Search NASA⌕ Search

SEARCH · Search NASA

Results for “focused experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Effect of Applied Stress on the Selective Oxidation of Alloy 600 Exposed to PWR Primary Water and Rhines Pack Environments

A mechanistic understanding of corrosion and oxidation processes is crucial to ensure long-term resistance to stress corrosion cracking of Ni-base structural alloys in pressurized water reactor (PWR) primary and secondary systems. Aqueous corrosion of Ni-base alloys under PWR primary water conditions was previously compared to gaseous oxidation with comparable oxygen potentials. However, those studies considered only stress-free conditions, which removes a critical parameter for understanding stress corrosion behaviors. A significant knowledge gap exists for the role of applied stresses on selective internal oxidation in gaseous environments. A micro-4-point-bend jig was designed to facilitate stress in a Rhines Pack set-up. Selective oxidation at different stress and strain conditions was investigated in a series of Rhines Pack experiments for Alloy 600. Focused ion beam milling enabled the extraction of site-specific specimens containing selected high-energy grain boundaries from tensile and compressive stress regions. Analytical transmission electron microscopy was employed to analyze the microstructure and chemical composition of the resulting oxides. Protective surface oxide films and selective intergranular oxides were observed at different conditions. The implications of these fundamental differences are discussed relative to intergranular attack and stress corrosion cracking mechanisms in PWR primary water.

stress, 4-point-bend, selective oxidation, Alloy 6↗

Catalytic Upgrading of Pyrolysis Products for the Production of Sustainable Aviation Fuel

The objective of this project is advance the state-of-technology for a catalytic fast pyrolysis (CFP) + hydrotreating (HT) process to produce sustainable aviation fuel and other biogenic products. Our approach focuses on performing integrated experiments using realistic biomass feedstocks and non-noble metal technical catalyst formulations. CFP is performed in an ex-situ configuration using a fluidized bed reactor without co-fed hydrogen. Research advancements over the past two years include establishing benchmark yield structures and compositional data for each step of the biomass-to-SAF process, demonstrating the ability to produce a cycloalkane-rich SAF product that meets key ASTM 4054 guidelines, generating benchmark characterization data for technical catalyst formulations with an emphasis on determining the unique composition and combustion properties of biogenic coke, and establishing bio-oil critical material attributes to mitigate the risk of plugging during down-stream hydroprocessing. Other impacts from this project include generation of broadly enabling scientific knowledge (12 publications/12 presentations since 2021), engagement with industry partners (Johnson Matthey, ExxonMobil, Phillips 66), and identification of a promising pathway to market that addresses emerging demands for biogenic refinery feedstocks.

biomass↗

Experimental study for subcriticality measurement of fuel debris in the Fukushima Daiichi reactor - 14582

Fuel debris defueling in the Fukushima Daiichi reactors is planned. Furthermore, retrieved fuel debris will be packed and stored in casks for a long time. In these processes, from the viewpoint of criticality safety, the subcriticality of the fuel debris should be confirmed. Although there are some subcriticality measurement methods, the applicability of these methods to the fuel debris must be investigated because the elemental composition and shape of the fuel debris are unknown. In this study, we focus on the exponential experiment method which is able to measure a wide range of subcriticality. Basic experiments to validate the methods were carried out using Toshiba Nuclear Critical Assembly (NCA) and {sup 3}He Position Sensitive Detector (PSD). The decay curves of neutron flux distributions were measured by the PSD detector and fitted to a theoretical formula. The elemental compositions and neutron spectrum of the fuel debris have been estimated with a severe accident code and a Monte Carlo code. In the experiment, the neutron spectrum of the fuel debris was simulated in the NCA core. The porosity of the fuel debris was assumed to be 60%, which corresponds to be H/U=7.5 and Volume Ratio=1.5. In order to evaluate the effect of the uncertainty of the compositions on the measured subcriticality, a homogeneous region and a heterogeneous region were configured in an experimental core. These regions consisted of fuel rods with different UO{sub 2} enrichment zone or different gadolinia concentration zone in the axial direction. The effective multiplication factors deduced by the exponential experiment method were a range of 0.94 to 0.98. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

How important is spatial resolution: Case studies at 48, 12 and 4 km for the U.S., Latin America and Southern Asia

