Search NASA⌕ Search

SEARCH · Search NASA

Results for “Science activities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

B-site substitutions in LaNb{sub 1-x}M{sub x}O{sub 4-{delta}} materials in the search for potential proton conductors (M=Ga, Ge, Si, B, Ti, Zr, P, Al)

The solid solubilities of potential B-site dopants in LaNb{sub 1-x}M{sub x}O{sub 4-{delta},} materials, M=Ga, Ge, Si, Al, B, P, Zr or Ti, have been investigated in the search for possible novel proton conductors. In general, the solubility levels of these cations were found to be very low (x{<=}0.03). At the maximum value x=0.03, only compositions containing Ti, Ge, Ga and Si appeared pure at the limit of resolution of XRD. The literature phase diagram, La{sub 2}O{sub 3}-Nb{sub 2}O{sub 5}-ZrO{sub 2}, has been re-analysed for compositions of low Zr-content around the composition LaNbO{sub 4}. The electrical properties of phase pure Ti-doped compositions have been studied. Higher bulk and total conductivities were observed in wet than dry conditions, suggesting a significant protonic contribution to total conductivity. In wet conditions, the activation energy for bulk conductivity of LaNb{sub 0.98}Ti{sub 0.02}O{sub 4-{delta}} was found to be much higher than that of an A-site, Sr-doped material, Sr{sub 0.02}La{sub 0.98}NbO{sub 4-{delta},} of similar acceptor dopant concentration. The Sr-doped composition offered higher conductivities than the Ti-doped composition up to approximately 900{sup o}C. -- Graphical abstract: Comparison of total (open symbols) and bulk (closed symbols) conductivities measured in wet (p(H{sub 2}O){approx}0.026 atm.) nitrogen and oxygen atmospheres for LaNb{sub 0.98}Ti{sub 0.02}O{sub 4-{delta}} (LNT2O) and Sr{sub 0.02}La{sub 0.98}NbO{sub 4-{delta}} (S2LNO) materials. Display Omitted Research highlights: {yields} The article investigates solid solubilities of potential B-site dopants in the potential proton conductor LaNb{sub 1-x}M{sub x}O{sub 4-{delta},} {yields} The literature phase diagram, La{sub 2}O{sub 3}-Nb{sub 2}O{sub 5}-ZrO{sub 2}, has been corrected for compositions of low Zr-content around the composition LaNbO{sub 4}. {yields} The electrical properties of Ti-doped compositions have been assessed in wet and dry conditions. {yields} Comparison has been made between the electrical properties of B-site, Ti-doped, compositions and A-site, Sr-doped, compositions.

36 MATERIALS SCIENCE↗

Mechanistic Study of Lead Adsorption on Activated Carbon

Activated carbon (AC) is a carbonaceous material broadly applied in filters to remove lead (Pb(II)) from drinking water through adsorption. However, the chemical interactions between Pb(II) and the reactive sites on AC or other carbonaceous materials are not well understood, yet. The understanding of the mechanism of Pb(II) adsorption onto AC would allow to optimally design AC-based materials even in the presence of a complex liquid phase. Here in this paper, the interaction between Pb(II) and functional groups on AC was investigated at the molecular scale to help identifying the chemical reactions at the solid-liquid interface. Spectroscopic analyses and chemical quantum calculations were performed and indicated the formation of monodentate mononuclear Pb(II)-phenol and bidentate mononuclear Pb(II)-carboxyl complexes on AC. Competitive adsorption behavior was observed between Pb(II) and calcium (Ca(II)) because of their similar adsorption configurations on AC. In contrast, anions, including sulfate and phosphate, were observed to enhance Pb(II) adsorption on AC by forming ternary complexes. On the basis of these observations, a new surface complexation model of Pb(II) adsorption onto AC was formulated and validated with batch tests. Overall, this work presents a new set of chemical reactions at the solid-liquid interface between Pb(II) and AC under various conditions of interest for the application of AC or other carbonaceous materials in water treatment.

