SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The statistical summary of data resulting from a mail questionnaire survey designed to develop information on the general aviation single pilot operating under instrument flight rules is presented.
The influence of airplane components, as well as wing location and tail length, on the rotational flow aerodynamics is discussed for a 1/6 scale general aviation airplane model. The airplane was tested in a built-up fashion (i.e., body, body-wing, body-wing-vertical, etc.) in the presence of two wing locations and two body lengths. Data were measured, using a rotary balance, over an angle-of-attack range of 8 deg to 90 deg, and for clockwise and counter-clockwise rotations covering an omega b/2V range of 0 to 0.9.
The future of general aviation, its fuels, and the piston powered fleet of aircraft up to the year 2000, and beyond are considered.
Quality control measures for aviation gasoline, and some of the differences between quality control on avgas and mogas are discussed. One thing to keep in mind is that with motor gasoline you can always pull off to the side of the road. It's not so easy to do in an airplane. Consequently, there are reasons for having the tight specifications and the tight quality control measures on avgas as compared to motor gasoline.
Two different engines were studied. The advantages of a diesel to general aviation were reduced to fuel consumption, reduced operating costs, and reduced fire and explosion hazard. There were no ignition mixture control or inlet icing problems. There are fewer controls and no electrical interference problems.
Values for the stability and control parameters for a general aviation airplane were determined from flight data. Lateral and longitudinal transient maneuvers were analyzed by the equation error and output error methods. There was a good agreement between the parameters extracted from flight data and those predicted by wind tunnel.
Statistical information relating to the number of gas turbine engine rotor failures which occurred during 1979 in commercial aviation service use is provided. The predominant failure mode involved blade fragments, 84 percent of which were contained. No uncontained disk failures occurred and although fewer rotor rim and seal failures occurred, 100 percent and 50 percent, respectively, were uncontained. Sixty-eight percent of the 157 rotor failures occurred during the take-off and climb stages of flight.
A flapped natural laminar flow airfoil for general aviation applications, the NLF(1)-0215F, has been designed and analyzed theoretically and verified experimentally in the Langley Low Turbulence Pressure Tunnel. The basic objective of combining the high maximum lift of the NASA low speed airfoils with the low cruise drag of the NACA 6 series airfoils has been achieved. The safety requirement that the maximum lift coefficient not be significantly affected with transition fixed near the leading edge has also been met. Comparisons of the theoretical and experimental results show generally good agreement.
The development of a new increased range higher visibility was investigated. The visibility sensor that is currently is the Transmissometer. Current transmissometer technology provides only a factor of 10 dynamic range with a single base line. The FAA is preparing to install automated weather observing systems (AWOS) at many locations. These systems require visibilities up to approximately 5 miles. To use a transmissometer for this type of measurement, the base line must be about 1,000 feet; where alignment becomes very difficult to maintain. New technologies were developd for measuring visibility. Improved transmissometers, forward-scatter meters and back-scatter meters have become available. A current practical issue for visibility sensors is how to specify one that is good enough to meet the needs of aviation. The first question is what performance is required; how accurately must the sensor measure? Visibility sensors do not actually measure the visibility directly. The purpose of measuring the visibility is to predict what the pilot will see a considerable distance away from the sensor location. The atmosphere introduces considerable variation in the measurement and the basic sensor accuracy needed is difficult to define. The second question for high visibilities is what to use as the standard reference sensor. The third question pertains to the competitive procurement of visibility sensors, which is mandated at present. Two acceptance test procedures to be used to insure satisfactory sensor performance is examined.
Tables of incremental gust and maneuver accelerations in 0.1g intervals (above preselected threshold values) and derived gust velocities in intervals of 4 ft/sec are presented for 95 general aviation airplanes flown for 35,286 hours in 9 types of operations.
The development of a data acquisition/reduction system for use in the flight testing of general aviation aircraft is described. Design objectives for the system are adequate accuracy, ease of installation and removal from aircraft, simplicity of operation, and low cost. A 16-channel working system has been constructed, and tested in the collection of flight test data from a Cessna 172 aircraft, which uses as the basis of its design an AIM65 microcomputer. Data is reduced with a MINC minicomputer system. Attention is given to the onboard installation of computer, battery and transducer modules incorporated by the system.