A critical role for regional climate models is downscaling coarse spatial resolution global model simulations of climate change to the much higher resolution required for assessment of regional changes and impacts. But what degree of downscaling is required? Fully coupled global climate models typically have resolutions of at best 100-200 km. The most recent set of IPCC reports suggest that the scale of regional/local impacts to climate change are on the order of 10 km. The scale mismatch is obvious, but less clear is what degree the climate simulations must be downscaled to meet the needs of impacts studies - other non-climate factors might also be crucial or even dominant. We have made a series of simulations with the WRF ARW for the U.S., large portions of Latin America, and South and Southeast Asia. Each set of runs includes a large outer domain at 48 km; an intermediate domain at 12 km (that is the primary basis for model results and interpretations); and one or more 'exploratory' inner domains at 4 km. The latter include regions with complex topography as well as both homogeneous and inhomogeneous land surface types. For each region a multi-year control forced by NCEP reanalyses has been made. Experiments for Asia are focusing on the effects of deforestation, while those for the U.S. and Latin America are focusing on IPCC climate change scenarios (A1FI for the U.S. and A2 for Latin America). Large-scale forcings for the latter two are provided by NCAR CCSM IPCC AR4 simulations. Preliminary results suggest that the higher resolutions have much more structure in standard climate quantities such as temperature or precipitation. Less obvious, however, is how realistic these structures are. In some cases, they clearly follow the better resolution of topography; in other instances the reason is less certain. Furthermore, observational datasets are frequently inadequate in assessing realism, especially for the non-U.S. domains. Finally, this work raises the issue of the trade-off between the length and the resolution of regional climate model simulations. Which is more important - long runs at medium resolution, or shorter runs at higher resolution?

54 ENVIRONMENTAL SCIENCES↗

Probing Exotic Physics With Supernova Neutrinos

Future galactic supernovae will provide an extremely long baseline for studying the properties and interactions of neutrinos. In this paper, we discuss the possibility of using such an event to constrain (or discover) the effects of exotic physics in scenarios that are not currently constrained and are not accessible with reactor or solar neutrino experiments. In particular, we focus on the cases of neutrino decay and quantum decoherence. We calculate the expected signal from a core-collapse supernova in both current and future water Cerenkov, scintillating, and liquid argon detectors, and find that such observations will be capable of distinguishing between many of these scenarios. Additionally, future detectors will be capable of making strong, model-independent conclusions by examining events associated with a galactic supernova's neutronization burst.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Conventional Neutrino Beam Experiments: Present and Future Generations

There are currently four conventional neutrino beams produced around the world serving a total of six different neutrino experiments devoted to a broad range of physics. In this article we discuss the current generation of experiments served by those beamlines, future plans for those beamlines, and plans for yet newer facilities, with a focus on lessons the current generation of experiments can pass on to future generations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Investigating the zonal wind response to SST warming using transient ensemble AGCM experiments

The response of the atmospheric circulation to greenhouse gas-induced SST warming is investigated using large ensemble experiments with two AGCMs, with a focus on the robust feature of the poleward shift of the eddy driven jet. In these experiments, large ensembles of simulations are conducted by abruptly switching the SST forcing on from January 1st to focus on the wintertime circulation adjustment. A hybrid, nite amplitude wave activity budget analysis is performed to elucidate the nonlinear and irreversible aspects of the eddy-mean ow interaction during the adjustment of the zonal wind towards a poleward shifted state. The results conrm the results from earlier more idealized studies, particularly the importance of reduced dissipation of wave activity and the dominant role of the decrease of elective diffusivity in the midlatitudes. Some quantitative discrences do exist between the wave activity budgets of our more realistic experiments and the earlier idealized ones, including larger wave activity tendency and diabatic wave source, and a somewhat greater role of the changing PV gradient in the total reduction of the wave activity dissipation. The relative importance of wave breaking-induced PV mixing versus diabatic PV source in the evolution of the Lagrangian PV gradient is also investigated. The former plays the dominant role in the PV gradient formation during the initial phase of the jet shift, while the latter even opposes the evolution of the Lagrangian PV gradient at times. The possible involvement of the wave reflection level at the poleward flank of the mean jet is also investigated.