36 MATERIALS SCIENCE↗

USING A NEW FINITE SLIT PORE MODEL FOR NLDFT ANALYSIS OF CARBON PORE STRUCTURE

In this work, we present a model for analyzing activated carbon micropore structures based on graphene sheet walls of finite thickness and extent. This is a two-dimensional modification of the widely used infinite slit pore model that assumes graphite-like infinitely extended pore walls. The proposed model has two versions: (1) a strip pore constructed with graphene strip walls that have finite length L in the x direction and are infinite in the y direction. Strip pores are open on both sides in the x direction. (2) A channel pore is a strip pore partially closed along one edge by a perpendicularly oriented graphene wall. This more realistic model allows pore termination via both physical pore entrances and pore blockage. The model consequently introduces heterogeneity of the adsorption potential that is reduced near pore entrances and enhanced near corners of pore walls. These energetically heterogeneous structures fill with adsorbate more gradually than homogeneous pores of the same width. As a result, the calculated adsorption isotherms are smoother and less steep for the finite versus the infinite pore model. In the application of this model for carbon characterization it is necessary to make an assumption about the pore length. In this work we made this assumption based on the high resolution scanning transmission electron microscopy (STEM) results. We find the agreement between the experiment and the model significantly better for the finite than for the infinite pore model.

54 ENVIRONMENTAL SCIENCES↗

Effects of aging and oxidation of palladized iron embedded in activated carbon on the dechlorination of 2-chlorobiphenyl

Reactive activated carbon (RAC) impregnated with palladized iron has been developed to effectively treat polychlorinated biphenyls (PCBs) in the environment by coupling adsorption and dechlorination of PCBs. In this study, we addressed the dechlorination reactivity and capacity of RAC toward aqueous 2-chlorobiphenyl (2-ClBP), and its aging and longevity under various oxidizing environments. RAC containing 14.4% Fe and 0.68% Pd used in this study could adsorb 122.6 mg 2-ClBP/g RAC, and dechlorinate 56.5 mg 2-ClBP/g RAC which corresponds to 12% (yield) of its estimated dechlorination capacity. Due to Fe0 oxidation to form oxide passivating layers, Fe{sub 2}O{sub 3}/Fe{sub 3}O{sub 4} (oxide-water interface) and FeOOH/FeO (oxide-metal interface), RAC reactivity decreased progressively over aging under N{sub 2} < H{sub 2}O + N{sub 2} < H{sub 2}O + O{sub 2} conditions. Considering nanoscale Fe/Pd corrosion chemistry, the decline was quite slow at only 5.6%, 19.5%, and 32.5% over one year, respectively. Dissolved oxygen played a crucial role in enhancing 2-ClBP adsorption but inhibiting its dechlorination. The reactivity change could be explained with the properties of the aged RAC including surface area, Fe0 content, and Fe species. During the aging and oxidation, the RAC showed limited dissolution of Fe and Pd. Finally, implementation issues regarding application of RAC system to contaminated sites are discussed. 25 refs., 6 figs., 1 tab.

01 COAL, LIGNITE, AND PEAT↗

Radon Fluxes from an Earthen Barrier Over Uranium Mill Tailings After Two Decades of Service - 17234

Radon (Rn) fluxes were measured at a disposal facility for uranium mill tailings after two decades of service. The facility was closed with an earthen cover vegetated with grasses. Measurements were made on the surface of the Rn barrier and directly on the surface of the tailings. Fluxes were measured using extra small (area = 0.018 m{sup 2}), small (0.071 m{sup 2}), medium (0.59 m{sup 2}), and large (2.32 m{sup 2}) flux chambers to evaluate the impact of measurement scale on Rn flux. Activated carbon (AC) passive collectors and electric radon detectors (RAD7) were used to measure Rn concentrations. Tests were conducted at various locations on each cover representing conditions that can lead to different levels of soil structural development and different water content. Rn fluxes at the surface of the Rn barrier were much lower than Rn fluxes measured at the surface of the tailings, indicating the barrier remained effective for Rn containment. Geometric mean Rn fluxes measured at the surface of the Rn barrier in each test pit were below the regulatory requirement (0.74 Bq/m{sup 2}- s). Rn concentrations measured using AC samplers in the flux chambers were 60% of concentrations measured using the RAD7, on average, and Rn fluxes computed with the AC data were 9% of those computed with the RAD7 data, on average. Size of the flux chamber had no systematic effect on Rn flux, indicating that 20 y of soil forming processes had not created a pore network causing scale-dependent Rn flux. Geometric mean Rn fluxes in the test pits were similar regardless of differences in surface conditions (vegetation, thickness of soil cover) known to influence soil forming processes and soil structure, but were lower in areas where surface conditions promoted higher water content in the Rn barrier. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Global synthesis of the temperature sensitivity of leaf litter breakdown in streams and rivers

