Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Materials engineering tetrahedron economic evaluation tool

A new open-source project evaluation tool, entitle the Materials Engineering Tetrahedron (MET), has been developed to determine the economic viability of materials design, selection, processing, and validation costs associated with any infrastructure-based project. MET improves project design by providing an economic perspective to the traditional materials science tetrahedron, relating microstructure, processing, property, and performance through the introduction of value-based economic costs for each side of the tetrahedron. The resulting size and distortion, from a regular tetrahedron illustrates the balance between the system, component, or material fabrication project detailed. Furthermore, the MET model also allows for increased budget efficiency and the potential for improved identification of cost saving mechanisms.

36 MATERIALS SCIENCE↗

Low Thermal Conductivity, High Durability Thermal Barrier Coatings for IGCC Environments

Advanced thermal barrier coatings (TBC) are crucial to improved energy efficiency in next generation gas turbine engines. The use of traditional topcoat materials, e.g. yttria-stabilized zirconia (YSZ), is limited at elevated temperatures due to (1) the accelerated undesirable phase transformations and (2) corrosive attacks by calcium-magnesium-aluminum-silicate (CMAS) deposits and moisture. The first goal of this project is to use the Solution Precursor Plasma Spray (SPPS) process to further reduce the thermal conductivity of YSZ TBCs by introducing a unique microstructural feature of layered porosity, called inter-pass boundaries (IPBs). Extensive process optimization accompanied with hundreds of spray trials as well as associated SEM cross-section and laser-flash measurements, yielded a thermal conductivity as low as 0.62 Wm⁻¹K⁻¹ in SPPS YSZ TBCs, approximately 50% reduction of APS TBCs; while other engine critical properties, such as cyclic durability, erosion resistance and sintering resistance, were characterized to be equivalent or better than APS baselines. In addition, modifications were introduced to SPPS TBCs so as to enhance their resistance to CMAS under harsh IGCC environments. Several mitigation approaches were explored, including doping the coatings with Al₂O₃ and TiO₂, applying a CMAS infiltration-inhibiting surface layer, and filling topcoat cracks with blocking substances. The efficacy of all these modifications was assessed with a set of novel CMAS-TBC interaction tests, and the moisture resistance was tested in a custom-built high-temperature moisture rig. In the end, the optimal low thermal conductivity TBC system was selected based on all evaluation tests and its processing conditions were documented. The optimal coating consisted on a thick inner layer of YSZ coating made by the SPPS process having a thermal conductivity 50% lower than standard YSZ coatings topped with a high temperature tolerant CMAS resistant gadolinium zirconate Coating made by the SPPS process. Noteworthy was the fact that the YSZ to GZO interface made by the SPPS process was not the failure location as had been observed in APS coatings.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Rotary Inertia Friction Welding of Dissimilar High-Strength 422 Martensitic Stainless Steel and 4140 Low Alloy Steel for Heavy-Duty Engine Piston Fabrication

AISI 422 martensitic stainless steel with superior high temperature performance (oxidation resistance and strength) is under evaluation for replacing current heavy-duty piston crown materials, AISI 4140 martensitic steel and micro alloyed steel (MAS) 38MnSiVS5, to fabricate a multimaterial piston. This multimaterial piston concept further improved power density and fuel economy by allowing heavyduty diesel engines to operate at higher temperatures and pressures. Joining AISI 422 steel piston crowns with AISI 4140 steel piston skirts is a key manufacturing step for this multimaterial piston. However, the significant differences in strength, elevated temperature flow stress, alloy chemistry, and temper resistance between these two martensitic steels cause some weldability issues (cracking) and metallurgical challenges (alloying element migration/segregation) when using conventional fusion-based welding processes. Rotary inertia friction welding (RIFW), a solid-state welding process, has been the preferred method to join 4140 crowns to 4140 skirts (and MAS crowns to MAS skirts) in high-volume production of current heavy-duty diesel engine pistons. It has been used to join these two materials with relatively comparable alloy chemistry to fabricate pistons with MAS skirts and 4140 crowns. Meanwhile, RIFW has also been a preferred method of dissimilar metal welding. However, RIFW of dissimilar high-strength martensitic steels has yet to be widely pursued. The interfacial microstructure complexities created by the thermomechanical process and highly nonequilibrium phase transformations during RIFW are a significant challenge for understanding and predicting their joining behavior and have not been reported in detail. Here, in this work, defect-free AISI 422 steel-AISI 4140 multimaterial pistons were successfully fabricated using the RIFW process. The interfacial microstructure and mechanical properties of dissimilar 422/4140 steel RIFW in the as-welded condition were experimentally studied in detail. The results provide critical baseline information for understanding RIFW mechanisms and guiding subsequent postweld heat treatment (PWHT) practice.