54 ENVIRONMENTAL SCIENCES↗

Kinoform optics applied to X-ray photon correlation specroscopy

Moderate-demagnification higher-order silicon kinoform focusing lenses have been fabricated to facilitate small-angle X-ray photon correlation spectroscopy (XPCS) experiments. The geometric properties of such lenses, their focusing performance and their applicability for XPCS measurements are described. It is concluded that one-dimensional vertical X-ray focusing via silicon kinoform lenses significantly increases the usable coherent flux from third-generation storage-ring light sources for small-angle XPCS experiments.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

On the response of rubbers at high strain rates.

In this report, we examine the propagation of tensile waves of finite deformation in rubbers through experiments and analysis. Attention is focused on the propagation of one-dimensional dispersive and shock waves in strips of latex and nitrile rubber. Tensile wave propagation experiments were conducted at high strain-rates by holding one end fixed and displacing the other end at a constant velocity. A high-speed video camera was used to monitor the motion and to determine the evolution of strain and particle velocity in the rubber strips. Analysis of the response through the theory of finite waves and quantitative matching between the experimental observations and analytical predictions was used to determine an appropriate instantaneous elastic response for the rubbers. This analysis also yields the tensile shock adiabat for rubber. Dispersive waves as well as shock waves are also observed in free-retraction experiments; these are used to quantify hysteretic effects in rubber.

36 MATERIALS SCIENCE↗

Archiving Microgravity Flight Data and Samples

To obtain help in evaluating its current strategy for archiving data and samples obtained in microgravity research, NASA's Microgravity Science and Applications Division (MSAD) asked the Space Studies Board's Committee on Microgravity Research for guidance on the following questions: What data should be archived and where should it be kept? In what form should the data be maintained (electronic files, photographs, hard copy, samples)? What should the general format of the database be? To what extent should it be universally accessible and through what mechanisms? Should there be a period of time for which principal investigators have proprietary access? If so, how long should proprietary data be stored? What provisions should be made for data obtained from ground-based experiments? What should the deadline be for investigators placing their data in the archive? How long should data be saved? How long should data be easily accessible? As a prelude to making recommendations for optimum selection and storage of microgravity data and samples, the committee in this report briefly describes NASA's past archiving practices and outlines MSAD's current archiving strategy. Although the committee found that only a limited number of experiments have thus far been archived, it concluded that the general archiving strategy, characterized by MSAD as minimalist, appears viable. A central focus of attention is the Experiment Data Management Plan (EDMP), MSAD's recently instituted data management and archiving framework for flight experiments. Many of the report's recommendations are aimed at enhancing the effectiveness of the EDMP approach, which the committee regards as an appropriate data management method for MSAD. Other recommendations provide guidance on broader issues related to the questions listed above. This report does not address statutory or regulatory records retention requirements.

Source record↗

Thermal barrier coating experience in the gas turbine engine

Thermal Barrier Coatings (TBC), provide thermal insulation and oxidation resistance in an environment consisting of hot combustion gases. TBC's consist of a two layer system. The outer ceramic layer provides good thermal insulation due to the low thermal conductivity of the ceramic coatings used, while the inner metallic bond coat layer provides needed oxidation resistance to the underlying superalloy. Pratt & Whitney has over a decade of experience with several generations of TBC systems on turbine airfoils. This paper will focus on the latest TBC field experience along with a proposed durability model.

Bose, S.↗

Real-Time Payload Operations on the International Space Station

This paper will focus on the challenges that Payload Operations have faced as Payload Utilization has evolved over the last three years of real-time experience. Specifically the paper will focus on the planning challenges and the constant battle over program allocation between core systems and payloads, the process of developing and implementing crew training in a centralized location that is being support by a payload development community spread out all over the US, the unique challenges associated with deployed pressurized payload payloads that are not located within an ISPR, and the importance of documenting specific requirements that the payload development community must implement to get through the crew reviews associated with training and procedures. The authors will focus on specific lessons learned and improvements that have been made in both the streamlining of the processes and the associated documentation.

Cissom, Rick D.↗

Tackling the Reproducibility Problem in Systems Research with Declarative Experiment Specifications

Validating experimental results in the field of computer systems is a challenging task, mainly due to the many changes in software and hardware that computational environments go through. Determining if an experiment is reproducible entails two separate tasks: re-executing the experiment and validating the results. Existing reproducibility efforts have focused on the former, envisioning techniques and infrastructures that make it easier to re-execute an experiment. In this work we focus on the latter by analyzing the validation workflow that an experiment re-executioner goes through. We notice that validating results is done on the basis of experiment design and high-level goals, rather than exact quantitative metrics. Based on this insight, we introduce a declarative format for specifying the high-level components of an experiment as well as describing generic, testable conditions that serve as the basis for validation. We present a use case in the area of storage systems to illustrate the usefulness of this approach. We also discuss limitations and potential benefits of using this approach in other areas of experimental systems research.