Streams and rivers are important conduits of terrestrially derived carbon (C) to atmospheric and marine reservoirs. Leaf litter breakdown rates are expected to increase as water temperatures rise in response to climate change. The magnitude of increase in breakdown rates is uncertain, given differences in litter quality and microbial and detritivore community responses to temperature, factors that can influence the apparent temperature sensitivity of breakdown and the relative proportion of C lost to the atmosphere vs. stored or transported downstream. We synthesized 1025 records of litter breakdown in streams and rivers to quantify its temperature sensitivity, as measured by the activation energy (Ea, in eV). Temperature sensitivity of litter breakdown varied among twelve plant genera for which Ea could be calculated. Higher values of Ea were correlated with lower-quality litter, but these correlations were influenced by a single, N-fixing genus (Alnus). Ea values converged when genera were classified into three breakdown rate categories, potentially due to continual water availability in streams and rivers modulating the influence of leaf chemistry on breakdown. Across all data representing 85 plant genera, the Ea was 0.34 ± 0.04 eV, or approximately half the value (0.65 eV) predicted by metabolic theory. Our results indicate that average breakdown rates may increase by 5–21% with a 1–4 °C rise in water temperature, rather than a 10–45% increase expected, according to metabolic theory. Differential warming of tropical and temperate biomes could result in a similar proportional increase in breakdown rates, despite variation in Ea values for these regions (0.75 ± 0.13 eV and 0.27 ± 0.05 eV, respectively). The relative proportions of gaseous C loss and organic matter transport downstream should not change with rising temperature given that Ea values for breakdown mediated by microbes alone and microbes plus detritivores were similar at the global scale.

54 ENVIRONMENTAL SCIENCES↗

Tropospheric aerosols over the western North Atlantic Ocean during the winter and summer deployments of ACTIVATE 2020: life cycle, transport, and distribution

The Aerosol Cloud meTeorology Interactions oVer the western ATlantic Experiment (ACTIVATE) is a NASA mission to characterize aerosol–cloud interactions over the western North Atlantic Ocean (WNAO). Such characterization requires understanding of life cycle, composition, transport pathways, and distribution of aerosols over the WNAO. This study uses the GEOS-Chem model to simulate aerosol distributions and properties that are evaluated against aircraft, ground-based, and satellite observations during the winter and summer field deployments in 2020 of ACTIVATE. Transport in the boundary layer (BL) behind cold fronts was a major mechanism for the North American continental outflow of pollution to the WNAO in winter. Turbulent mixing was the main driver for the upward transport of sea salt within and ventilation out of BL in winter. The BL aerosol composition was dominated by sea salt, which increased in the summer, followed by organics and sulfate. Aircraft in situ aerosol measurements provided useful constraints on wet scavenging in GEOS-Chem. The model generally captured observed features such as continental outflow, land–ocean gradient, and mixing of anthropogenic aerosols with sea salt. Model sensitivity experiments with elevated smoke injection heights to the mid-troposphere (versus within BL) better reproduced observations of smoke aerosols from the western US wildfires over the WNAO in the summer. Model analysis suggests strong hygroscopic growth of sea salt particles and their seeding of marine BL clouds over the WNAO (< 35° N). Future modeling efforts should focus on improving parameterizations for aerosol wet scavenging, implementing realistic smoke injection heights, and applying high-resolution models that better resolve vertical transport.

54 ENVIRONMENTAL SCIENCES↗

Functional group activation and coupling agent migration induced by plasma treatment in adhesive for enhanced toughness of metal-composite joints

Commercial adhesive paste was additionally activated using low-power oxygen plasma with different plasma exposure durations to investigate its interfacial bonding contribution in adhesively-bonded Aural-5/CFRP-PA6 double cantilever beam (DCB) joints with plasma-treated adherends. The plasma-treated adhesive showed enhanced functional peak intensities in Fourier transfer infrared spectroscopy (FTIR) as plasma exposure time was increased, and some degree of oxidation was also detected via X-ray photoelectron spectroscopy (XPS). A small molecule, dicyandiamde (coupling agent) in adhesive was migrated to adhesive layer, where double concentration of coupling agent was detected after 10 minutes of plasma treatment. As a result, characterization of the adhesive/CFRP-PA6 interface after DCB fracture showed additional chemical bonds formed through amine-initiated epoxy ring opening polymerization, as well as amide bonds and ester bonds. In conclusion, these additional bonds at the adhesive/CFRP-PA6 interfaces led to significantly increased failure extensions and fracture energies of the joints as the plasma exposure time on the adhesive increased, compared to the joints with plasma-treated adherends but non-plasma-treated adhesive as commonly seen in the literature.

