Search NASA⌕ Search

SEARCH · Search NASA

Results for “Best”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Flow pattern and void fraction characterization in nitrogen/water flows through a diamond-type triply periodic minimal surface lattice

Here, this study presents, to the authors knowledge, the first experimental investigation on the void fraction and flow patterns in two-phase flows through a diamond-type Triply Periodic Minimal Surface (TPMS) lattice. An additively manufactured TPMS structure was tested under upward co-current flow of a water/nitrogen mixture. Superficial velocities varied for a total of 42 test conditions (gas: 0.01–2.4 m/s; liquid: 0.01–2.4 m/s; mass flux: 20–2370 kg/m 2 ·s). High-speed video and X-ray imaging enabled time-averaged void fraction measurements and identified six distinct flow regimes which were used to develop a flow pattern map. Comparison of the void fraction data with correlations from literature demonstrated the Rouhani and Axelsson (1970) [49] correlation modified by Steiner (1993) [52] provided the best agreement, which was improved with empirically fit coefficients. This approach predicted the void fraction with errors < ±20% for 64% of the data, with a mean absolute percent deviation (MAPD) of 23%. The measured frictional pressure drop was compared to correlations from literature which captured the observed trends but did not provide good accuracy. The best agreement was found after optimizing the empirical coefficients of the Muller-Steinhagen & Heck (1986) [56] correlation; this approach captured 33% of the data within ±20% with a MAPD of 46% over the full range and captured 71% of the data within ±20% a MAPD of 13.3% at mass fluxes >1100 kg/m 2 -s. These results provide foundational insight into TPMS two-phase flow behavior and inform modeling and design of advanced heat exchange components incorporating TPMS geometries.

42 - ENGINEERING↗
DOE OSTI2021

Quantifying physical parameterization uncertainties associated with land-atmosphere interactions in the WRF model over Amazon

The Weather Research and Forecasting (WRF) model can be used to diagnose regional land-atmosphere (L-A) coupling strength in the absence of sufficient observations but subjected to uncertainties associated with model physical parameterizations. In this study, we propose a framework to quantify and reduce model physical parameterization uncertainties associated with surface fluxes and L-A coupling. An ensemble of WRF simulations with different physical schemes is used to simulate surface fluxes and land-atmosphere coupling strength over the Amazon region. The physical parameterizations investigated include cloud microphysics (MP), land surface processes (LSM), planetary boundary layer (PBL), surface layer (SL), and cumulus (CU). We perform 120 ensemble simulations using the WRF model and different combinations of six MPs, three LSMs, six PBLs and SLs and three CUs. The measurements from the GoAMAZON field campaign and satellite data are used to evaluate model performance. A Multi-way analysis of variance (ANOVA) approach is applied to quantify the relative importance of different physics processes on L-A coupling. The Tukey’s test is used to sort schemes that have no significant differences into one group. The suite of physics that result in the best simulations of the corresponding variables are selected based on the Taylor skill score. Results show that the relative importance of processes and their interaction vary with the variables of interest. For example, CU was the most important process in modulating soil moisture, 2 m-humidity, latent heat, and net radiation. LSM showed dominant effects on 2 m-temperature and also has the largest impact on sensible heat and the lifting condensation level. The best physical parameterization ensembles show much narrower ranges of the variables of interest than the priori ensemble. Results of this study show the roles of different physical processes in modulating L-A interactions, quantify model uncertainties from physical processes, and provide insights for improving the model physics parameterizations.

Wang, Chen↗
DOE OSTI2025

Process design and techno-economic analysis for bio-based graphite and liquid hydrocarbons production from lignocellulosic biomass

The worldwide demand for graphite, as the main anode material for Li-ion batteries, is expected to double by 2028 since it supports the use of electricity, including transient renewable sources, for energy storage, sustainable mobility, and automation. However, the dependence on non-renewable and external resources jeopardizes the world supply chain. This study explores the technical and economic performance of transforming lignocellulosic biomass into biographite and fuel-grade hydrocarbons through pyrolysis bio-oil upgrading. According to simulation results, the total power demand for the biorefinery reached 10,784 kWh per tonne of biographite, of which 36 % can be supplied by the heat integration network and power plant. Sensitivity and risk analyses were conducted to evaluate the economics, with process yields identified as the most relevant indicators to the minimum selling price (MSP). The analysis revealed a promising cost-competitive range for biographite MSP against fossil-based graphite (medium quality synthetic graphite Chinese market price ~$\$$4.2/kg). Case D, which includes biofuels as a byproduct, presents the best metrics, reaching a MSP of $\$$3.3/kg of anode-grade biographite with a profit margin of 27 %. While including biofuels in the product slate provides the best economic performance, the uncertainty associated with the big capital investment makes its risk 13 % higher to attain an IRR >20 % than the case in which biographite is produced as a standalone product. Overall, this study demonstrates that integrated biorefineries can produce a cost-competitive bio-based anode material for Li-ion batteries.

