Search NASA⌕ Search

SEARCH · Search NASA

Results for “electron doping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Electronic and optical properties of Zn-doped β-Ga 2 O 3 Czochralski single crystals

β-Ga 2 O 3 has several soluble deep acceptors that impart insulating behavior. In this study, we investigate Zn doping (0.25at.%) in bulk Czochralski and vertical gradient freeze β-Ga 2 O 3 . Representative crystals were assessed for orientation (electron backscatter diffraction and Raman spectroscopy), purity (glow discharge mass spectrometry and secondary ion mass spectrometry), optical properties (ultraviolet to near infrared absorption), and electrical properties (resistivity and current–voltage). Purity measurements indicate that Zn evaporation is insufficient to inhibit doping of Zn into β-Ga 2 O 3 . Hybrid functional calculations show Zn substitutes nearly equally on tetrahedral and octahedral sites, with less than ~0.1eV preference for the octahedral (Ga II ) site. Furthermore, calculations show that Zn Ga acts as a deep acceptor with trapping levels ~1.3 and ~0.9eV above the valence band for one and two holes, respectively. The solubility and electronic behavior of Zn dopants are consistent with measured concentrations >1×10 18 atoms/cm 3 and electrical measurements that show resistivity 10 11 –10 13 Ωcm, with no p-type conduction.

36 MATERIALS SCIENCE↗

Doping evolution of spin and charge excitations in the Hubbard model

We shed light on how electronic correlations vary across the phase diagram of the cuprate superconductors, examining the doping evolution of spin and charge excitations in the single-band Hubbard model using determinant quantum Monte Carlo (DQMC). In the single-particle response, we observe that the effects of correlations weaken rapidly with doping, such that one may expect the random phase approximation (RPA) to provide an adequate description of the two-particle response. In contrast, when compared to RPA, we find that significant residual correlations in the two-particle excitations persist up to 40% hole and 15% electron doping (the range of dopings achieved in the cuprates). Ultimately, these fundamental differences between the doping evolution of single- and multi-particle renormalizations show that conclusions drawn from single-particle processes cannot necessarily be applied to multi-particle excitations. Eventually, the system smoothly transitions via a momentum-dependent crossover into a weakly correlated metallic state where the spin and charge excitation spectra exhibit similar behavior and where RPA provides an adequate description.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Intrinsic doping limitations in inorganic lead halide perovskites

Inorganic halide perovskites (HP's) of the CsPbX 3 (X = I, Br, Cl) type have reached prominence in photovoltaic solar cell efficiencies, leading to the expectation that they are a new class of semiconductors relative to the traditional ones. Peculiarly, they have shown an asymmetry in their ability to be doped by holes vs. electrons. Indeed, both structural defect-induced doping as well as extrinsic impurity-induced doping strangely often result in HP's in a unipolar doping (dominantly p-type) with low free carriers’ concentration. This raises the question whether such doping limitations presents just a temporary setback due to insufficient optimization of the doping process, or perhaps this represents an intrinsic, physically-mandated bottleneck. Here we study three fundamental Design Principles (DP's) for ideal doping, applying them via density functional doping theory to these HP's, thus identifying the violated DP that explains the doping limitations and asymmetry in these HP's. Here, the target DP are: (i) requires that the thermodynamic transition level between different charge states induced by the dopants must ideally be energetically shallow both for donors (n-type) or acceptors (p-type); DP-(ii) requires that the ‘Fermi level pinning energies’ for electrons E (n) pin and holes E (p) pin (being the limiting value of the Fermi level before a structural defect that compensate the doping forms spontaneously) should ideally be located inside the conduction band for n-type doping and inside the valence band for p-type doping. DP-(iii) requires that the doping-induced shift in equilibrium Fermi energy ΔE (n) F towards the conduction band for n-type doping (shift of ΔE (p) F towards the valence band, for p-type doping) to be sufficiently large. We find that, even though in HP's based on Br and Cl there are numerous shallow level dopants that satisfy DP-(i), in contrast DP-(ii) is satisfied only for holes and DP-(iii) fails for both holes and electrons, being the ultimate bottleneck for the n-type doping in Iodide HP's. This suggests an intrinsic mechanism for doping limitations in this class of semiconductors in terms of recognized physical mechanisms.

