Search NASA⌕ Search

SEARCH · Search NASA

Results for “higher accuracy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Construction of higher order accurate vortex and particle methods

The standard point vortex method has recently been shown to be of high order of accuracy for problems on the whole plane, when using a uniform initial subdivision for assigning the vorticity to the points. If obstacles are present in the flow, this high order deteriorates to first or second order. New vortex methods are introduced which are of arbitrary accuracy (under regularity assumptions) regardless of the presence of bodies and the uniformity of the initial subdivision.

Nicolaides, R. A.↗
NASA NTRS1993

The NASA/industry Design Analysis Methods for Vibrations (DAMVIBS) program : Bell Helicopter Textron accomplishments

Accurate vibration prediction for helicopter airframes is needed to 'fly from the drawing board' without costly development testing to solve vibration problems. The principal analytical tool for vibration prediction within the U.S. helicopter industry is the NASTRAN finite element analysis. Under the NASA DAMVIBS research program, Bell conducted NASTRAN modeling, ground vibration testing, and correlations of both metallic (AH-1G) and composite (ACAP) airframes. The objectives of the program were to assess NASTRAN airframe vibration correlations, to investigate contributors to poor agreement, and to improve modeling techniques. In the past, there has been low confidence in higher frequency vibration prediction for helicopters that have multibladed rotors (three or more blades) with predominant excitation frequencies typically above 15 Hz. Bell's findings under the DAMVIBS program, discussed in this paper, included the following: (1) accuracy of finite element models (FEM) for composite and metallic airframes generally were found to be comparable; (2) more detail is needed in the FEM to improve higher frequency prediction; (3) secondary structure not normally included in the FEM can provide significant stiffening; (4) damping can significantly affect phase response at higher frequencies; and (5) future work is needed in the areas of determination of rotor-induced vibratory loads and optimization.

Cronkhite, James D.↗
NASA NTRS2004

Determining the Optimum Post Spacing of LIDAR-Derived Elevation Data in Varying Terrain for Flood Hazard Mapping Purposes in North Carolina and Texas

The major flood events in the United States in the past few years have made it apparent that many floodplain maps being used by State governments are outdated and inaccurate. In response, many Stated have begun to update their Federal Emergency Management Agency (FEMA) Digital Flood Insurance Rate Maps. Accurate topographic data is one of the most critical inputs for floodplain analysis and delineation. Light detection and ranging (LIDAR) altimetry is one of the primary remote sensing technologies that can be used to obtain high-resolution and high-accuracy digital elevation data suitable for hydrologic and hydraulic (H&H) modeling, in part because of its ability to "penetrate" various cover types and to record geospatial data from the Earth's surface. However, the posting density or spacing at which LIDAR collects the data will affect the resulting accuracies of the derived bare Earth surface, depending on terrain type and land cover type. For example, flat areas are thought to require higher or denser postings than hilly areas to capture subtle changes in the topography that could have a significant effect on flooding extent. Likewise, if an area has dense understory and overstory, it may be difficult to receive LIDAR returns from the Earth's surface, which would affect the accuracy of that bare Earth surface and thus would affect flood model results. For these reasons, NASA and FEMA have partnered with the State of North Carolina and with the U.S./Mexico Foundation in Texas to assess the effect of LIDAR point density on the characterization of topographic variation and on H&H modeling results for improved floodplain mapping. Research for this project is being conducted in two areas of North Carolina and in the City of Brownsville, Texas, each with a different type of terrain and varying land cover/land use. Because of various project constraints, LIDAR data were acquired once at a high posting density and then decimated to coarser postings or densities. Quality assurance/quality control analyses were performed on each dataset. Cross sections extracted form the high density and then the decimated datasets were individually input into an H&H model to determine the model's sensitivity to topographic variation and the effect of that variation on the resulting water profiles. Additional analysis was performed on the Brownsville, Texas, LIDAR data to determine the percentage of returns that "penetrated" various types of canopy or vegetative cover. It is hoped that the results of these studies will benefit state and local communities as they consider the post spacing at which to acquire LIDAR data (which affects cost) and will benefit FEMA as the Agency assesses the use of different technologies for updating National Flood Insurance Program and related products.