09 BIOMASS FUELS↗
DOE OSTI2023

Techno-economic assessment and life cycle assessment of three potential pathways for biomass liquefaction

Biomass liquefaction can enhance corn-stover slurry transportation by reducing yield stress and overall viscosity, easing biomass handling, especially for slurries at high solids loading (≥30 % (w/v). Implementing a liquefaction process at the front-end of the biorefinery could reduce downtime caused by equipment fouling. Furthermore, liquefaction reduces process complexity by transforming high fiber mass into a pumpable slurry. Three scenarios for liquefaction of corn stover pellets: enzyme process, enzyme mimetic process, and a combined process of enzyme and enzyme mimetic were assessed. The ideal process will have the best performance-to-cost ratio, with minimal impact on the environment. Techno-economic and life-cycle analyses were used to understand the economic and environmental effects of the three liquefaction scenarios and to determine if one or more can achieve cost parity. Here, results show that the enzyme process had the best performance in terms of cost and emissions (gCO 2 -equivalent/kg slurry)compared to the other scenarios.

09 BIOMASS FUELS↗
DOE OSTI2022

Tradeoffs among indoor air quality, financial costs, and CO 2 emissions for HVAC operation strategies to mitigate indoor virus in U.S. office buildings

Adapting building operation during the COVID-19 pandemic to improve indoor air quality (IAQ) while ensuring sustainable solutions in terms of costs and CO 2 emissions is challenging and limited in literature. Our previous study investigated different HVAC operation strategies, including increased filtration using MERV 10, MERV 13, or HEPA filters, as well as supplying 100% outdoor air into buildings for a system initially sized for MERV 10 filtration. This paper significantly extends that research by systematically analyzing the potential financial and environmental impact for different locations in the U.S. The previous medium office building system model is improved to account for operation in different climates. New evaluation metrics are created to consider the comprehensive impact of improving IAQ on costs and CO 2 emissions, using dynamic emission factors for electricity generation depending on the location. HVAC operation strategies are studied in five different locations across the United States, with distinct climates and electricity sources. In four of the five locations, MERV 13 filtration offers the best improvement in IAQ per increase in costs and emissions relative to MERV 10. The exception is the mildest climate of San Diego, where use of 100% outdoor air provides the best IAQ with a limited increase in costs and emissions. Finally, a system not sized for HEPA filtration can lead to increased costs and emissions without much improvement in IAQ.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Mitigation of spatial nonstationarity with vision transformers

Spatial nonstationarity, the location variance of features’ statistical distributions, is ubiquitous in many natural settings. For example, in geological reservoirs rock matrix porosity varies vertically due to geomechanical compaction trends, in mineral deposits grades vary due to sedimentation and concentration processes, in hydrology rainfall varies due to the atmosphere and topography interactions, and in metallurgy crystalline structures vary due to differential cooling. Conventional geostatistical modeling workflows rely on the assumption of stationarity to be able to model spatial features for geostatistical inference. Nevertheless, this is often not a realistic assumption when dealing with nonstationary spatial data and this has motivated a variety of nonstationary spatial modeling workflows such as trend and residual decomposition, cosimulation with secondary features, and spatial segmentation and independent modeling over stationary subdomains. The advent of deep learning technologies has enabled new workflows for modeling spatial relationships. However, there is a paucity of demonstrated best practice and general guidance on mitigation of spatial nonstationarity with deep learning in the geospatial context. We demonstrate the impact of two common types of geostatistical spatial nonstationarity on deep learning model prediction performance and propose the mitigation of such impacts using self-attention (vision transformer) models. We demonstrate the utility of vision transformers for the mitigation of nonstationarity with relative errors as low as 10%, exceeding the performance of alternative deep learning methods such as convolutional neural networks. We establish best practice by demonstrating the ability of self-attention networks for modeling large-scale spatial relationships in the presence of commonly observed geospatial nonstationarity.

