Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffuser Flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Development and pilot line production of lithium doped silicon solar cells

The work performed over the period of September 1971 to August 1972 to develop production processes for fabrication of lithium doped P/N cells is described. The BCl3 diffusion without 02 was selected as the optimum diffusion process for fabrication of lithium doped cells. An 8-2-7 (warm up - deposition - drive-in time in minutes) diffusion schedule at 1055 C was used for the first two lots (300 cells each) delivered to JPL. Cell efficiencies ranged from 11.0 to 13.7% based on an AMO of 135.3 mW/sq cm. These high efficiencies were obtained using from 10 to 40 cells per boron diffusion; increasing the quantity beyond 40 resulted in lower outputs. At this point, the emphasis was placed on investigation of a BCl3 with 02 diffusion. Through evaluation of the effects of diffusion time and temperature, gas flow rates, and desposition plus drive-in vs. continuous deposition and no drive-in cycles, diffusion parameters were determined which produced short circuit currents of 136 + or - 4 mA for ten cells spaced along 12 in. of the diffusion boat. The quantity was increased to 60, 100, and 150 cell diffusions with no more variation in cell short circuit current than observed with 10 cells.

Payne, P. A.↗

Nanoscale Hybrid Electrolytes with Viscosity Controlled Using Ionic Stimulus for Electrochemical Energy Conversion and Storage

As renewable energy is rapidly integrated into the grid, the challenge has become storing intermittent renewable electricity. Technologies including flow batteries and CO 2 conversion to dense energy carriers are promising storage options for renewable electricity. To achieve this technological advancement, the development of next generation electrolyte materials that can increase the energy density of flow batteries and combine CO 2 capture and conversion is desired. Liquidlike nanoparticle organic hybrid materials (NOHMs) composed of an inorganic core with a tethered polymeric canopy (e.g., polyetheramine (HPE)) have a capability to bind chemical species of interest including CO 2 and redox-active species. In this study, the unique response of NOHM-I-HPE-based electrolytes to salt addition was investigated, including the effects on solution viscosity and structural configurations of the polymeric canopy, impacting transport behaviors. The addition of 0.1 M NaCl drastically lowered the viscosity of NOHM-based electrolytes by up to 90%, reduced the hydrodynamic diameter of NOHM-I-HPE, and increased its self-diffusion coefficient, while the ionic strength did not alter the behaviors of untethered HPE. This study is the first to fundamentally discern the changes in polymer configurations of NOHMs induced by salt addition and provides a comprehensive understanding of the effect of ionic stimulus on their bulk transport properties and local dynamics. These insights could be ultimately employed to tailor transport properties for a range of electrochemical applications.

25 ENERGY STORAGE↗

Effect of Three Modifications on Performance of Auxiliary-Stage Supercharger for V-1710-93 Engine

Three modifications of the auxiliary-stage supercharger for the V-1710-93 engine were designed and tested as part of an investigation to improve the power output and the altitude performance of the engine. A 12-vane diffuser was substituted for the standard 11-vane diffuser, and a vaneless discharge passage and a modified scroll were designed to increase the flow capacity of the supercharger and thereby to increase the performance at the high volume flows required by the engine. With the 12-vane diffuser installed and the carburetor replaced by an adapter, the equivalent volume flow at the peak efficiency point was increased 25 percent at the lowest speed investigated and 9.5 percent at the highest speed. When the carburetor was used, any increase in equivalent volume flow was masked by choking in the carburetor. A small decrease in the peak adiabatic efficiency resulted from using the 12-vane diffuser. At the high volume flows where the supercharger is required to operate, the performance was improved by the 12-vane diffuser. With the vaneless discharge passage, the surge-free range of the supercharger was increased 35 percent at the lowest tip speed investigated by increasing the maximum air flow. The maximum air flow at high tip speeds was again limited by choking in the carburetor, which masked the effect of the vaneless discharge passage on the maximum air flow. At the high volume flows near the operating point of the supercharger, the performance with the vaneless discharge passage was better than that with the standard 11-vane diffuser. At the low volume flows when the standard 11-vane diffuser gave better performance. The modified scroll gave performance characteristics that were practically the same as those of the standard scroll except at high tip speeds, where the peak performance was improved.