97 MATHEMATICS AND COMPUTING↗

Patient Experience in Medical Imaging and Radiation Therapy

The term “patient experience” is currently ubiquitous in health care. Many facilities are striving to improve care by examining how patients interact with and view their organization and the health care professionals who work within it. Although there is a great deal of literature on patient centered care, patient engagement and patient experience in health care generally, there is little focused literature on how this is related to patient experience in medical imaging and radiation therapy. This review article examines the underpinning concepts of patient experience and the factors that contribute to a positive patient experience. These include good communication, care for the patient as an individual, and emotional support. Patients experiencing care in medical imaging and radiation therapy departments have broadly similar expectations, although this can be challenging to provide in a technologically focused, time-limited environment.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Additive Manufacturing, Design, Testing, and Fabrication: A Full Engineering Experience at JSC

I worked on several projects this term. While most projects involved additive manufacturing, I was also involved with two design projects, two testing projects, and a fabrication project. The primary mentor for these was Richard Hagen. Secondary mentors were Hai Nguyen, Khadijah Shariff, and fabrication training from James Brown. Overall, my experience at JSC has been successful and what I have learned will continue to help me in my engineering education and profession long after I leave. My 3D printing projects ranged from less than a 1 cubic centimeter to about 1 cubic foot and involved several printers using different printing technologies. It was exciting to become familiar with printing technologies such as industrial grade FDM (Fused Deposition Modeling), the relatively new SLA (Stereolithography), and PolyJet. My primary duty with the FDM printers was to model parts that came in from various sources to print effectively and efficiently. Using methods my mentor taught me and the Stratasys Insight software, I was able to minimize imperfections, hasten build time, improve strength for specific forces (tensile, shear, etc...), and reduce likelihood of a print-failure. Also using FDM, I learned how to repair a part after it was printed. This is done by using a special kind of glue that chemically melts the two faces of plastic parts together to form a fused interface. My first goal with SLA technology was to bring the printer back to operational readiness. In becoming familiar with the Pegasus SLA printer, I researched the leveling, laser settings, and different vats to hold liquid material. With this research, I was successfully able to bring the Pegasus back online and have successfully printed multiple sample parts as well as functional parts. My experience with PolyJet technology has been focused on an understanding of the abilities/limits, costs, and the maintenance for daily use. Still upcoming will be experience with using a composite printer that uses FDM technology to print plastic while laying an internal filament of Kevlar or carbon-fiber inside the printed material. It has been incredible being exposed to this range of technologies and I feel very fortunate to be ready for virtually any kind of printing technology I come across in the future. Design work played a part in my internship this term as well. Working with Hai Nguyen, I was able to design a set of testing tips and a test frame for use with an Arcjet. The testing tips will be made of several different materials that will possibly be used in the heat shield of the Orion space craft. These designs included technical drawings that were presented to the fabrication shop. The frame design was created from 80/20 (a popular brand of frame construction equipment) and included an order form with pricing for fabrication. An independent design was also done for the virtual reality lab. This design was to create a hand-controller based on a previous design. This final design was sent directly to a 3D printer without technical drawings. Overall, my design work has given me experience with using 80/20, helped improve my CAD (Computer Aided Design) proficiency, and increased my knowledge of how to set up technical drawings for fabrication. The final role I have played in this internship has been to assist with testing of the inflatable technology materials working Khadijah Shariff. I began the internship assisting with permeability testing with the initial plan to continue the testing independently after training. Unfortunately, the testing apparatus suffered a technical failure and had funding pulled which cancelled that portion of the project. Further testing with inflatable technology continued with tensile testing of various stitching methods. This testing took place over a two-days and concluded successfully. Final testing was to be more tensile testing but of straps used to connect various inflatable sections. Unfortunately, the needed grips for the tensile tests could not be located and put the testing on hold. It is possible this round of testing will still take place by the end of the internship if the grips can be found. Overall, this portion of the internship has helped me become familiar with one kind of permeability test as well as a popular tensile/compression testing machine. Finally, I also had the chance to be trained using a metal lathe for making very small tips for a soldering iron. These tips will be used to melt threaded brass inserts into 3D printed plastic. Working with James Brown, I was able to successfully machine a brass rod down to as little as 0.064 inches plus or minus 0.001 inches. It was very rewarding to learn how to best use the machine and become familiar with a skill that will undoubtedly be used again in the future. I have been told by several professional engineers that learning to use a lathe and mill will be invaluable skills in the field. This knocks 50 percent of that goal off and I look forward to learning the mill at some point in the future. As is apparent with this list of projects, my internship was not focused on a single over-arching goal. Instead, I was able to gain experience in a myriad of very different areas. I feel like my time here was spent bouncing from one project to the next. Though sometimes difficult to switch gears, it was very rewarding to be a part of so much in so little time. My career and education will be positively impacted by what I have learned at JSC. My experience with 3D printing has improved my ability to handle many issues that may come up in the future with multiple different technologies. The design work I took part in, especially creating technical drawings, will help me better present designs to any engineer or shop I will encounter. My testing experience has helped me become familiar with a popular kind of tensile test machine that will likely be similar to the kinds I will encounter in the future. Finally, my experience with fabrication has given me a rare opportunity, as an engineer, to take part in the fabrication of a part. This experience will help me better tailor my future designs for the manufacturing process and has given me an appreciation for detailed/delicate machining work. My experience at JSC has been successful and will continue to assist me for a long time within the engineering field.

