SEARCH · Search NASA
Results for “microstructure engineering”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Creep behavior of high-entropy alloys: A critical review
High-entropy alloys (HEAs) have been extensively investigated during the last two decades. While substantial progress has been made in understanding their phase stability, microstructure, and deformation mechanisms at room and cryogenic temperatures, the long-term creep behavior (>100 h) of HEAs at high temperatures (>0.6 T m , where T m is the melting temperature) remains relatively underexplored. This knowledge gap is critical, as many engineering applications, including those for power generation and propulsion, require materials with good creep resistance to maintain structural integrity over extended service lifetimes. This review provides a focused and critical assessment of the current understanding of high-temperature deformation and creep behavior of HEAs, with particular attention paid to face-centered cubic HEAs and body-centered cubic refractory HEAs. The underlying deformation mechanisms governing their creep response and the influence of phase stability at elevated temperatures are examined in detail. Recent studies reveal mechanistic differences between HEAs and conventional dilute alloys that do not always lead to improved creep resistance belying their initial promise. Based on these findings, we discuss the challenges in designing HEAs for high-temperature structural applications and outline future research directions that may lead to creep-resistant HEAs.
High-temperature strengthening mechanisms of Laves and B2 precipitates in a novel ferritic alloy
Precipitates of the Laves and B2 phases were engineered in a newly-designed advanced ferritic alloy. Under creep test at 650 °C with 120 MPa, the material showed a steady-state minimum creep rate of 1 × 10 –4 h –1 , about one order of magnitude lower than T91. Microstructural characterization of the ferritic alloy revealed primarily ductile and partially brittle fractures after the creep test. Coarse Laves phase (~ 1 µm) was observed associating with the brittle fracture, resulting in reduced creep ductility. However, fine Laves phase precipitates (~ 100 nm) helped the dimple-ductile fracture and strengthened the material through impeding the motion of dislocations and boundaries. Unlike the B2 precipitates remained coherent exerting the classic Orowan bypassing mechanism at the brittle location, some of the B2 precipitates at the ductile location became incoherent and can develop an attractive interaction with dislocations. In conclusion, this coherency change of B2 precipitates, together with the nucleation of ultrafine (~ 40 nm) Laves phase precipitates during the creep test, would compensate for the coarsening-induced loss of Orowan strengthening of coherent B2 precipitates.
Creep lifetime and microstructure evolution in boron-added 9Cr–1Mo heat-resistant steel
Not provided.
Nanotwin stability in alloyed copper under ambient and cryo-temperature dependent deformation states
Nanometer size grains, solid solution strengthening, low temperatures, and a high density of nanotwins can provide significant strengthening to a material. Nevertheless, under loading the microstructure may evolve altering the effect of grain size, twin density, etc. on this strengthening. In some cases, these effects can be coupled as in detwinning, which is a mechanism for cryogenic grain growth. Here, in this work, a series of copper nanotwinned columnar grains are solid solution alloyed with aluminum and subject to ambient and cryogenic (–196 °C) environments during mechanical indentation, with the influence of alloying on the detwinning evolution studied. Under indentation, at a lower aluminum solute content (2 at.%), the columnar grains bent corresponding to a loss of twins. At a higher aluminum solute content (8 at.%), the grains shear and retain the nanotwins. Atomistic-scale simulations reveal an increase in the incoherent twin boundary velocity with decreasing temperature, but this boundary velocity is reduced with increasing alloy solute content. The coupling of solid solution strengthening and nanotwin stabilization is then used to explain the microstructural stability as a function of indentation at different temperature conditions.
Evolution of microstructure and mechanical properties of selective laser melted Ti-5Al-5V-5Mo-3Cr after heat treatments
Titanium alloy Ti5553 (Ti-5Al-5Mo-5V-3Cr) is an excellent candidate for structural applications and additive manufacturing processes, since, unlike Ti6Al4 V, when built via selective laser melting and/or post additive manufactured welding, it maintains a near-beta microstructure that is both ductile and high strength. Another feature is that Ti5553 properties are adaptable through post build heat treatment. This study explores the heat treatability of selective laser melted Ti5553 up to temperatures approaching the β-transus. Here the results show strength increases while maintaining ductility at high temperatures (700–800°C), but embrittlement occurs at intermediate temperatures (400–600°C) likely due to changes in volume fraction and morphology of the α-phase and/or the presence of the ω-phase. Microstructure and X-ray diffraction are reported after heat-treating to better understand this mechanical response.
