Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Effect of counterface material type and its topography on the tribological properties of polyimide composites

Graphite fiber reinforced polyimide composite pins were slid against seven different counterfaces to determine the effect of material type on the tribological properties of polymer composites. In addition, the effect of sliding a new pin on a pre-established transfer film was investigated. The results indicated that almost a five order of magnitude difference in composite wear rate can occur just by varying the counterface material. An attempt to make all surfaces as smooth as possible was made, but due to differences in material composition this was not possible and a range of surface roughnesses were obtained. The results indicate that the smoother the surface, the lower the composite wear rate; but that small protrusions (not discernible with arithmetic surface roughness measurements) can markedly increase wear rates. A pre-established transfer film improved both run in and steady state wear rates.

Fusaro, R. L.↗

Counterface effects on the tribological properties of polyimide composites

Graphite fiber reinforced polyimide composite pins were slid against seven different counterfaces to determine the effect of material type on the tribological properties of polymer composites. In addition, the effect of sliding a new pin on a pre-established transfer film was investigated. The results indicated that almost a five order of magnitude difference in composite wear rate can occur just by varying the counterface material. An attempt to make all surfaces as smooth as possible was made, but due to differences in material composition this was not possible and a range of surface roughnesses were obtained. The results indicate that the smoother the surface, the lower the composite wear rate; but that small protrusions (not discernible with arithmetic surface roughness measurements) can markedly increase wear rates. A pre-established transfer film improved both run in and steady state wear rates.

Fusaro, Robert L.↗

Macroscale Superlubricity Induced by MXene/MoS 2 Nanocomposites on Rough Steel Surfaces under High Contact Stresses

Toward the goal of achieving superlubricity, or near-zero friction, in industrially relevant material systems, solution-processed multilayer Ti 3 C 2 T x -MoS 2 blends are spray-coated onto rough 52100-grade steel surfaces as a solid lubricant. The tribological performance was assessed in a ball-on-disk configuration in a unidirectional sliding mode. The test results indicate that Ti 3 C 2 T x -MoS 2 nanocomposites led to superlubricious states, which has hitherto been unreported for both individual pristine materials, MoS 2 and Ti 3 C 2 T x , under macroscale sliding conditions, indicating a synergistic mechanism enabling the superlative performance. Furthermore, the processing, structure, and property correlation were studied to understand the underlying phenomena. Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy revealed the formation of an in situ robust tribolayer that was responsible for the performance at high contact pressures (>1.1 GPa) and sliding speeds (0.1 m/s). This report presents the lowest friction obtained by either MoS 2 or MXene or any combination of the two so far.

36 MATERIALS SCIENCE↗

Structural and Mechanical Properties of Zr-Si-N Coatings Deposited by Arc Evaporation at Different Substrate Bias Voltages

ZrN and Zr-Si-N coatings were formed using vacuum-arc plasma fluxes deposition system at the substrate bias voltage (U{sub B}) ranged from − 50 to − 220 V on HS6-5-2 steel substrates. The structural, mechanical and tribological properties were characterized using x-ray diffraction, atomic force microscopy, scanning electron microscopy, optical microscopy, nanoindentation and ball-on-disk test. The surface roughness parameter Ra of ZrN coatings is lower than Zr-Si-N coatings. Both roughness Ra of Zr-Si-N coatings and the number of surface defects with mainly small dimensions to 1 µm decrease with increasing negative substrate bias voltage. The addition of silicon to ZrN significantly reduces the crystallite size, from about 18.3 nm for ZrN coating to 6.4 nm for Zr-Si-N coating both deposited at the same U{sub B} = − 100 V and 7.8 nm for U{sub B} = − 150 V. The hardness of Zr-Si-N coatings increases to about 30 GPa with the increase in negative substrate bias voltage (U{sub B} = − 220 V). Adhesion of the coatings tested is high, and critical load is above 80 N and reduces with U{sub B} increase. Coefficient of friction determined using AFM shows similar trend as surface roughness in microscale.