Berglund, Judith↗
NASA NTRS1980

Accuracy of the determination of mean anomalies and mean geoid undulations from a satellite gravity field mapping mission

Improved knowledge of the Earth's gravity field was obtained from new and improved satellite measurements such as satellite to satellite tracking and gradiometry. This improvement was examined by estimating the accuracy of the determination of mean anomalies and mean undulations in various size blocks based on an assumed mission. In this report the accuracy is considered through a commission error due to measurement noise propagation and a truncation error due to unobservable higher degree terms in the geopotential. To do this the spectrum of the measurement was related to the spectrum of the disturbing potential of the Earth's gravity field. Equations were derived for a low-low (radial or horizontal separation) mission and a gradiometer mission. For a low-low mission of six month's duration, at an altitude of 160 km, with a data noise of plus or minus 1 micrometers sec for a four second integration time, we would expect to determine 1 deg x 1 deg mean anomalies to an accuracy of plus or minus 2.3 mgals and 1 deg x 1 deg mean geoid undulations to plus or minus 4.3 cm. A very fast Fortran program is available to study various mission configurations and block sizes.

Jekeli, C.↗
DOE OSTI2024

A High-Order Eulerian–Lagrangian Runge–Kutta Finite Volume (EL–RK–FV) Method for Scalar Nonlinear Conservation Laws

Abstract We present a class of high-order Eulerian–Lagrangian Runge–Kutta finite volume methods that can numerically solve Burgers’ equation with shock formations, which could be extended to general scalar conservation laws. Eulerian–Lagrangian (EL) and semi-Lagrangian (SL) methods have recently seen increased development and have become a staple for allowing large time-stepping sizes. Yet, maintaining relatively large time-stepping sizes post shock formation remains quite challenging. Our proposed scheme integrates the partial differential equation on a space-time region partitioned by linear approximations to the characteristics determined by the Rankine–Hugoniot jump condition. We trace the characteristics forward in time and present a merging procedure for the mesh cells to handle intersecting characteristics due to shocks. Following this partitioning, we write the equation in a time-differential form and evolve with Runge–Kutta methods in a method-of-lines fashion. High-resolution methods such as ENO and WENO-AO schemes are used for spatial reconstruction. Extension to higher dimensions is done via dimensional splitting. Numerical experiments demonstrate our scheme’s high-order accuracy and ability to sharply capture post-shock solutions with large time-stepping sizes.

Chen, Jiajie↗
DOE OSTI2026

Local Spin Density Approximation Strongly Improved by a Better-Informed Local Scaling of Its Self-Interaction Correction

The Perdew−Zunger self-interaction correction (PZSIC) makes density functional approximations (DFAs) exact for all one-electron densities. However, it overcorrects in manyelectron regions, introducing errors for the uniform-density limit, where uncorrected DFAs are exact. The locally scaled PZSIC (LSIC), based on the iso-orbital indicator zσ [which distinguishes single-orbital and slowly varying density regions and is used with the local spin density approximation (LSDA)], restores the uniform-density limit and significantly improves results for many properties, including chemical reaction barrier heights, atomization energies, and ionization potentials. Yet, LSIC performs poorly for weakly bonded systems, leaving many unbound, due to limitations of its iso-orbital indicator. To correct this, in this work we propose a new local scaling, LSIC-α, based on the iso-orbital indicator ασ (which additionally identifies regions of overlapping density tails). A two-parameter scaling function of ασ is fitted to a subset of the nonbonded appropriate norms for the SCAN and r2SCAN meta- GGAs, and tested on many properties of main-group atoms, molecules, and molecular complexes. LSIC-α greatly improves the interaction energies of weakly bonded systems in the S22 data set while retaining LSIC’s accuracy for other properties. This work shows that the errors of LSDA (and presumably of higher-level DFAs) can be largely but not entirely repaired by a proper “do no harm” self-interaction correction.

Approximation↗
DOE OSTI2023

Classification of gaseous UF 6 assay by femtosecond LIBS in the 424.4 nm spectral region using numerical HOGSVD-DTW features

This technical note presents experimental results using numerical features of fs-LIBS data to classify the assay value of a gaseous UF 6 material. Here, the data-driven feature vectors are computed by Higher Order Generalized Singular Value Decomposition (HOGSVD) and Dynamic Time Warp (DTW). The method achieves 96.97% accuracy in spectral classification testing with fs-LIBS samples obtained from a UF 6 material with five known assay values ranging from 0.287% to 61.740%, with 100% accuracy for the four largest assay values ranging from 4.615% to 61.740%.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

