Search NASA⌕ Search

SEARCH · Search NASA

Results for “interface velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Spin and valley transport in monolayers of MoS{sub 2}

We investigate theoretically quantum transport and Goos-Hänchen (GH) effect of electrons in a p-n-p junction on monolayers of MoS{sub 2}. We find that the transmission properties of spin-up (spin-down) electrons in K valley are the same with spin-down (spin-up) electrons in K′ valley due to the time-reversal symmetry. The GH shifts for the transmitted K and K′ beams in the n-p interface are in the opposite direction, and GH shifts for the spin-up and spin-down electron beams at the same valley have different values in the same direction due to the different group velocities. Therefore, the spin-up and spin-down electrons can be separated after passing a sufficiently long channel created by a p-n-p junction. These features provide us a new way to generate a fully spin- and valley-polarized current in monolayers of MoS{sub 2}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Laterally Converging Duct Flows - Part 4. Temporal Behaviour in the Viscous Layer

Since insight into entropy generation is a key to increasing efficiency and thereby reducing fuel consumption and/or waste and -- for wall-bounded flows -- most entropy is generated in the viscous layer, we examine the transient behavior of its dominant contributor there for a non-canonical flow. New measurements in oil flow are presented for the effects of favorable streamwise pressure gradients on temporal entropy generation rates and, in the process, on key Reynolds-stress-producing events such as sweep front passage and on the deceleration/outflow phase of the overall bursting process. Two extremes have been considered: (1) a high pressure gradient, nearing "laminarization," and (2), for comparison, a low pressure gradient corresponding to many earlier experiments. In both cases, the peak temporal entropy generation rate occurs shortly after passage of the ejection/sweep interface. Whether sweep and ejection rates appear to decrease or increase with the pressure gradient depends on the feature examined and the manner of sampling. When compared using wall coordinates for velocities, distances and time, the trends and magnitudes of the transient behaviors are mostly the same. The main effects of the higher pressure gradient are (1) changes in the time lag between detections -- representing modification of the shape of the sweep front and the sweep angle with the wall, (2) modification of the magnitude of an instantaneous Reynolds shear stress with wall distance and (3) enlarging the sweeps and ejections. Results new for both low and high pressure gradients are the temporal behaviors of the dominant contribution to entropy generation; it is found to be much more sensitive to distance from the wall than to streamwise pressure gradient.

42 ENGINEERING↗

Investigation of Surface Skidding Response of PBX 9501 and PBX 9502

Introduction: Assess the hazards of handling polymer bonder explosives(PBX) for the case of skidding with grit particles in the frictional interface. High explosive (HE) materials tested: PBX 9501 and 9502. High melting point materials at the skidding interface between HE and a substrate is known to increase the probability of ignition by creating hot spots not subject to reduced heating from the melting of HE material. Skidding occurred at peak forces of 6-26 kN normal force, and 0.6-3.4 kN of frictional force. Velocities for skidding range from 5-30 m/s, see figure 7. Sparse amounts of 300 μm silica grit is applied loosely to the HE surface before testing. Previous works have tested ignition by grit. Testing parameters include angle of impact, drop height, grit size, grit density, substrate material. This study focuses on pre ignition conditions and detailed thermal imaging of the frictional interface. Conclusions: Temperature hot spots were observed at high points in HE surface topology. These high points may be created by grit particles. Since these points impact first high frictional work is concentrated and quickly increases temperature. Small amounts of grit do not affect the overall frictional force but do concentrate the frictional work to create hot spots.

36 MATERIALS SCIENCE↗

A mechanism for reduced compression in indirectly driven layered capsule implosions