36 MATERIALS SCIENCE↗

Nb3Sn multicell cavity coating at JLAB

The Nb3Sn-coated cavities aim to enhance perfor-mance and significantly reduce cost. Their fabrication in-volves tin vapor diffusion coating of Nb3Sn on the interior surface of a Nb cavity. Controlled removal of first few lay-ers to obtain a smoother and cleaner surface could be de-sirable to improve the high field RF performance. Our first results from the application of electropolishing and oxy-polishing techniques on Nb3Sn-coated surfaces indicated reduced surface roughness, and the surface composition appeared nominally unchanged. Systematic studies explore the effect of different polishing parameters into the rough-ness and composition. We present the latest results from SEM/EDS and AFM studies of Nb3Sn-coated samples treated with electropolishing and oxypolishing.

Pudasaini, Uttar↗

Characterizations of Binary FeCr (AISI 430) Thin Films Deposited from a Single Magnetron Sputtering Under Easy Controllable Deposition Parameters

A series of 50-nm binary FeCr martensitic thin films were sputtered from a single source made of commercial AISI 430 ferritic stainless steel under the deposition rates gradually increased from 0.03 to 0.11 nm/s with 0.02 nm/s steps at stationary condition. And, under 0.09 nm/s deposition rate, a second series of the films were also deposited under the rotation speed of their substrates which was chosen at 0, 25, and 45 rpm. As far as we are concerned, this study is the first investigation of properties of the thin films produced from AISI 430. The atomic Fe content in the films increased from 79.3 to 98.6% while atomic Cr content decreased from 20.5 to 1.2% with the increase of deposition rate from 0.03 to 0.11 nm/s. According to compositional analysis, the Fe content increased while Cr content decreased with increasing deposition rate. The reason for this may be attributed to the relatively different bond energy/melting point of metals which have different contents sputtered from source material since this physical parameter is very significant for the sputtering process. And, the Fe content in the films decreased from 84.9 to 79.2 at. % while the Cr content increased from 14.9 to 20.6 at. % when the increase of rotation speed of substrate. The crystal structure of all films was observed to have a body-centered tetragonal phase and the intensity of (110) peak varied with the atomic Fe content. The surface observations of films performed by a scanning electron microscope exposed that the number of surface grains increased with the increase of deposition rate and decreased with the increase of rotation speed. According to surface roughness analysis done by an atomic force microscope, the roughness of the film surfaces increased as the deposition rate increased. And, the roughness of the film surfaces decreased as the rotation speed increased. This has been consistent with the grain size and roughness parameters. Thus, increasing deposition rate and decreasing rotation speed of the substrate caused an increase in grain size and roughness parameters. The magnetic measurements of the films achieved, by a vibrating sample magnetometer at room temperature, displayed that the saturation magnetization, M{sub s}, values increased from 820.1 to 1700.4 emu/cm{sup 3}, the remanence magnetization, M{sub r}, values increased from 293 to 817 emu/cm{sup 3}, and the coercivity, H{sub c}, value also increased from 38 to 107 Oe with the increasing of deposition rate. It is also seen that the magnetic easy axis are in the film plane due to the shape anisotropy. With the increase rotation speed, the values of M{sub s} and M{sub r} increased and the H{sub c} decreased. It was seen that variation of Fe content in the films influences the M{sub s} values and the H{sub c} values are consistent with the surface properties. It was concluded that the deposition rate and the rotation speed of the substrate play a considerable role on the structural and related magnetic properties of the sputtered FeCr thin films, and the properties of the films can be easily controlled by changing production parameters.

36 MATERIALS SCIENCE↗

Effect of CeO{sub 2} buffer layer on the microstructure and magnetic properties of yttrium iron garnet film on Si substrate

Yttrium iron garnet films were grown by radio frequency magnetron sputtering on Si(111) substrate with and without CeO{sub 2} buffer layer, and influence of CeO{sub 2} buffer on the microstructure and magnetic behaviors of the films were investigated. As compared with the film without buffer, a larger saturation magnetizaton (M{sub s}), lower coercive force (H{sub c}), and higher remnant magnetization (M{sub r}) were obtained due to the introduction of CeO{sub 2} layer. The higher M{sub s} results from the denser structure and the smaller content of Fe{sup 2+} ions. The lower H{sub c} and higher M{sub r} can be explained by the small surface roughness and crystal grains size. The film on CeO{sub 2} buffer layer possess fine microstructure and its surface roughness is smaller than the unbuffered films, which provides an increased exchange between the crystal grains and an enhanced spontaneous magnetization effect, leading to the higher remnant magnetization.

