Search NASA⌕ Search

SEARCH · Search NASA

Results for “Panel method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Large amplitude flutter of a low aspect ratio panel at low supersonic speeds comparison of theory and experiment

Flutter boundaries, as well as flutter limit cycle amplitudes, frequencies and stresses were computed for a panel of length-width ratio 4.48 exposed to applied in-plane and transverse loads. The Mach number range was 1.1 to 1.4. The method used involved direct numerical integration of modal equations of motion derived from the nonlinear plate equations of von Karman, coupled with linearized potential flow aerodynamic theory. The flutter boundaries agreed reasonably well with experiment, except when the in-plane loading approached the buckling load. Structural damping had to be introduced, to produce frequencies comparable to the experimental values. Attempts to compute panel deflections or stress at a given point met with limited success. There is some evidence, however, that deflection and stress maxima can be estimated with somewhat greater accuracy.

Ventres, C. S.↗
NASA NTRS1973

Parametric analysis of ATM solar array.

The paper discusses the methods used for the calculation of ATM solar array performance characteristics and provides the parametric analysis of solar panels used in SKYLAB. To predict the solar array performance under conditions other than test conditions, a mathematical model has been developed. Four computer programs have been used to convert the solar simulator test data to the parametric curves. The first performs module summations, the second determines average solar cell characteristics which will cause a mathematical model to generate a curve matching the test data, the third is a polynomial fit program which determines the polynomial equations for the solar cell characteristics versus temperature, and the fourth program uses the polynomial coefficients generated by the polynomial curve fit program to generate the parametric data.

Singh, B. K.↗
NASA NTRS1976

Airframe self-noise: Four years of research

A critical assessment of the state of the art in airframe self-noise is presented. Full-scale data on the intensity, spectra and directivity of this noise source are evaluated in the light of the comprehensive theory developed by Ffowcs-Williams and Hawkins. Vibration of panels on commercial aircraft is identified as a possible additional source of airframe noise. The present understanding and methods for prediction of other component sources - airfoils, struts, and cavities - are discussed, and areas for further research as well as potential methods for airframe noise reduction are identified. Finally, the various experimental methods which have been developed for airframe noise research are discussed and sample results are presented.

Hardin, J. C.↗
NASA NTRS1976

Airframe noise: A design and operating problem

A critical assessment of the state of the art in airframe noise is presented. Full-scale data on the intensity, spectra, and directivity of this noise source are evaluated in light of the comprehensive theory developed by Ffowcs Williams and Hawkings. Vibration of panels on the aircraft is identified as a possible additional source of airframe noise. The present understanding and methods for prediction of other component sources - airfoils, struts, and cavities - are discussed. Operating problems associated with airframe noise as well as potential design methods for airframe noise reduction are identified.

Hardin, J. C.↗
NASA NTRS1977

Airplane self-noise - four years of research

A critical assessment of the state of the art in airframe self-noise is presented. Full-scale data on the intensity, spectra, and directivity of this noise source are evaluated. Vibration of panels on the aircraft is identified as a possible additional source of airframe noise. The present understanding and methods for prediction of other component sources (airfoils, struts, and cavities) are discussed, and areas for further research as well as potential methods for airframe noise reduction are identified. Various experimental methods which have been developed for airframe noise research are discussed, and sample results are presented.

Hardin, J. C.↗
NASA NTRS1979

A program to compute three-dimensional subsonic unsteady aerodynamic characteristics using the doublet lattice method, L216 (DUBFLEX). Volume 2: Supplemental system design and maintenance document

The information necessary for execution of the digital computer program L216 on the CDC 6600 is described. L216 characteristics are based on the doublet lattice method. Arbitrary aerodynamic configurations may be represented with combinations of nonplanar lifting surfaces composed of finite constant pressure panel elements, and axially summetric slender bodies composed of constant pressure line elements. Program input consists of configuration geometry, aerodynamic parameters, and modal data; output includes element geometry, pressure difference distributions, integrated aerodynamic coefficients, stability derivatives, generalized aerodynamic forces, and aerodynamic influence coefficient matrices. Optionally, modal data may be input on magnetic field (tape or disk), and certain geometric and aerodynamic output may be saved for subsequent use.

