Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite Properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Laboratory for Characterization of Irradiated Graphite

The newly completed Idaho National Laboratory (INL) Carbon Characterization Laboratory (CCL) is located in Labs C19 and C20 of the Idaho National Laboratory Research Center (IRC). The CCL was established under the Next Generation Nuclear Plant (NGNP) Project to support graphite and ceramic composite research and development activities. The research is in support of the Advanced Graphite Creep (AGC) experiment — a major material irradiation experiment within the NGNP Graphite program. The CCL is designed to characterize and test low activated irradiated materials such as high purity graphite, carbon-carbon composites, and silicon-carbide composite materials. The laboratory is fully capable of characterizing material properties for both irradiated and nonirradiated materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Influence of deposition parameters on the microstructure and properties of nitrogen-doped diamondlike carbon films

CN{sub x} films were prepared on cemented carbide substrates by a pulsed bias arc ion-plating method with two graphite targets and using N{sub 2}/Ar mixture gases. The effects of the deposition parameters, such as substrate negative-bias voltage, duty cycle, and nitrogen flow rate, on the structures and properties of CN{sub x} films were investigated using Raman spectra and nanoindentation. The properties of CN{sub x} films are closely related to the film structures. For CN{sub x} films deposited at a different bias voltage, the CN{sub x} film deposited at a bias voltage of -300 V had the highest hardness. The I{sub D}/I{sub G} ratio and G peak position decreased and then increased with increasing bias voltage, and the minimum values, which correspond to the highest sp{sup 3} content, were obtained at a bias voltage of -300 V. For the CN{sub x} films deposited at different duty cycles, the hardness and elastic modulus decreased with increasing duty cycle. For the CN{sub x} films deposited at different nitrogen flow rates, the results show that first the I{sub D}/I{sub G} ratio decreases and sp{sup 3} content increases with increasing nitrogen flow rate, and then the I{sub D}/I{sub G} ratio increases and sp{sup 3} bond content decreases after the nitrogen flow rate exceeds 10 SCCM (SCCM denotes cubic centimeter per minute at STP). The hardness and elastic modulus of the CN{sub x} film prepared at a nitrogen flow rate of 10 SCCM reached the maximum values of 32.1 and 411.8 GPa, respectively.

36 MATERIALS SCIENCE↗

Constraining the Dust Opacity Law in Three Small and Isolated Molecular Clouds

Density profiles of isolated cores derived from thermal dust continuum emission rely on models of dust properties, such as mass opacity, that are poorly constrained. With complementary measures from near-infrared extinction maps, we can assess the reliability of commonly used dust models. In this work, we compare Herschel -derived maps of the optical depth with equivalent maps derived from CFHT WIRCAM near-infrared observations for three isolated cores: CB 68, L 429, and L 1552. We assess the dust opacities provided from four models: OH1a, OH5a, Orm1, and Orm4. Although the consistency of the models differs between the three sources, the results suggest that the optical properties of dust in the envelopes of the cores are best described by either silicate and bare graphite grains (e.g., Orm1) or carbonaceous grains with some coagulation and either thin or no ice mantles (e.g., OH5a). None of the models, however, individually produced the most consistent optical depth maps for every source. The results suggest that either the dust in the cores is not well-described by any one dust property model, the application of the dust models cannot be extended beyond the very center of the cores, or more complex SED fitting functions are necessary.

79 ASTRONOMY AND ASTROPHYSICS↗

Fillers for improved graphite fiber retention by polymer matrix composites

This program was designed to develop technology for fabrication of graphite/epoxy composites containing selected boron and boron-containing fillers, determine the effects of the fillers on physical and mechanical properties of composites, and evaluate the effectiveness of the boron fillers for fiber retention when the composites are exposed to fire conditions followed by impact. Fillers evaluated were crystalline and amorphous boron, boron carbide, and aluminum boride. The fillers were evaluated by mixing with Narmco 5208 resin matrix at quantities up to 5%. Graphite composites were fabricated and evaluated with respect to their mechanical properties, resistance to humidity, and burning characteristics. Also, the mechanism by which the fillers prevented fiber release was studied.

