporation of a single source ZIS type compound to form a buffer layer on the CIGS. The sulfur may be evaporated, or contained in the ZIS type material, or both. Vacuum evaporation apparatus of many types useful in the practice of the invention are known in the art. Other methods of delivery, such as sputtering, or application of a thiourea solution, may be substituted for evaporation.

Delahoy, Alan E↗

Muscle-driven nanogenerators

In a method of generating electricity, a plurality of living cells are grown on an array of piezoelectric nanowires so that the cells engage the piezoelectric nanowires. Induced static potentials are extracted from at least one of the piezoelectric nanowires when at least one of the cells deforms the at least one of the piezoelectric nanowires. A cell-driven electrical generator that includes a substrate and a plurality of spaced-apart piezoelectric nanowires disposed on the substrate. A plurality of spaced-apart conductive electrodes interact with the plurality of piezoelectric nanowires. A biological buffer layer that is configured to promote growth of cells is disposed on the substrate so that cells placed on the substrate will grow and engage the piezoelectric nanowires.

30 DIRECT ENERGY CONVERSION↗

HIGH-TEMPERATURE SAFETY TESTING OF IRRADIATED AGR-1 TRISO FUEL

High-Temperature Safety Testing of Irradiated AGR-1 TRISO Fuel John D. Stempien, Paul A. Demkowicz, Edward L. Reber, and Cad L. Christensen Idaho National Laboratory, P.O. Box 1625 Idaho Falls, ID 83415, USA Corresponding Author: john.stempien@inl.gov, +1-208-526-8410 Two new safety tests of irradiated tristructural isotropic (TRISO) coated particle fuel have been completed in the Fuel Accident Condition Simulator (FACS) furnace at the Idaho National Laboratory (INL). In the first test, three fuel compacts from the first Advanced Gas Reactor irradiation experiment (AGR-1) were simultaneously heated in the FACS furnace. Prior to safety testing, each compact was irradiated in the Advanced Test Reactor to a burnup of approximately 15 % fissions per initial metal atom (FIMA), a fast fluence of 3×1025 n/m2 (E > 0.18 MeV), and a time-average volume-average (TAVA) irradiation temperature of about 1020 °C. In order to simulate a core-conduction cool-down event, a temperature-versus-time profile having a peak temperature of 1700 °C was programmed into the FACS furnace controllers. Gaseous fission products (i.e., Kr-85) were carried to the Fission Gas Monitoring System (FGMS) by a helium sweep gas and captured in cold traps featuring online gamma counting. By the end of the test, a total of 3.9% of an average particle’s inventory of Kr-85 was detected in the FGMS traps. Such a low Kr-85 activity indicates that no TRISO failures (failure of all three TRISO layers) occurred during the test. If released from the compacts, condensable fission products (e.g., Ag-110m, Cs-134, Cs-137, Eu-154, Eu-155, and Sr-90) were collected on condensation plates fitted to the end of the cold finger in the FACS furnace. These condensation plates were then analyzed for fission products. In the second test, five loose UCO fuel kernels, obtained from deconsolidated particles from an irradiated AGR-1 compact, were heated in the FACS furnace to a peak temperature of 1600 °C. This test had two primary goals. First, the test was intended to assess the retention of fission products in loose kernels without the effects of the other TRISO layers (buffer, IPyC, SiC, and OPyC) or the graphitic matrix material comprising the compact. Second, this test served as an evaluation of the FACS fission product condensation plate collection efficiency.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thallium bromide (TIBr) semiconductors and devices with extended life apparatus, methods, and system

Various technologies pertaining to formation or treatment of a thallium bromide crystal to improve the operable lifespan of a device that incorporates the thallium bromide crystal are described herein. In exemplary embodiments, treatments including focused ion beam implantation, selective material removal, and buffer layer application are performed on a thallium bromide crystal to inhibit motion of dislocations toward a region at which an electrical contact is desirably installed. In other exemplary embodiments, a thallium bromide crystal is doped with impurities during formation that inhibit the motion of dislocations in the crystal. In still other exemplary embodiments, a thallium bromide crystal is formed by way of processes that inhibit dislocation formation during crystal growth or eliminate dislocations in an existing thallium bromide mass.

36 MATERIALS SCIENCE↗

Reel-to-reel exfoliation and processing of second generation superconductors

The substrate and buffer layers, of either one-sided or two-sided superconducting tape, are separated from the YCBO layer(s) of the tape by a combined action of radiative or inductive heat and mechanical force via a reel-to-reel manufacturing process. The exfoliation process may also utilize an air blade(s) to facilitate the separation of the layers of the tape.

