Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructural engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Implementation of Disruptive Designs for Gas Turbine Components Utilizing Additive Manufacturing

Electron beam melting (EBM) is an additive manufacturing process used to print metallic components with complex geometries for aerospace applications. A preheating characteristic enables this technology to avoid large accumulation of residual stress during printing. However, cracking mechanisms particularly in Ni-based superalloys are associated with not only residual stress but also with microstructure (i.e., solidification morphology, transient evolution of γ'). Siemens is committed to AM technology for gas turbine applications. The ability to novel predictive designs of turbine blades would reduce process development time and allow acquisition of key microstructure and performance data early in a design campaign. Siemens initiated a project to establish the design rules for the fabrication of non-printable Nibased superalloys. This phase 1 program demonstrates the feasibility for virtual fabrication of the actual blade geometries through EBM process.

42 ENGINEERING↗
DOE OSTI2020

Grain Refinement Effect on the Hot-Tearing Resistance of Higher-Temperature Al–Cu–Mn–Zr Alloys

The hot-tearing resistance of Al-Cu-Mn-Zr (ACMZ) alloys was investigated as a step toward introducing these new cast alloys for severe duty, higher-temperature applications, such as cylinder heads for down-sized, turbocharged automotive engines. Alloy Cu compositions were varied from 5 to 8 wt.%. Targeted Ti levels were 0.02, 0.1, and 0.2 wt.% via additions of the Al–5Ti–1B master alloy. Hot-tearing resistance was assessed by visual examination and ranking of the cracking severity in a multi-arm permanent mold casting. It was found that at high impurity contents (Fe and Si of 0.2 wt.% each), the Al–Cu–Mn–Zr alloy with 4.95 wt.% Cu exhibited the poorest hot-tearing resistance, irrespective of the grain refining amount. Microstructural analysis indicated an effective reduction in the grain size, as the Ti additions were increased to 0.02 and 0.1 wt.% Ti via the Al–Ti–B grain refiner. The finest grain size was attained with a 0.1 wt.% Ti. Based on the hot-tearing evaluation, it was found that the additional grain refining via the Al–5Ti–1B master alloy at 0.1 wt.% Ti significantly reduces the hot-tearing susceptibility at Cu contents greater than 7.3 wt.% for ACMZ alloys with low Fe and Si. These findings indicate that the best hot-tearing resistance was observed at a grain refiner level of 0.1 wt.% Ti and high Cu content (greater than 7.3 wt.%). This study to indicates that these Al–Cu–Mn–Zr alloys, which possess excellent microstructural stability and mechanical properties at elevated temperatures, can also possess excellent hot-tearing resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Meso-scale modeling of UO2 nuclear fuel to high burnup

To improve the economics of light water reactors for commercial nuclear energy generation, utility operators are seeking to obtain regulatory approval to run UO2 fuel to higher levels of burnup. One potential impediment to obtaining this approval is the phenomenon of fuel fragmentation, relocation, and dispersal (FFRD). FFRD can result when fuel experiences a rapid temperature transient, such as that occurring during a Loss Of Coolant Accident (LOCA). FFRD has historically been most associated with the rim region in UO2 fuel pellets, where the phenomenon of fragmentation is also referred to as pulverization due to the small size of the fragments. More recent evidence suggests that the so-called “dark zone” (due to its appearance in micrographs) that can be observed in the mid-radial regions of high burnup fuel is also susceptible to FFRD. Although empirical fuel performance models have been developed that can adequately predict pulverization in the rim region under typical LWR conditions, a scientific understanding of what underlies fuel restructuring and subsequent FFRD is lacking even in the rim region, and no models are currently available for the behavior the dark zone. To address these challenges, the U.S. Department of Energy’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program has employed a multi-scale modeling approach to improve scientific understanding and develop new fuel performance models. In this talk, I will focus on meso-scale efforts, which form a crucial link between atomic-scale and engineering-scale models. Phase-field modeling combined with cluster dynamics is used to predict the restructuring process in the rim region. Phase-field fracture modeling, informed by atomistic simulations, is used to predict the onset of pulverization in the rim region. Combining these techniques together allows the extent of rim pulverization to be predicted. The formation and evolution of the dark zone has also been simulated with the phase-field method, using an improved approach to vacancy source term parameterization. The work shows the important impact of microstructure on fuel performance.

