Search NASA⌕ Search

SEARCH · Search NASA

Results for “frequency variation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Measurements to Understand the Flow Mechanisms Contributing to Tandem-Rotor Outwash

Downwash and outwash characteristics of a model-scale tandem-rotor system in the presence of the ground were analyzed by identifying and understanding the physical mechanisms contributing to the observed flow field behavior. A building block approach was followed in simplifying the problem, separating the effects of the fuselage, effects of one rotor on the other, etc. Flow field velocities were acquired in a vertical plane at four aircraft azimuths of a small-scale tandem rotor system using the particle image velocimetry (PIV) technique for radial distances up to 4 times the rotor diameter. Results were compared against full-scale CH-47D measurements. Excellent correlation was found between the small- and full-scale mean flow fields (after appropriate normalization using rotor and wall jet parameters). Following the scalability analysis, the effect of rotor height on the outwash was also studied. Close to the aircraft, an increase in rotor height above ground decreased the outwash velocity at all aircraft azimuths. However, farther away, the longitudinal and lateral axes of the aircraft showed increasing and decreasing outwash velocities, respectively, with increasing rotor height. Measurements also indicated the presence of large-scale (of the size of the rotor height) shear-layer vortical structures along the ground that could be the source of low-frequency (approximately 1 Hz) flow variation observed in the full-scale measurements. Flow visualization studies and PIV measurements were also made on jets of different sizes to complement the observations made on rotors wherever possible. Baseline rotor measurements were made out-of-ground effect to understand the nature of inflow distribution for realistic rotor configurations and their modified characteristics in the presence of ground. Lastly, a feasibility study on applying high-fidelity CFD simulations for outwash study was conducted using Helios to model an isolated rotor configuration IGE at full-scale Reynolds number. The results were encouraging and demonstrated the practical challenges associated with predicting rotor outwash.

Ramasamy, Manikandan↗

Overview of Primitive Object Volatile Explorer (PrOVE) CubeSat or Smallsat Concept

Here we describe the Primitive Object Volatile Explorer (PrOVE), a smallsat mission concept to study the surface structure and volatile inventory of comets in their perihelion passage phase when volatile activity is near peak. CubeSat infrastructure imposes limits on propulsion systems, which are compounded by sensitivity to the spacecraft disposal state from the launch platform and potential launch delays. We propose circumventing launch platform complications by using waypoints in space to park a deep space SmallSat or CubeSat while awaiting the opportunity to enter a trajectory to flyby a suitable target. In our Planetary Science Deep Space SmallSat Studies (PSDS3) project, we investigated scientific goals, waypoint options, potential concept of operations (ConOps) for periodic and new comets, spacecraft bus infrastructure requirements, launch platforms, and mission operations and phases. Our payload would include two low-risk instruments: a visible image (VisCAM) for 5-10 m resolution surface maps; and a highly versatile multispectral Comet CAMera (ComCAM) will measure 1) H2O, CO2, CO, and organics non-thermal fluorescence signatures in the 2-5 μm MWIR, and 2) 7-10 and 8-14 μm thermal (LWIR) emission. This payload would return unique data not obtainable from ground-based telescopes and complement data from Earth-orbiting observatories. Thus, the PrOVE mission would (1) acquire visible surface maps, (2) investigate chemical heterogeneity of a comet nucleus by quantifying volatile species abundance and changes with solar insolation, (3) map the spatial distribution of volatiles and determine any variations, and (4) determine the frequency and distribution of outbursts.