36 MATERIALS SCIENCE↗

High Speed In-situ X-ray Imaging of 3D Freeze Printing of Aerogels

3D freeze printing (3DFP) combines drop-on-demand (DOD) inkjet printing with freeze casting to fabricate lightweight and multifunctional aerogels with customized geometries. Freeze casting is an efficient and easily implemented method capable of fabricating porous, sponge-like structures for many different applications. This process enables tailoring the microstructure of the final product (i.e., pore morphology, alignment, average size distribution, etc.) by controlling the fabrication conditions and freezing kinetics. Furthermore, its combination with DOD printing provides the capability of engineering the macrostructure without relying on a mold as reported for 3D freeze-printed aerogels made from graphene, silver nanowires, and other nanocomposites. In this paper, we performed in-situ X-ray imaging to understand the inside process dynamics in 3DFP using a commercially available colloidal silica ink. We investigated the 3DFP process with the following hierarchy: first, single droplets; then, uniform lines obtained from coalescence of droplets; and finally, three consecutive lines deposited layer by layer. With the help of X-ray imaging, the importance of the balance between material deposition and freezing rates was shown in-situ by the observation inside of the freeze front following the tip of the printed line. The effects of the substrate temperature on the elimination of undesired interfacial boundaries were also shown by the observed ice crystals penetrating from lower to upper layer.

36 MATERIALS SCIENCE↗

Designing and transforming yield-stress fluids

We review progress in designing and transforming multi-functional yield-stress fluids and give a perspective on the current state of knowledge that supports each step in the design process. We focus mainly on the rheological properties that make yield-stress fluids so useful and the trade-offs which need to be considered when working with these materials. Thinking in terms of "design with" and "design of' yield-stress fluids motivates how we can organize our scientific understanding of this field. "Design with" involves identification of rheological property requirements independent of the chemical formulation, e.g. for 3D direct-write printing which needs to accommodate a wide range of chemistry and material structures. "Design of includes microstructural considerations: conceptual models relating formulation to properties, quantitative models of formulation-structureproperty relations, and chemical transformation strategies for converting effective yield-stress fluids to be more useful solid engineering materials. Finally, future research directions are suggested at the intersection of chemistry, soft-matter physics, and material science in the context of our desire to design useful Theologically-complex functional materials.

36 MATERIALS SCIENCE↗

Quench process modeling & simulation in the heat-treatment of critical aerospace components

To manufacture light-weight, advanced metal alloy components for gas turbine engines, quench heat-treatment processes are typically used. By quenching the component from elevated tempera-tures, the alloy sometimes undergoes a solid-state phase transformation which produces special microstructures with the required, enhanced mechanical properties. However, the quenching can also lead to cracks forming in the component. Addressing the quench cracking problems adds a significant burden to the cost, schedule, and energy demand of manufacture. Currently, optimizing the quench process to mitigate or avoid the cracking is performed largely by trial-and-error, relying heavily on costly experimental (thermocouple) trials to understand the local thermal gradients which cause the cracks to form. In this first part (Phase 1) of the work, high-performance computing is employed to establish the ability of modern CFD (computational fluid dynamics) to alleviate or wholly replace the experimental quenching trials by virtual testing. A baseline CFD model is defined and its accuracy established to be comparable to (and which usually exceeds) the accuracy of existing HTC (heat-transfer correlation) based simulation methods of quenching. As a first-principles based approach, “calibration” of the Baseline CFD model is independent of the quench process itself, but instead relies on the accuracy of the underlying (modeled), generic two-phase fluid processes which cannot be currently resolved by CFD for large, industrial-scale cases. A novel, high-fidelity DNS capability has been developed and verified to examine and further improve upon the mean-field closure submodels on which the Baseline CFD approach is based.