fracture↗
DOE OSTI2024

7 Innovations in high-rate composite manufacturing: integrating additive manufacturing with compression molding process

Advanced composites play a pivotal role in modern engineering, offering exceptional strength-to-weight ratios and tailored properties, essential for various industries. High-rate composite manufacturing techniques have rapid production capabilities, which are essential for meeting the demands of industries requiring cost-saving, efficiency, and quick turnaround times. This chapter explores the Additive Manufacturing- Compression Molding (AM-CM) system developed by Oak Ridge National Laboratory (ORNL) for advanced composites manufacturing. The AM-CM system integrates additive manufacturing with compression molding, facilitating the production of polymer composite parts with superior mechanical properties and meticulously controlled microstructures. This innovative system not only ensures precise material deposition but also operates as a fast composite manufacturing process, enhancing productivity and performance, which are needed attributes across industrial applications. Through comprehensive mechanical testing and microstructural analysis, AM-CM promotes remarkable fiber alignment and reduced porosity in composite parts compared to alternative thermoplastic high-rate composite manufacturing methods. Furthermore, AM-CM enables overmolding reinforcement using continuous carbon fiber and supports selective reinforcement through customizable toolpaths. It also facilitates the production of hybrid materials to achieve tailored mechanical properties. Future advancements in AM-CM technology aim to enhance process efficiency, broaden material versatility, and improve part performance. This involves exploring novel materials, advancing process monitoring, implementing automation technologies, and integrating artificial intelligence (AI) and machine learning (ML) for predictive modeling and real-time optimization in composite manufacturing. These developments will establish the AM-CM system as a transformative technology in composite manufacturing, driving innovation across industries.

Hassen, Ahmed [ORNL] (ORCID:0000000328521222)↗
DOE OSTI2026

Physics-informed machine learning exploration of Na storage mechanisms in disordered carbon

Sodium-ion batteries are a cost-effective, sustainable alternative to lithium-ion systems for large-scale energy storage. However, optimizing sodium storage in carbon-based anodes with microstructural complexity and atomic disorder remains a major challenge. The intrinsic inhomogeneity of these materials produces diverse local environments, making it difficult for conventional methods to predict and control ion dynamics. Hard carbon (HC) anodes, composed of ranges of ordered-to-disordered graphitic and amorphous nanodomains, offer tunable ion storage and rate capacity, yet rationale design remains a challenge due to poorly understood correlation between local atomic feature and ion transport mechanism. Here, to address this challenge, we introduce a data-driven framework that integrates validated machine-learned interatomic potentials, large-scale molecular dynamics simulations, and machine learning to elucidate sodium transport mechanisms as a function of carbon and sodium loading densities. By computing per-ion structural descriptors and applying unsupervised learning, we identify distinct diffusion modes governed by microscopic features. Supervised analysis and correlation mapping then establish quantitative links between these transport regimes and processing variables such as bulk carbon density and sodium content. This physics-informed approach establishes quantitative structure–transport relationships and offers actionable design principles for engineering high-performance HC anodes.

Data-driven framework↗
DOE OSTI2020

Tunable structural color of bottlebrush block copolymers through direct-write 3D printing from solution

Additive manufacturing of functional materials is limited by control of microstructure and assembly at the nanoscale. In this work, we integrate nonequilibrium self-assembly with direct-write three-dimensional (3D) printing to prepare bottlebrush block copolymer (BBCP) photonic crystals (PCs) with tunable structure color. After varying deposition conditions during printing of a single ink solution, peak reflected wavelength for BBCP PCs span a range of 403 to 626 nm (blue to red), corresponding to an estimated change in d-spacing of >70 nm (Bragg- Snell equation). Physical characterization confirms that these vivid optical effects are underpinned by tuning of lamellar domain spacing, which we attribute to modulation of polymer conformation. Using in situ optical microscopy and solvent-vapor annealing, we identify kinetic trapping of metastable microstructures during printing as the mechanism for domain size control. More generally, we present a robust processing scheme with potential for on-the-fly property tuning of a variety of functional materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A Constitutive Structural Parameter for the Work Hardening Behavior of Additively Manufactured Ti-6Al-4V