36 MATERIALS SCIENCE↗

Effects of rapid thermal annealing on two-dimensional delocalized electronic states of the epitaxial N δ-doped layer in GaAs

We have conducted rapid thermal annealing (RTA) for improving the two-dimensional (2D) arrangement of electronic states in the epitaxial nitrogen (N) δ-doped layer in GaAs. RTA rearranged the N-pair configurations in the GaAs (001) plane and reduced the number of non-radiative recombination centers. Furthermore, a Landau shift, representing the 2D delocalized electronic states in the (001) plane, was observed at around zero magnetic field intensity in the Faraday configuration.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electronic Structure and Linhard Function of Iron-Based Superconductor La{sub 0.5−x}Na{sub 0.5 + x}Fe{sub 2}As{sub 2}

We perform theoretical studies of the iron-based superconductor La{sub 0.5−x}Na{sub 0.5 + x}Fe{sub 2}As{sub 2}. Using density functional calculation with virtual crystal approximation, band structures, density of states, and Fermi surfaces are obtained for different La/Na composition by varying x value. Furthermore, the nesting property is also investigated using the Linhard function. Our main findings are as follows: For undoped (x = 0.0) case, the magnetic and electronic structure share great similarities with extensively studied BaFe{sub 2}As{sub 2}. Upon hole doping (x = 0.3), the Q = (π,π) nesting property are preserved. However, upon electron doping (x = -0.3), the Fermi surfaces undergo a dramastic change into 3D and complex structure. We find this change is attributed to the comprehensive influence of band filling and chemical pressure of La{sup 3+}. We propose the asymmetric change of Fermi surfaces upon doping may in some sense explain the electron-hole asymmetry in phase diagram.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Spontaneous and strong multi-layer graphene n-doping on soda-lime glass and its application in graphene-semiconductor junctions

Scalable and low-cost doping of graphene could improve technologies in a wide range of fields such as microelectronics, optoelectronics, and energy storage. While achieving strong p-doping is relatively straightforward, non-electrostatic approaches to n-dope graphene, such as chemical doping, have yielded electron densities of 9.5 × 10 12 e/cm 2 or below. Furthermore, chemical doping is susceptible to degradation and can adversely affect intrinsic graphene’s properties. Here we demonstrate strong (1.33 × 10 13 e/cm 2 ), robust, and spontaneous graphene n-doping on a soda-lime-glass substrate via surface-transfer doping from Na without any external chemical, high-temperature, or vacuum processes. Remarkably, the n-doping reaches 2.11 × 10 13 e/cm 2 when graphene is transferred onto a p-type copper indium gallium diselenide (CIGS) semiconductor that itself has been deposited onto soda-lime-glass, via surface-transfer doping from Na atoms that diffuse to the CIGS surface. Using this effect, we demonstrate an n-graphene/p-semiconductor Schottky junction with ideality factor of 1.21 and strong photo-response. As a result, the ability to achieve strong and persistent graphene n-doping on low-cost, industry-standard materials paves the way toward an entirely new class of graphene-based devices such as photodetectors, photovoltaics, sensors, batteries, and supercapacitors.

14 SOLAR ENERGY↗

Role of electron carriers on local surface plasmon resonances in doped oxide semiconductor nanocrystals

Optical properties of carrier-dependent local surface plasmons (LSPs) were studied using dopant-controlled In{sub 2}O{sub 3}:Sn nanocrystals (NCs). From a systematic correlation between LSP excitations and electron carriers, electron-impurity scattering contributed towards plasmon damping as one of a factor that is absent in metal NCs. A threshold electron density (n{sub e}) from a damping dominated regime to a quenched damping regime appeared at around 10{sup 20} cm{sup −3}. The validity of Mie theory failed in ITO NCs with high n{sub e} greater than 10{sup 20} cm{sup −3} since the role of electron carriers could enhance LSPs with simultaneous damped plasmonic excitations, which is valuable information for optical applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Sequential Doping of Ladder-Type Conjugated Polymers for Thermally Stable n-Type Organic Conductors

Doping of organic semiconductors is a powerful tool to optimize the performance of various organic (opto)electronic and bioelectronic devices. Despite recent advances, the low thermal stability of the electronic properties of doped polymers still represents a significant obstacle to implementing these materials into practical applications. Hence, the development of conducting doped polymers with excellent long-term stability at elevated temperatures is highly desirable. Here, we report on the sequential doping of the ladder-type polymer poly(benzimidazobenzophenanthroline) (BBL) with a benzimidazole-based dopant (i.e., N-DMBI). By combining electrical, UV–vis/infrared, X-ray diffraction, and electron paramagnetic resonance measurements, we quantitatively characterized the conductivity, Seebeck coefficient, spin density, and microstructure of the sequentially doped polymer films as a function of the thermal annealing temperature. Importantly, we observed that the electrical conductivity of N-DMBI-doped BBL remains unchanged even after 20 h of heating at 190 °C. This finding is remarkable and of particular interest for organic thermoelectrics.