36 MATERIALS SCIENCE↗

Overview of zirconia with respect to gas turbine applications

Phase relationships and the mechanical properties of zirconia are examined as well as the thermal conductivity, deformation, diffusion, and chemical reactivity of this refractory material. Observations from the literature particular to plasma-sprayed material and implications for gas turbine engine applications are discussed. The literature review indicates that Mg-PSZ (partially stabilized zirconia) and Ca-PSZ are unsuitable for advanced gas turbine applications; a thorough characterization of the microstructure of plasma-sprayed zirconia is needed. Transformation-toughened zirconia may be suitable for use in monolithic components.

Cawley, J. D.↗

High-Frequency Focused Water-Coupled Ultrasound Used for Three-Dimensional Surface Depression Profiling

To interface with other solids, many surfaces are engineered via methods such as plating, coating, and machining to produce a functional surface ensuring successful end products. In addition, subsurface properties such as hardness, residual stress, deformation, chemical composition, and microstructure are often linked to surface characteristics. Surface topography, therefore, contains the signatures of the surface and possibly links to volumetric properties, and as a result serves as a vital link between surface design, manufacturing, and performance. Hence, surface topography can be used to diagnose, monitor, and control fabrication methods. At the NASA Glenn Research Center, the measurement of surface topography is important in developing high-temperature structural materials and for profiling the surface changes of materials during microgravity combustion experiments. A prior study demonstrated that focused air-coupled ultrasound at 1 MHz could profile surfaces with a 25-m depth resolution and a 400-m lateral resolution over a 1.4-mm depth range. In this work, we address the question of whether higher frequency focused water-coupled ultrasound can improve on these specifications. To this end, we employed 10- and 25-MHz focused ultrasonic transducers in the water-coupled mode. The surface profile results seen in this investigation for 25-MHz water-coupled ultrasound, in comparison to those for 1-MHz air-coupled ultrasound, represent an 8 times improvement in depth resolution (3 vs. 25 m seen in practice), an improvement of at least 2 times in lateral resolution (180 vs. 400 m calculated and observed in practice), and an improvement in vertical depth range of 4 times (calculated).

Roth, Don J.↗

Processing of Nanostructured Ferritic Alloys for Advanced Reactor Core Materials

The Fuel Cycle Research and Development Program is investigating methods of burning minor actinides in a transmutation fuel. To achieve this goal, the fast reactor core materials (cladding and duct) must be able to withstand very high doses (>200 dpa design goal) while in contact with the coolant and the fuel. Thus, these materials must withstand radiation effects that promote low temperature embrittlement, high temperature helium embrittlement, swelling, accelerated creep, corrosion with the coolant, and chemical interaction with the fuel (FCCI). One of the most promising materials for this demanding applications are the class of nanostructured ferritic alloys. These materials are ferritic alloys with high chrome (9-14Cr) with a high density (>10{sup 23}/m{sup 3}), fine distribution of nanosized (∼2 nm) oxide particles and a fine grain size (<0.5 micron). This fine microstructure provides an alloy with high strength at high temperatures and excellent radiation tolerance (e.g. reduced void swelling and ductility retention at low temperatures) but also increases the difficulty of producing engineering parts (e.g. thin walled tubes) from these advanced materials. Thus, extensive research is underway to produce tubes using techniques such as high temperature hydrostatic extrusion, intermediate temperature plug drawing and low temperature pilger processing. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A Quantitative Phase Analysis by Neutron Diffraction of Conventional and Advanced Aluminum Alloys Thermally Conditioned for Elevated-Temperature Applications