High-yield implosions on the National Ignition Facility rely on maintaining low entropy in the deuterium–tritium fuel, quantified by its adiabat, in order to efficiently couple energy to the hot spot through high compression of the fuel layer. We present very-high-resolution xRAGE simulation results that study the impacts of interfacial mixing and the jetting of materials due to surface defects, defects on internal interfaces, voids, and engineering features on fuel layer compression. Defects and voids are typically neglected in implosion simulations due to their small size and three-dimensional geometry. Our results showed that supersonic jets of material arise through weak spots in the shell at peak implosion velocity that prevent uniform compression of the fuel layer even when they do not introduce contaminant into the hot spot. This occurs despite maintaining low fuel entropy, since the formation of the weak spots involves nonradial displacement of fuel mass. In contrast, simulations show that fuel–ablator mixing due to interfacial instabilities has a much smaller impact on compression. We show that defects on interior interfaces of plastic capsules decrease compression by 15% to 25% and interfacial mixing between the ablator and fuel decreases compression by less than 1% for implosions with plastic or high-density carbon (HDC) ablators. For low adiabat implosions, the impact of jetting seeded by the support tent can also decrease the compression by 25%. We demonstrate that the inclusion of interior defects in simulations can explain the inferred compression in two fielded plastic capsule implosions and that the inclusion of voids, for which available characterization has large uncertainties, in simulations of HDC capsule implosions has a qualitatively consistent impact. This mechanism offers a potential explanation for persistently overestimated fuel compression in design simulations of layered implosions on the National Ignition Facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A single crystal plasticity finite element formulation with embedded deformation twins

Deformation twinning is an important plastic deformation mechanism in some polycrystalline metals such as titanium and magnesium. In this paper, we present a novel crystal plasticity finite element framework that accounts for deformation twinning explicitly, in addition to crystallographic slip. Within this computational framework, deformation twins are treated as weak discontinuities embedded within individual finite elements, such that a jump in the velocity gradient field is introduced (via the discretized gradient operator) between the twinned and untwinned crystalline regions, taking into account compatibility and traction continuity conditions at the interface between these two regions. The deformation gradient is multiplicatively split into elastic and plastic parts in the untwinned region, as is customary in finite-deformation crystal plasticity formulations. A different multiplicative decomposition of the deformation gradient into elastic, plastic (slip), and twinning parts is adopted in the twinned region, allowing deformation twinning to be accounted for as an additional mode of plastic deformation. Here, a stochastic model is used to predict twin nucleation at grain boundaries, and the evolution of the length and thickness of the twinned region under subsequent deformation is taken into account.

36 MATERIALS SCIENCE↗

Broad-band trajectory mechanics

We present here a trajectory-based solution to the elastodynamic equation of motion that is valid across a wide range of seismic frequencies. That is, the derivation of the solution does not invoke a high-frequency assumption or require that the medium have smoothly varying properties. The approach, adopted from techniques used in quantum dynamics, produces a set of coupled ordinary differential equations for the trajectory, the slowness vector and the elastic wave amplitude along the ray path. The trajectories may be determined by a direct solution of the governing equations or derived as the by-product of a numerical wavefield simulation. Synthetic tests with interfaces and layers containing increasingly narrow transition zones indicate that the conventional high-frequency trajectories associated with the eikonal equation bend too sharply into high-velocity regions as the wavelength exceeds the transition zone width. Tests in a velocity model, based upon mapped structural surfaces from the Geysers geothermal field in California, indicate that discrepancies between high-frequency and broad-band trajectories can exceed several hundred metres at wavelengths of 1 Hz. An application to a crosswell tomographic imaging experiment demonstrates that the technique provides a basis for the seismic monitoring of fluid flow along narrow features such as fracture zones.

58 GEOSCIENCES↗

SU-E-J-42: Customized Deformable Image Registration Using Open-Source Software SlicerRT

Purpose: SlicerRT is a flexible platform that allows the user to incorporate the necessary images registration and processing tools to improve clinical workflow. This work validates the accuracy and the versatility of the deformable image registration algorithm of the free open-source software SlicerRT using a deformable physical pelvic phantom versus available commercial image fusion algorithms. Methods: Optical camera images of nonradiopaque markers implanted in an anatomical pelvic phantom were used to measure the ground-truth deformation and evaluate the theoretical deformations for several DIR algorithms. To perform the registration, full and empty bladder computed tomography (CT) images of the phantom were obtained and used as fixed and moving images, respectively. The DIR module, found in SlicerRT, used a B-spline deformable image registration with multiple optimization parameters that allowed customization of the registration including a regularization term that controlled the amount of local voxel displacement. The virtual deformation field at the center of the phantom was obtained and compared to the experimental ground-truth values. The parameters of SlicerRT were then varied to improve spatial accuracy. To quantify image similarity, the mean absolute difference (MAD) parameter using Hounsfield units was calculated. In addition, the Dice coefficient of the contoured rectum was evaluated to validate the strength of the algorithm to transfer anatomical contours. Results: Overall, SlicerRT achieved one of the lowest MAD values across the algorithm spectrum, but slightly smaller mean spatial errors in comparison to MIM software (MIM). On the other hand, SlicerRT created higher mean spatial errors than Velocity Medical Solutions (VEL), although obtaining an improvement on the DICE to 0.91. The large spatial errors were attributed to the poor contrast in the prostate bladder interface of the phantom. Conclusion: Based phantom validation, SlicerRT is capable of achieving comparable DIR accuracy to commercial programs such as MIM and VEL.

