SEARCH · Search NASA

Results for “interface properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Metal-dielectric interactions

Metal direlectric surface interactions and dielectric films on metal substrates were investigated. Since interfacial interaction depends so heavily on the nature of the surfaces, analytical surface tools such as Auger emission spectroscopy, X-ray photoelectron spectroscopy and field ion microscopy were used to assist in surface and interfacial characterization. The results indicate that with metals contacting certain glasses in the clean state interfacial, bonding produces fractures in the glasses while when a film such as water is present, fractures occur in the metal near the interface. Friction forces were used to measure the interfacial bond strengths. Studies with metals contacting polymers using field ion microscopy revealed that strong bonding forces could develop being between a metal and polymer surface with polymer transferring to the metal surface in various ways depending upon the forces applied to the surface in contact. With the deposition of refractory carbides, silicides and borides onto metal and alloy substrates the presence of oxides at the interface or active gases in the deposition plasma were shown to alter interfacial properties and chemistry. Auger ion depth profile analysis indicated the chemical composition at the interface and this could be related to the mechanical, friction, and wear behavior of the coating.

Buckley, D. H.↗

NASA NTRS1983

Metallurgical and tensile property analysis of several silicon carbide/titanium composite systems

Several silicon-carbide fiber reinforced titanium matrix composite systems were investigated to determine composite degradation mechanisms and to develop techniques to minimize loss of mechanical properties during fabrication and in service. Emphasis was on interface control by fiber or matrix coatings. Fibers and matrix materials were sputter coated with various metals to determine the effects of the coatings on basic fiber properties, fiber-matrix interactions, and on composite properties. The effects of limited variations in fabrication temperature on composite properties were determined for composites consolidated by standard press-diffusion-bonding techniques.

Brewer, W. D.↗

NASA NTRS1988

Interfacial adhesion: Theory and experiment

Adhesion, the binding of different materials at an interface, is of general interest to many branches of technology, e.g., microelectronics, tribology, manufacturing, construction, etc. However, there is a lack of fundamental understanding of such diverse interfaces. In addition, experimental techniques generally have practical objectives, such as the achievement of sufficient strength to sustain mechanical or thermal effects and/or have the proper electronic properties. In addition, the theoretical description of binding at interfaces is quite limited, and a proper data base for such theoretical analysis does not exist. This presentation will review both experimental and theoretical aspects of adhesion in nonpolymer materials. The objective will be to delineate the critical parameters needed, governing adhesion testing along with an outline of testing objectives. A distinction will be made between practical and fundamental objectives. Examples are given where interfacial bonding may govern experimental consideration. The present status of theory is presented along wiith recommendations for future progress and needs.

Ferrante, John↗

NASA NTRS1988

Interfacial adhesion - Theory and experiment

Ferrante, John↗

DOE OSTI2018

Microstructural and Mechanical Properties of Hot Roll Bonded Titanium Alloy/Low Carbon Steel Plate

In this paper, a titanium alloy and low carbon steel were bonded via hot rolling in a vacuum, and the effect of roll bonding temperature and reduction ratio on the microstructural and mechanical properties of the plate was studied. When the bonding temperature was between 850 and 1050 °C, the shear strength of the interface increased with an increasing reduction ratio from 18 to 70%. At a bonding temperature of 950 °C and at a rolling reduction ratio of 70%, the best bonding strength was obtained, and a shear fracture occurred on the low carbon steel matrix. At 1050 °C, brittle compounds, i.e., TiC, FeTi, and Fe{sub 2}Ti, formed at the interface, which decreased the bonding strength. The large reduction ratio can break up compounds at the interface and extrude fresh metal for bonding, thereby increasing the bonding strength.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Te/CdTe and Al/CdTe Interfacial Energy Band Alignment by Atomistic Modeling