As the issue of climate change becomes more prevalent, engineers have focused on developing lightweight Al alloys capable of increasing the power density of powertrains. The characterization of these alloys has been focused on mechanical properties and less on the fundamental response of microstructures to achieve these properties. Therefore, this study assesses the quality of the microstructure of two high-temperature Al alloys (A356 + 3.5RE and Al-8Ce-10Mg), comparing them to T6 A356. These alloys underwent thermal conditioning at 250 and 300 °C for 200 h. Time-of-flight neutron diffraction experiments were performed before and after conditioning. The phase evolution was quantified using Rietveld refinement. It was found that the Si phase grows significantly (13–24%) in T6 A356, A356 + 3.5RE, and T6 A356 + 3.5RE alloys, which is typically correlated with a reduction in mechanical properties. Subjecting the A356 3.5RE alloy to a T6 heat treatment stabilizes the orthorhombic Al4Ce3Si6 and monoclinic β-Al5FeSi phases, making them resistant to thermal conditioning. These two phases are known for enhancing mechanical properties. Additionally, the T6 treatment reduced the vol.% of the cubic Al20CeTi2 and hexagonal ᴨ-Al9FeSi3Mg5 phases by 13% and 23%, respectively. These phases have detrimental mechanical properties. The Al-8Ce-10Mg alloy cubic β-Al3Mg2 phase showed significant growth (82–101%) in response to conditioning, while the orthorhombic Al11Ce3 phase remained stable. The growth of the beta phase is known to decrease the mechanical properties of this alloy. These efforts give valuable insight into how these alloys will perform and evolve in demanding high-temperature environments.

Chemistry↗

Process Integration and Optimization of ICME Carbon Fiber Composites for Vehicle Lightweighting: A Preliminary Development

Process integration and optimization is the key enabler of the Integrated Computational Materials Engineering (ICME) of carbon fiber composites. In this paper, automated workflows are developed for two types of composites: Sheet Molding Compounds (SMC) short fiber composites, and multi-layer unidirectional (UD) composites. For SMC, the proposed workflow integrates material processing simulation, microstructure representation volume element (RVE) models, material property prediction and structure preformation simulation to enable multiscale, multidisciplinary analysis and design. Processing parameters, microstructure parameters and vehicle subframe geometry parameters are defined as the design variables; the stiffness and weight of the structure are defined as the responses. For multi-layer UD structure, this work focuses on the discussion of different design representation methods and their impacts on the optimization performance. Challenges in ICME process integration and optimization are also summarized and highlighted. Two case studies are conducted to demonstrate the integrated process and its application in optimization.

36 MATERIALS SCIENCE↗

Photoactive Blend Morphology Engineering through Systematically Tuning Aggregation in All-Polymer Solar Cells

Polymer aggregation plays a critical role in the miscibility of materials and the performance of all-polymer solar cells (APSCs). However, many aspects of how polymer texturing and aggregation affect photoactive blend film microstructure and photovoltaic performance are poorly understood. Here the effects of aggregation in donor–acceptor blends are studied, in which the number-average molecular weights (Mns) of both an amorphous donor polymer, poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b;4,5-b]dithiophene-2,6-diyl-alt-(4-(2-ethylhexyl)-3-fluorothieno[3,4-b]thiophene-)-2-carboxylate-2-6-diyl)] (PBDTT-FTTE) and a semicrystalline acceptor polymer, poly{[N,N'-bis(2-octyldodecyl)naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5'-(2,2'-bithiophene)} (P(NDI2OD-T2)) are systematically varied. The photovoltaic performance is correlated with active layer microstructural and optoelectronic data acquired by in-depth transmission electron microscopy, grazing incidence wide-angle X-ray scattering, thermal analysis, and optical spectroscopic measurements. Coarse-grained modeling provides insight into the effects of polymer aggregation on the blend morphology. Notably, the computed average distance between the donor and the acceptor polymers correlates well with solar cell photovoltaic metrics such as short-circuit current density (Jsc) and represents a useful index for understanding/predicting active layer blend material intermixing trends. Importantly, these results demonstrate that for polymers with different texturing tendencies (amorphous/semicrystalline), the key for optimal APSC performance, photovoltaic blend morphology can be controlled via both donor and acceptor polymer aggregation.

bio-inspired↗

A fully coupled thermal–microstructural–mechanical finite element process model for directed energy deposition additive manufacturing of Ti–6Al–4V