36 MATERIALS SCIENCE↗

Phenotypic transition maps of 3D breast acini obtained by imaging-guided agent-based modeling

We introduce an agent-based model of epithelial cell morphogenesis to explore the complex interplay between apoptosis, proliferation, and polarization. By varying the activity levels of these mechanisms we derived phenotypic transition maps of normal and aberrant morphogenesis. These maps identify homeostatic ranges and morphologic stability conditions. The agent-based model was parameterized and validated using novel high-content image analysis of mammary acini morphogenesis in vitro with focus on time-dependent cell densities, proliferation and death rates, as well as acini morphologies. Model simulations reveal apoptosis being necessary and sufficient for initiating lumen formation, but cell polarization being the pivotal mechanism for maintaining physiological epithelium morphology and acini sphericity. Furthermore, simulations highlight that acinus growth arrest in normal acini can be achieved by controlling the fraction of proliferating cells. Interestingly, our simulations reveal a synergism between polarization and apoptosis in enhancing growth arrest. After validating the model with experimental data from a normal human breast line (MCF10A), the system was challenged to predict the growth of MCF10A where AKT-1 was overexpressed, leading to reduced apoptosis. As previously reported, this led to non growth-arrested acini, with very large sizes and partially filled lumen. However, surprisingly, image analysis revealed a much lower nuclear density than observed for normal acini. The growth kinetics indicates that these acini grew faster than the cells comprising it. The in silico model could not replicate this behavior, contradicting the classic paradigm that ductal carcinoma in situ is only the result of high proliferation and low apoptosis. Our simulations suggest that overexpression of AKT-1 must also perturb cell-cell and cell-ECM communication, reminding us that extracellular context can dictate cellular behavior.

59 BASIC BIOLOGICAL SCIENCES↗

Source of Processable Vitrimer Viscosities: Swap Frequencies and Steric Factors

Vitrimers exhibit high, processable viscosities, where other polymers do not, and are among the most promising polymers for closed-loop material circularity. We sought to investigate the underlying chemical kinetic factors that result in high viscosities for vitrimers, which are crucial to designing vitrimers with tunable viscosity. To interrogate these factors, we achieved the first simulated predictions of real vitrimer viscosities, using a novel kinetic Monte Carlo molecular dynamics method, overcoming the time and length scale gaps to predict experimental bulk viscosities. The vitrimer architecture investigated is based on poly(dimethylsiloxane) chains and vinylogous urethane bond swaps. We probed the effects of the extent of free swapping groups, %F, the activation energy, E A , and the steric factor, ρ. The steric factor is related to the intrinsic reaction probability for molecules with sufficient energy. All three factors were found to be significant, but the role of ρ was found to be the biggest and also the most underappreciated. The results show that the inclusion of accurate ρ is of critical importance for viscosity predictions, with the evidence suggesting that the typical assumption of ρ = 1 is not valid for vitrimers and that, indeed, very low steric factors are present in bond-swap vitrimers such that values of ρ < 10 –10 may be typical. This greatly influences the bond exchange rates and, ultimately, the viscosities. Recognition of this result is necessary for the prediction of vitrimer viscosities from molecular simulations and to make vitrimers by design from molecular dynamics. We also investigated the effects that E A , ρ, and the number of free swapping groups have upon vitreous range temperatures, TV, with respect to achieving a specific viscosity (η V = 1 × 10 8 Pa·s), as well as for a commonly reported higher viscosity extrapolation (η V = 1 × 10 12 Pa·s). The evidence suggests that vitrimers may follow universal curves for E A vs T V , as a function of ρ. Finally, this study achieves the first of these comparisons of molecular simulations to experiments and reveals critical insights toward creating vitrimers by design, while providing a route for the prediction of T V from kinetic Monte Carlo molecular dynamics simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Unrivaled combination of surface area and pore volume in micelle-templated carbon for supercapacitor energy storage

Here, we created Immense Surface Area Carbons (ISACs) by a novel heat treatment that stabilized the micelle structure in a biological based precursor prior to high temperature combined activation – pyrolysis. While displaying a morphology akin to that of commercial activated carbon, ISACs contain an unparalleled combination of electrochemically active surface area and pore volume (up to 4051 m 2 g –1 , total pore volume 2.60 cm 3 g –1 , 76% small mesopores). The carbons also possess the benefit of being quite pure (combined O and N: 2.6–4.1 at%), thus allowing for a capacitive response that is primarily EDLC. Tested at commercial mass loadings (~10 mg cm –2 ) ISACs demonstrate exceptional specific capacitance values throughout the entire relevant current density regime, with superior rate capability primarily due to the large fraction of mesopores. In the optimized ISAC, the specific capacitance ( C g ) is 540 F g –1 at 0.2 A g –1 , 409 F g –1 at 1 A g –1 and 226 F g –1 at a very high current density of 300 A g –1 (~0.15 second charge time). At intermediate and high currents, such capacitance values have not been previously reported for any carbon. Tested with a stable 1.8 V window in a 1 M Li 2 SO 4 electrolyte, a symmetric supercapacitor cell yields a flat energy–power profile that is fully competitive with those of organic electrolyte systems: 29 W h kg –1 at 442 W kg –1 and 17 W h kg –1 at 3940 W kg –1 . The cyclability of symmetric ISAC cells is also exceptional due to the minimization of faradaic reactions on the carbon surface, with 80% capacitance retention over 100 000 cycles in 1 M Li 2 SO 4 and 75 000 cycles in 6 M KOH.