60 APPLIED LIFE SCIENCES↗

Novel and effective surface passivation for high efficiency n- and p-type Silicon solar cell

The project objective was to develop a novel Si surface passivation method using chalcogens, sulfur (S) and/or selenium (Se), as passivating elements, to withstand industry-standard high temperature contacting and metallization schemes for p-type Si based passivated emitter and rear contact (p-PERC) solar cells. The back surface passivation of PERC cells has been improved drastically with the invention and successful application of an Al 2 O 3 passivation layer. However, the front n + diffused junction surface is still poorly passivated by the standard amorphous silicon nitride (SiNx) anti-reflection coating (ARC) layer. This project sought to address the passivation challenges of both front n+ emitter and undiffused p-Si back surface. Improved p-PERC solar cell performance with open circuit voltage (V OC ) > 680 mV and efficiency of 22% were targeted to validate superior defect passivation properties as compared to standard SiO 2 / Al 2 O 3 passivation. During this project, we systematically investigated process-structure-properties-performance relationships of this novel advanced defect passivation approach. The S/Se passivation was carried out by reacting industrial Czochralski (Cz) Si wafers in H 2 S and H 2 Se gases in a chemical vapor deposition (CVD) reactor at temperatures up to 700°C. After an exhaustive optimization of the process parameters (temperature, time, and gas concentration), we established an optimized process and demonstrated extremely low surface recombination velocities (SRVs) of 1.5 cm/s and 8 cm/s on n-type and p-type Si, respectively, by S-passivation. In-depth surface and interface characterization were performed using soft x-ray and photoelectron spectroscopies (XPS, UPS, XES), combined with capacitance-voltage-frequency (C-V-f) measurements, to decipher the surface chemical/electronic structure and interface defect state densities. These measurements provided critical understanding of the defect passivation mechanism and elucidated the presence of surface S-Si bonds, a reduction of surface dipoles, and low interface state densities (D it ) < 10 11 cm -2 ev -1 . We also found that the Se-passivation is inferior to the S-passivation (by at least one order of magnitude in SRV). Application of the optimized S-passivation to the n+ diffused emitter surface led to a low surface recombination current density, J0 ≈ 40 fA/cm 2 (~ 1/4 of the industry-standard SiNx-passivation), and high implied V OC (686 mV) in p-PERC solar cell structures. The S-passivation process also was found to improve the bulk quality of the p-type Si, better than the SiO 2 or Al 2 O 3 passivation processes. After successful demonstration of efficient passivation of Si surface defects by S, we extensively studied the air, thermal, and illumination stability of the passivation structure. S-passivation itself degrades in air due to competing reactions with moisture and oxygen to form oxides, which can be eliminated by a SiNx capping layer (also acting as a anti-reflective coating). After SiNx process optimization, we demonstrated illumination and thermally stable S-passivation with SRV < 5 cm/s and J 0 < 80 fA/cm 2 . These enhancements in Si passivation, incorporated into p-PERC cells, achieved an efficiency of 19.93% with V OC = 649 mV, using manufacturing metallization and contacting schemes. The low cell performance (cell V OC is much less than the implied V OC = 686 mV, anticipated from surface passivation) was identified due to degradation of S-passivation during the metal firing step (out-diffusion of S from the Si interface to the SiNx surface). The S-passivation of Si surfaces shows significant promise with excellent passivation quality, essential for high performance (high V OC , high efficiency) solar cells. Integration of this innovative defect passivation into devices, however, demands further development of the capping layer, low temperature (<700°C) metallization process, and/or engineering of advanced device structures. Surface passivation-dominated advanced Si solar cells, such as tunnel oxide passivated contacts and Si heterojunctions, are increasingly of interest due to their high-performance potential and will have a growing photovoltaic market share in the near future.