Harrison, B. A.↗
NASA NTRS1986

Nonlinear response - A time domain approach

The present paper reviews the basic concepts of nonlinear response of panels to surface flow and acoustic pressures, simulation of random processes, time domain solutions and the Monte Carlo Method. Applications of this procedure to the orbit-on-demand space vehicles, acoustic fatigue and composite materials are discussed. Numerical examples are included for a variety of nonlinear problems to illustrate the applicability of this method.

Vaicaitis, R.↗
NASA NTRS1986

Laminar flow control perforated wing panel development

Many structural concepts for a wing leading edge laminar flow control hybrid panel were analytically investigated. After many small, medium, and large tests, the selected design was verified. New analytic methods were developed to combine porous titanium sheet bonded to a substructure of fiberglass and carbon/epoxy cloth. At -65 and +160 F test conditions, the critical bond of the porous titanium to the composite failed at lower than anticipated test loads. New cure cycles, design improvements, and test improvements significantly improved the strength and reduced the deflections from thermal and lateral loadings. The wave tolerance limits for turbulence were not exceeded. Consideration of the beam column midbay deflections from the combinations of the axial and lateral loadings and thermal bowing at -65 F, room temperature, and +160 F were included. Many lap shear tests were performed at several cure cycles. Results indicate that sufficient verification was obtained to fabricate a demonstration vehicle.

Fischler, J. E.↗
NASA NTRS1994

Proceedings of the Non-Linear Aero Prediction Requirements Workshop

The purpose of the Non-Linear Aero Prediction Requirements Workshop, held at NASA Langley Research Center on 8-9 Dec. 1993, was to identify and articulate requirements for non-linear aero prediction capabilities during conceptual/preliminary design. The attendees included engineers from industry, government, and academia in a variety of aerospace disciplines, such as advanced design, aerodynamic performance analysis, aero methods development, flight controls, and experimental and theoretical aerodynamics. Presentations by industry and government organizations were followed by panel discussions. This report contains copies of the presentations and the results of the panel discussions.

Logan, Michael J.↗
NASA NTRS1993

Design and performance oof space station photovoltaic radiators

The design and performance of the Space Station Freedom Photovoltaic (PV) Power Module Thermal Control System radiators is presented. The PV Radiator is of a single phase pumped loop design using liquid ammonia as the coolant. Key design features are described, including the base structure, deployment mechanism, radiator panels, and two independent coolant loops. The basis for a specific mass of 7.8 kg/sqm is discussed, and methods of lowering this number for future systems are briefly described. Key performance paramters are also addressed. A summary of test results and analysis is presented to illustrate the survivability of the radiator in the micrometeoroid and orbital debris environment. A design criterion of 95% probability of no penetration of both fluid loops over a 10 year period is shown to be met. Methods of increasing the radiator survivability even further are presented. Thermal performance is also discussed, including a comparison of modeling predictions with existing test results. Degradation in thermal performance due to exposure to atomic oxygen and ultraviolet radiation in the low Earth orbit environment is presented. The structural criteria to which the radiator is designed are also briefly addressed. Finally, potential design improvements are discussed.

White, K. Alan↗
NASA NTRS2003

Fiber Reinforcement Architectures of PMCs on the Hygrothermal-Mechanical Performance for Aeropropulsion Applications

A rigid lightweight sandwich support structure, for the combustor chamber of a new generation liquid propellant rocket engine, was designed and fabricated using Polymer Matric Composite (PMC) facesheet on a Ti honeycomb or Carbon foam core. The facesheet consisted of high stiffness carbon fiber, M40JB, and high temperature Polyimides, such as PMR-11-50 and HFPE-II. Six different fiber architectures; 4HS woven fabric, uni-fabric, woven-uni hybrid, stitched woven fabric, stitched uni-fabric and tri-axial braided structures have been investigated for optimum stiffness-thickness-weight-performance design criteria for the hygrothermal-mechanical propulsion service exposure conditions including rapid heating up to 200 F/sec, maximum operating temperature of 600 F, internal pressure up to 100 psi. An extensive property and performance database including dry-wet mechanical properties at both 25 F and 600 F in various loading modes, thermal and physical properties including blistering onset condition was developed for fiber architecture down-selection and design guidelines. Various optimized process methods including vacuum bag compression molding, solvent assistant RTM (SaRTM), resin film infusion (RFI) were utilized for PMC panel fabrication depending on the architecture type. In the case of stitched woven fabric architecture, the optimal stitch pattern was chosen in terms of stitch density and yarn size, based on both in-plane mechanical properties and blistering performance. Potential reduction of the in-plane properties transverse to the line of stitching was also evaluated. Attempt to correlate the experimental results with theoretical micro-mechanics predictions will be presented.