25 ENERGY STORAGE↗

Molecular Genetic Analysis of Activation-tagged Transcription Factors Thought to be Involved in Photomorphogenesis

Plants utilize light as a source of information via families of photoreceptors such as the red/far-red absorbing phytochromes (PHY) and the blue/UVA absorbing cryptochromes (CRY). The main goal of the Neff lab is to use molecular-genetic mutant screens to elucidate signaling components downstream of these photoreceptors. Activation-tagging mutagenesis led to the identification of two putative transcription factors that may be involved in both photomorphogenesis and hormone signaling pathways. sob1-D (suppressor of phyB-dominant) mutant phenotypes are caused by the over-expression of a Dof transcription factor previously named OBP3. Our previous studies indicate that OBP3 is a negative regulator of light-mediated cotyledon expansion and may be involved in modulating responsiveness to the growth-regulating hormone auxin. The sob2-D mutant uncovers a role for LEP, a putative AP2/EREBP-like transcription factor, in seed germination, hypocotyl elongation and responsiveness to the hormone abscisic acid. Based on photobiological and genetic analysis of OBP3-knockdown and LEP-null mutations, we hypothesize that these transcription factors are involved in both light-mediated seedling development and hormone signaling. To examine the role that these genes play in photomorphogenesis we will: 1) Further explore the genetic role of OBP3 in cotyledon/leaf expansion and other photomorphogenic processes as well as examine potential physical interactions between OBP3 and CRY1 or other signaling components that genetically interact with this transcription factor 2) Test the hypothesis that OBP3 is genetically involved in auxin signaling and root development as well as examine the affects of this hormone and light on OBP3 protein accumulation. 3) Test the hypothesis that LEP is involved in seed germination, seedling photomorphogenesis and hormone signaling. Together these experiments will lead to a greater understanding of the complexity of interactions between photoreceptors and DNA-interacting proteins during photomorphogenesis. These studies also address the roles OBP3 and LEP may play as points of intersection between hormone signaling and photomorphogenesis. In the future, phenotypes caused by altered expression of these genes may generate useful traits for improving crop yield.

59 BASIC BIOLOGICAL SCIENCES↗

Novel Composite Materials for SOFC Cathode-Interconnect Contact

This report summarized the research efforts and major conclusions of our University Coal Research Project, which focused on developing a new class of electrically-conductive, Cr-blocking, damage-tolerant Ag-perovksite composite materials for the cathode-interconnect contact of intermediate-temperature solid oxide fuel cell (SOFC) stacks. The Ag evaporation rate increased linearly with air flow rate initially and became constant for the air flow rate {ge} {approx} 1.0 cm {center_dot} s{sup -1}. An activation energy of 280 KJ.mol{sup -1} was obtained for Ag evaporation in both air and Ar+5%H{sub 2}+3%H{sub 2}O. The exposure environment had no measurable influence on the Ag evaporation rate as well as its dependence on the gas flow rate, while different surface morphological features were developed after thermal exposure in the oxidizing and reducing environments. Pure Ag is too volatile at the SOFC operating temperature and its evaporation rate needs to be reduced to facilitate its application as the cathode-interconnect contact. Based on extensive evaporation testing, it was found that none of the alloying additions reduced the evaporation rate of Ag over the long-term exposure, except the noble metals Au, Pt, and Pd; however, these noble elements are too expensive to justify their practical use in contact materials. Furthermore, the addition of La{sub 0.8}Sr{sub 0.2}MnO{sub 3} (LSM) into Ag to form a composite material also did not significantly modify the Ag evaporation rate. The Ag-perovskite composites with the perovskite being either (La{sub 0.6}Sr{sub 0.4})(Co{sub 0.8}Fe{sub 0.2})O{sub 3} (LSCF) or LSM were systematically evaluated as the contact material between the ferritic interconnect alloy Crofer 22 APU and the LSM cathode. The area specific resistances (ASRs) of the test specimens were shown to be highly dependent on the volume percentage and the type of the perovskite present in the composite contact material as well as the amount of thermal cycling that the specimens were subjected to during testing. The Ag-LSCF composite contact materials proved more effective in trapping Cr within the contact material and preventing Cr migration into the cathode than the Ag-LSM composites. Ag-perovskite composite contact materials are promising candidates for use in intermediate-temperature SOFC stacks with ferritic stainless steel interconnects due to their ability to maintain acceptably low ASRs while reducing Cr migration into the cathode material.