Clark, Pamela S.↗

Shape Validation and RF Performance of Inflatable Antennas

Inflatable aperture antennas are an emerging technology that is being investigated for potential use in science and exploration missions. In particular, for missions to Mars and beyond, large deployable aperture antennas can provide the antenna gain required for high data rate communications, where the necessary antenna diameter exceeds the available volume of typical launch vehicle platforms. As inflatable aperture antennas have not been proven fully qualified for space missions, the author's Master's Thesis assessed the Ruze equation in characterizing this antenna technology. Inflatable aperture antennas do not follow a parabolic shape, and so the Ruze equation is not applicable due to the macroscopic shape errors of this technology. Therefore, geometric evaluations of the surface profile cannot simply correlate antenna gain degradation with the root-mean-square shape error with a parabolic surface. Consequently, the focus of this work was to derive an accurate mathematical model of an inflatable aperture antenna in order to characterize its Radio Frequency (RF) performance. Calculus of Variations methodologies were used to derive the surface profile shape of the inflatable aperture antenna. Physical Optics techniques were used to generate the antenna pattern profile. Validation testing of the predicted inflatable antenna shape model was performed through use of Laser Radar metrology measurements on an inflatable test article. Assessments of the RF performance of the inflatable aperture antenna, compared with nominally shaped paraboloidal antennas, were obtained through simulations of both technologies using a common diameter, depth, and arc length. Assessments of the RF performance of the inflatable aperture antenna was also performed against itself for changes in distance of the antenna feed location in the axial direction. Whereas the Ruze equation is limited to assessing gain reduction, this effort will also assess beam spreading and first side lobe angle and magnitude. The ability to characterize the RF response of this antenna will provide for an improved understanding of this technology. The accurate representation of the shape of this type of antenna technology will help to identify the most appropriate ways in which this technology could be utilized in planning future communication architectures for NASA missions to Mars and beyond.

Welch, Bryan W.↗

Shape Validation and RF Performance of Inflatable Antennas

Inflatable aperture antennas are an emerging technology that is being investigated for potential use in science and exploration missions. In particular, for missions to Mars and beyond, large deployable aperture antennas can provide the antenna gain required for high data rate communications, where the necessary antenna diameter exceeds the available volume of typical launch vehicle platforms. As inflatable aperture antennas have not been proven fully qualified for space missions, the author's Master's Thesis assessed the Ruze equation in characterizing this antenna technology. Inflatable aperture antennas do not follow a parabolic shape, and so the Ruze equation is not applicable due to the macroscopic shape errors of this technology. Therefore, geometric evaluations of the surface profile cannot simply correlate antenna gain degradation with the root-mean square shape error with a parabolic surface. Consequently, the focus of this work was to derive an accurate mathematical model of an inflatable aperture antenna to in order to characterize its Radio Frequency (RF) performance. Calculus of Variations methodologies were used to derive the surface profile shape of the inflatable aperture antenna. Physical Optics techniques were used to generate the antenna pattern profile. Validation testing of the predicted inflatable antenna shape model was performed through use of Laser Radar metrology measurements on an inflatable test article. Assessments of the RF performance of the inflatable aperture antenna, compared with nominally shaped paraboloidal antennas, were obtained through simulations of both technologies using a common diameter, depth, and arc length. Assessments of the RF performance of the inflatable aperture antenna was also performed against itself for changes in distance of the antenna feed location in the axial direction. Whereas the Ruze equation is limited to assessing gain reduction, this effort will also assess beam spreading and first side lobe angle and magnitude. The ability to characterize the RF response of this antenna will provide for an improved understanding of this technology. The accurate representation of the shape of this type of antenna technology will help to identify the most appropriate ways in which this technology could be utilized in planning future communication architectures for NASA missions to Mars and beyond.

Welch, Bryan↗

Overview of Primitive Volatile Explorer (PrOVE) Cubesat or Smallsat Concept

Here we describe the Primitive Object Volatile Explorer (PrOVE), a smallsat mission concept to study the surface structure and volatile inventory of comets in their perihelion passage phase when volatile activity is near peak. CubeSat infrastructure imposes limits on propulsion systems, which are compounded by sensitivity to the spacecraft disposal state from the launch platform and potential launch delays. We propose circumventing launch platform complications by using waypoints in space to park a deep space SmallSat or CubeSat while awaiting the opportunity to enter a trajectory to flyby a suitable target. In our Planetary Science Deep Space SmallSat Studies (PSDS3) project, we investigated scientific goals, waypoint options, potential concept of operations (ConOps) for periodic and new comets, spacecraft bus infrastructure requirements, launch platforms, and mission operations and phases. Our payload would include two low-risk instruments: a visible image (VisCAM) for 5-10 m resolution surface maps; and a highly versatile multispectral Comet CAMera (ComCAM) will measure 1) H2O, CO2, CO, and organics non-thermal fluorescence signatures in the 2-5 µm MWIR, and 2) 7-10 and 8-14 µm thermal (LWIR) emission. This payload would return unique data not obtainable from ground-based telescopes and complement data from Earth-orbiting observatories. Thus, the PrOVE mission would (1) acquire visible surface maps, (2) investigate chemical heterogeneity of a comet nucleus by quantifying volatile species abundance and changes with solar insolation, (3) map the spatial distribution of volatiles and determine any variations, and (4) determine the frequency and distribution of outbursts.