Downing, Richard M.↗

Matrix-Free High-Performance Saddle-Point Solvers for High-Order Problems in \(\boldsymbol{H}(\operatorname{\textbf{div}})\)

Here, this work describes the development of matrix-free GPU-accelerated solvers for high-order finite element problems in H(div). The solvers are applicable to grad-div and Darcy problems in saddle-point formulation, and have applications in radiation diffusion and porous media flow problems, among others. Using the interpolation–histopolation basis, efficient matrix-free preconditioners can be constructed for the (1, 1)-block and Schur complement of the block system. With these approximations, block-preconditioned MINRES converges in a number of iterations that is independent of the mesh size and polynomial degree. The approximate Schur complement takes the form of an M-matrix graph Laplacian and therefore can be well-preconditioned by highly scalable algebraic multigrid methods. High-performance GPU-accelerated algorithms for all components of the solution algorithm are developed, discussed, and benchmarked. Numerical results are presented on a number of challenging test cases, including the “crooked pipe” grad-div problem, the SPE10 reservoir modeling benchmark problem, and a nonlinear radiation diffusion test case.

97 MATHEMATICS AND COMPUTING↗

Analysis of liquid rocket combustion chamber turbulence levels from diffusion data

The intensity of turbulence and the Lagrangian correlation coefficient in a liquid-rocket combustion chamber have been analytically determined from an analysis of experimental diffusion data obtained in a small rocket engine which operated at 300-psia chamber pressure and produced approximately 250 pounds thrust. Results of gas-sample measurements obtained by Orsat and gas-chromatograph techniques to determine helium-concentration profiles were analyzed on the basis of Taylor's (1921) turbulent diffusion theory to obtain turbulence flow-field parameters. The results of the analysis indicate that turbulent diffusion in a combustion chamber can be adequately modeled by the one-dimensional Taylor theory, which assumes that the intensity of turbulence is a function only of axial distance in the chamber and that the Lagrangian correlation coefficient is expressed by a power law. The results indicate a higher intensity of turbulence and lower correlation than previously expected.

Smith, L. O., Jr.↗

Effects of Mean Flow Profiles on Instability of a Low-Density Gas Jet Injected into a High-Density Gas

The objective of this study was to investigate the effects of the mean flow profiles on the instability characteristics in the near-injector region of low-density gas jets injected into high-density ambient gas mediums. To achieve this, a linear temporal stability analysis and a spatio-temporal stability analysis of a low-density round gas jet injected vertically upwards into a high-density ambient gas were performed by assuming three different sets of mean velocity and density profiles. The flow was assumed to be isothermal and locally parallel. Viscous and diffusive effects were ignored. The mean flow parameters were represented as the sum of the mean value and a small normal-mode fluctuation. A second order differential equation governing the pressure disturbance amplitude was derived from the basic conservation equations. The first set of mean velocity and density profiles assumed were those used by Monkewitz and Sohn for investigating absolute instability in hot jets. The second set of velocity and density profiles assumed for this study were the ones used by Lawson. And the third set of mean profiles included a parabolic velocity profile and a hyperbolic tangent density profile. The effects of the inhomogeneous shear layer and the Froude number (signifying the effects of gravity) on the temporal and spatio-temporal results for each set of mean profiles were delineated. Additional information is included in the original extended abstract.