Zusack, Steven↗

Optimal size of the block in block GMRES on GPUs: computational model and experiments

The block version of GMRES (BGMRES) is most advantageous over the single right hand side (RHS) counterpart when the cost of communication is high while the cost of floating point operations is not. This is the particular case on modern graphics processing units (GPUs), while it is generally not the case on traditional central processing units (CPUs). Here, in this paper, experiments on both GPUs and CPUs are shown that compare the performance of BGMRES against GMRES as the number of RHS increases, with a particular focus on GPU performance. The experiments indicate that there are many cases in which BGMRES is slower than GMRES on CPUs, but faster on GPUs. Furthermore, when varying the number of RHS on the GPU, there is an optimal number of RHS where BGMRES is clearly most advantageous over GMRES. A computational model for the GPU is developed using hardware specific parameters, providing insight towards how the qualitative behavior of BGMRES changes as the number of RHS increase, and this model also helps explain the phenomena observed in the experiments.

97 MATHEMATICS AND COMPUTING↗

Radial Deconsolidation and Leach-Burn-Leach of AGR-3/4 Compacts 8-4 and 7-4

The Advanced Gas Reactor (AGR) Fuel Development and Qualification Program’s third and fourth irradiation experiments (AGR-3/4), originally planned as separate tests, were combined into one test train for irradiation in the Advanced Test Reactor at Idaho National Laboratory (INL). The irradiation test began on December 14, 2011, and ended on April 12, 2014 (Collin 2016). The originally planned AGR-3 and AGR-4 irradiation experiments were both to be focused on obtaining fission product transport data to support improvements in modeling. The AGR-3 experimental plan was focused on gaseous and metallic fission product release from the kernels and diffusion in the coatings during irradiation and postirradiation safety testing. The AGR-4 experimental plan was focused on diffusivities and sorptivities in the compact matrix and reactor graphite (Petti et al. 2005). These goals were combined in the AGR-3/4 irradiation experiment, which consisted of twelve independently monitored capsules that each contained four AGR-3/4 compacts in a single stack surrounded by an inner ring of matrix or graphite and an outer ring of graphite. There were two capsule types: a standard capsule and a fuel body, in which the outer graphite ring included a floor and cap to fully enclose the fuel (Stempien et al. 2018a). The fuel body design supported post-irradiation safety testing of the intact fuel and ring assembly to obtain data on fission product transport and release from matrix and graphite at accident temperatures (Demkowicz 2017).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Radiative Energy Budget Studies Using Observations from the Earth Radiation Budget Experiment (ERBE)

Our research activities under this NASA grant have focused on two broad topics associated with the Earth Radiation Budget Experiment (ERBE): (1) the role of clouds and the surface in modifying the radiative balance; and (2) the spatial and temporal variability of the earth's radiation budget. Each of these broad topics is discussed separately in the text that follows. The major points of the thesis are summarized in section 3 of this report. Other dissertation focuses on deriving the radiation budget over the TOGA COARE region.

Ackerman, Steven A.↗