A design study has been conducted to optimize trim cruise flight of high performance general aviation canard aircraft which achieve minimum drag. In order to investigate the advantages and disadvantages of canard configured aircraft, corresponding conventional tail-aft 'baseline' aircraft were designed and used for comparison. Two-dimensional predictions were obtained by coupling inviscid results from a vortex panel multi-element program to a momentum integral boundary layer analysis. Using the results of the two-dimensional vortex panel analysis, a vortex lattice method was employed to predict the finite wing results. The analysis utilized a turbulent airfoil and a natural laminar airfoil which are two NASA state-of-the-art airfoil sections. The canard aircraft designs give quantitative results of wing and canard loadings, wing-to-canard moment arm ratios, and aspect ratio effects for trim cruise flight for a wide range of wing-to-canard area ratios. Both canard and baseline aircraft achieved a 25 to 30 percent improvement in performance over typical current technology aircraft, but high canard loading necessary for trim resulted in slightly poorer performance of the canard aircraft as compared to the baseline designs.
The field phase of the Joint Airport Weather Studies (JAWS) Project was conducted in the vicinity of Denver's Stapleton International Airport from 15 May to 13 August 1982. The primary collection systems were three Doppler radars, a 27-station, closely spaced (4 km) network of surface stations, and five research aircraft. The program was specifically planned to observe wind shear phenomena with high time and space resolution that would be dangerous to aircraft operations. The program was successful in observing a large number of such events. Preliminary conclusions are presented on the effectiveness of several wind shear detection systems to warn of wind shear events critical to aviation safety.
A set of flight tests designed to evaluate the relative utility of candidate displays with advanced symbology for general aviation terminal area instrument flight rules operations are discussed. The symbology was previously evaluated as part of the NASA Langley Research Center's Terminal Configured Vehicle Program for use in commercial airlines. The advanced symbology included vehicle track angle, flight path angle and a perspective representation of the runway. These symbols were selectively drawn on a cathode ray tube (CRT) display along with the roll attitude, pitch attitude, localizer deviation and glideslope deviation. In addition to the CRT display, the instrument panel contained standard turn and bank, altimeter, rate of climb, airspeed, heading, and engine instruments. The symbology was evaluated using tracking performance and pilot subjective ratings for an instrument landing system capture and tracking task.
A linguistic method for the analysis of small group discourse, was developed and the use of this method on transcripts of commercial air transpot accidents is demonstrated. The method identifies the discourse types that occur and determine their linguistic structure; it identifies significant linguistic variables based upon these structures or other linguistic concepts such as speech act and topic; it tests hypotheses that support significance and reliability of these variables; and it indicates the implications of the validated hypotheses. These implications fall into three categories: (1) to train crews to use more nearly optimal communication patterns; (2) to use linguistic variables as indices for aspects of crew performance such as attention; and (3) to provide guidelines for the design of aviation procedures and equipment, especially those that involve speech.
A quiet, clean, general aviation, turbofan engine was instrumented to measure the fluctuating pressures in the combustor, turbine exit duct, engine nozzle and the far field. Both a separate flow nozzle and an internal mixer nozzle were tested. The fluctuating pressure data are presented in overall pressure and power levels and in spectral plots. The combustor data are compared to recent theory and found to be in excellent agreement. The results indicate that microphone correction procedures for elevated mean pressures are questionable. Ordinary coherence function analysis suggests the presence of an additional low frequency noise source downstream of the turbine that is due to the turbine itself. Low frequency narrowband data and coherence function analysis are presented.
A review of aircraft controls research in the general aviation field is given. Among the topics included are: controls technology benefits, military and commercial test programs, flight tests, ride quality control, and wind loading.
Wind-tunnel tests of a model of an advanced canard configuration designed for general aviation were conducted in the Langley 30- by 60-Foot Tunnel. The objective of the tests was to determine the aerodynamic stability and control characteristics of the configuration for a large range of angles of attack and sideslip at several power conditions. Analysis of the aerodynamic data indicates significant effects of power and of center-of-gravity location. For forward center-of-gravity locations, the configuration had extremely stall-resistant stability and control characteristics. For aft center-of-gravity locations and high-power conditions, the combined effects of increased pitch control and reduced longitudinal stability overpowered the stall resistance provided by the canard, which led to a high-angle-of-attack, deep-stall trim condition. Other aspects of the aerodynamic characteristics studied include the following: flow-visualization study, effect of negative angles of attack, lateral-directional characteristics, and comparison of the stall characteristics with another canard configuration.