Shin, Eugene↗
NASA NTRS2007

Hypervelocity Impact (HVI): WLE High Fidelity Specimen RCC16R - Volume 7

During 2003 and 2004, the Johnson Space Center's White Sands Testing Facility in Las Cruces, New Mexico conducted hypervelocity impact tests on the space shuttle wing leading edge. Hypervelocity impact tests were conducted to determine if Micro-Meteoroid/Orbital Debris impacts could be reliably detected and located using simple passive ultrasonic methods. The objective of Target RCC16R was to study hypervelocity impacts through the reinforced carbon-carbon (RCC) panels of the Wing Leading Edge. Impact damage was detected using lightweight, low power instrumentation capable of being used in flight.

Gorman, Michael R.↗
NASA NTRSDate not supplied

Manufacture of Hybrid Standard-Ply/Thin-Ply Carbon/Epoxy Panels for Notched Test Specimens

Weight is a critical metric for aerospace structures, and one possible way to reduce weight is to improve performance using hybrid standard-ply/thin-ply laminates from a single material system. Previous studies showed benefits for stiffness, strength, reduced damage after impact, and increased compression-after-impact strength for these hybrid laminates. Another study suggested that performance of compression-loaded notched hybrid laminate specimens performed better than standard-ply laminates under compression, but the standard-ply laminates performed better under tension loading. However, analysis predicted the failure load and mode better for the hybrid laminates. An analytical study determined several hybrid laminate designs to use in a follow-on testing regiment that is planned to further study the notched hybrid composite performance under compression and tension load. Described herein is a manufacturing method to efficiently manufacture hybrid laminates using automated fiber placement using a 16-tow head where 8 tows are standard-ply and 8 tows are thin-ply. The method saves time in that it eliminates the need to change spools of material when switching from standard-ply to thin-ply lamina, and reduces the waste associated with changing of spools. The method is ideal for small manufacturing operations or research facilities that have only a single head, and the method was successfully applied at the NASA Langley Research Center (LaRC) Integrated Structural Assembly of Advanced Composites (ISAAC) facility to manufacture nine panels that will be used for the follow-on notched specimen testing of hybrid and standard laminates.

composite↗
NASA NTRSDate not supplied

Manufacture of Hybrid Standard-Ply/Thin-Ply Carbon/Epoxy Panels for Notched Test Specimens

Weight is a critical metric for aerospace structures, and one possible way to reduce weight is to improve performance using hybrid standard-ply/thin-ply laminates from a single material system. Previous studies showed benefits for stiffness, strength, reduced damage after impact, and increased compression-after-impact strength for these hybrid laminates. Another study suggested that performance of compression-loaded notched hybrid laminate specimens performed better than standard-ply laminates under compression, but the standard-ply laminates performed better under tension loading. However, analysis predicted the failure load and mode better for the hybrid laminates. An analytical study determined several hybrid laminate designs to use in a follow-on testing regiment that is planned to further study the notched hybrid composite performance under compression and tension load. Described herein is a manufacturing method to efficiently manufacture hybrid laminates using automated fiber placement using a 16-tow head where 8 tows are standard-ply and 8 tows are thin-ply. The method saves time in that it eliminates the need to change spools of material when switching from standard-ply to thin-ply lamina, and reduces the waste associated with changing of spools. The method is ideal for small manufacturing operations or research facilities that have only a single head, and the method was successfully applied at the NASA Langley Research Center (LaRC) Integrated Structural Assembly of Advanced Composites (ISAAC) facility to manufacture nine panels that will be used for the follow-on notched specimen testing of hybrid and standard laminates.