36 MATERIALS SCIENCE↗

Manifestation of light and heavy electrons in the galvanomagnetic characteristics of Te-doped n-Bi{sub 0.88}Sb{sub 0.12} single crystals

The components of resistivity ({rho}{sub ij}), Hall coefficient (R{sub ijk}), and magnetoresistance ({rho}{sub ij,kl}) of n-Bi{sub 0.88}Sb{sub 0.12} single crystals doped with tellurium to 0.01, 0.1, and 0.2 at % have been measured in the temperature range of 77-300 K. It is concluded that light and heavy electrons are involved in transport processes. The energy spacing between the bands of light and heavy electrons is found to be 40 meV, and the ratios of the effective masses and electron mobilities are estimated as m{sub 2}*/m{sub l}* = 3 and b Almost-Equal-To 0.16, respectively.

36 MATERIALS SCIENCE↗

Anomalous effect due to oxygen vacancy accumulation below the electrode in bipolar resistance switching Pt/Nb:SrTiO{sub 3} cells

In conventional semiconductor theory, greater doping decreases the electronic resistance of a semiconductor. For the bipolar resistance switching (BRS) phenomena in oxides, the same doping principle has been used commonly to explain the relationship between the density variation of oxygen vacancies (V{sub o}¨) and the electronic resistance. We find that the V{sub o}¨ density can change at a depth of ∼10 nm below the Pt electrodes in Pt/Nb:SrTiO{sub 3} cells, depending on the resistance state. Using electron energy loss spectroscopy and secondary ion mass spectrometry, we found that greater V{sub o}¨ density underneath the electrode resulted in higher resistance, contrary to the conventional doping principle of semiconductors. To explain this seemingly anomalous experimental behavior, we provide quantitative explanations on the anomalous BRS behavior by simulating the mobile V{sub o}¨ [J. S. Lee et al., Appl. Phys. Lett. 102, 253503 (2013)] near the Schottky barrier interface.

36 MATERIALS SCIENCE↗

FP-LAPW investigation of electronic, magnetic, elastic and thermal properties of Fe-doped zirconium nitride

Full Potential- Linear Augmented Plane Wave (FP-LAPW) method has been employed to study the electronic, magnetic, elastic and thermal properties of Fe-doped Zirconium nitride. In this work, Fe-atoms were doped into the super cell of ZrN in doping concentrations of 12.5%, 25% and 37.5% to replace Zr atoms. Electronic properties such as band structure and DOS were plotted and compared for the doped compounds. Charge density contours were plotted for all the doped compounds. The non-magnetic ZrN doped in different Fe concentrations were found to be ferromagnetic. Magnetic moments have been calculated and compared. Elastic properties have been studied and compared with electronic properties. Appearance of magnetic ordering and its influence with the elastic properties have been reported. Impact of 3d states of Fe in DOS plot on the elastic nature of the compounds has been highlighted. Thermal properties such as Debye temperature and molar heat capacities at low temperature have been determined. Debye temperature is found to decrease with higher doping concentrations. Molar heat capacities are found to increase with higher concentrations of Fe atoms.

36 MATERIALS SCIENCE↗

Review of Carbon Support Coordination Environments for Single Metal Atom Electrocatalysts (SACS)

This topical review focuses on the distinct role of carbon support coordination environment of single-atom catalysts (SACs) for electrocatalysis. The article begins with an overview of atomic coordination configurations in SACs, including a discussion of the advanced characterization techniques and simulation used for understanding the active sites. A summary of key electrocatalysis applications is then provided. These processes are oxygen reduction reaction (ORR), oxygen evolution reaction (OER), hydrogen evolution reaction (HER), nitrogen reduction reaction (NRR), and carbon dioxide reduction reaction (CO 2 RR). The review then shifts to modulation of the metal atom-carbon coordination environments, focusing on nitrogen and other non-metal coordination through modulation at the first coordination shell and modulation in the second and higher coordination shells. Representative case studies are provided, starting with the classic four-nitrogen-coordinated single metal atom (M$-$N 4 ) based SACs. Bimetallic coordination models including homo-paired and hetero-paired active sites are also discussed, being categorized as emerging approaches. The theme of the discussions is the correlation between synthesis methods for selective doping, the carbon structure–electron configuration changes associated with the doping, the analytical techniques used to ascertain these changes, and the resultant electrocatalysis performance. In conclusion, critical unanswered questions as well as promising underexplored research directions are identified.