Vedantam, Nanda Kishore↗

Radiant extinction of gaseous diffusion flames

The absence of buoyancy-induced flows in microgravity significantly alters the fundamentals of many combustion processes. Substantial differences between normal-gravity and microgravity flames have been reported during droplet combustion, flame spread over solids, candle flames, and others. These differences are more basic than just in the visible flame shape. Longer residence time and higher concentration of combustion products create a thermochemical environment which changes the flame chemistry. Processes such as flame radiation, that are often ignored under normal gravity, become very important and sometimes even controlling. This is particularly true for conditions at extinction of a microgravity diffusion flame. Under normal-gravity, the buoyant flow, which may be characterized by the strain rate, assists the diffusion process to transport the fuel and oxidizer to the combustion zone and remove the hot combustion products from it. These are essential functions for the survival of the flame which needs fuel and oxidizer. Thus, as the strain rate is increased, the diffusion flame which is 'weak' (reduced burning rate per unit flame area) at low strain rates is initially 'strengthened' and eventually it may be 'blown-out'. Most of the previous research on diffusion flame extinction has been conducted at the high strain rate 'blow-off' limit. The literature substantially lacks information on low strain rate, radiation-induced, extinction of diffusion flames. At the low strain rates encountered in microgravity, flame radiation is enhanced due to: (1) build-up of combustion products in the flame zone which increases the gas radiation, and (2) low strain rates provide sufficient residence time for substantial amounts of soot to form which further increases the flame radiation. It is expected that this radiative heat loss will extinguish the already 'weak' diffusion flame under certain conditions. Identifying these conditions (ambient atmosphere, fuel flow rate, fuel type, etc.) is important for spacecraft fire safety. Thus, the objective is to experimentally and theoretically investigate the radiation-induced extinction of diffusion flames in microgravity and determine the effect of flame radiation on the 'weak' microgravity diffusion flame.

Atreya, Arvind↗

A statistical method for estimating wood thermal diffusivity and probe geometry using in situ heat response curves from sap flow measurements

The heat pulse method is widely used to measure water flux through plants; it works by inferring the velocity of water through a porous medium from the speed at which a heat pulse is propagated through the system. No systematic, non-destructive calibration procedure exists to determine the site-specific parameters necessary for calculating sap velocity, e.g., wood thermal diffusivity and probe spacing. Such parameter calibration is crucial to obtain the correct transpiration flux density from the sap flow measurements at the plant scale; and consequently, to up-scale tree-level water fluxes to canopy and landscape scales. The purpose of this study is to present a statistical framework for estimating the wood thermal diffusivity and probe spacing simutaneously from in-situ heat response curves collected by the implanted probes of a heat ratio apparatus. Conditioned on the time traces of wood temperature following a heat pulse, the parameters are inferred using a Bayesian inversion technique, based on the Markov chain Monte Carlo sampling method. The primary advantage of the proposed methodology is that it does not require known probe spacing or any further intrusive sampling of sapwood. The Bayesian framework also enables direct quantification of uncertainty in estimated sap flow velocity. Experiments using synthetic data show that repeated tests using the same apparatus are essential to obtain reliable and accurate solutions. When applied to field conditions, these tests are conducted during different seasons and automated using the existing data logging system. The seasonality of wood thermal diffusivity is obtained as a by-product of the parameter estimation process, and it is shown to be affected by both moisture content and temperature. Empirical factors are often introduced to account for the influence of non-ideal probe geometry on the estimation of heat pulse velocity, and they are estimated in this study as well. The proposed methodology can be applied for the calibration of existing heat ratio sap flow systems at other sites. It is especially useful when an alternative transpiration calibration device, such as a lysimeter, is not available.

Bayesian inversion↗

Crowded electrolytes containing redoxmers in different states of charge: Solution structure, properties, and fundamental limits on energy density

Nonaqueous redox flow batteries use liquid electrolytes containing redox-active organic molecules (redoxmers) as their energy storage medium. To maximize energy density, the redoxmer concentration needs to be maximized while maintaining low viscosity and high ionic conductivity. During charge, a redoxmer molecule pairs with an ion in the electrolyte while another ion migrates across the membrane to maintain electric neutrality. In a crowded electrolyte, this reconstitution changes physical and chemical properties of the solution. To explore these behaviors, a phenothiazine redoxmer fully miscible with acetonitrile was used, and electrochemical charge was mimicked by chemical oxidation. The solutions were examined using small-angle X-ray scattering, nuclear magnetic resonance, and conductometry and modeled using classical molecular dynamics. Overall, our study indicates that physical and structural properties of redoxmer solutions in both states of charge make it exceedingly difficult to increase the redoxmer concentrations over 2 M at any temperature without compromising dynamic properties of such solutions. The cause for this limitation is proximity to a gel-like regime in which fluidity, diffusivity, and ionic conductivity exponentially decrease with increasing concentration. This tendency is compounded by non-Arrhenius behavior of the electrolyte: a small increase in the concentration outruns gains in fluidity and conductivity at a higher temperature. Thus the properties of crowded electrolytes generally make it impossible to operate when gel-like behavior sets in. Pushing the redoxmer concentration to 2.5-3 M might be possible for small redoxmer molecules, but it would require the use of ionic liquid electrolytes at 340-360 K. (C) 2021 Elsevier B.V. All rights reserved.