36 MATERIALS SCIENCE↗

Natural garnet reinforced high density polyethylene composites for sustainable microwave substrates

Highlights: • A cost effective and ecofriendly alternative for commercial microwave substrates based on HDPE and Garnet mineral is proposed. • AFM images indicated the surface roughness of the substrate is very low and has the required degree of surface finish to minimize conduction loss. • Composite with 0.5 vol fraction of Garnet has ε{sub r} = 5.7, tan δ = 0.00185 (at 5 GHz), CTE = 114 ppm/{sup o}C and thermal conductivity = 1.3 Wm{sup −1}K{sup −1}. • The moisture absorption and thermal stability of dielectric properties are in the acceptable range for microwave substrate applications. - Abstract: A cost effective and ecofriendly alternative for commercially available microwave substrates is proposed in the present study. A polymer composite based on high-density polyethylene (HDPE) filled with garnet mineral was fabricated using sigma-blend technique with 0.1–0.5-volume fraction of filler. The atomic force microscopic images indicated the surface roughness of the substrate is very low and has the required degree of surface finish to avoid conduction loss. For 0.5 vol fraction of garnet, the composite showed a dielectric constant (ε{sub r}) = 5.7 and dielectric loss (tan δ) = 0.00185 at 5 GHz. Moreover, coefficient of thermal expansion (CTE), thermal conductivity (k{sub c}) and tensile strength are 114 ppm/{sup o}C, 1.3 Wm{sup −1}K{sup −1} and 14.3 MPa respectively for filler volume fraction, V{sub f} = 0.5. The dielectric, thermal, moisture absorption and mechanical properties indicate that the garnet/HDPE composites are ideal candidate for cost effective and sustainable microwave substrates.

36 MATERIALS SCIENCE↗

Evaluation of the soft x-ray reflectivity of micropore optics using anisotropic wet etching of silicon wafers

The x-ray reflectivity of an ultralightweight and low-cost x-ray optic using anisotropic wet etching of Si (110) wafers is evaluated at two energies, C K{alpha}0.28 keV and Al K{alpha}1.49 keV. The obtained reflectivities at both energies are not represented by a simple planar mirror model considering surface roughness. Hence, an geometrical occultation effect due to step structures upon the etched mirror surface is taken into account. Then, the reflectivities are represented by the theoretical model. The estimated surface roughness at C K{alpha} ({approx}6 nm rms) is significantly larger than {approx}1 nm at Al K{alpha}. This can be explained by different coherent lengths at two energies.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Transition Experiments on Blunt Bodies with Distributed Roughness in Hypersonic Free Flight in Carbon Dioxide

Blunt-body geometries were flown through carbon dioxide in the NASA Ames Hypervelocity Free Flight Aerodynamic Facility to investigate the influence of distributed surface roughness on transition to turbulence in CO2-dominated atmospheres, such as those of Mars and Venus. Tests were also performed in air for direct comparison with archival results. Models of hemispherical and spherically-blunted large-angle conical geometries were flown at speeds between 2.8 km/s and 5.1 km/s and freestream pressures between 50 Torr and 228 Torr. Transition fronts were determined from global surface heat flux distributions measured using thermal imaging techniques. Distributed surface roughness was produced by grit-blasting the model surfaces. Real-gas Navier-Stokes solutions were used to calculate non-dimensional correlating parameters at the measured transition onset locations. Transition-onset locations correlated well with a constant roughness Reynolds number based on the mean roughness element height. The critical roughness Reynolds number for transition onset determined for flight in CO2 was 223 +/- 25%. This mean value is lower than the critical value of 250 +/- 20% previously-established from tests conducted in air, but within the bounds of the expected measurement uncertainty.