The mechanical behavior of Ti-6Al-4V produced by additive manufacturing processes is assessed based on a formulation developed from the Kocks-Mecking relationship. A constitutive parameter derived for the microstructure is characteristic of the work hardening behavior determined by the plastic strain between the proportional limit and the strength at the instability point. The varied plasticity behavior associated with surface and build direction effects can be evaluated with this approach as presented for the case of Ti-6Al-4V under uniaxial tension.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Abradable Sealing Materials for Emerging IGCC-Based Turbine Systems (Final Report)

Reducing the gap between rotating and stationary parts in gas turbine engines, and mitigating gas leakage via these paths, can significantly increase the performance and attendant efficiency. One approach to reducing such gaps is to deploy abradable coatings on the stationary shroud components as seals, to reduce the blade-tip clearances under operational conditions. Abradable coatings must be able to withstand high temperature oxidation, thermal cycling, and erosion, while providing optimal controlled abrasion and associated shape retention. Existing abradable seals utilized in power generation turbines have generally been optimized for use with natural gas-fired systems; however, preliminary testing of syngas and high-hydrogen-content (HHC) fired turbines has shown that the stability of hot-section materials (and presumably abradable sealing materials) may be substantially altered due to characteristic changes in the combustion by-products (partial pressures of water vapor, etc.) as well as characteristic impurities and particulate matter entrained in the fuel. The primary focus of this research program has been to develop a mechanistic understanding of how the altered combustion environments modify the thermo-mechanical stability and performance of the sealing materials, including the requisite abradable sealing behavior. A key component of the research program carried out has been an exploration of mechanisms underpinning observed degradation processes, and an assessment of connections to the combustion environments and characteristic non-combustible constituents. The ultimate goal of the project has been to advance the goals of the Advanced Turbine Program by developing materials design protocols leading to turbine hot-section components with improved resistance to service lifetime degradation under advanced fuels exposures. This research program has evaluated the performance and degradation of ceramic abradable seals used in the high-temperature turbine sections of gas turbine engines. The focus has been two-fold: (1) to understand performance of such materials in relation to the turbines operating on coal-derived syngas and high hydrogen content (HHC) fuels, ultimately seeking an improved understanding of factors that control performance and durability of abradable seal materials for these combustion environments (and play into materials design protocols); and (2) to evaluate the potential of alternative materials as abradable seals for the higher temperatures expected with IGCC and HHC fueled turbine systems. In particular, we carried out an initial assessment of multi-layered systems of existing abradable seal materials (YSZ) and other ceramics. The research program also investigated several classes of abradable coatings under simulated exposures to syngas-based combustion environments, evaluating the relevant wear behavior, hardness, stability under cyclic oxidation, and general thermo-mechanical behavior. The research also attempted to develop alternatives to carrying out full-scale combustion-based abradability test rig exposures to evaluate materials system performance. The research has been focused on correlating the measured thermo-mechanical behavior, and controlled abrasive wear, with the intrinsic properties of the multilayer coatings and processing-controlled microstructural features that have shown attractive machinability characteristics based on weak interfacial bonding between the constituent phases at elevate temperatures (while maintaining thermochemical stability). This program has resulted in an improved mechanistic understanding of factors governing performance of high temperature abradable seals, and degradation mechanisms unique to IGCC-based power generation turbine systems and the realization of coal-derived syngas and HHC-based combustion environments – ultimately with the goal of developing a knowledge base upon which the design of coatings that retain optimal sealing characteristics and are more resistant to the observed wear/attack mechanisms, important aspects of advancing the goals of the DOE Advanced Turbine Program.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Processing and mechanical characterization of short carbon fiber-reinforced epoxy composites for material extrusion additive manufacturing