A flexible gyro-fluid system of equations

Gyro-fluid equations are velocity space moments of the gyrokinetic equations. Special gyro-Landau-fluid closures have been developed that include the damping due to kinetic resonances by fitting to the collisionless local plasma response functions. This damping allows for accurate linear eigenmodes to be computed with a relatively low number of velocity space moments compared to the number of velocity quadrature points in gyrokinetic codes. However, none of the published gyro-Landau-fluid closure schemes considers the Onsager symmetries of the resulting quasi-linear fluxes as a constraint. Onsager symmetry guarantees that the matrix of diffusivities is positive definite, an important property for the numerical stability of a transport solver. A two-parameter real closure for improving the accuracy of low-resolution gyro-fluid equations, which preserves the Onsager symmetry and allows higher velocity space moments, is presented in this paper. The new linear gyro-fluid system (GFS) is used to extend the TGLF quasi-linear transport model so that it can compute the energy and momentum fluxes due to parallel magnetic fluctuations, completing the transport matrix. The GFS equations do not use a bounce average approximation. The GFS equations are fully electromagnetic with general flux surface magnetic geometry, pitch angle scattering for electron collisions, and subsonic equilibrium toroidal rotation. Using GFS eigenmodes in the quasi-linear TGLF model will be shown to yield a more accurate match to fluxes computed by CGYRO turbulence simulations. In conclusion, prospects for future applications of a quasi-linear theory to new plasma transport regimes and magnetic confinement devices in addition to tokamaks are opened by the flexibility of the GFS eigensolver.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

resbos2 and the CDF W mass measurement

The recent collider detector at fermilab (CDF) W mass measurement of 80 , 433 ± 9 MeV is the most precise direct measurement. However, this result deviates from the Standard Model predicted mass of 80 , 359.1 ± 5.2 MeV by 7 σ . The CDF experiment used an older version of the esos code that was only accurate at NNLL + NLO , while the esos2 code is able to make predictions at N 3 LL + NNLO accuracy. We determine that the data-driven techniques used by CDF capture most of the higher order corrections, and using higher order corrections would have an impact on the CDF result in total at the 10 MeV level. Additionally, we investigate the effects from handling the width of the W boson on the mass, PDF correlations, and scale uncertainties. We find that these contributions are consistent with those obtained by CDF. Published by the American Physical Society 2024

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

A Length Adaptive Algorithm-Hardware Co-design of Transformer on FPGA Through Sparse Attention and Dynamic Pipelining

Transformers are considered one of the most important deep learning models since 2018, in part because it establishes state-of-the-art (SOTA) records and could potentially replace existing Deep Neural Networks (DNNs). Despite the remarkable triumphs, the prolonged turnaround time of Transformer models is a widely recognized roadblock. The variety of sequence lengths imposes additional computing overhead where inputs need to be zero-padded to the maximum sentence length in the batch to accommodate the parallel computing platforms. This paper targets the field-programmable gate array (FPGA) and proposes a coherent sequence length adaptive algorithm–hardware co-design for Transformer acceleration. Particularly, we develop a hardware-friendly sparse attention operator and a length-aware hardware resource scheduling algorithm. The proposed sparse attention operator brings the complexity of attention-based models down to linear complexity and alleviates the off-chip memory traffic. The proposed length-aware resource hardware scheduling algorithm dynamically allocates the hardware resources to fill up the pipeline slots and eliminates bubbles for NLP tasks. Experiments show that our design has very small accuracy loss and has 80.2 × and 2.6 × speedup compared to CPU and GPU implementation, and 4 × higher energy efficiency than state-of-the-art GPU accelerator optimized via CUBLAS GEMM.

Peng, Hongwu↗
NASA NTRS1984

Hydrological planning studies using Landsat-4 Thematic Mapper (TM)

NASA, in cooperation with the U.S. Army Corps of Engineers, is evaluating the capabilities of Landsat 4 Thematic Mapper (TM) data for environmental and hydrological applications. Attention is given to the results of studies conducted at the Clinton River Basin in Michigan and the eastern shore of the Chesapeake Bay in Maryland. In the former, the evaluation conducted was for the band combinations: (1) 2, 3, and 4; (2) 3, 4, and 5; (3) 3, 4, 5, and 6; and (4) all seven bands. In the latter case, Multispectral Scanner (MSS) and TM data were classified for combinations (1), (3) and (4). Wetland classification accuracy for the 7-band TM data in this study was found to be 9 percent higher than with MSS data, allowing more reliable and accurate monitoring.