58 GEOSCIENCES↗
DOE OSTI2020

Enhanced NO, CO and C 3 H 6 conversion on Pt/Pd catalysts: Impact of oxygen storage material and catalyst architecture

Simultaneous conversion of NO, CO and C 3 H 6 under stoichiometric conditions was carried out on washcoated monoliths containing oxygen storage material (OSM)-promoted mixed Platinum group metals (PGM: Pt(95 %)/Pd(5 %)), to evaluate OSM promotion and to identify the best architecture. The studied OSMs include ceria-zirconia (Ce 0.3 Zr 0.7 O 2 ; CZO) and mixed metal oxide spinel (Mn 0.5 Fe 2.5 O 4 ; MFO). PGM supported directly on the OSM was found to be the best design for CZO, leading to a ~70 °C simultaneous decrease in the light-off temperature (T 80 ; feed temperature giving 80 % conversion) for NO, CO and C 3 H 6 conversion compared to the alumina-supported PGM. Close coupling between the PGM and CZO is responsible for the activity promotion. In contrast, a dual-layer architecture (top PGM layer, bottom MFO layer) outperformed the MFO-supported PGM catalyst. The dual-layer PGM-MFO catalyst decreased the T 80 by ~50 °C for NO, CO and C 3 H 6 conversion compared to the PGM-only catalyst. Enhancement obtained with the dual-layer PGM-MFO architecture relies on a direct catalytic contribution from the spinel. During lean/rich modulation the addition of CZO or spinel helps to mitigate the detrimental impact of modulation on NO, CO and C 3 H 6 conversion above 400 °C. The data suggest that both CZO and MFO can buffer lean/rich modulation but exhibit preference to different reductants; CZO-supported PGM and dual-layer PGM-MFO show no conversion decrease during modulation for CO or C 3 H 6 modulation, respectively. Dynamic oxygen storage capacity (DOSC) measurements show that the spinel exhibits ~10 times higher DOSC than CZO for both CO and C 3 H 6 reductants. Both CO and C 3 H 6 are equally effective reductants for the MFO but CO is better for CZO and PGM-deposited CZO. The study provides useful insight into benefits of OSM and provides guidance for optimization of the multi-component PGM + OSM catalyst composition and architecture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A systematic multicriteria-based approach to support product portfolio selection in microalgae biorefineries

Here this work proposes and applies a sequential approach of objective methods to aid the decision-making process for the deployment of microalgae biorefineries. The strategy combines Multicriteria Decision Analysis (MCDA) and weight assignment methods to simultaneously consider technical, economic, and environmental criteria to (1) outrank the best bioproduct options from different biomass fractions present in microalgae biomass at different ratios (namely carbohydrates, lipids, and protein) and (2) define the most suitable biorefining pathways associated with specific pairings of microalgae strains and cultivation conditions. The first part of the assessment identified succinic acid, acrylic acid, and citric acid as the top-ranked bioproducts from carbohydrates, polyurethane from lipids, and thermoplastic extrusion co-feed from protein. The second step of the analysis determined that, when production of a hydrocarbon fuel is desired, the compositional profile of a strain is paramount in defining the biorefining setup that should be pursued. In summary, microalgae lipids should be sent to the production of hydrocarbon fuels if the ratio between neutral lipids and fermentable carbohydrates is higher than roughly 1, with carbohydrates and protein being converted to the higher-value products noted above. Finally, this result was corroborated through process simulations, which indicated superior economic and environmental metrics when strains are paired with suitable conversion pathways identified through MCDA based on their compositional profiles. The outcomes of this work provide clear, objective, guidelines for establishing the best biorefining approach for a large suite of biochemical compositions as a screening method prior to employing detailed process simulations alongside rigorous techno-economic and life-cycle assessments.