Fiber-reinforced polymer composites have been extensively utilized in recent years as feedstock materials for material extrusion additive manufacturing (AM) processes to improve strength, stiffness, and functionality of printed parts over unfilled printed polymers. However, the widespread adoption of AM of fiber-reinforced polymer composites requires a deeper understanding of the process-structure-property relationships in printed components, and such relationships are not well understood yet. Fiber length is critically important to the mechanical performance of short fiber composites, but very few studies to-date have focused on how the fiber length distribution (FLD) evolves during processing of composite feedstocks and how this evolution affects printing behavior and mechanical properties in 3D-printed composites. Here, FLD is measured for carbon fiber reinforced epoxy composites over a wide range of ink compositions and shear mixing times, and the distributions are fit with a Weibull-type distribution function. The effects of FLD on the tradeoff between ink processability, ink rheology, printing behavior and mechanical properties are investigated. Furthermore, the effects of printing parameters (nozzle size and print speed) on mechanical anisotropy and fiber orientation distribution (FOD) in printed composites are explored. Mechanical properties of printed composites are characterized via 3 pt-flexural testing, and microstructure is investigated using optical and scanning electron microscopy (SEM), and x-ray computed tomography. Finally, the fitted Weibull parameters are fed into a composite model that incorporates FLD and FOD, and model predictions are found to be in excellent agreement with experimental observations.

3D printing↗
DOE OSTI2021

Internal Microstructure Dictates Interactions of Polymer-grafted Nanoparticles in Solution

Understanding the effects of polymer brush architecture on particle interactions in solution is requisite to enable the development of functional materials based on self-assembled polymer-grafted nanoparticles (GNPs). Static and dynamic light scattering of polystyrene-grafted silica particle solutions in toluene reveals that the pair interaction potential, inferred from the second virial coefficient, A 2 , is strongly affected by the grafting density, σ, and degree of polymerization, N, of tethered chains. In the limit of intermediate σ (~0.3 to 0.6 nm -2 ) and high N, A 2 is positive and increases with N. This confirms the good solvent conditions and can be qualitatively rationalized on the basis of a pair interaction potential derived for grafted (brush) particles. In contrast, for high σ > 0.6 nm -2 and low N, A 2 displays an unexpected reversal to negative values, thus indicating poor solvent conditions. These findings are rationalized by means of a simple analysis based on a coarse-grained brush potential, which balances the attractive core-core interactions and the excluded volume interactions imparted by the polymer grafts. The results suggest that the steric crowding of polymer ligands in dense GNP systems may fundamentally alter the interactions between brush particles in solution and highlight the crucial role of architecture (internal microstructure) on the behavior of hybrid materials. The effect of grafting density also illustrates the opportunity to tailor the physical properties of hybrid materials by altering geometry (or architecture) rather than a variation of the chemical composition.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High Temperature Thermal Barrier Coating Evaluation of Yttrium Aluminum Garnet for Gas Turbine Applications

The Solution Precursor Spray Process (SPPS) process has been shown to overcome the durability and property challenges of applying yttrium aluminum garnet (YAG) coating for high temperature thermal barrier coating (TBC) applications (1200°C+) but only limited testing has been performed in representative application environments. In this study, YAG coatings were developed to optimize microstructure and tailor properties for combustion components in an industrial gas turbine. Thermal conductivity, erosion resistance and furnace cycling durability were used to validate YAG properties against the standard yttria-stabilized zirconia coating (YSZ). Graded and multi-layered microstructures were applied to enhance performance while maintaining durability. Further YAG process development was required to replicate coating properties and optimize deposition on more complex fuel injector nozzle and combustion liner components. Rig testing of both components was performed and compared against the baseline YSZ coating validating the high temperature capability and lower thermal conductivity of the SPPS YAG coating. The components in both tests were cycled for a minimum of ten cycles with the fuel injector test targeting a higher operating temperature while the combustor liner operated at standard conditions. A development engine test is planned to further validate performance in a gas turbine engine of this promising material.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Additive Friction Stir Deposition of a Tantalum–Tungsten Refractory Alloy