A synergistic approach that incorporates first-principles atomistic modeling with numerical device simulations is used to systematically evaluate the role of heterointerfaces within metal-chalcogenide-based photovoltaic technologies. Two interfaces involving either a tellurium back contact or aluminum back electrode combined with a cadmium telluride absorber layer within cadmium-telluride-based thin-film solar cells are investigated on an atomic scale to determine the mechanisms contributing to variations in device performance. Electronic structures and predicted charge transport behavior with respect to cadmium and tellurium termination of the absorber layer are studied along the polar oriented CdTe{111} facets. The computational methodology reveals a noticeable contrast between the Schottky barrier forming Al/CdTe interface versus the Type I Te/CdTe heterojunction. Greater band bending features are exhibited by the cadmium termination as opposed to the tellurium termination for each interface case. Subsequent device modeling suggests that 3.6% higher photovoltaic conversion efficiency is achievable for the cadmium termination relative to the tellurium termination of the Te/CdTe interface. Based strictly on an idealistic representation, both interface models show the importance of atomic-scale interfacial properties for cadmium telluride solar cell device performance with their bulk properties being validated in comparison to published experimental data. Here, the synergistic approach offers a suitable method to analyze solar cell interfaces through a predictive computational framework for the engineering and optimization of metal-chalcogenide-based thin-film photovoltaic technologies.

Green’s function↗

NASA NTRS1985

Composite structural materials

Various topics relating to composite structural materials for use in aircraft structures are discussed. The mechanical properties of high performance carbon fibers, carbon fiber-epoxy interface bonds, composite fractures, residual stress in high modulus and high strength carbon fibers, fatigue in composite materials, and the mechanical properties of polymeric matrix composite laminates are among the topics discussed.

Loewy, R. G.↗

DOE OSTI2020

DFT modelling of explicit solid–solid interfaces in batteries: methods and challenges

Density Functional Theory (DFT) calculations of electrode material properties in high energy density storage devices like lithium batteries have been standard practice for decades. By contrast, DFT modelling of explicit interfaces in batteries arguably lacks universally adopted methodology and needs further conceptual development. In this paper, we focus on solid–solid interfaces, which are ubiquitous not just in all-solid state batteries; liquid-electrolyte-based batteries often rely on thin, solid passivating films on electrode surfaces to function. We use metal anode calculations to illustrate that explicit interface models are critical for elucidating contact potentials, electric fields at interfaces, and kinetic stability with respect to parasitic reactions. The examples emphasize three key challenges: (1) the “dirty” nature of most battery electrode surfaces; (2) voltage calibration and control; and (3) the fact that interfacial structures are governed by kinetics, not thermodynamics. To meet these challenges, developing new computational techniques and importing insights from other electrochemical disciplines will be beneficial.

25 ENERGY STORAGE↗

DOE OSTI2018

Conducting properties of nanocomposite polymer electrolytes based on polyethylene glycol diacrylate and SiO{sub 2} nanoparticles at the interface with a lithium electrode

Nanocomposite polymer electrolytes based on polyethylene glycol diacrylate and 1 M LiBF{sub 4} solution in γ-butyrolactone with addition of SiO{sub 2} nanoparticles were synthesized and studied. Resistance measurement at the Li/electrolyte and Li/nanocomposite electrolyte interface by the time-resolved electrochemical impedance showed its significant decrease in the presence of SiO{sub 2} nanoparticles. Charge-discharge cycling of prototypes of Li/LiFePO{sub 4} batteries for 50 cycles also showed the advantage of using nanocomposite polymer electrolytes over electrolytes without SiO{sub 2} additives.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2018

Influence of Rotation Rate on Microstructure and Comprehensive Performance of FSWed Mg Alloy

Die-casting AZ31 Mg alloys were successfully friction stir welded at a constant welding speed and different rotation rates. More uniform and fine grains were obtained at the rotation rate of 1400 rpm due to more suitable temperature for dynamic recrystallization in this welding condition. In addition, the intensity of (0001) texture in stir zone increased with the increasing rotation rate. The results of mechanical property test indicated joint with rotation rate of 1400 rpm had better tensile property, which was associated with fine grains, uniform transition in the interface between thermo-mechanically affected zone and stir zone as well as more favorable Schmidt factor for basal slip and twinning. The corrosion resistance of joints increased with the increasing rotation rate, which is significantly related to the (0001) texture with basal plane parallel to the corroded surfaces.