14 SOLAR ENERGY↗

XCT System for Harvesting In-Current Hydrokinetic Energy from Low-Velocity Sites

The Project demonstrated the functionality of a cross cutting (XCT) type turbine in laboratory and open water testing. The fundamental design approach of locating small axial rotors near the ends of driving spars, which pull the rotors through the water at a multiple of the free-stream velocity eliminates the need (and thus the cost) for a gearbox and torque resisting structures. This configuration, however, introduces the complexity of transmitting electricity across a rotating interface. Even so, cost models indicate that depending on the anchoring and mooring system, LCOE less than $0.10/kWh should be possible in high capacity-factor sites with non-reversing currents.

13 HYDRO ENERGY↗

A high speed data acquisition and analysis system for transonic velocity, density, and total temperature fluctuations

The high speed Dynamic Data Acquisition System (DDAS) is described which provides the capability for the simultaneous measurement of velocity, density, and total temperature fluctuations. The system of hardware and software is described in context of the wind tunnel environment. The DDAS replaces both a recording mechanism and a separate data processing system. The data acquisition and data reduction process has been combined within DDAS. DDAS receives input from hot wires and anemometers, amplifies and filters the signals with computer controlled modules, and converts the analog signals to digital with real-time simultaneous digitization followed by digital recording on disk or tape. Automatic acquisition (either from a computer link to an existing wind tunnel acquisition system, or from data acquisition facilities within DDAS) collects necessary calibration and environment data. The generation of hot wire sensitivities is done in DDAS, as is the application of sensitivities to the hot wire data to generate turbulence quantities. The presentation of the raw and processed data, in terms of root mean square values of velocity, density and temperature, and the processing of the spectral data is accomplished on demand in near-real-time- with DDAS. A comprehensive description of the interface to the DDAS and of the internal mechanisms will be prosented. A summary of operations relevant to the use of the DDAS will be provided.

Clukey, Steven J.↗

Estimation of minority carrier diffusion lengths in InP/GaAs solar cells

Minority carrier diffusion length is one of the most important parameters affecting the solar cell performance. An attempt is made to estimate the minority carrier diffusion lengths is the emitter and base of InP/GaAs heteroepitaxial solar cells. The PC-1D computer model was used to simulate the experimental cell results measured at NASA Lewis under AMO (air mass zero) spectrum at 25 C. A 16 nm hole diffusion length in the emitter and a 0.42 micron electron diffusion length in the base gave very good agreement with the I-V curve. The effect of varying minority carrier diffusion lengths on cell short current, open circuit voltage, and efficiency was studied. It is also observed that the front surface recombination velocity has very little influence on the cell performance. The poor output of heteroepitaxial cells is caused primarily by the large number of dislocations generated at the interfaces that propagate through the bulk indium phosphide layers. Cell efficiency as a function of dislocation density was calculated and the effect of improved emitter bulk properties on cell efficiency is presented. It is found that cells with over 16 percent efficiencies should be possible, provided the dislocation density is below 10(exp 6)/sq cm.

Jain, R. K.↗

Precise Motion Control of Hybrid Hydraulic Electric Architecture (HHEA)