Additive friction stir deposition (AFSD) is a solid-state metal additive manufacturing technique, which utilizes frictional heating and plastic deformation to create large deposits and parts. Much like its cousin processes, friction stir welding and friction stir processing, AFSD has seen the most compatibility and use with lower-temperature metals, such as aluminum; however, there is growing interest in higher-temperature materials, such as titanium and steel alloys. In this work, we explore the deposition of an ultrahigh-temperature refractory material, specifically, a tantalum–tungsten (TaW) alloy. The solid-state nature of AFSD means refractory process temperatures are significantly lower than those for melt-based additive manufacturing techniques; however, they still pose difficult challenges, especially in regards to AFSD tooling. In this study, we perform initial deposition trials of TaW using twin-rod-style AFSD with a high-temperature tungsten–rhenium-based tool. Many challenges arise because of the high temperatures of the process and high mechanical demand on AFSD machine hardware to process the strong refractory alloy. Despite these challenges, successful deposits of the material were produced and characterized. Mechanical testing of the deposited material shows improved yield strength over that of the annealed reference material, and this strengthening is mostly attributed to the refined recrystallized microstructure typical of AFSD. These findings highlight the opportunities and challenges associated with ultrahigh-temperature AFSD, as well as provide some of the first published insights into twin-rod-style AFSD process behaviors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

All-Ceramic Passive Wireless Temperature Sensor Realized by Tin-Doped Indium Oxide (ITO) Electrodes for Harsh Environment Applications

In this work, an all-ceramic passive wireless inductor–capacitor (LC) resonator was presented for stable temperature sensing up to 1200 °C in air. Instead of using conventional metallic electrodes, the LC resonators are modeled and fabricated with thermally stable and highly electroconductive ceramic oxide. The LC resonator was modeled in ANSYS HFSS to operate in a low-frequency region (50 MHz) within 50 × 50 mm geometry using the actual material properties of the circuit elements. The LC resonator was composed of a parallel plate capacitor coupled with a planar inductor deposited on an Al2O3 substrate using screen-printing, and the ceramic pattern was sintered at 1250 °C for 4 h in an ambient atmosphere. The sensitivity (average change in resonant frequency with respect to temperature) from 200–1200 °C was ~170 kHz/°C. The temperature-dependent electrical conductivity of the tin-doped indium oxide (ITO, 10% SnO2 doping) on the quality factor showed an increase of Qf from 36 to 43 between 200 °C and 1200 °C. The proposed ITO electrodes displayed improved sensitivity and quality factor at elevated temperatures, proving them to be an excellent candidate for temperature sensing in harsh environments. The microstructural analysis of the co-sintered LC resonator was performed using a scanning electron microscope (SEM) which showed that there are no cross-sectional and topographical defects after several thermal treatments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Additive Manufacturing of Poly(phenylene Sulfide) Aerogels via Simultaneous Material Extrusion and Thermally Induced Phase Separation

Abstract Additive manufacturing (AM) of aerogels increases the achievable geometric complexity, and affords fabrication of hierarchically porous structures. In this work, a custom heated material extrusion (MEX) device prints aerogels of poly(phenylene sulfide) (PPS), an engineering thermoplastic, via in situ thermally induced phase separation (TIPS). First, pre‐prepared solid gel inks are dissolved at high temperatures in the heated extruder barrel to form a homogeneous polymer solution. Solutions are then extruded onto a room‐temperature substrate, where printed roads maintain their bead shape and rapidly solidify via TIPS, thus enabling layer‐wise MEX AM. Printed gels are converted to aerogels via postprocessing solvent exchange and freeze‐drying. This work explores the effect of ink composition on printed aerogel morphology and thermomechanical properties. Scanning electron microscopy micrographs reveal complex hierarchical microstructures that are compositionally dependent. Printed aerogels demonstrate tailorable porosities (50.0–74.8%) and densities (0.345–0.684 g cm −3 ), which align well with cast aerogel analogs. Differential scanning calorimetry thermograms indicate printed aerogels are highly crystalline (≈43%), suggesting that printing does not inhibit the solidification process occurring during TIPS (polymer crystallization). Uniaxial compression testing reveals that compositionally dependent microstructure governs aerogel mechanical behavior, with compressive moduli ranging from 33.0 to 106.5 MPa.