01 COAL, LIGNITE, AND PEAT↗

Energy efficient indoor VOC air cleaning with activated carbon fiber (ACF) filters

This study explores the potential environmental and energy benefits of using activated carbon fiber (ACF) filters for air cleaning in HVAC systems. The parallel aims for the air cleaning system were to enable reduced indoor exposures to volatile organic compounds (VOCs) and to simultaneously allow reduced rates and energy consumption for outdoor-air ventilation. We evaluated the use of ACF media to adsorb VOCs from indoor air during repeated simulated 12-hour to 24-hour periods of occupancy. In a cyclic regeneration process, VOCs were desorbed from the ACF media and vented outdoors to enable the next cycle of air cleaning. The VOC removal efficiency of the ACF media was measured using a 9.5-cm 2 ACF specimen exposed to a mixture of VOCs that included toluene, benzene, o-xylene, 1-butanol, limonene, undecane and formaldehyde at 29 °C and 30 percent relative humidity. The concentrations of these model pollutants upstream of the ACF media were in the range 20 to 30 ppb, to simulate realistic conditions. Velocities through the ACF media were typical of those in normal particle filter systems (~ 0.5 m s -1 ). Initial tests were conducted to develop a modified multi-component Freundlich isotherm and estimate the maximum adsorption capacity of the media, which was determined to be 90 mg VOC per gram of ACF. Three different ACF regeneration methods were explored using relatively cleaner outdoor air under ambient conditions, with this air humidified, and with the filter heated. It was found that heating the ACF media to ~150 °C by circulation of a DC current through the fibers for a short period (15 minutes) yielded the best VOC removal results, allowing for subsequent consistent removal efficiencies of 70-80 percent for most VOCs. Regeneration with unheated outdoor air was also effective and used less energy (subsequent removal efficiency was 50-60 percent for most VOCs). ACF did not perform as well in eliminating formaldehyde, for which a maximum removal of 25-30 percent was achieved with heated regeneration. A mass balance model indicated that the combination of ACF air cleaning and a 50percent reduction in ventilation will decrease indoor concentrations of VOCs by 60 percent to 80 percent and reduce formaldehyde concentrations by 12 percent to 40 percent. Energy modeling indicated the potential to reduce the energy required for heating and cooling of ventilation air by 35 percent to almost 50 percent.

54 ENVIRONMENTAL SCIENCES↗

Handbook: Collecting Groundwater Samples from Monitoring Wells in Frenchman Flat, CAU 98