Off-highway heavy-duty vehicles have been long-standing users of hydraulic systems for power transmission and control. However, traditional hydraulic systems suffer from significant energy losses which lead to increased operating costs and a larger carbon footprint due to higher CO2 emissions. Improving the efficiency of these mobile machines is crucial not only for reducing their environmental impact but also for saving billions of dollars in operating costs. Currently, the state-of-the-art Load Sensing Architecture uses throttling valves for control, which significantly reduces its efficiency and does not recuperate energy from over-running loads. Researchers have developed several architectures such as Common Pressure Rail systems, Displacement Control, STEAM, and Electrohydraulic Architecture to improve the efficiency of off-road mobile machines. However, each of these architectures has its drawbacks. To increase system efficiency and take advantage of electrification benefits, our research group has developed a novel Hybrid Hydraulic-Electric Architecture (HHEA). The HHEA can significantly improve efficiency, decrease the size of electrical components, and maintain control performance. This new architecture has the potential to revolutionize the off-highway mobile machine industry and lead to a more sustainable future. The HHEA uses a set of common pressure rails to provide the majority of power to the actuators via power-dense hydraulics and uses electric motors for precise control and power modulation. In the context of off-road mobile machines, energy savings are undoubtedly important but it is equally important to consider the machines’ ability to perform tasks with precision and accuracy according to given commands. Therefore, precise motion control is of utmost importance to maintain the utility of Hybrid Hydraulic-Electric Architecture (HHEA). The HHEA presents a unique challenge to motion control due to the discrete pressure changes that occur when the system switches between selected pressure rails. These changes are made to minimize system inefficiencies or to keep the system within the torque capability of the electric motor. Hence, it is important to solve the motion control challenges for HHEA. This thesis aims at developing an effective motion control strategy for HHEA. The dissertation presents a two-tiered control strategy for HHEA, comprising a high-level and a low-level controller. The primary responsibility of the high- level controller is to optimize energy efficiency by making informed pressure rail selections. On the other hand, the low-level controller is focused on achieving precise motion control of the HHEA, which is crucial for realizing the desired reference trajectories. To achieve this, the low-level controller utilizes a passivity-based backstepping integral controller as the nominal control, which handles the motion control between two pressure rail switches. Additionally, a separate least norm controller is utilized as a transition controller to manage motion control during pressure rail transitions. The effectiveness of the combined control strategy is demonstrated through experiments conducted on two hardware-in-the-loop testbeds. Furthermore, the HHEA is installed on the boom and stick actuators of a backhoe arm to build a Human-in-the-Loop system that a human operator can control. A real-time rail switching algorithm is developed to determine pressure rail switching based on present duty cycle information from the operator. Modifications have been made to the human-machine interface to achieve more intuitive control. Modifications include performing control in the task-oriented coordinates, incorporating pressure feedback to enhance control with physical interaction, and using velocity field control to simplify multi-degree-of-freedom tasks and to enable novice operators to perform them with reduced risk, improved efficiency, and productivity. The research in this dissertation makes significant contributions to the field of off-road mobile machine control, providing a novel and effective control strategy for the HHEA, and demonstrating the potential for simplified machine operation.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Molecular Processes Underlying the Structure and Assembly of Thin Films and Nanoparticles at Complex interfaces

Since 1995 we have pursued a number of different studies that are quite diverse in nature but with the common theme of using novel laser based methods to study important processes at buried interfaces. Studies of Corrosion, Passivation on n-GaAs(100)Methanol Photoelectrochemical Cell In these studies we have used picosecond photoluminescence and electrochemical studies to understand the GaAs/methanol interface. In our most extensive set of studies we conducted photo-illumination and XPS experiments to understand the chemistry occurring in the GaAs/methanol photoelectrochemical during photoexcitation. An important distinction between photocorrosion and photoetching of GaAs is elucidated by these studies. The dependence of GaAs photocorrosion on light intensity has been explored to better understand intrinsic differences between the lamplight studies and the picosecond photoluminescence studies. The effect of coating the GaAs with a sulfide layer prior to immersion in the cell has also been explored. This last result has led us to examine n-GaAs as a function of crystallographic orientation after exposure to aqueous Na 2 S containing solutions has been studied as a function of crystallographic orientation of the GaAs surface. The (100) and (110) surfaces are relatively similar, with significant amounts of As-S species present at the interface. The (111)B surface lacks this constituent, but shows significant amounts of metallic As. The XPS results have been correlated with the results of previous photocorrosion and passivation studies conducted in a photoelectrochemical cell. The studies indicate that the metallic As present at (111)B surface contributes strongly to the large surface recombination velocity found there, and to the inability of Na 2 S to passivate the (111)B surface. SAMS Under Water: Water Molecular Structure and Bonding at Hydrophobic Surfaces In these DOE sponsored studies we have been interested in learning the similarities and differences in how water behaves at hydrophobic self-assembled monolayer (SAMS)/water interfaces relative to the organic liquid/water interfaces. Several monolayer films have been examined in these studies using a combination of vibrational sum frequency spectroscopy (VSFS), contact angle measurements and AFM. At the hydrocarbon monolayer/water interface we find that water has a weak bonding interaction with the monolayer film that results in an orientation of water at the terminus of these hydrocarbon chains. The water-film interaction is still present for fluorinated films but it is found to be considerably weaker. Hydration and Surfactant Adsorption at Salt/Water Interfaces This set of studies has examined the molecular characteristics of the CaF 2 /water interface using VSFS. Our first studies detailed the structure and orientation of water molecules adsorbed at this mineral surfaces including studies of the surface in the presence of aqueous solutions of salts. These studies have been followed by a series of static and time-resolved studies of the adsorption of carboxylic acid containing organics at this surface, specifically carboxylic acid surfactants and acetic acid. In the latter we have developed a new method for time resolved studies that involve sequential wavelength tuning and automated control of spatial beam overlap at the target can probe amplitude changes of sum-frequency resonances in widely spaced infrared regions. This offers great advantages for the study of the synchronism of molecular processes at interfaces. This approach is particularly suitable to investigate the synchronization of interfacial processes such as surfactant adsorption at charged mineral surfaces. Macromolecular Assembly at Liquid/Liquid Interfaces Macromolecular assembly at the interface between water and a hydrophobic surface underlies some of the most important biological and environmental processes on the planet. Our work has examined polymer adsorption and assembly of carboxylic acid-containing polyelectrolytes at the carbon tetrachloride–water interface, a model system for an oil–water interface. Using VSFS and interfacial tension techniques, these unique set of studies identify the factors that dictate whether or not polyelectrolytes will adsorb to the oil–water interface and also describe the specifics of the adsorption process that depend upon factors such as polymer size, charge density, hydrophobicity, conformation, and the effect of metal ion electrostatics and bonding. The systems studied include polyelectrolytes polyacrylic acid (PAA) and polymethylacrylic acid (PMA) of different polymer sizes and under different aqueous solution conditions. The studies are the first to show the highly ordered nature of the adsorption of the first monolayer with subsequent monolayers disordered. The second set of studies have examined how peptoid nanosheets assemble at the oil/water interface. Peptoid nanosheets are a recently discovered class of two-dimensional (2D) nanomaterial, which form from the self-assembly of a sequence-specific peptoid polymer at an air-water interface. Nanosheet formation occurs first through the assembly of a peptoid monolayer and subsequent compression into a bilayer structure. In these highly successful studies we have shown that the oil-water interface provides another opportunity for growth of these unique and highly ordered peptoid sheets. The monolayer formed at this interface are found through surface spectroscopic measurements to be highly ordered and electrostatic interactions between the charged moieties, namely carboxylate and ammonium residues, of the peptoid are essential in the ability of these peptoids to form ordered nanosheets at the oil-water interface.