Chemistry↗
DOE OSTI2021

Development of High-Performance Ni-base Alloys for Gas Turbine Wheels Using a Coprecipitation Approach (Final Technical Report)

In this project, a synergistic approach involving experiments informed by modelling was used to develop γ'/γ'' coprecipitation-strengthened Ni-base superalloys for land-based gas turbine wheels. In thick sections of such turbine wheels, the slow cooling rate normally observed, as well as variations in cooling rate could potentially result in drastically inhomogeneous and coarsened microstructure. Thus, ten alloy compositions were selected based on coprecipitation and sluggish γ’ growth and coarsening during three iterations of alloy development, assisted by extensive CALPHAD modeling. Phase equilibrium calculations, informed by the characterization of early alloys, were successful in predicting suitable aging treatments to obtain bimodal coprecipitate distribution in several alloys. These aging treatments were applied to the subsequent round of alloys and the resulting microstructures were characterized in detail. Two different cooling rates were used during each of these heat treatments to simulate the range of cooling rates observed in a thick section forging. The microstructures were used to calibrate a multi-phase field model (MPF), which was used to study the formation mechanisms of various coprecipitate morphologies observed in the experiments. Following this, the most promising alloys in each round were selected and studied using high temperature tensile and creep tests. Considering that a slower cooling rate would lead to a strength debit, while a faster cooling rate might lead to a decline in creep rupture life of a full-scale wheel, tensile tests were carried out for slower cooled samples, while creep tests were carried out for faster cooled samples. The deformation microstructures were then characterized using advanced characterization techniques such as Diffraction Contrast-Scanning Transmission Electron Microscopy (DC-STEM) and Electron Channeling Contrast Imaging (ECCI). Further, a mean-field creep model was developed and calibrated using these experimental findings to predict long-term creep behavior of these coprecipitation-strengthened alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural Characterization of the Second High Fluence Baffle-Former Bolt Retrieved from a Westinghouse Two-loop Downflow Type PWR

As one of the pressurized water reactor (PWR) internal components, baffle-former bolts (BFBs) are subjected to significant mechanical stress and neutron irradiation from the reactor core during the plant operation. Over the long operation period, these conditions lead to potential degradation and reduced load-carrying capacity of the bolts. In support of evaluating long-term operational performance of materials used in core internal components, the Oak Ridge National Laboratory (ORNL), through the Department of Energy (DOE), Light Water Reactor Sustainability (LWRS) Program, Materials Research Pathway (MRP) has harvested two high fluence BFBs from a commercial Westinghouse two-loop downflow type PWR. The two bolts of interest, i.e. bolts # 4412 and 4416, were withdrawn from service in 2011 as part of a preventative replacement plan. No identification of cracking or potential damage was found for these bolts during their removal in 2011. However, the bolts required a lower torque for removal from the baffle structure than the original torque specified during installation. Irradiation displacement damage levels in the bolts range from 15 to 41 displacements per atom. The goal of this project is to perform detailed microstructural and mechanical property characterization of BFBs following in-service exposures. The information from these bolts will be integral to the LWRS program initiatives in evaluating end of life microstructure and properties. Furthermore, valuable data will be obtained that can be incorporated into model predictions of long-term irradiation behavior and compared to results obtained in high flux experimental reactor conditions. In this report, we present our latest study in FY22 on microstructural characterizations of the second high fluence baffle-former bolt, i.e., bolt # 4412. Analytical electron microscopy and atom probe tomography characterization were performed. The radiation-induced defects in the material add to the large wealth of knowledge for neutron-induced defects in 304/316 grades of stainless steels, specifically for radiation-induced precipitation after high fluence commercial PWR irradiation. The main findings are summarized as follows: 1) The cavity size was considerably larger in the bolt thread section than in the bolt head, with the bolt thread section having a bimodal distribution of cavities greater than ~6 nm in diameter and less than ~3 nm in diameter. The bolt head only had the small-sized cavities. In addition, there was a denuded zone of large cavities near grain boundaries in the thread section of the bolt. 2) Radiation-induced precipitation in the BFB #4412 was highly complex, with the volume fraction, size, and number density of Ni/Si and Cu-rich precipitates depending strongly on the radiation temperature/dose. In many cases, co-precipitates of adjoined clusters were found with Ni/Si-rich precipitates sandwiched between Cu-rich clusters and Mo/Cr/P-rich clusters. 3) Solute segregation out of solution was highest for most solutes in the thread section of the bolt #4412 with the exception of Cu, which experienced more separation out of solution into Curich clusters in the bolt head section. This highlights the difference in the mechanisms for precipitation of Ni/Si clusters, which have the Ni 3 Si phase composition, and precipitation of Cu-rich clusters. 4) There appear to be multiple simultaneous influences that affect the microstructural variation along the length of the bolt that overcomes the ~2X difference in irradiation dose between the bolt head and the bolt thread. The irradiation temperature, thermal/fast neutron ratio variation, potential strain gradient, and exposure to PWR coolant water that each section of the bolt sees may have more influence on the microstructural evolution than the total irradiation dose. The bolt thread and shank, with higher temperature, higher relative fast neutron flux, higher strain, and exposure to coolant but lower dose, underwent more enhanced cavity formation, precipitation, and solute segregation than the bolt head section.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2019