25 ENERGY STORAGE↗

Heterogeneous oxidation of amorphous organic aerosol surrogates by O 3 , NO 3 , and OH at typical tropospheric temperatures

Typical tropospheric temperatures render possible phase states of amorphous organic aerosol (OA) particles of solid, semisolid, and liquid. This will affect the multiphase oxidation kinetics involving the organic condensed-phase and gaseous oxidants and radicals. To quantify this effect, we determined the reactive uptake coefficients (γ) of O 3 , NO 3 , and OH by substrate films composed of single and binary OA surrogate species under dry conditions for temperatures from 213 to 313 K. A temperature-controlled coated-wall flow reactor coupled to a chemical ionization mass spectrometer was applied to determine γ with consideration of gas diffusion transport limitation and gas flow entrance effects, which can impact heterogeneous reaction kinetics. The phase state of the organic substrates was probed via the poke-flow technique, allowing the estimation of the substrates' glass transition temperatures. γ values for O 3 and OH uptake to a canola oil substrate, NO 3 uptake to a levoglucosan and a levoglucosan / xylitol substrate, and OH uptake to a glucose and glucose / 1,2,6-hexanetriol substrate have been determined as a function of temperature. We observed the greatest changes in γ with temperature for substrates that experienced the largest changes in viscosity as a result of a solid-to-liquid phase transition. Organic substrates that maintain a semisolid or solid phase state and as such a relatively higher viscosity do not display large variations in heterogeneous reactivity. From 213 to 293 K, γ values of O 3 with canola oil, of NO 3 with a levoglucosan / xylitol mixture, and of OH with a glucose / 1,2,6-hexanetriol mixture and canola oil, increase by about a factor of 34, 3, 2, and 5, respectively, due to a solid-to-liquid phase transition of the substrate. These results demonstrate that the surface and bulk lifetime of the OA surrogate species can significantly increase due to the slowed heterogeneous kinetics when OA species are solid or highly viscous in the middle and upper troposphere. This experimental study will further our understanding of the chemical evolution of OA particles with subsequent important consequences for source apportionment, air quality, and climate.

54 ENVIRONMENTAL SCIENCES↗

Analysis of a dusty wall jet

An analysis is given for the entrainment of dust into a turbulent radial wall jet. Equations are solved based on incompressible flow of a radial wall jet into which dust is entrained from the wall and transported by turbulent diffusion and convection throughout the flow. It is shown that the resulting concentration of dust particles in the flow depends on the difference between the applied shear stress at the surface and the maximum level of shear stress that the surface can withstand (varies as rho(sub d)a(sub g)D) i.e., the pressure due to the weight of a single layer of dust. The analysis is expected to have application to the downflow that results from helicopter and VTOL aircraft.

Lim, Hock-Bin↗

Numerical Simulation of Combustion and Extinction of a Solid Cylinder in Low-Speed Cross Flow

The combustion and extinction behavior of a diffusion flame around a solid fuel cylinder (PMMA) in low-speed forced flow in zero gravity was studied numerically using a quasi-steady gas phase model. This model includes two-dimensional continuity, full Navier Stokes' momentum, energy, and species equations with a one-step overall chemical reaction and second-order finite-rate Arrhenius kinetics. Surface radiation and Arrhenius pyrolysis kinetics are included on the solid fuel surface description and a parameter Phi, representing the percentage of gas-phase conductive heat flux going into the solid, is introduced into the interfacial energy balance boundary condition to complete the description for the quasi-steady gas-phase system. The model was solved numerically using a body-fitted coordinate transformation and the SIMPLE algorithm. The effects of varying freestream velocity and Phi were studied. These parameters have a significant effect on the flame structure and extinction limits. Two flame modes were identified: envelope flame and wake flame. Two kinds of flammability limits were found: quenching at low-flow speeds due to radiative loss and blow-off at high flow speeds due to insufficient gas residence time. A flammability map was constructed showing the existence of maximum Phi above which the solid is not flammable at any freestream velocity.