36 MATERIALS SCIENCE↗

NASA NTRS1985

Electrical characterization of plasma-grown oxides on gallium arsenide

Plasma-grown GaAs oxides and their interfaces have been characterized by measuring the electrical properties of metal-oxide-semiconductor capacitors and of Schottky junctions. The current transport mechanism in the oxide at high electrical field was found to be Frankel-Poole emission, with an electron trap center at 0.47 eV below the conduction band of the oxide. The interface-state density, evaluated from capacitance and conductance measurements, exhibits a U-shaped interface-state continuum extending over the entire band gap. Two discrete deep states with high concentration are superimposed on this continuum at 0.40 and 0.70 eV below the conduction band. The results obtained from measurements on Schottky junctions have excluded the possibility that these two deep states originate from plasma damage. Possible origins of these states are discussed in this paper.

Hshieh, F. I.↗

NASA NTRS1972

Penny-shaped interface crack between an elastic layer and a half space.

The axially symmetric elastostatic problem for a layer bonded to a half space with different material properties is considered. It is assumed that the bi-material interface contains a penny-shaped crack the surfaces of which are subjected to known tractions. The solution of the problem is reduced to that of a system of singular integral equations of the second kind. A numerical example for an aluminum-epoxy material combination is given. The stress intensity factors and the strain energy release rate are calculated and are given as functions of layer thickness-to-crack radius ratio.

Erdogan, F.↗

DOE OSTI2020

Polyphenol-Sensitized Atomic Layer Deposition for Membrane Interface Hydrophilization

Improvements in energy-water systems will necessitate fabrication of high-performance separation membranes. To this end, interface engineering is a powerful tool for tailoring properties, and atomic layer deposition (ALD) has recently emerged as a promising and versatile approach. However, most non-polar polymeric membranes are not amenable to ALD processing due to the absence of nucleation sites. Here, a sensitization strategy for ALD-coating is presented, illustrated by membrane interface hydrophilization. Facile dip-coating with polyphenols effectively sensitizes hydrophobic polymer membranes to TiO2 ALD coating. Tannic acid-sensitized ALD-coated membranes exhibit outstanding underwater crude oil repulsion and rigorous mechanical stability through bending and rinsing tests. As a result, these membranes demonstrate outstanding crude oil-in-water separation and reusability compared to untreated membranes or those treated with ALD without polyphenol pretreatment. A possible polyphenol-sensitized ALD mechanism is proposed involving initial island nucleation followed by film intergrowth. This polyphenol sensitization strategy enriches the functionalization toolbox in material science, interface engineering, and environmental science.

36 MATERIALS SCIENCE↗

DOE OSTI2019

Solderability of AZ31B Magnesium Alloy Coated by Copper and Strength of the Solder Joints

Magnesium alloys are promising as light materials, while their high chemical reactivity makes them difficult to be soldered. In this study, the AZ31B alloy was pretreated by zincification and coated by an electrodeposited Cu layer, and then soldered with Sn-58Bi solder in air furnace. The microstructure and properties of the AZ31B/Cu(Zn)/SnBi solder joints were characterized to evaluate the solderability of the Cu-coated Mg alloy and the influence of soldering on the Cu coating. It was found that the Cu coating is dense, and little defect exists along the Cu(Zn)/AZ31B interface. The soldering process has little negative effect on the bonding between the Cu coating and the AZ31B substrate, and the AZ31B/Cu(Zn)/SnBi solder joints of high metallurgical quality were obtained. Tensile fracture of the solder joint occurs mainly in the solder, with no peeling of the Cu coating. Under shear loading, cracks initiate inside the SnBi solder and the final fracture of the joint occurs around the Cu{sub 6}Sn{sub 5}/solder interface or along the Cu(Zn)/AZ31B interface. The tensile and shear strength of the AZ31B/Cu(Zn)/SnBi solder joints are close to that of the SnBi/Cu solder joints. It is demonstrated that the Cu-coated Mg alloy shows superior solderability and can be soldered by the Sn-based low-melting solder in air.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Identification of a quasi-liquid phase at solid–liquid interface