Microstructural Materials Design Via Deep Adversarial Learning Methodology
Identifying the key microstructure representations is crucial for computational materials design (CMD). However, existing microstructure characterization and reconstruction (MCR) techniques have limitations to be applied for microstructural materials design. Some MCR approaches are not applicable for microstructural materials design because no parameters are available to serve as design variables, while others introduce significant information loss in either microstructure representation and/or dimensionality reduction. In this work, we present a deep adversarial learning methodology that overcomes the limitations of existing MCR techniques. In the proposed methodology, generative adversarial networks (GAN) are trained to learn the mapping between latent variables and microstructures. Thereafter, the low-dimensional latent variables serve as design variables, and a Bayesian optimization framework is applied to obtain microstructures with desired material property. Due to the special design of the network architecture, the proposed methodology is able to identify the latent (design) variables with desired dimensionality, as well as capturing complex material microstructural characteristics. The validity of the proposed methodology is tested numerically on a synthetic microstructure dataset and its effectiveness for microstructural materials design is evaluated through a case study of optimizing optical performance for energy absorption. Additional features, such as scalability and transferability, are also demonstrated in this work. In essence, the proposed methodology provides an end-to-end solution for microstructural materials design, in which GAN reduces information loss and preserves more microstructural characteristics, and the GP-Hedge optimization improves the efficiency of design exploration.
Novel dense membrane for hydrogen separation for energy applications
The main objectives of this project are: (1) Characterization of the thermo mechanical properties of the novel dense HTM bulk sample; (2) Development of a correlation among the intrinsic factors (such as grain size and phase distribution), and the extrinsic factors (such as temperature and atmosphere) and the thermo-mechanical properties (such as strengths and stress) to predict the performance of a HTM system (HTM membrane and porous substrate) ; and (3) Evaluation of the stability of the novel HTM membrane and its property correlations after thermal cycling. Based on all results and analysis of the thermo mechanical properties for the HTM cermet bulk samples, several important conclusions were made. The mean σfs at room temperature is approximately 356 MPa for the HTM cermet. The mean σfs value decreases to 284 MPa as the temperature increases to 850?C. The Difference difference in atmosphere, such as air or N2, had an insignificant effect on the flexural strength values at 850?C for the HTM cermet. The HTM cermet samples at room temperature and at 500?C fractured without any significant plastic deformation. Whereas, at 850?C, the HTM cermet samples fractured, preceded by an extensive plastic deformation. It seems that the HTM cermet behaves more like an elastic material such as a nonmetal ceramic at the room temperature, and more like a ductile material at increased temperature (850?C). The exothermic peak during the TG/DTA tests centered at 600?C is most likely associated with both the enthalpy change of transformation from the amorphous phase into crystalline zirconia and the oxidation of Pd phase in HTM cermet in air. The endothermic peak centered at 800?C is associated with the dissociation of PdO to Pd for the HTM cermet sample in both inert N2 environment and air. There is a corresponding weight gain as oxidation occurs for palladium (Pd) phase to form palladium oxide (PdO) and there is a weight loss as the unstable PdO is dissociated back to Pd and oxygen. The normal stress and shear stresses from the Mohr?s circle indicate that the residual stress in the HTM cermet sample is mainly as compressive residual stress in the magnitude of -135 to -155 MP, and with very little shear stress (in the magnitude of 10 MPa). The magnitude of change in the normal stress and the shear stress is insignificant in the HTM after 120 thermal cycles. However, the principle normal stress changes from compressive to tensile residual stress and there is a significant increase in the shear stress after 500 thermal cycles. The calculated value based on the equation and the Mohr?s circle is found to be consistent with the experimental value for the as-received HTM cermet samples. At some rotation (φ) angle, the residual stress was found to be as tensile stress. Most ceramic material is weak in tension, and develops microscopic cracks. With treatment of 120 thermal cycles between 50?850?C, the