09 BIOMASS FUELS↗
DOE OSTI2021

Effectiveness of PCE superplasticizers in calcined clay blended cements

Highlights: • Cements containing 0–40 wt% of a calcined clay rich in meta kaolin were studied. • The calcined clay decreases fluidity of the blended cements considerably. • In cement, the calcined clay adsorbs a large amount of Ca{sup 2+} ions. • A common HPEG polycarboxylate superplasticizer fluidizes OPC/CC blends best. • A zwitterionic PCE also fluidizes well and adsorbs in similar amounts as HPEG. The impact of a calcined clay (CC) rich in meta kaolin (~50 wt%) present in composite cements at 0–40% substitution rate for the clinker was studied relative to the dispersing force of different PCE superplasticizers. It was found that CC increases the water demand of the blended cements considerably (+85% for the 60:40 blend vs. neat OPC). Furthermore, PCEs which fluidize OPC best also provide optimal performance in CC blended cements, but require much higher dosages (in OPC/CC 60:40, 4–6 times as compared to neat OPC). In all systems, HPEG-PCE produced superior dispersing performance over anionic MPEG-PCEs. A mechanistic study involving zeta potential measurements revealed that the initially negatively charged calcined clay surface adsorbs huge amounts of Ca{sup 2+} ions from the pore solution, thus facilitating adsorption of anionic PCE superplasticizers. The results signify that commercially available PCE products can effectively fluidize OPC/CC blended cements.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Segmentation of tomography datasets using 3D convolutional neural networks

Dendritic microstructures are ubiquitous in nature and are the primary solidification morphologies in metallic materials. Techniques such as X-ray computed tomography (XCT) have provided new insights into dendritic phase transformation phenomena. However, manual identification of dendritic morphologies in microscopy data can be both labor intensive and potentially ambiguous. The analysis of 3D datasets is particularly challenging due to their large sizes (terabytes) and the presence of artifacts scattered within the imaged volumes. Here, in this study, we trained 3D convolutional neural networks (CNNs) to segment 3D datasets. Three CNN architectures were investigated, including a new version of FCDenseNet which we extended to 3D. We show that using hyperparameter optimization (HPO) and fine-tuning techniques, both 2D and 3D CNN architectures outperform the previous state of the art. The 3D U-Net architecture trained in this study produced the best segmentations according to quantitative metrics (intersection-over-union of 95.56% and a boundary displacement error of 0.58 pixels), while 3D FCDense produced the smoothest boundaries and best segmentations according to visual inspection. The trained 3D CNNs are able to segment entire 852 × 852 × 250 voxel 3D volumes in only ~60 s, thus hastening the progress towards a deeper understanding of phase transformation phenomena such as dendritic solidification.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Parallel derivative-free optimization for simulation-based design of behind-the-meter energy systems

In this work, the integrated design and dispatch of behind-the-meter or distributed resources (e.g. stationary battery storage and solar PV generation) is considered. A simulation-based framework is employed, generating high-fidelity results with closed-loop predictive control at a fine resolution, at the expense of high computational cost (several minutes to a few hours per design point). To address this challenge, parallel derivative-free design methods are considered. Four methods are compared, including state-of-the-art surrogate-based methods (Radial-Basis Functions and Gaussian processes) and sampling strategies, an evolutionary-based method, and a simple sequential grid refinement method. As a case study, two types of design problem with increasing complexity are considered, namely, the design of behind-the-meter resources (three design variables) and the inclusion of grid capacity (four design variables). The second yields a constrained design problem for which violations can only be determined after solving the computationally expensive simulation. For the three-dimensional case, all methods present a good performance, achieving a solution within 1% of the optimum after the first iteration, with the sequential grid refinement exhibiting the fastest convergence and achieving the best final objective value. This indicates that the parallel evaluation of multiple sampling points may be more important than the choice of method for small decision spaces. For the four-dimensional constrained case, the Genetic Algorithm presents the best tradeoff between performance and computational effort, while the rough objective function terrain generated by constraint violation penalties reduces the performance of surrogate-based methods. Contour plots with flat regions indicate flexibility in the optimal design and highlight the importance of characterizing the solution space.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Benchmarking Monte Carlo codes for the modelling of low-energy neutron production target reactions