Sheppard, C. H.↗

Exfoliation and Decoration of Graphene Sheets with Silver Nanoparticles and Their Antibacterial Properties

High quality graphene sheets (GRP) have been exfoliated using facile one pot method through direct ultrasonication of graphite in the presence of polyvinyl alcohol. The GRP were decorated with silver nanoparticles (AgNPs) producing graphene–silver nanoparticle composites. The effect of variation of graphite and silver salt mass ratios on the morphology and performance of produced composites was studied. The size of AgNPs decorated on GRP has been tuned with synthesis method optimization. The average size of AgNPs was found to be in the range of 8.6–15.6 nm. Cotton–polyester blend textile fabrics were treated with the new smart developed composite as antibacterial agent producing new composites. A significant inhibition of bacterial growth has been observed for graphene–silver nanoparticle composite and the antibacterial efficiency was optimized. The clear inhibition zone for textiles treated with new developed composite and AgNPs alone was recorded as 12 and 1.75 mm respectively, achieving more than six fold improvement.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Wear resistance and friction reduction in acrylo nitrile butadiene rubber through hybrid combination of graphite flakes and nano tungsten disulphide

Friction and wear have considerable role in the life span of two interacting parts. Incorporation of nanofillers in polymers/elastomers matrix causes commendable changes in its tribologicalproperties. The main purpose of this work is to reduce the coefficient of friction and wear rate of Acrylo Nitrile Butadiene rubber (NBR). To achieve such objective traditionally well knownlubricants graphite(G), tungsten disulphide (WS{sub 2}) and there hybrid combination was incorporated in NBR matrix. Effect of applied load (force) and concentration of fillers on tribological properties of NBR had been studied. The filler incorporation enhanced the hardnessby 8%, showed resistance to hydraulic oil and aging effect also got improved significantly. A particular optimized concentration of NBR with hybrid combination of 2% WS{sub 2} and 4% Graphite showed minimum coefficient of friction as well as wear rate. A hypothesis could be attributed that similar lamellar structure of WS{sub 2} and Graphite along with formation of a stable nanoscale disulfide tribofilmcould result in lowering of friction. These substantially improved properties of nanoreinforced rubber materials would definitely pave promising path for plethora of potential technological applications.

36 MATERIALS SCIENCE↗

Mechanical behavior analysis using small-size graphite disc compression testing with digital image correlation methods

The ASTM International Standard Test Method for Tensile Stress-Strain of Carbon and Graphite (ASTM C749) requires dog-bone shaped specimens. Unfortunately, specimen sizes required in ASTM C749 are much too large for irradiation within a test reactor and are incompatible with irradiation capsule volumes, molten salt degradation facilities, or oxidation apparatus. The ASTM International Standard Test Method for Tensile Strength Estimate by Disc Compression of Manufactured Graphite (ASTM D8289) was developed as an alternative that provides a means for testing tensile properties using smaller specimens when geometric constraints are present. However, the important stress–strain relation throughout the test loading history that could be recorded using ASTM C749 is lost by using ASTM D8289 because of the difficulties involved with using traditional strain gauges or extensometers on such a small specimen. In this work, a digital image correlation (DIC) method, which uses a full-field noncontact surface displacement measurement technique, was applied along with the ASTM D8289 splitting tensile test on eight small samples of graphite grade Mersen 2114 to track their deformation during compressive loading. Initial results showed that the DIC technique can measure the surface displacement/strain on these small (Ø6 × 3 mm) graphite specimens with high accuracy and good repeatability, indicating that the DIC technique, combined with the small-disc splitting tensile test in ASTM D8289, can capture the strain evolution in the test. In conclusion, further comparison of measured strains with analytical and numerical simulation results provides additional understanding of the mechanical behaviour of this nuclear graphite material in complex stress states.