ballistic ranges↗

Surface Treatment of Powder-Bed Fusion Additive Manufactured Metals for Improved Fatigue Life

High-cycle fatigue (HCF) tests were conducted on samples fabricated by two powder-bed additive manufacturing techniques. Samples were tested with as-produced surfaces and after various non-contact surface improvement treatments. Ti-6Al-4V samples were made using both electron beam melting (EBM) and selective laser melting (SLM), while Inconel 625 was fabricated using SLM. Ti-6Al-4V was treated with a commercial chemically accelerated vibratory polishing process, with target material removal of approximately 200 µm from each surface for EBM samples and 100 µm for SLM samples. This technique led to increases in both the number of cycles before failure at a given loading condition and endurance limit (at 10{sup 7} cycles) compared to samples with as-produced surfaces. The results are interpreted as the reduction in elastic stress concentration factor associated with surface defects where fatigue cracks initiate. SLM 625 was treated with both an abrasive polishing method and laser surface remelting. Both methods led to improvements in surface roughness, but these did not lead to improvements in fatigue properties of SLM 625. For abrasive polished samples, the combination of improved measured surface roughness without fatigue property enhancement suggests that surface material is removed, but the roots of surface defects, where fatigue cracks initiate, were left intact. For laser treatment, the remelted surface layer retained a rapidly solidified microstructure that did not increase the number of cycles before crack initiation even though the surface was smoother compared to the surface prior to polishing.

36 MATERIALS SCIENCE↗

Analysis of Niobium Electropolishing Using a Generalized Distribution of Relaxation Times Method

Using electrochemical impedance spectroscopy, we have devised a method of sensing the microscopic surface conditions on the surface of niobium as it is undergoing an electrochemical polishing (EP) treatment. The method uses electrochemical impedance spectroscopy (EIS) to gather information on the surface state of the electrode without disrupting the polishing reaction. The EIS data is analyzed using a so-called distribution of relaxation times (DRT) method. Using DRT, the EIS data can be deconvolved into discrete relaxation time peaks without any a priori knowledge of the electrode dynamics. By analyzing the relaxation time peaks, we are able to distinguish two distinct modes of the EP reaction. As the polishing voltage is increased, the electrode transitions from the low voltage EP mode, characterized by a single relaxation time peaks, to the high voltage EP mode, characterized by two relaxation time peaks. We theorize that this second peak is caused by the formation of an oxide layer on the electrode. We also find that this oxide induced peak transitions from to a negative relaxation time, which is indicative of a blocking electrode process. By analyzing EPed samples, we show that samples polished in the low voltage mode have significantly higher surface roughness due to grain etching and faceting. We find that the surface roughness of the samples only improves when the oxide film peak is present and in the negative relaxation time region. This shows that EIS combined with DRT analysis can be used to predict etching on EPed Nb. This method can also be performed before or during the EP, which could allow for adjustment of polishing parameters to guarantee a smooth cavity surface finish.

43 PARTICLE ACCELERATORS↗

Resistivity scaling and electron relaxation times in metallic nanowires

We study the resistivity scaling in nanometer-sized metallic wires due to surface roughness and grain-boundaries, currently the main cause of electron scattering in nanoscaled interconnects. The resistivity has been obtained with the Boltzmann transport equation, adopting the relaxation time approximation of the distribution function and the effective mass approximation for the conducting electrons. The relaxation times are calculated exactly, using Fermi's golden rule, resulting in a correct relaxation time for every sub-band state contributing to the transport. In general, the relaxation time strongly depends on the sub-band state, something that remained unclear with the methods of previous work. The resistivity scaling is obtained for different roughness and grain-boundary properties, showing large differences in scaling behavior and relaxation times. Our model clearly indicates that the resistivity is dominated by grain-boundary scattering, easily surpassing the surface roughness contribution by a factor of 10.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Monte Carlo simulation of the effect of soil moisture variation on the microwave emission from soils