The increasing adoption of accelerator-based neutron sources (ABNS) for applications including neutron capture therapy (NCT) research has highlighted the need for accurate simulation tools. Precise modelling of the neutron production target is crucial to ensure that simulated predictions of neutron beam characteristics used for subsequent beam shaping assembly design are reliable. This work presents a comprehensive benchmarking of four widely-used Monte Carlo codes - Geant4, PHITS, FLUKA (CERN), and MCNP - for modelling low-energy neutron production target reactions. Using their recommended physics models and cross-section libraries, we evaluate each code’s performance in simulating four beam-target reactions: 7 Li(p,n) 7 Be, 9 Be(p,n) 9 B, 9 Be(d,n) 10 B, and C(d,n)N. Predictions of neutron yield, angular distributions, and energy spectra are compared against available thick target experimental data. Results show varying levels of agreement between the codes depending on the reaction type, energy range, and beam characteristics. Geant4, MCNP and PHITS are the overall best performing codes for the simulation of total neutron yield and yield in the forward direction across most reactions. Across energies where experimental benchmarks exist, inter-code discrepancies in total and forward-directed yield are typically 10 to 30%, with larger deviations at near-threshold incident ion energies. PHITS provides the best overall reproduction of experimental spectra, particularly for the 9 Be(p,n) 9 B reaction. Additionally, PHITS demonstrates superior computational performance for most reactions. These findings provide valuable guidance for ABNS design, highlighting the strengths and limitations of each code for the simulation of low-energy neutron production reactions.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

When physics-informed data analytics outperforms black-box machine learning: A case study in thickness control for additive manufacturing

Aerosol jet printing (AJP) has emerged as a promising noncontact additive manufacturing method for high-resolution printing for a wide range of material systems. A key challenge limiting the broader adoption of AJP in the material science community is the lack of methods to precisely control thickness. Herein, we develop a model-based design of experiment (MBDoE) framework that integrates physics-informed models, nonlinear regression, and information criteria to postulate, select and calibrate the best model to describe and optimize the AJP manufacturing process. Starting with already available data from system commissioning (e.g., prior single variable sensitivity analysis), four candidate physics-informed models are postulated and trained. MBDoE identifies a single additional optimal experiment to validate these predictive models with quantified uncertainties, which are then used to determine the best experimental conditions to control printed film thickness. As a comparative benchmark, the analysis is repeated using the same dataset with nonparametric Gaussian process regression (GPR) model that does not incorporate physical information. Using MBDoE principles, we find that only five experiments are necessary to calibrate the nonlinear physics-informed parametric model, and with said limited data, this model outperforms the black-box machine learning GPR model. This key result underscores an emerging trend in the data science community: incorporating physical information into predictive models often drastically reduces the data requirements. Leveraging MBDoE further increased the data efficiency. By design, the proposed data science framework is general in nature and can be easily extended to other experimental and additive manufacturing systems beyond AJP.

Aerosol jet printing↗
DOE OSTI2020

Removal of Na + and Ca2 + with Prussian blue analogue electrodes for brackish water desalination

Desalination of brackish water sources is critical to addressing the growing global freshwater demand. One promising approach is electrically driven desalination using intercalation electrodes. While intercalation electrodes have been widely researched for energy storage applications, only a small subset of those materials is suitable for desalination. In this work, we report the synthesis, characterization, and in-device testing of three Prussian blue analogue intercalation compounds: copper, manganese, and zinc hexacyanoferrate with formulas K x M[Fe(CN) 6 ] z ·nH 2 O (M = Cu, Mn, Zn). The desalination performance for each of these materials against carbon electrodes is reported for Na + intercalation and for Ca 2+ intercalation using 1000 ppm NaCl and 1000 ppm CaCl 2 feed solutions, respectively. While the copper and manganese analogs showed promising performance for Na + and Ca 2+ intercalation, the zinc compound was unstable and underwent rapid dissolution. Manganese hexacyanoferrate showed the best desalination performance in terms of salt removal capacities and salt removal rates with NaCl while copper hexacyanoferrate performed the best with CaCl 2 . The manganese analog proved to be the most stable intercalation material, retaining 83% and 72% of its salt removal capacity after 280 cycles in NaCl and CaCl 2 feed solutions respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Analytical investigation of the dew point water recovery system with potential application for drinking water production

The article presents the analytical investigation of the Dew Point Water Recovery (DPWR) system with potential application for drinking water production. Four different configurations of the DPWR system were proposed, differing in the number and type of dew point cooling exchangers used, and their operation was described using a validated convective heat transfer coefficient mathematical model. It was found that the three stage configu-ration of the DPWR system with a regenerative exchanger has the best water recovery performance, while the three stage configuration with a counter-flow exchanger has the best ratio of energy supplied to the system in relation to the amount of water produced. It was also found that the DPWR system can operate in a wide range of operating conditions with a specific electric energy consumption reaching below 0.9 kWh/m 3 and GOR in the range of 0.36-2.16. What distinguishes the DPWR system from other methods of drinking water production is the ability to work without an additional source of thermal energy apart from the energy of the air supplied to the system. Thanks to this property, the system has the potential to fill the technological gap of a low-energy and easily accessible method of drinking water production.