Zucherman, Aaron↗

Development of Modulator Pulse Stability Measurement Device and Test Results at SLAC

In this paper, the development of a pulse stability measurement device is presented. The measurement accuracy is better than 250uV, about 4.2ppm of a typical 60V input pulse. Pulse signals up to +/- 80V peak can be measured. The device works together with an oscilloscope. The primary function of the measurement device is to provide a precision offset, such that variations in the flattop of the modulator voltage pulse can be accurately resolved. The oscilloscope records the difference between the pulse flattop and the reference for a series of waveforms. The scope math functions are utilized to calculate the rms variations over the series. The frequency response of the device is characterized by the measured cutoff frequency of about 6.5MHz. In addition to detailing the design and calibration of the precision pulse stability device, measurements of SLAC line-type linac modulators and recently developed induction modulators will be presented. Factors affecting pulse stability will be discussed.

43 PARTICLE ACCELERATORS↗

Pilot Plant Reliability Metrics for Grinding and Fast Pyrolysis of Woody Residues

The reliability of biomass size reduction, feeding, and conversion processes remains a critical technical hurdle and important cost driver for biomass conversion systems. While Biorefinery projects have typically focused on scaling up conversion technologies that maximize yield of desired products, e.g. fuels and chemicals, solids handling and reactor feeding systems are often considered secondarily. These are frequently scaled down or adapted from other industries, without a full appreciation of how biomass heterogeneity and variability impact process reliability. Here we present the effects of feedstock variability on relative throughput, mass loss, plant uptime, operator intervention, product yield, and product quality for grinding and fast pyrolysis operations at the pilot scale. Loblolly pine residues were sourced and collected using commercial harvesting techniques. Grinding and pyrolysis experiments were performed at INL's Biomass Feedstock National User Facility and NREL's Thermal and Catalytic Process Development Unit, respectively. Preprocessing throughput using a hammer mill varied between 31-48% of nameplate capacity (5 tons/hr), and fast pyrolysis throughput varied between 57-72% of nameplate capacity (20 kg/hr) for an overall system throughput of 18-35% of nameplate capacity across biomass preprocessing and conversion to pyrolysis oil. Pyrolysis oil yields varied between 46-53% (feedstock carbon to oil, dry basis). Grinder overloads in the size reduction step were more prevalent for lower ash and higher moisture materials. During fast pyrolysis operations, downtime was caused by bridging in the feed and char removal systems and plugging in the condensation system, and significant variation in the type and frequency of operator intervention was observed between feedstocks. Cohesion of solids (feedstock and char) leading to system plugging appeared less problematic for higher ash feedstocks, and differences in condenser plugging behavior between high and low ash feedstocks indicates the composition and physical nature of the deposited material is important for process reliability and is feedstock dependent.