HTM- sample exhibited thermally-induced cracks on the surface. Visually observable cracks appeared on the surface of HTM cermet with continuous thermal cycling, after 500 thermal cycles. The XRD powder diffraction analysis indicated an increased amount of crystalline PdO crystalline in HTM cermet after 120 and 500 thermal cycles as compare to the as-received samples. The Pd crystalline peaks were found to significantly decrease in peak intensity with thermal cycling. Higher peak intensity for PdO phase was observed with increased number of thermal cycles. A Monoclinic monoclinic zirconia phase was first identified in the as-received HTM as-received sample. However, with thermal cycling treatment of both 120 and 500 thermal cycles, the M-ZrO2 phase is transformed to the tetragonal YSZ, which is consistent with the thermal analysis results by TG/DTA. Correlations of the microstructural and thermo-mechanical properties of both selected reference material and ANL-3e HTM cermet bulk sample are affected mainly by porosity and microstructural features, such as grain size and pore size/distribution. The Young?s Modulus (E-value), especially, is positively proportional to the flexural strength for materials with similar crystallographic structure. For different crystallographic materials, physical properties such as E and density are independent of mechanical properties, such as flexural strength.. Microstructural properties, particularly, grain size and crystallographic structure, and thermodynamic properties are the main factors affecting the mechanical properties at both room and high temperatures. The oxidation and the plasticity of Pd phase mainly affect the mechanical properties of HTM cermet at high temperature or with thermal cycling treatment. Changes in the residual stress and microstructure affect the mechanical properties of HTM when subjected to high temperature or thermal cycling treatment.
SISGR -- Domain Microstructures and Mechanisms for Large, Reversible and Anhysteretic Strain Behaviors in Phase Transforming Ferroelectric Materials
This four-year project (including one-year no-cost extension) aimed to advance fundamental understanding of field-induced strain behaviors of phase transforming ferroelectrics. We performed meso-scale phase field modeling and computer simulation to study domain evolutions, mechanisms and engineering techniques, and developed computational techniques for nanodomain diffraction analysis; to further support above originally planned tasks, we also carried out preliminary first-principles density functional theory calculations of point defects and domain walls to complement meso-scale computations as well as performed in-situ high-energy synchrotron X-ray single crystal diffraction experiments to guide theoretical development (both without extra cost to the project thanks to XSEDE supercomputers and DOE user facility Advanced Photon Source).
Multiphysics Degradation Modeling of Energy Storage Materials via RKPM with a Neural Network-Enhancement
In energy storage materials, strong electrochemical-mechanical coupling and highly anisotropic material properties contribute to the formation and propagation of micro-cracking during charge/discharge cycling, resulting in reduced performance and service life. A coupled electro-chemo-mechanical reproducing kernel particle method (RKPM) formulation is developed, and a patch-test is formulated to certify optimal convergence of the proposed RKPM method for the coupled physics system. With microstructural images supplied by the National Renewable Energy Laboratory (NREL), pixel-based model construction by RKPM is then used to represent the complex material microstructures for modeling the coupled physics of these systems. Further, a neural network-enhanced reproducing kernel particle method (NN-RKPM) [1, 2] is introduced to effectively model damage and crack propagation in the material microstructures; the location, orientation, and solution transition near a localization are automatically captured by superimposed block-level NN optimizations. This NN enrichment approach allows for effective modeling of localizations via a fixed background discretization, relieving tedious efforts for adaptive refinement in traditional mesh-based methods. Applications to the heterogeneous microstructures of Li-ion battery cathodes will be presented to demonstrate the effectiveness of the proposed methods. Reference: [1] Baek, J., Chen, J. S., Susuki, K., "Neural Network enhanced Reproducing Kernel Particle Method for Modeling Localizations," International Journal for Numerical Methods in Engineering, Vol. 123, pp 4422-4454, https://doi.org/10.1002/nme.7040, 2022. [2] Baek, J., Chen, J. S., "A Neural Network-Based Enrichment of Reproducing Kernel Approximation for Modeling Brittle Fracture", Computer Methods in Applied Mechanics and Engineering Vol. 410, 116590, 2024.