36 MATERIALS SCIENCE↗

Two-dimensional lift-up problem for a rigid porous bed

The present study analytically reinvestigates the two-dimensional lift-up problem for a rigid porous bed that was studied by Mei, Yeung, and Liu [“Lifting of a large object from a porous seabed,” J. Fluid Mech. 152, 203 (1985)]. Mei, Yeung, and Liu proposed a model that treats the bed as a rigid porous medium and performed relevant experiments. In their model, they assumed the gap flow comes from the periphery of the gap, and there is a shear layer in the porous medium; the flow in the gap is described by adhesion approximation [D. J. Acheson, Elementary Fluid Dynamics (Clarendon, Oxford, 1990), pp. 243-245.] and the pore flow by Darcy’s law, and the slip-flow condition proposed by Beavers and Joseph [“Boundary conditions at a naturally permeable wall,” J. Fluid Mech. 30, 197 (1967)] is applied to the bed interface. In this problem, however, the gap flow initially mainly comes from the porous bed, and the shear layer may not exist. Although later the shear effect becomes important, the empirical slip-flow condition might not physically respond to the shear effect, and the existence of the vertical velocity affects the situation so greatly that the slip-flow condition might not be appropriate. In contrast, the present study proposes a more general model for the problem, applying Stokes flow to the gap, the Brinkman equation to the porous medium, and Song and Huang’s [“Laminar poroelastic media flow,” J. Eng. Mech. 126, 358 (2000)] complete interfacial conditions to the bed interface. The exact solution to the problem is found and fits Mei’s experiments well. The breakout phenomenon is examined for different soil beds, mechanics that cannot be illustrated by Mei’s model are revealed, and the theoretical breakout times obtained using Mei’s model and our model are compared. The results show that the proposed model is more compatible with physics and provides results that are more precise.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A high-order discontinuous Galerkin method for wave propagation through coupled elastic-acoustic media