36 MATERIALS SCIENCE↗

Energy loss partitioning during ballistic impact of polymer composites

The objective of this study is to determine the energy dissipation processes in polymer-matrix composites during impact of ballistic projectiles. These processes include heat, fiber deformation and breakage, matrix deformation and fracture, and interfacial delamination. In this study, experimental measurements were made, using specialized specimen designs and test methods, to isolate the energy consumed by each of these processes during impact in the ballistic range. Using these experiments, relationships between material parameters and energy dissipation were examined. Composites with the same matrix but reinforced with Kevlar, PE, and graphite fabric were included in this study. These fibers were selected based on the differences in their intrinsic properties. Matrix cracking was found to be one of the most important energy absorption mechanisms during impact, especially in ductile samples such as Spectra-900 PE and Kevlar-49 reinforced polymer. On the contrary, delamination dominated the energy dissipation in brittle composites such as graphite reinforced materials. The contribution from frictional forces was also investigated and the energy partitioning among the different processes evaluated.

Zee, Ralph H.↗

Graphite Nanoreinforcements for Aerospace Nanocomposites

New advances in the reinforcement of polymer matrix composite materials are critical for advancement of the aerospace industry. Reinforcements are required to have good mechanical and thermal properties, large aspect ratio, excellent adhesion to the matrix, and cost effectiveness. To fulfill the requirements, nanocomposites in which the matrix is filled with nanoscopic reinforcing phases having dimensions typically in the range of 1nm to 100 nm show considerably higher strength and modulus with far lower reinforcement content than their conventional counterparts. Graphite is a layered material whose layers have dimensions in the nanometer range and are held together by weak Van der Waals forces. Once these layers are exfoliated and dispersed in a polymer matrix as nano platelets, they have large aspect ratios. Graphite has an elastic modulus that is equal to the stiffest carbon fiber and 10-15 times that of other inorganic reinforcements, and it is also electrically and thermally conductive. If the appropriate surface treatment can be found for graphite, its exfoliation and dispersion in a polymer matrix will result in a composite with excellent mechanical properties, superior thermal stability, and very good electrical and thermal properties at very low reinforcement loadings.

Drzal, Lawrence T.↗

Interplay of Mechanochemistry and Material Processes in the Graphite to Diamond Phase Transformation

The manifestation of intramolecular strains in covalent systems is widely known to accelerate chemical reactions and open alternative reaction paths. This process is moderately well understood for isolated molecules and unimolecular processes. However, in condensed matter processes such as phase transformations, material properties and structure may influence typical mechanochemical effects. Therefore, we utilize steered molecular dynamics to induce out of plane strains in graphite and compress the system under a constant strain rate to induce phase transformation. We show that the out of plane strain allows phase transformations to initiate at small amounts of compressive strain. Yet, in contrast to typical mechanochemical results, the sum of compressive and out of plane work needed to form a diamond has a local minimum due to altered defect formation processes during phase transformation. Additionally, these altered processes slow the kinetics of the phase transformation, taking longer from initiation to total material transformation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Radionuclide stochastic distribution in the irradiated graphite - 15206

In France, about 17,000 tons of irradiated graphite waste will be produced from the decommissioning of the six gas-cooled nuclear reactors operated by Electricite De France (EDF). Radionuclide measurements in irradiated graphite exhibit very high discrepancies especially when corresponding to precursors at trace level which is often the case for nuclear grade graphite. As evidenced by numerous studies nuclear graphite is a very pure material, however, it cannot be considered from an analytical viewpoint as a typical homogeneous material. Geo-statistics do not give any notable results when the 3D neutron flux and power history are known. Without taking into account the very origin of the stochastic behavior of radionuclide, their properties may be assumed with the statistical properties which are used in the case of contaminated soils but which have no interest for irradiated graphite. At every scale, the huge discrepancy cannot be avoided but can be easily explained by Theory Of Sampling (TOS) of finely divided materials. The complexity of nuclear graphite is due to its high purity. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Band gap formation in graphene by in-situ doping