36 MATERIALS SCIENCE↗

Active Tuning of Optical Constants in the Visible–UV: Praseodymium-Doped Ceria—a Model Mixed Ionic–Electronic Conductor

Mixed ionic-electronic conductors offer chemical and electrical means for active tuning of their optical constants, e.g. with variations in oxygen non-stoichiometry in Pr 0.1 Ce 0.9 O 2-δ , enabling implementation of adaptive thin film optical devices. Here, we demonstrate in-situ chemo-tuning of the extinction coefficient in Pr 0.1 Ce 0.9 O 2-δ at elevated temperatures and provide a tuning model that treats the interdependence of mobile oxygen vacancies and small polarons coupled to variations in optically active praseodymium ions. Further, a new means for electro-tuning of the optical constants of mixed ionic-electronic conductors was demonstrated experimentally and modeled for Pr 0.1 Ce 0.9 O 2-δ thin films deposited on grid-like electrode structures. Modeling of non-steady state optical transmittance modulations in the latter allows for estimation of oxygen vacancy mobility that determines the switching speed of the device. Quenched-in values of nr and k to room temperature become nonvolatile, providing a modulation range in the extinction coefficient of Δk ~0.1 (change of ~800%) and in the refractive index of Δn r ~0.1 (relative to initial n r of ~2.35). Key figures of merit including, transmission optical modulation of ~0.04 per 1 mV nm -1 , switching energy per area of 670 pJ μm -2 and switching times of seconds, were demonstrated, with further improvements possible.

36 MATERIALS SCIENCE↗

Engineering Electronic Band Structure of Indium-doped Cd 1-x Mg x O Alloys for Solar Power Conversion Applications

CdO-based transparent conducting oxide thin films have great potential applications in many optoelectronic devices because of their high mobility, low resistivity, and high transparency over a wide spectral range. However, because of the low band gap of only 2.2 eV, the transparency of this material is limited in the UV spectral range. Alloying of undoped CdO with a larger band gap material such as MgO increases the band gap but tends to degrade electrical conductivity. Recently, it has been demonstrated that In doping of CdO greatly improves the electrical characteristic of this material by increasing both the carrier density and the mobility. In this work, we present a comprehensive study on CdMgO alloys doped with up to 4 % In. Here, we show that the doping with In extends the composition range of conducting films with a composition of up to 40% of Mg and a band gap of 3.5 eV. Our results could open up a new pathway to transparent conducive oxides that could be used as low-resistivity contacts and UV-transparent electrn emitter windows in thin-film photovoltaic technologies.

14 SOLAR ENERGY↗

Strain-Dependent Electronic and Magnetic of Mg-Doped Monolayer of WS{sub 2}

Magnetic properties of Mg-doped WS{sub 2} monolayer under strain are investigated by ab initio methods. Without strain, the Mg-doped WS{sub 2} monolayer is a magnetic nano material and the total magnetic moment is about 1.68 μ{sub B}. We applied strain to Mg-doped WS{sub 2} monolayer from −10 to 10%. The system changes from semiconductor to half-metallic material from 3 to 10% strain. The magnetic moment gets a maximum value of 2.07 μ{sub B} at −3% compressive strain. However, the magnetic moment of system decreases to zero sharply when compressive strain arrived at −5%. The coupling among the 3s states of Mg, 5d states of W, and 3p states of S is responsible for the strong strain effect on the magnetic properties. Our studies predict Mg-doped WS{sub 2} monolayer under strain to be candidates for application in spintronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural and electrical properties of Si- and Ti-doped Cu{sub 2}SnSe{sub 3} bulks