Slurry rheology of Hanford sludge

Here we evaluate the slurry viscosity of radioactive waste. Hanford waste is a motely mixture of particle sizes and densities composed of metal and oxide particles with constituents spanning much of the periodic table stored at high ionic strength and high pH. Hanford wastes have traditionally been represented as simply an ideal Bingham plastic, but this rheological approximation often provides a poor fit from 0 to 200 1/s, precisely the range of interest for engineering design of waste transport and mixing systems. Here we use a modified Cross formulation inclusive of a yield stress to fit stress-strain rate data for reconstituted Hanford REDOX sludge waste, measured by increasing shear-rate (up-ramp) and decreasing shear-rate (down-ramp) sweeps. We find that this continuous single equation formulation quantitatively matches experimental data better than other rheological models including the Bingham plastic and Herschel-Bulkley approximations. The increase of viscosity and yield stress from up ramp to down ramp indicates the formation of particle microstructure during shear due to attractive forces.

radioactive waste, high ionic strength slurries, y↗
DOE OSTI2024

Sulphate resistance of low‐clinker engineered cementitious composites examined by MicroXRF imaging

Abstract Engineered cementitious composites (ECC) are a class of high‐performing fibre‐reinforced cementitious materials recognised for their increased ductility and durability compared to conventional cement‐based materials, owing to their autogenously controlled tight crack widths, even when subjected to high strains. To reduce ECC's environmental impact, this research examines the use of a low‐clinker binder − limestone‐calcined clay cement (LC3) − as an alternative to portland cement (PC), along with fly ash to further reduce the clinker proportion and the embodied CO 2 of the formulations. In conventional concrete, LC3 hydrates to a denser microstructure resulting from the synergistic reaction between limestone and calcined clay. At the lower water contents typical of ECC and with the presence of fly ash, the influence of the binder composition on the microstructure is difficult to anticipate. To examine the influence of these compositional variables on microstructure, permeability and durability, the sulphate resistance of LC3‐based ECC is explored. Specifically, the ECC‐LC3 blends are designed with high clinker replacement rate of 75% by mass of binder and contain either conventional fly ash or reclaimed fly ash at 50% by mass of binder. Expansion of ECC‐LC3 samples subjected to standard sodium sulphate test conditions was measured up to 12 months and the depth of penetration of sulphates into the ECC‐LC3 of varying compositions was quantified using micro‐X‐Ray Fluorescence (microXRF) imaging and modelling. The expansion results show that the ECC‐LC3 formulations performed better than the PC samples and can provide adequate resistance to external sulphate attack, even when reclaimed fly ashes are used in place of the conventional ash. In addition, the shallow penetration of sulphate into these cementitious composites demonstrates the low diffusion coefficients values that were determined using the quantitative data from MicroXRF imaging.

Microscopy↗