We report the formation of band gaps in as-grown stacks of epitaxial graphene with opposite doping. Control of in-situ doping during carbon source molecular beam epitaxy growth on SiC was achieved by using different carbon sources. Doping heterostructures were grown by stacking n-type material from a C{sub 60} source on p-type material from a graphite filament source. Activation energies for the resistivity and carrier concentration indicated band gaps up to 200 meV. A photoconductivity threshold was observed in the range of the electrical activation energies. Band gap formation is attributed to electric fields induced by spatially separated ionized dopants of opposite charge.

36 MATERIALS SCIENCE↗

Carbon nanosheet-titania nanocrystal composites from reassembling of exfoliated graphene oxide layers with colloidal titania nanoparticles

Nanoporous composites of carbon nanosheets (CNS) and titania nanoparticles (NPs) were synthesized by reassembling of delaminated graphite oxide (GO) layers with titania clear sol (TCS), and their structural and porous properties were examined by various physico-chemical methods such as XRD, TG/DTA, FT-IR, Raman, FE-SEM/TEM, and low temperature N{sub 2} adsorption. It was found that the facile approach, which utilizes the electrostatic attraction between the negatively charged GO layers and the positively charged TCS particles, leads to a well composed CNS and ultrafine TiO{sub 2} NPs material whose titania amount reaches up to 71 wt%. The titania phase in these composite materials is mainly anatase, which is resistible against high temperature calcination, but also contains a little amount of rutile and brookite depending on synthesis condition. The porosity of the composite is improved and partially affected by the size distributions of TiO{sub 2} NPs. The unique structure, better porosity, and compatible surface affinity of these composites bring about an adsorption concentration-promoted photocatalytic effects toward organic dyes by successfully combining both properties of CNS and titania NPs. - Graphical Abstract: Carbon nanosheet-titania nanocrystal composites can be synthesized by a facile delamination-reassembling method from graphene oxide and colloidal titania. Highlights: Black-Right-Pointing-Pointer A facile delamination-reassembling method for graphene oxide-titania nanocomposite. Black-Right-Pointing-Pointer A nanoporous composite containing mixed phase titania nanocrystals. Black-Right-Pointing-Pointer Partition effect of carbon nanosheets preventing TiO{sub 2} nanoparticles from aggregating. Black-Right-Pointing-Pointer Adsorption concentration-promoted photocatalysis.

36 MATERIALS SCIENCE↗

Fillers for improved graphite fiber retention by polymer matrix composites

The results of a program designed to determine the extent to which elemental boron and boron containing fillers added to the matrix resin of graphite/epoxy composites prevent the release of graphite fibers when the composites are exposed to fire and impact conditions are described. The fillers evaluated were boron, boron carbide and aluminum boride. The conditions evaluated were laboratory simulations of those that could exist in the event of an aircraft crash and burn situation. The baseline (i.e., unfilled) laminates evaluated were prepared from commercially available graphite/epoxy. The baseline and filled laminates' mechanical properties, before and after isothermal and humidity aging, also were compared. It was found that a small amount of graphite fiber was released from the baseline graphite/epoxy laminates during the burn and impact conditions used in this program. However, the extent to which the fibers were released is not considered a severe enough problem to preclude the use of graphite reinforced composites in civil aircraft structure. It also was found that the addition of boron and boron containing fillers to the resin matrix eliminated this fiber release. Mechanical properties of laminates containing the boron and boron containing fillers were lower than those of the baseline laminates. These property degradations for two systems: boron (5 micron) at 2.5 percent filler loading, and boron (5 micron) at 5.0 percent filler loading do not appear severe enough to preclude their use in structural composite applications.