42 ENGINEERING↗
DOE OSTI2021

Miscellaneous Electric Loads: Characterization and Energy Savings Potential

Over time, miscellaneous electric loads (MELs) are expected to increase both in magnitude and share of residential and commercial building energy consumption. This trend is most apparent in North America, but it is also occurring in Japan and Europe. However, the contribution of MELs to building energy use is not currently well understood, both because the products in this category are transforming rapidly and the definition and classification of MELs is ambiguous. This study estimated the national energy consumption of 36 MELs using best-available data and found them to comprise 12% of delivered electricity to the U.S. residential and commercial building sectors. If 26 of these MELs were replaced with the most energy-efficient product models available on the market, their energy consumption could be halved to 6% of delivered electricity. National energy models will better account for building energy consumption by incorporating the MELs data collected and analyzed for this study, leading to improved policy decisions.

Miscellaneous electric loads, Plug loads, Taxonomy↗
DOE OSTI2024

China's plug-in hybrid electric vehicle transition: An operational carbon perspective

Assessing the emissions of plug-in hybrid electric vehicle (PHEV) operations is crucial for accelerating the carbon–neutral transition in the passenger car sector. This study is the first to adopt a bottom-up model to measure the real-world energy use and carbon dioxide emissions of China’s top twenty selling PHEV models across different regions from 2020 to 2022. The results indicate that (1) the actual electricity intensity of the best-selling PHEV models (20.2–38.2 kWh/100 km) was 30–40 % higher than the New European Driving Cycle values, and the actual gasoline intensity (4.7–23.5 L/100 km) was 3–6 times greater than the New European Driving Cycle values. (2) The overall energy use of the best-selling models varied among different regions, and the energy use from 2020 to 2022 in Southern China was double that Northern China and the Yangtze River Middle Reach. (3) The top-selling models emitted 4.7 megatons of carbon dioxide nationwide from 2020 to 2022, with 1.9 megatons released by electricity consumption and 2.8 megatons released by gasoline combustion. Furthermore, targeted policy implications for expediting the carbon–neutral transition within the passenger car sector are proposed. In essence, this study explores and compares benchmark data at both the national and regional levels, along with performance metrics associated with PHEV operations. The main objective is to aid nationwide decarbonization efforts, focusing on carbon reduction and promoting the rapid transition of road transportation toward a net-zero carbon future.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Techno-economic implications and cost of forecasting errors in solar PV power production using optimized deep learning models

Accurate solar Photovoltaic (PV) power forecasting is important for enhancing both the performance and economic feasibility of PV systems. This study evaluates several deep learning models, including Dense Neural Networks (DNN), Long Short-Term Memory (LSTM), Convolutional Neural Networks (CNN), and a hybrid LSTMCNN model, for predicting PV power production one day in advance. Prior to optimization, the models exhibited relatively high errors, with the best model (DNN) achieving a Root Mean Square Error (RMSE) of 31.13 kW and a coefficient of determination (R 2 ) of 62.15 %. After employing Bayesian optimization, the LSTM-CNN model demonstrated the best performance, with the RMSE reduced to 9.79 kW and R 2 improved to 97.62 %, showcasing significant enhancement in predictive accuracy. Here, the economic evaluation considered three cases: rewards for underestimation (0.08 USD/kWh), no rewards, and penalties for both over-and underestimation (120 % of the utility tariff). In the rewards scenario, the LSTM-CNN model reduced the Levelized Cost of Electricity (LCOE) by 4 %, while in the penalty scenario, a backup diesel generator would have increased the LCOE by 49 %. Additionally, the LSTM-CNN model minimized financial losses, achieving the lowest penalties and maximizing net cash flow compared to other models, demonstrating its overall technical and economic superiority.

Deep learning↗