Gervin, J. C.↗
NASA NTRS1990

Measurement of structure motion by means of a moving light sheet

The elaboration of an optical system which measures the displacement and velocity of large flexible space structures is reviewed. The motion-measuring system, comprised of a laser, optics, motorized mirror, two photodiodes and electronics, is designed to allow feedback for configuration control of flexible structures. A motor or scanner is employed to sweep the light sheet. The range of motion was shown to be 2 inches, and information was received at a rate of 30 Hz. The uncertainty in displacement measurement was better than +0.01 inch from a distance of 16 feet. The results are considered to be very good for two scanning light sheet systems. Higher sample rates and a more constant speed would improve the rotating mirror option, and the accuracy and range of the scanning mirror option could be upgraded as well. Both setups are shown to be viable noncontact measuring methods for the displacement and velocity of large space structures.

Tcheng, Ping↗
NASA NTRS1993

The upper clouds of Venus: Determination of the scale height from NIMS-Galileo infrared data

The 3-5 micrometer thermal emission of the nightside of Venus, recorded by the Near-Infrared Mapping Spectrometer (NIMS) instrument at the time of the Galileo flyby of Venus, is analysed to infer the properties of the upper cloud boundary. From the global maps of Venus at fixed wavelengths, the limb darkening of the flux is measured at several latitudes, within each infrared channel. By using the nominal Pioneer Venus thermal profile, these data give access to two parameters: the cloud deck temperature and the cloud scale height. It is verified independently, from the NIMS spectra, that this thermal profile is consistent with all the NIMS observations, and that the thermal structure does not vary significantly in the latitude range (25 deg S, 30 deg N). Within this range, the cloud scale height is found to be constant with latitude, and is H = 5.2 km, with an accuracy of about 15%, taking into account the various sources of theoretical and observational uncertainties. At higher latitudes, the temperature profile becomes more isothermal and the presented method to retrieve H is no longer valid.

Roos, M.↗
NASA NTRS1998

Aeroacoustic Codes for Rotor Harmonic and BVI Noise. CAMRAD.Mod1/HIRES: Methodology and Users' Manual

This document details the methodology and use of the CAMRAD.Mod1/HIRES codes, which were developed at NASA Langley Research Center for the prediction of helicopter harmonic and Blade-Vortex Interaction (BVI) noise. CANMAD.Mod1 is a substantially modified version of the performance/trim/wake code CANMAD. High resolution blade loading is determined in post-processing by HIRES and an associated indicial aerodynamics code. Extensive capabilities of importance to noise prediction accuracy are documented, including a new multi-core tip vortex roll-up wake model, higher harmonic and individual blade control, tunnel and fuselage correction input, diagnostic blade motion input, and interfaces for acoustic and CFD aerodynamics codes. Modifications and new code capabilities are documented with examples. A users' job preparation guide and listings of variables and namelists are given.

Boyd, D. Douglas, Jr.↗
NASA NTRS2012

Membrane Shell Reflector Segment Antenna

The mesh reflector is the only type of large, in-space deployable antenna that has successfully flown in space. However, state-of-the-art large deployable mesh antenna systems are RF-frequency-limited by both global shape accuracy and local surface quality. The limitations of mesh reflectors stem from two factors. First, at higher frequencies, the porosity and surface roughness of the mesh results in loss and scattering of the signal. Second, the mesh material does not have any bending stiffness and thus cannot be formed into true parabolic (or other desired) shapes. To advance the deployable reflector technology at high RF frequencies from the current state-of-the-art, significant improvements need to be made in three major aspects: a high-stability and highprecision deployable truss; a continuously curved RF reflecting surface (the function of the surface as well as its first derivative are both continuous); and the RF reflecting surface should be made of a continuous material. To meet these three requirements, the Membrane Shell Reflector Segment (MSRS) antenna was developed.