Solovyov, Vyacheslav↗

Microstructural and Micro-Chemical Evolutions in the Irradiated UCO Fuel Kernels of AGR-1 and AGR-2 TRISO Fuel Particles

AGR-1 and AGR-2 TRISO fuel particles were fabricated with slightly different fuel kernel chemical compositions, modified fabrication processes, different fuel kernel diameters, and changed 235U enrichments. To correlate those differences with the fuel kernel responses to neutron irradiations in terms of irradiated fuel microstructure, fission products chemical and physical states, and fission gas bubble evolutions, extensive microstructural and analytical characterizations were conducted. The studies used a state of art transmission electron microscopy (TEM) equipped with Energy-dispersive X-ray spectroscopy (EDS) of four silicon solid-state detectors which have super sensitivity and fast speed. The TEM specimens were prepared from selected AGR-1 and AGR-2 irradiated fuel kernels exposed to safety testing after irradiation. The particles were chosen to represent a representative irradiation conditions with a fuel burnup within the range from 10.8 to 18.6% FIMA, and the time-average volume-average temperatures vary from 1070 to 1287°C. The 235U enrichment was 19.74 wt.% for the AGR1 fuel kernels and 14.03 wt.% for the AGR-2 fuel kernels. The TEM results show that there were significant microstructural reconstructions in the irradiated fuel kernels for both the AGR-1 and AGR-2 fuels. There are four major phases including fuel matrix of UO2 and UC, U2RuC2, and UMoC2 in the irradiated AGR2 fuel kernel. Zr and Nb form solid solution in the UC phase. UMoC2 phase often shows a detectable concentration of Tc. Pd was found to mainly locate in the buffer layer or to be associated with fission gas bubble within the UMoC2 phase. The EDS maps qualitatively show that the rare-earth fission products (Nb, et al.) preferentially reside in the UO2 phase. In contrast, in the irradiated AGR1 fuel kernel, no U2RuC2 or UMoC2 precipitates were positively identified. Instead, there is a high number of rod-shape precipitates enriched with Ru, Tc, Rh, and Pd observed in the fuel kernel center and edge zone. The difference of microstructural and micro-chemical evolutions in irradiated fuel kernels between the AGR-1 and AGR-2 TRISO fuel particle may result from a combined factor of irradiation temperature, fuel geometry and chemical composition. However, the irradiation temperature probably play a more deterministic role. Limited electron energy loss spectroscopy (EELS) characterizations on the AGR2 fuel kernel show that there is nearly no carbon in the UO2 phase while a small fraction of oxygen was detected in the UC/UMoC2 phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Semi-analytical prediction of hydraulic resistance and heat transfer for pipe and channel flows of water at supercritical pressure

Within the Generation IV International Forum the Supercritical Water Reactor is investigated. For its core design and safety analysis the efficient prediction of flow and heat transfer parameters such as the wall-shear stress and the heat-transfer coefficient for pipe and channel flows is needed. For circular pipe flows a numerical model based on the one-dimensional conservation equations of mass, momentum end energy in the radial direction is presented, referred to as a 'semi-analytical' method. An accurate, high-order numerical method is employed to evaluate previously derived analytical solutions of the governing equations. Flow turbulence is modeled using the algebraic approach of Prandtl/van-Karman, including a model for the buffer layer. The influence of wall roughness is taken into account by a new modified numerical damping function of the turbulence model. The thermo-hydraulic properties of water are implemented according to the international standard of 1997. This method has the potential to be used within a sub-channel analysis code and as wall-functions for CFD codes to predict the wall shear stress and the wall temperature. The present study presents a validation of the method with comparison of model results with experiments and multi-dimensional computational (CFD) studies in a wide range of flow parameters. The focus is laid on forced convection flows related to reactor design and near-design conditions. It is found, that the method can accurately predict the wall temperature even under deterioration conditions as they occur in the selected experiments (Yamagata el al. 1972 at 24.5 MPa, Ornatski et al. 1971 at 25.5 and Swenson et al. 1963 at 22.75 MPa). Comparison of the friction coefficient under high heat flux conditions including significant viscosity and density reductions near the wall with various correlations for the hydraulic resistance will be presented; the best agreement is achieve with the correlation of Pioro et al. 2004. It is concluded, that the semi-analytical prediction method is accurate and efficient for forced convection flows even at high heat fluxes. The wall-roughness height is identified as an important model parameter. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Nanocomposite-seeded epitaxial growth of single-domain lithium niobate thin films for surface acoustic wave devices