Abstract An understanding of solid–liquid interfaces is of great importance for fundamental research as well as industrial applications. However, it has been very challenging to directly image solid–liquid interfaces with high resolution, thus their structure and properties are often unknown. Here, we report a quasi-liquid phase between metal (In, Sn) nanoparticle surfaces and an aqueous solution observed using liquid cell transmission electron microscopy. Our real-time high-resolution imaging reveals a thin layer of liquid-like materials at the interfaces with the frequent appearance of small In nanoclusters. Such a quasi-liquid phase serves as an intermediate for the mass transport from the metal nanoparticle to the liquid. Density functional theory-molecular dynamics simulations demonstrate that the positive charges of In ions greatly contribute to the stabilization of the quasi-liquid phase on the metal surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1987

N2O fluxes at the soil-atmosphere interface in various ecosystems and the global N2O budget

The overall purpose of this research task is to study the effects of soil properties and ecosystem variables on N2O exchanges at the soil-atmosphere interface, and to assess their effects on the globle N2O budget. Experimental procedures are implemented in various sites to measure the source/sink relations of N2O at the soil-atmosphere interface over prolonged periods of time as part of the research of biogeochemical cycling in terrestrial ecosystems. A data-base for establishing quantitative correlations between N2O fluxes and soil and environmental parameters that are of potential use for remote sensing, is being developed.

Banin, Amos↗

DOE OSTI2022

Enriched immersed boundary method (EIBM) for interface-coupled multi-physics and applications to convective conjugate heat transfer

It is challenging to develop numerical methods that simultaneously maintain accuracy of resolving boundary conditions and mesh flexibility to handle the interface in interface-coupled multi-physics problems involving large property discontinuity. On the one hand, boundary-fitted methods possess high accuracy in capturing the interfacial phenomenon but involve complicated volumetric mesh generation, mesh-motion, and even re-meshing procedures. On the other hand, immersed boundary methods (IBM) provide mesh flexibility but sometimes suffer from inferior interface representations, leading to poor enforcement of boundary conditions. This paper presents an enriched immersed boundary method (EIBM) to overcome this challenge and demonstrates its efficacy in conjugate heat transfer, a representative example in interface-coupled multi-physics systems that have implications for many industrial processes. Further, the core technique of the method is to enhance IBM’s accuracy of the fluid–solid interface by enriching the degrees of freedom of the cut elements to enforce temperature and flux compatibilities and resolve all the physical unknowns on the background mesh to simplify the volumetric mesh generation. We implement the EIBM under the framework of a variational multiscale formulation for coupled Navier–Stokes and thermodynamics equations. The enriched DoFs enable better enforcement of temperature and flux compatibilities with large conductivity ratios across the fluid–solid interface. At the same time, the immersed nature of the proposed method still attains mesh flexibility. The EIBM’s accuracy is thoroughly evaluated through a set of examples, ranging from benchmark problems with analytical solutions to real-world cooling processes of a moving metallic structure with complex geometry.

42 ENGINEERING↗

DOE OSTI2021

Exploring the Spatial Control of Topotactic Phase Transitions Using Vertically Oriented Epitaxial Interfaces

Engineering oxygen vacancy formation and distribution is a powerful route for controlling the oxygen sublattice evolution that affects diverse functional behavior. The controlling of the oxygen vacancy formation process is particularly important for inducing topotactic phase transitions that occur by transformation of the oxygen sublattice. Here we demonstrate an epitaxial nanocomposite approach for exploring the spatial control of topotactic phase transition from a pristine perovskite phase to an oxygen vacancy-ordered brownmillerite (BM) phase in a model oxide La 0.7 Sr 0.3 MnO 3 (LSMO). Incorporating a minority phase NiO in LSMO films creates ultrahigh density of vertically aligned epitaxial interfaces that strongly influence the oxygen vacancy formation and distribution in LSMO. Combined structural characterizations reveal strong interactions between NiO and LSMO across the epitaxial interfaces leading to a topotactic phase transition in LSMO accompanied by significant morphology evolution in NiO. Using the NiO nominal ratio as a single control parameter, we obtain intermediate topotactic nanostructures with distinct distribution of the transformed LSMO-BM phase, which enables systematic tuning of magnetic and electrical transport properties. The use of self-assembled heterostructure interfaces by the epitaxial nanocomposite platform enables more versatile design of topotactic phase structures and correlated functionalities that are sensitive to oxygen vacancies.

36 MATERIALS SCIENCE↗