Crystal Plasticity Model Validation Using Combined High-Energy Diffraction Microscopy Data for a Ti-7Al Specimen
High-Energy Diffraction Microscopy (HEDM) is a 3-d x-ray characterization method that is uniquely suited to measuring the evolving micromechanical state and microstructure of polycrystalline materials during in situ processing. The near-field and far-field configurations provide complementary information; orientation maps computed from the near-field measurements provide grain morphologies, while the high angular resolution of the far-field measurements provide intergranular strain tensors. The ability to measure these data during deformation in situ makes HEDM an ideal tool for validating micro-mechanical deformation models that make their predictions at the scale of individual grains. Crystal Plasticity Finite Element Models (CPFEM) are one such class of micro-mechanical models. While there have been extensive studies validating homogenized CPFEM response at a macroscopic level, a lack of detailed data measured at the level of the microstructure has hindered more stringent model validation efforts. Here, we utilize an HEDM dataset from an alphatitanium alloy (Ti-7Al), collected at the Advanced Photon Source, Argonne National Laboratory, under in situ tensile deformation. The initial microstructure of the central slab of the gage section, measured via near-field HEDM, is used to inform a CPFEM model. The predicted intergranular stresses for 39 internal grains are then directly compared to data from 4 far-field measurements taken between ~4% and ~80% of the macroscopic yield strength. In conclusion, the intergranular stresses from the CPFEM model and far-field HEDM measurements up to incipient yield are shown to be in good agreement, and implications for application of such an integrated computational/experimental approach to phenomena such as fatigue and crack propagation is discussed.
Microstructural analysis of fine-grained magnesium after cyclic tension–tension fatigue testing at 0 °C
Not Available
Mechanisms of paint bake response in resistance spot-welded first and third generation AHSS
Implementation of 3rd generation advanced high strength steels (3GAHSS) in automotive structures requires careful consideration of joining process implications. Due to the presence of increased carbon equivalent in 3GAHSS such as 980 HF relative to commonly-applied 1st generation AHSS such as 980 DP, the resultant properties of the weld nugget and heat affected zones in resistance spot welded must be engineered to provide consistent and acceptable performance, specifically in cross-tension loading mode. Although the as-welded cross-tension strength (CTS) of 980 HF is less than 980 DP, there is a significant improvement of the CTS after paint baking in 980 HF welds. 980 DP steel welds do not exhibit such marked improvement upon baking. The mechanism of the strong and beneficial effect of paint baking on 980 HF in comparison to 980 DP is discussed in light of its effect on residual stress distributions and microstructures. Although residual stress (strain) reduction is observed via synchrotron x-ray diffraction for all tested steels, this effect is demonstrated as secondary to the performance restoration of the weld joint in cross tension. High-resolution electron channeling contrast imaging (ECCI) micrographs reveal that paint baking affects a more beneficial degree of martensite tempering in 980 HF as compared to 980 DP. The martensite tempering is also evidenced by both a reduction in nano-hardness of critical microstructural features and re-emergence of ductile fracture behavior following the paint baking process. The tempering of martensite is concluded to be the dominant mechanism in improving cross tension strength of 3GAHSS welds following paint baking.
A Machine Learning Approach to Quantitative Analysis of Enamel Microstructure from Scanning Electron Microscopy Images
Dental enamel, the outermost tissue of mammalian teeth, must withstand a lifetime of wear and cyclic contact. To meet this demand, enamel possesses a combination of high hardness and resistance to fracture, properties that are typically mutually exclusive. The impressive damage tolerance has been attributed largely to decussation of the enamel rods, the principal unit of its microstructure. As such, enamel is inspiring the design of next‐generation structural materials. However, quantitative descriptions of the decussated enamel rod microstructure remain limited due to challenges encountered in applying computed tomography and in acquiring quality images appropriate for traditional digital processing methods. Here, a machine learning segmentation method is applied to images of the enamel obtained using scanning electron microscopy to support quantitative analysis of the microstructure. A pretrained convolutional neural network is used to expand the input training image dataset to allow the training of a random forest classifier, which ultimately segments the image with a very small training set ( n = 3 images). A validation of this segmentation method is presented, in addition to its application to calculate relevant microstructural parameters for images of tooth enamel from selected mammalian species. The methodology applied here is equally applicable to other hard tissues.