A method for making LNO film, including the steps of identifying a substrate, identifying a deposition target, placing the substrate and deposition target in a deposition environment, evolving target material into the deposition environment, and depositing evolved target material onto the substrate to yield an LNO film. The deposition environment defines a temperature of between 500 degrees Celsius and 750 degrees Celsius and a pressure of about 10 −6 Torr. A seed or buffer layer may be first deposited onto the substrate, wherein the seed layer is about 30 mole percent gold and about 70 LiNbO 3 .

Wang, Haiyan↗

Production of LEU fully ceramic microencapsulated fuel for irradiation testing

The Advanced Fuels Campaign of the US DOE Fuel Cycle Research/Development program is currently engaged in production of FCM fuel for irradiation testing in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). FCM fuel production is a serial process with 3 major steps namely kernel, TRISO, and compact production. The first step in the kernel process is production of air-dried UO{sub 3} gel spheres with suspended carbon particles. These spheres, roughly 2 mm in size, are then calcined to produce a mixture of UO{sub 2} and carbon. This calcination step may be performed in either argon, hydrogen, or mixtures of these gases. Once the calcination step is complete, temperature is increased (>1400 Celsius degrees) to convert this mixture to UO{sub 2} + UC{sub x}. Once dense oxide-carbide kernels are available, the inert environment is switched to a nitrogen containing one to facilitate carbothermic reduction of kernels and production of UN. Essentially, the oxygen and carbon in the oxide-carbide kernels react with one another to produce CO and are replaced with nitrogen inside the lattice. The TRISO step in fuel production is incorporation of a porous carbon buffer layer, a dense inner pyrolytic carbon layer (IPyC), a SiC layer, and finally and outer pyrolytic carbon layer (OPyC) onto the UN kernels. The coating layer deposition step is carried out inside a graphite furnace using a fluidized bed chemical vapor deposition (CVD) process. In essence, a mixture of reactant and inert gasses flow from the bottom through a bed of particles that are in turn fluidized by the gas stream. The particles undergo CVD and once a different coating layer is to be incorporated, the furnace temperature is adjusted and the reactant gases are changed. The final step in the series of fuel production activities is the consolidation of UN TRISO particles inside the SiC matrix to produce cylindrical pellets. It entails 3 critical areas: SiC powder mixing, over-coating of particles, and high-temperature densification. Optimal execution of the powder mixing step is vital to achieve a fully dense SiC matrix at the end of the process. The SiC matrix is consolidated using a special form of liquid phase sintering (LPS) involving nano-powder feedstock that is designated as the NITE process. The SiC nano-powder slurry is sprayed directly onto the particle surface using a piezoelectric nozzle. Once the over-coated particles are available, final consolidation step at high temperatures (1875 Celsius degrees) is carried out.

36 MATERIALS SCIENCE↗

Thermo mechanical analysis of fully ceramic microencapsulated fuel during in-pile operation

A proposed fuel for improved performance in LWRs (Light Water Reactors) is FCM (fully encapsulated micro-ceramic) fuel concept that involves TRISO (Tri-structural-Isotropic) fuel particles embedded in a NITE (Nano Infiltrated Eutectic) silicon carbide matrix. TRISO fuel particles contain a spherical fuel kernel that will likely range from about 500 to in excess of 800 μm in diameter. The kernel and buffer layer are then typically coated with 3 isotropic layers consisting of a dense inner pyrolytic carbon (IPyC), a silicon carbide (SiC) layer, and an outer layer of dense, pyrolytic carbon (OPyC). These layers are typically around 40 μm thick, but can range from 20 to 60 μm. The TRISO particle packing fraction in the NITE-SiC matrix is expected to be 40-45 vol.%. The release of radioactivity into the coolant is dependent on the integrity of the silicon carbide layer of the TRISO particles and the NITE-SiC matrix. BISON, a code under development by Idaho National Laboratory, has been built on the Multi-physics Object Oriented Simulation Environment (MOOSE). MOOSE is a massively parallel, finite element computational system that uses a Jacobian-free, Newton-Krylov (JFNK) method to solve coupled systems and non-linear partial differential equations. A single particle comparison to fuel performance codes such as PARFUME was conducted and demonstrated that BISON is able to simulate the required physics. FCM pellets embedded with homogenous particles were simulated. It was found that the interior matrix temperature was predicted to be considerably lower than for an equivalent UO{sub 2} pellet. The swelling dependence on temperature created a compressive region around the perimeter of the pellet. However, at fluences above 6.10{sup 25} neutrons/m{sup 2}, the swelling of the pyrolytic carbon might cause significant tensile stresses and possible cracks near the surface of the pellet. This suggests that the pyrolytic carbon swelling may be an important factor in the lifetime of this fuel type.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-irradiation 1600°C Heating Test of AGR-1 UCO Fuel Kernels