composite↗
NASA NTRS2017

Transparent Conductive Ink for Additive Manufacturing

NASA analyzes, tests, packages, and fabricates electrical, electronic, and electromechanical (EEE) parts. Nanotechnology is listed in NASA's Technology Roadmap as a key area to invest for further development.1 This research project focused on using nanotechnology to improve electroluminescent lighting in terms of additive manufacturing and to increase energy efficiency. Specifically, this project's goal was to produce a conductive but transparent printable ink that can be sprayed on any surface for use as one of the electrodes in electroluminescent device design. This innovative work is known as thick film dielectric electroluminescent (TDEL) technology. TDEL devices are used for "backlighting, illumination, and identification due to their tunable color output, scalability, and efficiency" (I.K. Small, T.D. Rolin, and A.D. Shields, "3D Printed Electroluminescent Light Panels," NASA Fiscal Year 2017 Center Innovation Fund Proposal, unpublished data, 2017). These devices use a 'front-to-back' printing method, where the substrate is the transparent layer, and the dielectric and phosphor are layered on top. This project is a first step in the process of creating a 3D printable 'back-to-front' electroluminescent device. Back-to-front 3D-printed devices are beneficial because they can be printed onto different substrates and embedded in different surfaces, and the substrate is not required to be transparent, all because the light is emitted from the top surface through the transparent conductor. Advances in this area will help further development of printing TDEL devices on an array of different surfaces. Figure 1 demonstrates the layering of the two electrodes that are aligned in a parallel plate capacitor structure (I.K. Small, T.D. Rolin, and A.D. Shields, "3D Printed Electroluminescent Light Panels," NASA Fiscal Year 2017 Center Innovation Fund Proposal, unpublished data, 2017). Voltage is applied across the device, and the subsequent electron excitation results in light emission at the top layer.

Patlan, X. J.↗
NASA NTRS1992

Advanced propulsion for LEO-Moon transport. 1: A method for evaluating advanced propulsion performance

This report describes a study to evaluate the benefits of advanced propulsion technologies for transporting materials between low Earth orbit and the Moon. A relatively conventional reference transportation system, and several other systems, each of which includes one advanced technology component, are compared in terms of how well they perform a chosen mission objective. The evaluation method is based on a pairwise life-cycle cost comparison of each of the advanced systems with the reference system. Somewhat novel and economically important features of the procedure are the inclusion not only of mass payback ratios based on Earth launch costs, but also of repair and capital acquisition costs, and of adjustments in the latter to reflect the technological maturity of the advanced technologies. The required input information is developed by panels of experts. The overall scope and approach of the study are presented in the introduction. The bulk of the paper describes the evaluation method; the reference system and an advanced transportation system, including a spinning tether in an eccentric Earth orbit, are used to illustrate it.

Stern, Martin O.↗
NASA NTRS2010

Climate Benchmark Missions: CLARREO

CLARREO (Climate Absolute Radiance and Refractivity Observatory) is one of the four Tier 1 missions recommended by the recent NRC decadal survey report on Earth Science and Applications from Space (NRC, 2007). The CLARREO mission addresses the need to rigorously observe climate change on decade time scales and to use decadal change observations as the most critical method to determine the accuracy of climate change projections such as those used in the Fourth Assessment Report of the Intergovernmental Panel on Climate Change (IPCC AR4). A rigorously known accuracy of both decadal change observations as well as climate projections is critical in order to enable sound policy decisions. The CLARREO mission accomplishes this critical objective through highly accurate and SI traceable decadal change observations sensitive to many of the key uncertainties in climate radiative forcings, responses, and feedbacks that in turn drive uncertainty in current climate model projections. The same uncertainties also lead to uncertainty in attribution of climate change to anthropogenic forcing. The CLARREO breakthrough in decadal climate change observations is to achieve the required levels of accuracy and traceability to SI standards for a set of observations sensitive to a wide range of key decadal change variables. These accuracy levels are determined both by the projected decadal changes as well as by the background natural variability that such signals must be detected against. The accuracy for decadal change traceability to SI standards includes uncertainties of calibration, sampling, and analysis methods. Unlike most other missions, all of the CLARREO requirements are judged not by instantaneous accuracy, but instead by accuracy in large time/space scale average decadal changes. Given the focus on decadal climate change, the NRC Decadal Survey concluded that the single most critical issue for decadal change observations was their lack of accuracy and low confidence in observing the small but critical climate change signals. CLARREO is the recommended attack on this challenge, and builds on the last decade of climate observation advances in the Earth Observing System as well as metrological advances at NIST (National Institute of Standards and Technology) and other standards laboratories.

Wielicki, Bruce A.↗