09 BIOMASS FUELS↗

Separation of Yeast Cells from MS2 Viruses Using Acoustic Radiation Force

We report a rapid and robust separation of Saccharomyces cerevisiae and MS2 bacteriophage using acoustic focusing in a microfluidic device. A piezoelectric transducer (PZT) generates acoustic standing waves in the microchannel. These standing waves induce acoustic radiation force fields that direct microparticles towards the nodes (i.e., pressure minima) or the anti-nodes (i.e., pressure maxima) of the standing waves depending on the relative compressidensity between the particle and the suspending liquid.[1] For particles larger than 2 {micro}m, the transverse velocities generated by these force fields enable continuous, high throughput separation. Extensive work in the last decade [2-4] has demonstrated acoustic focusing for manipulating microparticles or biological samples in microfluidic devices. This prior work has primarily focused on experimental realization of acoustic focusing without modeling or with limited one-dimensional modeling estimates. We recently developed a finite element modeling tool to predict the two-dimensional acoustic radiation force field perpendicular to the flow direction in microfluidic devices.[1] Here we compare results from this model with experimental parametric studies including variations of the PZT driving frequencies and voltages as well as various particle sizes and compressidensities. These experimental parametric studies also provide insight into the development of an adjustable 'virtual' pore-size filter as well as optimal operating conditions for various microparticle sizes. Figure 1 shows a typical experimental acoustic focusing result for microparticles (diameter = 2.0 {micro}m) in a 500 {micro}m wide by 200 {micro}m deep microchannel. In this case, the PZT driving frequency and voltage are, respectively, 1.459 MHz and 6.6 V. The microparticles tightly focus (full width half maximum (FWHM) {approx}30 {micro}m) less than 30 s after the initiation of the acoustic field. We simulated the same geometry and operating conditions for comparison. The surface plot in Figure 2 illustrates the two-dimensional pressure field orthogonal to the flow direction (x-direction) from the simulation. The superimposed vector plot shows the acoustic radiation force in this plane. The dark regions and the light regions respectively represent the nodes and anti-nodes of the acoustic pressure field. The corresponding force field predicts acoustic focusing at the center of the microchannel, which is confirmed by the experimental results shown in Figure 1. We demonstrated the separation of Saccharomyces cerevisiae (typical cell size of 4-6 {micro}m depending on the cell growth stage, measured using a Coulter counter) and MS2 bacteriophage (typical diameter {approx}30 nm [5]) using acoustic focusing (Figure 3). A mixture of S. cerevisiae and MS2 labeled with Ribogreen was prepared and injected into one inlet of the microchip (i.e., half of the microchannel was filled with the sample). We varied driving voltages from 1.96 to 4.76 V, while fixing the driving frequency at 1.459 MHz and flow rate at 20 {micro}l/min. The acoustic radiation force did not affect the MS2 viruses, and their concentration profile remained unchanged. Increased driving voltages enhanced the acoustic focusing of the yeast cells thereby achieving good separation. We are able to achieve yields of > 80% and sample purities of > 90% in this continuous-flow sample preparation device.

42 ENGINEERING↗

Adjustable virtual pore-size filter for automated sample preparation using acoustic radiation force

We present a rapid and robust size-based separation method for high throughput microfluidic devices using acoustic radiation force. We developed a finite element modeling tool to predict the two-dimensional acoustic radiation force field perpendicular to the flow direction in microfluidic devices. Here we compare the results from this model with experimental parametric studies including variations of the PZT driving frequencies and voltages as well as various particle sizes and compressidensities. These experimental parametric studies also provide insight into the development of an adjustable 'virtual' pore-size filter as well as optimal operating conditions for various microparticle sizes. We demonstrated the separation of Saccharomyces cerevisiae and MS2 bacteriophage using acoustic focusing. The acoustic radiation force did not affect the MS2 viruses, and their concentration profile remained unchanged. With optimized design of our microfluidic flow system we were able to achieve yields of > 90% for the MS2 with > 80% of the S. cerevisiae being removed in this continuous-flow sample preparation device.

59 BASIC BIOLOGICAL SCIENCES↗

Laser-pumped paraffin-coated cell rubidium frequency standard

We have realized and studied a rubidium atomic frequency standard based on a paraffin-coated cell, exhibiting a short-term frequency stability <3 Multiplication-Sign 10{sup -12} {tau}{sup -1/2} between {tau} = 1 and 100 s. Characterization of the wall-coating is performed by measuring the T{sub 1} and T{sub 2} relaxation times. Perturbations of the medium- to long-term clock stability, due to variations in the laser-intensity, laser frequency, the microwave power shift, and the shifts due to temperature variations are measured and analyzed. A method for reducing the intensity light-shift by detuning the laser frequency and the resulting improvement in clock stability is demonstrated. This work is of relevance for further improvements on Rb cell standards using anti-relaxation wall-coating technology.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dosimetric effects of rotational output variation and x-ray target degradation on helical tomotherapy plans