Tien, J. S.↗

Supersonic flow calculation using a Reynolds-stress and an eddy thermal diffusivity turbulence model

A second-order model for the velocity field and a two-equation model for the temperature field are used to calculate supersonic boundary layers assuming negligible real gas effects. The modeled equations are formulated on the basis of an incompressible assumption and then extended to supersonic flows by invoking Morkovin's hypothesis, which proposes that compressibility effects are completely accounted for by mean density variations alone. In order to calculate the near-wall flow accurately, correction functions are proposed to render the modeled equations asymptotically consistent with the behavior of the exact equations near a wall and, at the same time, display the proper dependence on the molecular Prandtl number. Thus formulated, the near-wall second order turbulence model for heat transfer is applicable to supersonic flows with different Prandtl numbers. The model is validated against flows with different Prandtl numbers and supersonic flows with free-stream Mach numbers as high as 10 and wall temperature ratios as low as 0.3. Among the flow cases considered, the momentum thickness Reynolds number varies from approximately 4,000 to approximately 21,000. Good correlation with measurements of mean velocity, temperature, and its variance is obtained. Discernible improvements in the law-of-the-wall are observed, especially in the range where the big-law applies.

Sommer, T. P.↗

A critical dislocation velocity for serration mechanism transition in a nickel-chromium solid solution alloy

Here, the influence of strain rate across three orders of magnitude (1.70 × 10 –5 /s to 1.43 × 10 –2 /s) along with the effect of the plastic strain accumulation (up to 10%) on the serrated plastic flow were investigated in the nickel-chromium (Ni-Cr) solid solution alloy Nimonic 75 by performing constant-strain-rate tension testing at 600 °C. As the strain rate decreased, the critical strain for the onset of serrations transitioned from normal behavior to inverse behavior. The serrated flow was characterized as Type A+B serration at high strain rate (1.43 × 10 –2 /s). In the intermediate strain-rate regime (1.43 × 10 –3 /s and 1.45 × 10 –4 /s), Type B serrations were observed and followed by a transformation to Type C+B serrations. At the low strain rate (1.70 × 10 –5 /s), the plastic flow immediately displayed Type C serrations, which later evolved into Type C+B serrations. Regardless of the strain rate, plastic strain, or dislocation density, a critical dislocation velocity falling in the range of 1.2 × 10 –6 – 2.2 × 10 –6 m/s was identified to signify the onset of Type C serration, whereby the mobile dislocations break free from the solute cloud for short bursts of deformation. Finally, a novel model by solute rearrangement across dislocation cores was used to understand how the critical dislocation velocity is quantitatively determined by the rate at which solute atoms are able to hop across the glide plane as a partial dislocation core moves through the lattice.