Silicon-doped (Cu{sub 2}(Sn{sub 1−x}Si{sub x})Se{sub 3} and titanium-doped (Cu{sub 2}(Sn{sub 1−x}Ti{sub x})Se{sub 3} at x=0, 0.05, 0.1, 0.15, and 0.2 were prepared at 550 °C for 2 h with soluble sintering aids of volatile Sb{sub 2}S{sub 3} and Te. Defect chemistry was studied by measuring structural and electrical properties of Si-doped and Ti-doped Cu{sub 2}SnSe{sub 3} (CTSe) as a function of dopant concentration. Si-doped CTSe pellets show p-type at x=0 and 0.05 and n-type at x=0.1, 0.15, and 0.2, whereas Ti-doped CTSe pellets show p-type at x=0, 0.05 and 0.1 and n-type at x=0.15 and 0.2. The lowest hole concentration of 3.6×10{sup 17} cm{sup −3} and the highest mobility of 1525 cm{sup 2} V{sup −1} s{sup −1} were obtained for the Si-doped (Cu{sub 2}(Sn{sub 1−x}Si{sub x})Se{sub 3} bulks at x=0.1 (10% Si), while they were 3.1×10{sup 17} cm{sup −3} and 813 cm{sup 2} V{sup −1} s{sup −1} for the Ti-doped CTSe bulks at x=0.15 (15% Ti), as compared to 1.1×10{sup 18} cm{sup −3} and 209 cm{sup 2} V{sup −1} s{sup −1} for undoped one. The explanations based upon antisite defects of Si-to-Sn, Ti-to-Sn, Cu-to-Sn, and Sn-to-Cu for the changes in electrical property were declared. The study in bulk Si-doped and Ti-doped CTSe is based upon defect state and is consistent and supported by the data of electrical property and lattice parameter. - Graphical abstract: Cu{sub 2}SnSe{sub 3} (CTSe) semiconductor is interesting because of its adjustable electrical properties by extrinsic doping. Si and Ti doping in CTSe leads to high carrier mobility above 800 cm{sup 2} V{sup −1} s{sup −1}. - Highlights: • Cu{sub 2}SnSe{sub 3} (CTSe) is an interesting semiconductor because of its adjustable electrical properties. • Cu(In,Ga)Se{sub 2}, on the contrary, is difficult to change its electrical properties. • Si and Ti doping can change p-CTSe to n-CTSe. • The lowest electron concentration in doped CTSe had the highest mobility above 800 cm{sup 2} V{sup −1} s{sup −1}. • The defects of Si-to-Sn, Ti-to-Sn, Cu-to-Sn, and Sn-to-Cu in Si- and Ti-doped CTSe were proposed.

36 MATERIALS SCIENCE↗

Energetic, electronic and optical properties of lanthanide doped TiO{sub 2}: An ab initio LDA+U study

Substitutional energies, thermodynamic charge transition levels and optical properties of lanthanide doped anatase TiO{sub 2} has been investigated using local density approximation with the Hubbard U correction (LDA+U) within the density functional theory formalism. All the lanthanides apart from La introduced impurity states in the host band gap on doping. The calculated substitutional energies indicate that it is possible to dope TiO{sub 2} with lanthanide ions. The optimal doping percentage was predicted to be ~3% and dopant levels resulting from Ce, Nd, Sm, Gd and Tm doping were found to possess negative U characteristics. In addition the calculated thermodynamic transition levels predicted Lu as not having any possible charge transitions within the host band gap. The calculated optical absorption coefficients indicate that lanthanide doping led to optical absorption in the visible regime. - Graphical abstract: Crystal structure of doped Sm doped TiO{sub 2} (RHS). Calculated PDOS and absorption spectra of Sm doped TiO{sub 2}. - Highlights: • Lanthanide doping significantly improved the optical properties of anatase TiO{sub 2}. • Lanthanide doping led to emission in the visible regions of the optical spectrum. • La, Ce, Pm, Sm, Eu, Gd, Tm, Yb and Lu doping gave good photocatalytic properties. • The optimum doping concentration in anatase TiO{sub 2} was found to be 2.78%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of Se substitution on the thermoelectric performance of n-type Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x} skutterudites

Highlights: ► The simple solid state reaction technique was employed to prepare Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x} skutterudites. ► The thermal conductivity decreases gradually with the increasing Se content. ► Doping with moderate Se is an effective way to enhance the thermoelectric performance of Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x}. ► The highest ZT of 1.11 at 800 K is obtained for the Co{sub 4}Sb{sub 11.3}Te{sub 0.58}Se{sub 0.12} sample. -- Abstract: A series of double-substituted Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x} skutterudites have been fabricated by combining the solid state reaction and the spark plasma sintering method, and the effects of Se substitution on the thermoelectric properties are characterized by measurements of the electrical conductivity, the Seebeck coefficient and the thermal conductivity in the temperature range of 300–800 K. Doping Se into the Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x} matrix suppresses the carrier concentration, and the electrical conductivity actually decreases with the Se content. However, moderate Se doping is effective in enhancing the thermoelectric performance of the n-type Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x}, because of the resulted dramatically decreased thermal conductivity. Analyses indicate that the heightened point-defect scattering induced by Se doping together with the electron–phonon scattering induced by Te doping is responsible for the reduction of lattice thermal conductivity of these compounds.

36 MATERIALS SCIENCE↗