Fang, Houfei↗
NASA NTRS1984

Status of Understanding for Gear Materials

Today's gear designer has a large selection of possible gear materials to choose from. The choice of which material to use should be based on the requirements of the application and will include the operating conditions of load, speed, and temperature in addition to reliability, weight, noise limitation, accuracy, and cost. The plastic materials are generally low in cost with low strength capabilities and are suitable for many light-duty applications. Die-cast alloy and sintered powder-metal gears are also fairly inexpensive and will operate at higher loads and temperatures than plastic gears. The three types of cast iron offer a medium-strength gear at a cost that varies with the accuracy of machining requirements. Gears can be manufactured from several aluminum alloys for lightweight and medium cost and may be anodized for improved load capacity. The copper alloys, bronze and brass, are more costly but have good sliding and wear properties that are useful for worm gear applications. The hot-forged powder-metal gears have the advantage of medium cost with good accuracy and high strength. Several low- to medium alloy steels are available for gear design and most can be heat treated for added strength. The medium-alloy gear materials offer high strength when case hardened and will satisfy most high-load medium-temperature applications. For more severe load, speed, and temperature requirements the advanced high temperature alloys must be used. These include EX-53, CBS 600, Vasco X-2, Super Nitralloy (5Ni-2Al), and forged AISI M-50. As the requirements become more stringent, the cost will also increase. It is necessary that the gear designer have a working knowledge of the various gear materials in order to match the most economical material with the design requirements.

Dennis P Townsend↗
DOE OSTI2021

Quality control and crop characterization framework for multi-temporal UAV LiDAR data over mechanized agricultural fields

Recent developments in remote sensing are enabling automatic, high resolution, and non-destructive survey of agriculture fields, providing the key basis for advancing plant breeding. Among the used remote sensing modalities, LiDAR has attracted wide attention for its ability to directly provide accurate 3D information. Despite the increasing utilization of LiDAR technology in phenotyping, there is still a lack of effective quality control strategies, in particular, quality control of LiDAR data collected on a multi-temporal basis. This study proposes a targetless framework for multi-temporal LiDAR data quality control and crop characterization in mechanized agricultural fields. Features extracted from the fields – terrain patches and row/alley locations – are utilized for evaluating the vertical and planimetric relative accuracy of the point clouds. Row/alley locations in the field are automatically identified from the point clouds based on the assumption that higher point density and/or higher elevation correspond to plant locations. The performance of the proposed quality control strategies is evaluated using multi-temporal datasets collected in agricultural fields of different sizes, orientation, crops, and growth stages. The result shows that the net vertical and planimetric discrepancies between multi-temporal point clouds are ±3 cm and ±8 cm, respectively. While the former reflects the actual accuracy of the point clouds, the latter is a combined effect of the LiDAR point cloud accuracy, rasterization artifacts, crop type, growth pattern, and wind condition during data acquisition. In terms of row and alley detection, the result shows that the proposed strategy achieves high performance and can deal with different planting orientation, crop types, growth stages, canopy cover, and planting density. In conclusion, this study presents a quality control framework for multi-temporal LiDAR data. Finally, the row and alley detection leads to automated extraction of plots, and hence facilitates the use of remotely sensed data for automated phenotyping.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1958

Aerodynamic Performance and Static Stability and Control of Flat-Top Hypersonic Gliders at Mach Numbers from 0.6 to 18

A study is made of aerodynamic performance and static stability and control at hypersonic speeds. In a first part of the study, the effect of interference lift is investigated by tests of asymmetric models having conical fuselages and arrow plan-form wings. The fuselage of the asymmetric model is located entirely beneath the wing and has a semicircular cross section. The fuselage of the symmetric model was centrally located and has a circular cross section. Results are obtained for Mach numbers from 3 to 12 in part by application of the hypersonic similarity rule. These results show a maximum effect of interference on lift-drag ratio occurring at Mach number of 5, the Mach number at which the asymmetric model was designed to exploit favorable lift interference. At this Mach number, the asymmetric model is indicated to have a lift-drag ratio 11 percent higher than the symmetric model and 15 percent higher than the asymmetric model when inverted. These differences decrease to a few percent at a Mach number of 12. In the course of this part of the study, the accuracy to the hypersonic similarity rule applied to wing-body combinations is demonstrated with experimental results. These results indicate that the rule may prove useful for determining the aerodynamic characteristics of slender configurations at Mach numbers higher than those for which test equipment is really available. In a second part of the study, the aerodynamic performance and static stability and control characteristics of a hypersonic glider are investigated in somewhat greater detail. Results for Mach numbers from 3 to 18 for performance and 0.6 to 12 for stability and control are obtained by standard text techniques, by application of the hypersonic stability rule, and/or by use of helium as a test medium. Lift-drag ratios of about 5 for Mach numbers up to 18 are shown to be obtainable. The glider studied is shown to have acceptable longitudinal and directional stability characteristics through the range of Mach numbers studied. Some roll instability (negative effective dihedral) is found at Mach numbers near 12.

Syvertson, Clarence A↗