In this study, two potential sources of IMRT delivery error have been identified for helical tomotherapy delivery using the HiART system (TomoTherapy, Inc., Madison, WI): Rotational output variation and target degradation. The HiArt system is known to have output variation, typically about {+-}2%, due to the absence of a dose servo system. On the HiArt system, x-ray target replacement is required approximately every 10-12 months due to target degradation. Near the end of target life, the target thins and causes a decrease in the beam energy and a softening of the beam profile at the lateral edges of the beam. The purpose of this study is to evaluate the dosimetric effects of rotational output variation and target degradation by modeling their effects and incorporating them into recalculated treatment plans for three clinical scenarios: Head and neck, partial breast, and prostate. Models were created to emulate both potential sources of error. For output variation, a model was created using a sine function to match the amplitude ({+-}2%), frequency, and phase of the measured rotational output variation data. A second model with a hypothetical variation of {+-}7% was also created to represent the largest variation that could exist without violating the allowable dose window in the delivery system. A measured beam profile near the end of target life was used to create a modified beam profile model for the target degradation. These models were then incorporated into the treatment plan by modifying the leaf opening times in the delivery sinogram. A new beam model was also created to mimic the change in beam energy seen near the end of target life. The plans were then calculated using a research version of the PLANNED ADAPTIVE treatment planning software from TomoTherapy, Inc. Three plans were evaluated in this study: Head and neck, partial breast, and prostate. The D{sub 50} of organs at risk, the D{sub 95} for planning target volumes (PTVs), and the local dose difference were used to evaluate the changes in the modified treatment plans. Dosimetric effects from rotational variation were found to be low (less than 1%) for a typical variation of {+-}2%. Even using a variation of {+-}7%, DVH values and dose distributions were altered by less than 2% for all scenarios. The dosimetric effects of target degradation were found to be slightly more significant. For a model using data taken just before target failure, dosimetric differences of 2%-4% were observed in the recalculated plans when compared to the original plans. The largest effects (up to 4.5%) were observed for PTVs that were located at deeper depths as seen in the prostate plan. Overall, the recalculated plans show that the dosimetric effects of rotational variation and target degradation are on the order of 1%-4% for helical tomotherapy on the HiART system and do not pose a risk for significant deviations from the original treatment plan.

61 RADIATION PROTECTION AND DOSIMETRY↗

Remote sensing and snowpack management

The present work describes the use of an airborne electromagnetic sensing system for measuring snowpack depth, density, and water content. A transmitter sends a sequence of pulses of stepped frequencies, and the reflections are measured by a sensitive receiver. The combination of the snowpack and the earth interacts with the electromagnetic wave so as to modify the characteristics of the reflected signals. The variation of the reflected intensity with frequency provides the desired data. A theoretical analysis of return signal and snowpack parameter relationships is given, and the results of experimental verification of the theory are discussed.

Linlor, W. I.↗

Gamma ray burst size-frequency distributions: Spectral selection effects

The effects of spectral variation on the detection of gamma ray bursts were investigated. Selection biases resulting from these effects can account for the reported deviation of the observed size-frequency distribution in peak energy flux from that expected for a simple uniform distribution of sources. Thus these observations as yet provide no clear evidence for structure in the burst source distribution. Because of selection biases, the intrinsic average temperature of the bursts is much harder (kT approximately MeV) than the observed average (approximately 200 KeV).

Higdon, J. C.↗

An exploratory study of a finite difference method for calculating unsteady transonic potential flow

A method for calculating transonic flow over steady and oscillating airfoils was developed by Isogai. The full potential equation is solved with a semi-implicit, time-marching, finite difference technique. Steady flow solutions are obtained from time asymptotic solutions for a steady airfoil. Corresponding oscillatory solutions are obtained by initiating an oscillation and marching in time for several cycles until a converged periodic solution is achieved. The method is described in general terms and results for the case of an airfoil with an oscillating flap are presented for Mach numbers 0.500 and 0.875. Although satisfactory results are obtained for some reduced frequencies, it is found that the numerical technique generates spurious oscillations in the indicial response functions and in the variation of the aerodynamic coefficients with reduced frequency. These oscillations are examined with a dynamic data reduction method to evaluate their effects and trends with reduced frequency and Mach number. Further development of the numerical method is needed to eliminate these oscillations.