36 MATERIALS SCIENCE↗

Combustion of Two-Component Miscible Droplets in Reduced Gravity

This paper presents recent theoretical and experimental results from an ongoing research program that deals with reduced-gravity combustion of bi-component droplets initially in the mm size range or larger. The primary objectives of the research are to study the effects of droplet internal flows, thermal and solutal Marangoni stresses, and species volatility differences on liquid species transport and overall combustion phenomena (e.g., gas-phase unsteadiness, burning rates, sooting, radiation, and extinction). The research program utilizes a reduced-gravity environment so that buoyancy effects are rendered negligible. Use of large droplets also facilitates visualization of droplet internal flows, which is important to this research. This program is a continuation of extensive ground based experimental and theoretical research on bi-component droplet combustion which has been ongoing for several years. The focal point of this research program is a flight experiment (Bi-Component Droplet Combustion Experiment, BCDCE). This flight experiment is still under development. However, supporting ground studies have been performed, and preliminary data have been obtained from flight experiments (Fiber Supported Droplet Combustion Experiment, FSDC-1 and FSDC-2). These flight experiments were performed during the STS-73/USML-2 and STS-94/MSL- I missions. In the experiments, droplets composed of low- and high-volatility species are burned. The low-volatility components are initially present in small amounts. As combustion of a droplet proceeds, the liquid surface mass fraction of the low-volatility component will increase with time, resulting in a sudden and temporary decrease in droplet burning rates as the droplet rapidly heats to temperatures close to the boiling point of the low-volatility component. This decrease in burning rates causes a sudden and temporary contraction of the flame. The decrease in burning rates and the flame contraction can be observed experimentally. Measurements of burning rates as well as the onset time for flame contraction allow effective liquid-phase species diffusivities to be calculated, e.g., using asymptotic theory. A goal of the research is to relate effective liquid species diffusivities to droplet internal flow characteristics. Droplet internal flows will be visualized in future flight and ground-based experiments.

Shaw, B. D.↗

Sorption and Transport Behavior of {sup 137}Cs, {sup 90}Sr, and {sup 99}Tc on Geological Media in Radioactive Waste Repository, South Korea - 16112

Sorption experiments and a behavior investigation for the radionuclides {sup 137}Cs, {sup 90}Sr, and {sup 99}Tc were conducted using groundwater and solid materials (mud-stone and sandstone) sampled from the Wolsong low- and intermediate-level radioactive waste repository at Gyeongju, Korea. After experiments involving batch sorption, diffusion, and a flow-through column, distribution coefficients (K{sub d}) of the radionuclides were obtained, and sorption properties for each radionuclide were analyzed. Increasing K{sub d} values were observed in the sequence {sup 137}Cs, {sup 90}Sr, and {sup 99}Tc regardless of the geological media tested. For all sorbing radionuclides, K{sub d} values for the mud-stone were observed to be higher than those for sandstone regardless of the groundwater. These higher K{sub d} values are the result of higher levels of total organic carbon in the mud-stone than were present in the sandstone. In addition, the chlorite, kaolinite, and montmorillonite contents in the mud-stone also were higher than in the sandstone. The mineralogical composition of the solid materials was observed to be important in the sorption of sorbing radionuclides. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A method for the temperature calibration of an infrared camera using water as a radiative source

Presented here is an effective low-cost method for the temperature calibration of infrared cameras, for applications in the 0-100 deg. C range. The calibration of image gray level intensity to temperature is achieved by imaging an upwelling flow of water, the temperature of which is measured with a thermistor probe. The upwelling flow is created by a diffuser located below the water surface of a constant temperature water bath. The thermistor probe is kept immediately below the surface, and the distance from the diffuser outlet to the surface is adjusted so that the deformation of the water surface on account of the flow is small, yet the difference between the surface temperature seen by the camera and the bulk temperature measured by the thermistor is also small. The benefit of this method compared to typical calibration procedures is that, without sacrificing the quality of the calibration, relatively expensive commercial blackbodies are replaced by water as the radiative source ({epsilon}{approx_equal}0.98 for the wavelengths considered here). A heat transfer analysis is provided, which improves the accuracy of the calibration method and also provides the user with guidance to further increases in accuracy of the method.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Suppression of Cavity-Driven Flow Separation in a Simulated Mixed Compression Inlet

A test facility designed to simulate a bifurcated subsonic diffuser operating within a mixed compression inlet is described. The subsonic diffuser in this facility modeled a bypass cavity feature often used in mixed compression inlets for engine flow matching and normal shock control. A bypass cavity-driven flow separation was seen to occur in the subsonic diffuser without applied flow control. Flow control in the form of vortex generators and/or a partitioned bypass cavity cover plate were used to eliminate this flow separation, providing a 2% increase in area-averaged total pressure recovery, and a 70% reduction in circumferential distortion intensity.

Wendt, Bruce J.↗