Frenchman Flat basin on the Nevada National Security Site (NNSS) contains Corrective Action Unit (CAU) 98, which is comprised of ten underground nuclear test locations. Environmental management of these test locations is part of the Underground Test Area (UGTA) Activity conducted by the U.S. Department of Energy (DOE) under the Federal Facility Agreement and Consent Order (FFACO) (1996, as amended) with the U.S. Department of Defense (DOD) and the State of Nevada. A Corrective Action Decision Document (CADD)/Corrective Action Plan (CAP) has been approved for CAU 98 (DOE, 2011). The CADD/CAP reports on the Corrective Action Investigation that was conducted for the CAU, which included characterization and modeling. It also presents the recommended corrective actions to address the objective of protecting human health and the environment. The recommended corrective action alternative is “Closure in Place with Modeling, Monitoring, and Institutional Controls.” The role of monitoring is to verify that Contaminants of Concern (COCs) have not exceeded the Safe Drinking Water Act (SDWA) limits (Code of Federal Regulations, 2014) at the regulatory boundary, to ensure that institutional controls are adequate, and to monitor for changed conditions that could affect the closure conditions. The long-term closure monitoring program will be planned and implemented as part of the Closure Report stage after activities specified in the CADD/CAP are complete. Groundwater at the NNSS has been monitored for decades through a variety of programs. Current activities were recently consolidated in an NNSS Integrated Sampling Plan (DOE, 2014). Although monitoring directed by the plan is not intended to meet the FFACO long-term monitoring requirements for a CAU (which will be defined in the Closure Report), the objective to ensure public health protection is similar. It is expected that data collected in accordance with the plan will support the transition to long-term monitoring at each CAU. The sampling plan is designed to ensure that monitoring activities occur in compliance with the UGTA Quality Assurance Plan (DOE, 2012). The sampling plan should be referenced for Quality Assurance (QA) elements and procedures governing sampling activities. The NNSS Integrated Sampling Plan specifies the groundwater monitoring that will occur in CAU 98 until the long-term monitoring program is approved in the Closure Report. The plan specifies the wells that must be monitored and categorizes them by their sampling objective with the associated analytical requirements and frequency. Possible sample collection methods and required standard operating procedures are also presented. The intent of this handbook is to augment the NNSS Integrated Sampling Plan by providing well-specific details for the sampling professional implementing the Sampling Plan in CAU 98, Frenchman Flat. This handbook includes each CAU 98 well designated for sampling in the NNSS Integrated Sampling Plan. The following information is provided in the individual well sections: 1. The purpose of sampling. 2. A physical description of the well. 3. The chemical characteristics of the formation water. 4. Recommended protocols for purging and sampling. The well-specific information has been gathered from numerous historical and current sources cited in each section, but two particularly valuable resources merit special mention. These are the USGS NNSS website (http://nevada.usgs.gov/doe_nv/ntsarea5.cfm) and the UGTA Field Operations website (https://ugta.nv.doe.gov/sites/Field%20Operations/default.aspx). 2 Land surface elevation and measuring point for water level measurements in Frenchman Flat were a focus during CAU investigations (see Appendix B, Attachment 1 in Navarro-Intera, 2014). Both websites listed above provide information on the accepted datum for each well. A summary is found on the home page for the well on the USGS website. Additional information is available through a link in the “Available Data” section to an “MP diagram” with a photo annotated with the datum information. On the UGTA Field Operations well page, the same information is in the “Wellhead Diagram” link. Well RNM-2s does not have an annotated photo at this time. All of the CAU 98 monitoring wells are located within Area 5 of Frenchman Flat, with the exception of ER-11-2 in Area 11 (Figure 1). The wells are clustered in two areas: the northern area (Figure 2) and the central area (Figure 3). Each well is discussed below in geographic order from north to south as follows: ER-11-2, ER-5-3 shallow piezometer, ER-5-3-2, ER-5-5, RNM-1, RNM-2s, and UE-5n.

(1996↗

Life Sciences Accomplishments 1994

The NASA Life and Biomedical Sciences and Applications Division (LBSAD) serves the Nation's life sciences community by managing all aspects of U.S. space-related life sciences research and technology development. The activities of the Division are integral components of the Nation's overall biological sciences and biomedical research efforts. However, NASA's life sciences activities are unique, in that space flight affords the opportunity to study and characterize basic biological mechanisms in ways not possible on Earth. By utilizing access to space as a research tool, NASA advances fundamental knowledge of the way in which weightlessness, radiation, and other aspects of the space-flight environment interact with biological processes. This knowledge is applied to procedures and technologies that enable humans to live and work in and explore space and contributes to the health and well-being of people on Earth. The activities of the Division are guided by the following three goals: Goal 1) Use microgravity and other unique aspects of the space environment to enhance our understanding of fundamental biological processes. Goal 2) Develop the scientific and technological foundations for supporting exploration by enabling productive human presence in space for extended periods. Goal 3) Apply our unique mission personnel, facilities, and technology to improve education, the quality of life on Earth, and U.S. competitiveness. The Division pursues these goals with integrated ground and flight programs involving the participation of NASA field centers, industry, and universities, as well as interactions with other national agencies and NASA's international partners. The published work of Division-sponsored researchers is a record of completed research in pursuit of these goals. During 1993, the LBSAD instituted significant changes in its experiment solicitation and peer review processes. For the first time, a NASA Research Announcement (NRA) was released requesting proposals for ground-based and flight research for all programs. Areas of particular interest to NASA were defined Proposals due April 29, 1994, will be peer reviewed - externally for scientific merit. This annual NRA process is now the mechanism for recruiting both extramural and intramural investigations. As an overview of LBSAD activities in 1993, this accomplishments document covers each of the major organizational components of the Division and the accomplishments of each. The second section is a review of the Space Life Sciences Research programs Space Biology, Space Physiology and Countermeasures, Radiation Health, Environmental Health, Space Human Factors, Advanced Life Support, and Global Monitoring and Disease Prediction, The third section, Research in Space Flight, describes the substantial contributions of the Spacelab Life Sciences 2 (SLS-2) mission to life sciences research and the significant contributions of the other missions flown in 1993, along with plans for future missions. The Division has greatly expanded and given high priority to its Education and Outreach Programs, which are presented in the fourth section. The fifth and final section, Partners for Space, shows the Divisions Cooperative efforts with other national and international agencies to achieve common goals, along with the accomplishments of joint research and analysis programs.