Bennett, R. M.↗

Passive Microwave Observation of Diurnal Surface Soil Moisture

Microwave radiometers operating at low frequencies are sensitive to surface soil moisture changes. Few studies have been conducted that have involved multifrequency observations at frequencies low enough to measure a significant soil depth and not be attenuated by the vegetation cover. Another unexplored aspect of microwave observations at low frequencies has been the impact of diurnal variations of the soil moisture and temperature on brightness temperature. In this investigation, observations were made using a dual frequency radiometer (1.4 and 2.65 GHz) over bare soil and corn for extended periods in 1994. Comparisons of emissivity and volumetric soil moisture at four depths for bare soils showed that there was a clear correspondence between the 1 cm soil moisture and the 2.65-GHz emissivity and between the 3-5 cm soil moisture and the 1.4-GHZ emissivity, which confirms previous studies. Observations during drying and rainfall demonstrate that new and unique information for hydrologic and energy balance studies can be extracted from these data.

Jackson, Thomas J.↗

Amplitude variations of whistler-mode signals caused by their interaction with energetic electrons of the magnetosphere

Whistler mode waves that propagate through the magnetosphere exchange energy with energetic electrons by wave-particle interaction mechanisms. Using linear theory, a detailed investigation is presented of the resulting amplitude variations of the wave as it propagates. Arbitrary wave frequency and direction of propagation are considered. A general class of electron distributions that are nonseparable in particle energy and pitch-angle is proposed. It is found that the proposed distribution model is consistent with available whistler and particle observations. This model yields insignificant amplitude variation over a large frequency band, a feature commonly observed in whistler data. This feature implies a certain equilibrium between waves and particles in the magnetosphere over a wide spread of particle energy, and is relevant to plasma injection experiments and to monitoring the distribution of energetic electrons in the magnetosphere.

Bernard, L. C.↗

Fission yield calculation using toy model based on Monte Carlo simulation

Toy model is a new approximation in predicting fission yield distribution. Toy model assumes nucleus as an elastic toy consist of marbles. The number of marbles represents the number of nucleons, A. This toy nucleus is able to imitate the real nucleus properties. In this research, the toy nucleons are only influenced by central force. A heavy toy nucleus induced by a toy nucleon will be split into two fragments. These two fission fragments are called fission yield. In this research, energy entanglement is neglected. Fission process in toy model is illustrated by two Gaussian curves intersecting each other. There are five Gaussian parameters used in this research. They are scission point of the two curves (R{sub c}), mean of left curve (μ{sub L}) and mean of right curve (μ{sub R}), deviation of left curve (σ{sub L}) and deviation of right curve (σ{sub R}). The fission yields distribution is analyses based on Monte Carlo simulation. The result shows that variation in σ or µ can significanly move the average frequency of asymmetry fission yields. This also varies the range of fission yields distribution probability. In addition, variation in iteration coefficient only change the frequency of fission yields. Monte Carlo simulation for fission yield calculation using toy model successfully indicates the same tendency with experiment results, where average of light fission yield is in the range of 90<A<100 and average of heavy fission yield is in about 135<A<145.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Characterization of the relationship of the cure cycle chemistry to cure cycle processing properties

Dynamic Dielectric measurements made over a wide range of frequency provide a sensitive and convenient means for monitoring the cure process in thermosets and thermoplastics. The measurement of dielectric relaxation is one of only a few instrumental techniques available for studying molecular properties in both the liquid and solid states. Furthermore, it is probably the only convenient experimental technique for studying the polymerization process of going from a monomeric liquid of varying viscosity to a crosslinked, insoluble, high temperature solid. The objective of the research is to develop on-line dielectric instrumentation for quantitative nondestructive material evaluation and closed loop smart cure cycle control. The key is to relate the chemistry of the cure cycle process to the dielectric properties of the polymer system by correlating the time, temperature, and frequency dependent dielectric measurements with chemical characterization measurements. Measurement of the wide variation in magnitude of the complex permittivity with both frequency and state of cure, coupled with chemical characterization work, have been shown in the laboratory to have the potential to determine: resin quality, composition and age; cure cycle window boundaries; onset of flow and point of maximum flow; extent of and completion of reaction; evolution of volatiles; T sub g; and, crosslinking and molecular weight buildup.

Kranbuehl, D. E.↗