A mean field homogenization model for the mechanical response of ceramic matrix composites
SiC/SiC composites offer exceptional mechanical stability at high temperatures and under irradiation. These ceramic matrix composites are therefore strong candidate materials for future nuclear energy applications. Their mechanical response, which exhibits pseudo-plasticity, is mediated by matrix cracking, fiber debonding, and fiber pull-out due to slip. Here, this study introduces a mechanistic model for the behavior of unidirectionally reinforced SiC/SiC composites. Specifically a mean field homogenization approach is proposed to account for all deformation and degradation modes during mechanical deformation. The homogenization scheme relies on a Mori Tanaka method that is extended to consider the effects of the coating’s elasto-plastic response on the development of micromechanical fields. Further, the model proposed introduces a method to effectively account for the role of localized damage (i.e., cracks) on mechanical fields within both the fiber and the matrix. Upon validating the model against experimental data, the roles of interface sliding, coating dimensions and intrinsic elastic response, as well as of microstructure (e.g. porosity, fiber volume fraction) are discussed.
An Eulerian crystal plasticity framework for modeling large anisotropic deformations in energetic materials under shocks
Here, this paper demonstrates a novel Eulerian computational framework for modeling anisotropic elastoplastic deformations of organic crystalline energetic materials (EM) under shocks. While Eulerian formulations are advantageous for handling large deformations, constitutive laws in such formulations have been limited to isotropic elastoplastic models, which may not fully capture the shock response of crystalline EM. The present Eulerian framework for high-strain rates, large deformation material dynamics of EM incorporates anisotropic isochoric elasticity via a hypo-elastic constitutive law and visco-plastic single-crystal models. The calculations are validated against atomistic calculations and experimental data and benchmarked against Lagrangian (finite element) crystal plasticity computations for shock-propagation in a monoclinic organic crystal, octahydro-1,3,5,7-tetranitro-1,3,5,7 tetrazocine (β-HMX). The Cauchy stress components and the resolved shear stresses calculated using the present Eulerian approach are shown to be in good agreement with the Lagrangian computations for different crystal orientations. The Eulerian framework is then used for computations of shock-induced inert void collapse in β-HMX to study the effects of crystal orientations on hotspot formation under different loading intensities. The computations show that the hotspot temperature distributions and the collapse profiles are sensitive to the crystal orientations at lower impact velocities (viz., 500 m/s); when the impact velocity is increased to 1000 m/s, the collapse is predominantly hydrodynamic and the role of anisotropy is modest. The present methodology will be useful to simulate energy localization in shocked porous energetic material microstructures and other situations where large deformations of single and polycrystals govern the thermomechanical response.
Asphaltene-induced spontaneous emulsification: Effects of interfacial co-adsorption and viscoelasticity
Asphaltenes are a class of high molecular weight aromatic compounds found in crude oil. They adsorb onto toluene-water interfaces and induce a spontaneous emulsification phenomenon, whereby stable water-in-oil emulsions form without the need of an external energy input. This work aims to control and understand the factors affecting spontaneous droplet formation in the presence of asphaltene adsorption. This is particularly useful for crude oil refining, where the presence of a stable emulsion hampers the efficiency of downstream processing operations. We explore the effect of the addition of copolymers designed as crude oil flow improvers as a means to control the extent of emulsion formation. We find that the polymers competitively adsorb onto the toluene-water interface and diminish spontaneous emulsification. Additionally, we conduct fluorescence microscopy experiments and measurements of the interfacial energy to determine the mechanism of spontaneous emulsification in asphaltene systems. We conclude that an emulsion forms via the diffusion of molecular water into the oil phase and subsequent binding with asphaltene aggregates, leading to the nucleation of micrometer-sized water droplets. We find that the polymer forms complexes with the dissolved asphaltenes, possibly hampering the ability of diffused water to bind to the asphaltenes and reducing the extent of spontaneous emulsification. Finally, we investigate the role of interfacial shear and dilatational viscoelasticity to better understand which fundamental interfacial properties are important in the emulsification of asphaltene-laden systems. We find that the rate of formation of an interfacial microstructural network is inversely correlated with the extent and rate of spontaneous emulsification.