Burnell, Mary Lou↗

Tc-99 Adsorption on Selected Activated Carbons - Batch Testing Results

CH2M HILL Plateau Remediation Company (CHPRC) is currently developing a 200-West Area groundwater pump-and-treat system as the remedial action selected under the Comprehensive Environmental Response, Compensation, and Liability Act Record of Decision for Operable Unit (OU) 200-ZP-1. This report documents the results of treatability tests Pacific Northwest National Laboratory researchers conducted to quantify the ability of selected activated carbon products (or carbons) to adsorb technetium-99 (Tc-99) from 200-West Area groundwater. The Tc-99 adsorption performance of seven activated carbons (J177601 Calgon Fitrasorb 400, J177606 Siemens AC1230AWC, J177609 Carbon Resources CR-1240-AW, J177611 General Carbon GC20X50, J177612 Norit GAC830, J177613 Norit GAC830, and J177617 Nucon LW1230) were evaluated using water from well 299-W19-36. Four of the best performing carbons (J177606 Siemens AC1230AWC, J177609 Carbon Resources CR-1240-AW, J177611 General Carbon GC20X50, and J177613 Norit GAC830) were selected for batch isotherm testing. The batch isotherm tests on four of the selected carbons indicated that under lower nitrate concentration conditions (382 mg/L), Kd values ranged from 6,000 to 20,000 mL/g. In comparison. Under higher nitrate (750 mg/L) conditions, there was a measureable decrease in Tc-99 adsorption with Kd values ranging from 3,000 to 7,000 mL/g. The adsorption data fit both the Langmuir and the Freundlich equations. Supplemental tests were conducted using the two carbons that demonstrated the highest adsorption capacity to resolve the issue of the best fit isotherm. These tests indicated that Langmuir isotherms provided the best fit for Tc-99 adsorption under low nitrate concentration conditions. At the design basis concentration of Tc 0.865 µg/L(14,700 pCi/L), the predicted Kd values from using Langmuir isotherm constants were 5,980 mL/g and 6,870 mL/g for for the two carbons. These Kd values did not meet the target Kd value of 9,000 mL/g. Tests conducted to ascertain the effects of changing pH showed that at pH values of 6.5 and 7.5, no significant differences existed in Tc-adsorption performance for three of the carbons, but the fourth carbon performed better at pH 7.5. When the pH was increased to 8.5, a slight decline in performance was observed for all carbons. Tests conducted to ascertain the temperature effect on Tc-99 adsorption indicated that at 21 ºC, 27 ºC, and 32 ºC there were no significant differences in Tc-99 adsorption for three of the carbons. The fourth carbon showed a noticeable decline in Tc-99 adsorption performance with increasing temperature. The presence of volatile organic compounds (VOCs) in the source water did not significantly affect Tc-99 adsorption on either of two carbons tested. Technetium-99 adsorption differed by less than 15% with or without VOCs present in the test water, indicating that Tc-99 adsorption would not be significantly affected if VOCs were removed from the water prior to contact with carbon.

54 ENVIRONMENTAL SCIENCES↗

Templated Growth and Passivation of Vertically Oriented Antimony Selenide Thin Films for High-Efficiency Solar Cells in Substrate Configuration

Antimony selenide (Sb 2 Se 3 ) is a promising low-cost photovoltaic material with a 1D crystal structure. The grain orientation and defect passivation play a critical role in determining the performance of polycrystalline Sb 2 Se 3 thin-film solar cells. In this work, a seed layer is introduced on a molybdenum (Mo) substrate to template the growth of a vertically oriented, columnar Sb 2 Se 3 absorber layer by closed space sublimation. By controlling the grain orientation and compactness of the Sb 2 Se 3 seeds, obtain high-quality Sb 2 Se 3 absorber layers with passive Sb 2 Se 3 /Mo interfaces is obtained, which in turn improve the transport of photoexcited charge carriers through the absorber layer and its interfaces. Post-deposition annealing of absorber layers in ambient air is further utilized to passivate the defects in Sb 2 Se 3 and enhance the quality of the front heterojunction. As a result of systematic processing optimization, Sb 2 Se 3 planar heterojunction solar cells are fabricated in substrate configuration with a champion power conversion efficiency of 8.5%.

14 SOLAR ENERGY↗