We introduce a high-order discontinuous Galerkin (dG) scheme for the numerical solution of three-dimensional (3D) wave propagation problems in coupled elastic-acoustic media. A velocity-strain formulation is used, which allows for the solution of the acoustic and elastic wave equations within the same unified framework. Careful attention is directed at the derivation of a numerical flux that preserves high-order accuracy in the presence of material discontinuities, including elastic-acoustic interfaces. Explicit expressions for the 3D upwind numerical flux, derived as an exact solution for the relevant Riemann problem, are provided. The method supports h-non-conforming meshes, which are particularly effective at allowing local adaptation of the mesh size to resolve strong contrasts in the local wavelength, as well as dynamic adaptivity to track solution features. The use of high-order elements controls numerical dispersion, enabling propagation over many wave periods. We prove consistency and stability of the proposed dG scheme. To study the numerical accuracy and convergence of the proposed method, we compare against analytical solutions for wave propagation problems with interfaces, including Rayleigh, Lamb, Scholte, and Stoneley waves as well as plane waves impinging on an elastic-acoustic interface. Spectral rates of convergence are demonstrated for these problems, which include a non-conforming mesh case. Finally, we present scalability results for a parallel implementation of the proposed high-order dG scheme for large-scale seismic wave propagation in a simplified earth model, demonstrating high parallel efficiency for strong scaling to the full size of the Jaguar Cray XT5 supercomputer.

97 MATHEMATICS AND COMPUTING↗

Computational Studies of Structures and Dynamics of 1, 3-Dimethylimidazolim Salt Liquid and their Interfaces Using Polarizable Potential Models

The structures, thermodynamics, dynamical properties of bulk and air/liquid interfaces of three ionic liquids, 1,3-dimethylimidazolium [dmim]+, Cl-, Br-, and I- are studied using molecular dynamics techniques. In bulk melts, the radial distribution functions reveal a significant long-range structural correlation in these ionic liquids. From the angular distribution analysis, the imidazolium rings are found to lie parallel to each other at short distances, consistent with the structures observed in the crystal state. The single-ion dynamics are studied via mean-square-displacements, velocity and orientational correlation functions. The diffusion coefficients and reorientational times are found to be much smaller than H2O. We also observe that anion size plays an important role in the dynamics of ionic liquids. The computed density profiles of the ionic liquid/vapor interface exhibit oscillatory behavior, indicative of surface layering at the interface. Further analysis reveals that the [dmim]+ ions show preferred orientation at the interface with the ring parallel to the surface and methyl group attached to the ring pointing into the vapor phase. The computed surface tensions indicated small differences between these ionic liquids and are inline with recent experimental measurements. The calculated potential drops of these ionic liquids are found to be small and negative. These results could imply that the cation dipoles are likely to orient in the plane that parallel to the surface normal axis. This work was supported by the U.S. Department of Energy's (DOE) Office of Basic Energy Sciences, Chemical Sciences program. The Pacific Northwest National Laboratory is operated by Battelle for DOE.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-solid and multi-fluid diffuse interface model: Applications to dynamic fracture and fragmentation

We extend the model of diffuse solid–fluid interfaces developed earlier by authors of this paper to the case of arbitrary number of interacting hyperelastic solids. Plastic transformations of solids are taken into account through a Maxwell type model. The specific energy of each solid is given in separable form: it is the sum of a hydrodynamic part of the energy depending only on the density and the entropy, and an elastic part of the energy which is unaffected by the volume change. It allows us to naturally pass to the fluid description in the limit of vanishing shear modulus. In spite of a large number of governing equations, the model has a quite simple mathematical structure: it is a duplication of a single visco-elastic model. The model is well posed both mathematically and thermodynamically: it is hyperbolic and compatible with the second law of thermodynamics. The resulting model can be applied in the situations involving an arbitrary number of fluids and solids. In particular, we show the ability of the model to describe spallation and penetration phenomena occurring during high velocity impacts.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High-Pressure Geophysical Properties of Fcc Phase FeH X

Face centered cubic (fcc) FeHX was synthesized at pressures of 18-68 GPa and temperatures exceeding 1,500 K. Thermally quenched samples were evaluated using synchrotron X-ray diffraction (XRD) and nuclear resonant inelastic X-ray scattering (NRIXS) to determine sample composition and sound velocities to 82 GPa. To aid in the interpretation of nonideal (X≠1) stoichiometries, two equations of state for fcc FeH X were developed, combining an empirical equation of state for iron with two distinct synthetic compression curves for interstitial hydrogen. Matching the density deficit of the Earth's core using these equations of state requires 0.8-1.1 wt % hydrogen at the core-mantle boundary and 0.2-0.3 wt % hydrogen at the interface of the inner and outer cores. Furthermore, a comparison of Preliminary Reference Earth Model (PREM) to a Birch's law extrapolation of our experimental results suggests that an iron alloy containing approximate to 0.8-1.3 wt % hydrogen could reproduce both the density and compressional velocity (V P ) of the Earth's outer core.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