Five bare kernels were selected from the U.S. Advanced Gas Reactor (AGR) 1 irradiation experiment Compact 5-3-1 to perform post-irradiation safety tests. The safety test involved heating the kernels in the Fuel Accident Condition Simulator (FACS) furnace in the inert atmosphere to a peak temperature of 1600°C and isothermally holding at this temperature for about 47 hours while collecting fission products released. This test was to assess the retention of fission products in bare kernels without the effects of the other TRISO layers (buffer, IPyC, SiC, and OPyC) or the graphitic matrix material. The bare kernels released nearly 100% of cesium and antimony, while they were able to maintain about 30% of europium, 50% of strontium, and the majority of cerium and ruthenium. In addition, about 48% of the calculated inventory of Kr-85 released during the test, indicating that kernels were capable of retaining a considerable fraction of fission gas K-85 during irradiation.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

YBCO COATED CONDUCTORS

Since the discovery of high-temperature superconductors (HTS) in 1986, both (Bi,Pb)2Sr2Ca2Cu3O10 (BSCCO or 2223 with a critical temperature, Tc of 110 K) and YBa2Cu3O7- (YBCO or 123 with a Tc of 91 K) have emerged as the leading candidate materials for the first generation (1G) and second generation (2G) high temperature superconductor wires or tapes that will carry high critical current density in liquid nitrogen temperatures [1-7]. The crystal structures and detailed fundamental properties of BSCCO and YBCO superconductors have been reviewed by Matsumoto in a separate chapter in this book. The U.S. Department of Energy s target price for the conductor is close to the current copper wire cost of $10-50/kA-meter, i.e. a meter of copper type conductor carrying 1000 A current costs ~ $ 50 [8]. The long-term goal for the DOE, Office of Electricity, Advanced Conductors and Cables program is to achieve HTS wire in 1000 meters long with current carrying capacity of 1000 A/cm [8]. Robust, high-performance HTS wire will certainly revolutionize the electric power grid and various other electric power equipments as well. Sumitomo Electric Power (Japan) has been widely recognized as the world leader in manufacturing the first-generation HTS wires based on BSCCO materials using the Oxide-Powder-In-Tube (OPIT) over-pressure process [9]. Typically, 1G HTS wires carry critical currents, Ic, of over 200 Amperes (A) in piece lengths of one kilometer lengths at the standard 4 mm width and ~ 200 m thickness. However, due to the higher cost of 1G wire, mainly because of the cost of Ag alloy sheath, the researchers shifted their effort towards the development of YBCO (second generation 2G) tapes in the last fifteen years [1-7]. One of the main obstacles to the ability to carry high critical currents in YBCO films has been the phenomenon of weak links, i.e., grain boundaries formed by the misalignment of neighboring YBCO grains are known to form obstacles to current flow [10]. By carefully aligning the grains in YBCO films, low angle boundaries between superconducting YBCO grains allow more current to flow. In fact below a critical misalignment angle of 4 , the critical current density approaches that of YBCO films grown on single crystal substrates [10]. Typically, 2G HTS wires have three components, flexible metal substrate, buffer layers, and REBa2Cu3O7- (REBCO: RE = Rare Earth) superconductor layers [1-7]. Several methods were developed to obtain biaxially textured templates suitable for fabricating high-performance YBCO coated conductors. They are Ion-Beam Assisted Deposition (IBAD), Rolling-Assisted Biaxially Textured Substrates (RABiTS) and Inclined-Substrate Deposition (ISD). Compared to 1G wire, for producing 2G wires using RABiTS or IBAD process, silver is replaced by a low cost nickel alloy, which allows for fabrication of less expensive HTS wires.

36 MATERIALS SCIENCE↗