In this paper, results of a Monte Carlo simulation of the effect of noise on the relationship between the microwave emissivity of soil and its moisture content are presented. It is found that whenever the magnitude of the noise for the independent variable, in this case the soil moisture, is increased, both the slope of the regression and the correlation coefficient decrease. In particular, when the noise has magnitude equivalent to a coefficient of variation of 0.25, the slope and correlation coefficient are in good agreement with those obtained from the data of a 21-cm airborne microwave radiometer which was flown over a test site in hand county, South Dakota. The comparison was made using a linear relationship to determine the estimated emissivity from the ground measurements of soil moisture. The linear relationship was derived from a radiative transfer model calculation of the microwave emissivities using realistic soil-moisture profiles. The effect of surface roughness was included in the relationship, and the variability of the surface roughness was also simulated by a Monte Carlo technique.

Mo, T.↗

Effects of Laser and Shot Peening on Fatigue Crack Growth in Friction Stir Welds

The effects of laser, and shot peening on the fatigue life of Friction Stir Welds (FSW) have been investigated. The surface roughness resulting from various peening techniques was assessed, and the fracture surfaces microstructure was characterized. Laser peening resulted in an increase in fatigue life approximately 60%, while shot peening resulted in 10% increase when compared to the unpeened material. The surface roughness of shot peening was significantly higher compared to the base material, while specimens processed with laser peening were relatively smooth.

Hatamleh, Omar↗

Radiometry and a thermal modeling of asteroids

The steps required to determine a radiometric diameter of an asteroid from observations of its visual and thermal radiation are described together with thermal models required to predict the emission expected from a body of given size and bolometric albedo. It is pointed out, however, that, in some cases, these models were found to fail for a variety of reasons; in particular, they fail to characterize the shape, surface roughness, the rate and sense of rotation, and the maturity of the surface regolith, all of which affect the observed thermal flux. Several thermal models are examined, including the Standard Thermal Model for asteroids, the fast-rotating (isothermal-latitude) model, the thermophysical model, and the rough-surface thermophysical models.

Lebofsky, Larry A.↗

The application of differential roughness to mitigate friction and wear

By definition, differential roughness occurs where the surface roughness of one region is distinctly different from that of an adjacent region. Differential roughness may occur on a sliding surface when the structure of an area of the surface is modified relative to the original material. Differential roughness may be used to effect a film thickness change so as to cause hydrodynamic or hydrostatic lubrication effects just as if the surfaces were machined. The advantage of differential roughness is that the effective offset of film thickness continues to exist even if there is gross wear. One can effect film thickness changes which are smaller than can be made directly. Furthermore, asperity tip load support is the same over both the high roughness and small roughness regions. The potential uses for differential roughness are seals, bearings, and pumps. Some examples are presented.

Lebeck, Alan O.↗

Microstructure, Processing, Performance Relationships for High Temperature Coatings

This work evaluates the suitability of iron aluminide coatings for use in high temperature fossil fuel combustion environments, such as boiler applications. The coatings are applied using High Velocity Oxy-Fuel (HVOF) thermal spray techniques. Iron aluminide coatings, with the nominal composition of Fe3Al, were applied to various high temperature structural materials (316 Stainless Steel, 9Cr-1Mo steel and Inconel 600) that typically lack inherent resistance to environmental degradation found in fossil fuel combustion atmospheres. Coating/substrate combinations were subjected to thermal cycling to evaluate the effect of HVOF parameters, coating thickness, substrate material and substrate surface roughness on the resistance to coating delamination and cracking. It was found that substrate surface roughness had a profound influence on the performance of a given substrate/coating system and that surface preparation techniques will need to be tailored to the specific substrate material. Also, higher particle velocity during HVOF thermal spray deposition of the iron aluminide coatings tended to result in better-performing coating/substrate systems with less delamination at the coating/substrate interface. Some combinations of HVOF parameters, coating thickness and substrate materials were found to perform extremely well even at temperatures up to 900oC. However, in some cases, substantial reactions at the interface were observed.

20 FOSSIL-FUELED POWER PLANTS↗