A fully coupled thermal–microstructural–mechanical finite element modelling framework is developed to investigate the distortion and residual stresses during directed energy deposition (DED) of multi-phase Ti–6Al–4V alloy. The Johnson–Cook constitutive model is used to predict the yield strength of each phase as a function of strain, strain rate and temperature where the flow stress is calculated by a linear mixing rule based on the volumetric phase fractions. A thin-walled rectangular sample is chosen as the reference geometry and the results are compared with experimentally measured in situ thermal history and distortion data, where a reasonable agreement is achieved. The proposed modelling framework with physics-based material constitutive model provides useful information for a better understanding of process–microstructure–property relations in additive manufacturing by DED.

Tunay, Merve↗

Holographic optical assembly and photopolymerized joining of planar microspheres

The aim of this research is to demonstrate a holographically driven photopolymerization process for joining colloidal particles to create planar microstructures fixed to a substrate, which can be monitored with real-time measurement. Holographic optical tweezers (HOT) have been used to arrange arrays of microparticles prior to this work; here we introduce a new photopolymerization process for rapidly joining simultaneously handled microspheres in a plane. Additionally, we demonstrate a new process control technique for efficiently identifying when particles have been successfully joined by measuring a sufficient reduction in the particles’ Brownian motion. Furthermore, this technique and our demonstrated joining approach enable HOT technology to take critical steps toward automated additive fabrication of microstructures.

36 MATERIALS SCIENCE↗

Metallurgical aspects influencing the resistance to steam oxidation and fracture toughness of select advanced replacement alloys for LWR core internals

Life extension of the existing nuclear reactors imposes accumulated damages, such as higher fluences and longer period of corrosion, to structural materials, which would result in significant challenges to the traditional reactor materials such as type 304 and 316 stainless steels. Advanced alloys with superior radiation resistance will increase safety margins, design flexibility, and economics for not only the life extension of the existing fleet but also new builds with advanced reactor designs. The Electric Power Research Institute (EPRI) teamed up with Department of Energy (DOE) to initiate the Advanced Radiation Resistant Materials (ARRM) program, aiming to develop and test degradation resistant alloys from current commercial alloy specifications by 2021 to a new advanced alloy with superior degradation resistance in light water reactor (LWR)-relevant environments by 2024. Corrosion resistance in water environment is one of the fundamental properties required for LWR core internal materials. High-temperature steam oxidation tests are not only an accelerated life testing method to uncover potential failure modes in a short period of time, but also an approach to evaluate materials’ resistance to accidental scenarios. Coupons, prepared from fourteen candidate alloys that were selected under the ARRM program, were exposed to 1 bar full steam with ~10 part-per-billion oxygen content at 600 and 650°C for up to 5,000 h, which were weighed at 500-h intervals. Ni-base superalloys are an important class of alloys for reactor applications. Alloys 690, 725, and X- 750 were three of the selected Ni-base superalloys exposed to the steam tests. This report summarizes the metallurgical aspects, such as alloy thermodynamics and the nature of the oxides and the diffusivities of primary elements, and their effects on oxidation behavior of the three alloys. In addition to monitoring mass change, microstructures of the 5000h-exposed samples of alloys 690, 725, and X-750 were characterized using scanning and transmission electron microscopy and energy dispersive x-ray spectroscopy. Together with thermodynamic calculations, the scale constitution and its exfoliation behavior were discussed. Based on experimental and theoretical values, a new model was proposed to quantitatively estimate the metal thickness loss of the alloys. Alloy X-750 was found to have the best resistance to steam oxidation with the least metal thickness loss (<1 μm), which were slightly superior to alloy 690. Alloy 725 exhibited the worst resistance to steam oxidation with the greatest metal thickness loss, e.g., ~2.5 μm at 650°C, which is nearly three times of the metal thickness losses of alloys 690 and X-750 at 650°C. The greatest metal thickness loss of alloy 725 might be attributable to its high Mo content. Photos of the fracture toughness tested samples of eight alloys are presented, which will be correlated with their fracture toughness results and planned tensile test results to select representative alloy samples for detailed microstructural characterization to reveal their microstructure and properties relationships.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