House, E. E.↗

Encapsulation of metal nanoparticles at the surface of a prototypical layered material

Encapsulation of metal nanoparticles just below the surface of a prototypical layered material, graphite, is a recently discovered phenomenon. These encapsulation architectures have potential for tuning the properties of two-dimensional or layered materials, and additional applications might exploit the properties of the encapsulated metal nanoclusters themselves. The encapsulation process produces novel surface nanostructures and can be achieved for a variety of metals. Because these studies of near-surface intercalation are in their infancy, these systems provide a rich area for future studies. This Review presents the current progress on the encapsulation, including experimental strategies and characterization, as well as theoretical understanding which leads to the development of predictive capability. The Review closes with future opportunities where further understanding of the encapsulation is desired to exploit its applications.

encapsulation↗

Enhanced Electrolyte Transport and Kinetics Mitigate Graphite Exfoliation and Li Plating in Fast–Charging Li–Ion Batteries

Despite significant progress in energy retention, lithium-ion batteries (LIBs) face untenable reductions in cycle life under extreme fast-charging (XFC) conditions, which primarily originate from a variety of kinetic limitations between the graphite anode and the electrolyte. Through quantitative Li + loss accounting and comprehensive materials analyses, it is directly observed that the operation of LIB pouch cells at 4 C||C/3 (charging||discharging) results in Li plating, disadvantageous solid-electrolyte-interphase formation, and solvent co-intercalation leading to interstitial decomposition within graphite layers. It is found that these failure modes originate from the insufficient properties of conventional electrolytes, where employing a designed ester-based electrolyte improved the capacity retention of these cells from 55.9% to 88.2% after 500 cycles when operated at the aforementioned conditions. These metrics are the result of effective mitigation of the aforementioned failure modes due to superior Li + transport and desolvation characteristics demonstrated through both experimental and computational characterization. Finally, this work reveals the vital nature of electrolyte design to XFC performance.

25 ENERGY STORAGE↗

Electronic Structures, Bonding Configurations, and Band-Gap-Opening Properties of Graphene Binding with Low-Concentration Fluorine

To better understand the effects of low-level fluorine in graphene-based sensors, first-principles density functional theory (DFT) with van der Waals dispersion interactions has been employed to investigate the structure and impact of fluorine defects on the electrical properties of single-layer graphene films. The results show that both graphite-2H and graphene have zero band gaps. When fluorine bonds to a carbon atom, the carbon atom is pulled slightly above the graphene plane, creating what is referred to as a CF defect. The lowest-binding energy state is found to correspond to two CF defects on nearest neighbor sites, with one fluorine above the carbon plane and the other below the plane. Overall this has the effect of buckling the graphene. The results further show that the addition of fluorine to graphene leads to the formation of an energy band (BF) near the Fermi level, contributed mainly from the 2p orbitals of fluorine with a small contribution from the porbitals of the carbon. Among the 11 binding configurations studied, our results show that only in two cases does the BF serve as a conduction band and open a band gap of 0.37 eV and 0.24 eV respectively. The binding energy decreases with decreasing fluorine concentration due to the interaction between neighboring fluorine atoms. The obtained results are useful for sensor development and nanoelectronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Friction, wear, and noise of slip ring and brush contacts for synchronous satellite use.

A program is being conducted for testing of slip rings for synchronous orbit application. Instrumentation systems necessary for monitoring electrical noise, friction, and brush wear at atmospheric pressure and at less than 50 nanotorr have been developed. A multiplex scheme necessary for the simultaneous recording of brush displacement, friction, and electrical noise has also been developed. Composite brushes consisting of silver-molybdenum disulfide-graphite and silver-niobium diselenide-graphite have been employed on rings of coin silver and rhodium plate. Brush property measurements made included measurement of density, electrical resistivity, shear strength, and microstructure.

Lewis, N. E.↗