Size-controlled nanocrystals reveal spatial dependence and severity of nanoparticle coalescence and Ostwald ripening in sintering phenomena
Colloidal nanocrystals allow investigating sintering phenomena in supported catalysts.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Colloidal nanocrystals allow investigating sintering phenomena in supported catalysts.
Low temperature sintering enables dense composites of ceramic active materials and conductive agents. Conductivity and microstructure of composites is characterized.
Ligand-passivated ErOCl nanocrystals have been synthesized using a non-hydrolytic sol–gel method. Anisotropic sintering of ErOCl nanocrystals enhances 2D chloride-ion diffusion along theabplane, yielding a promising candidate for halide batteries.
The coercivity of surface grains of a Nd-Fe-B sintered magnet can be measured unequivocally if the magnet is a thin slab with the orientation of its c-axis parallel to the largest surface. Due to the loss of part of the neodymium-rich grain boundary phase, the surface Nd{sub 2}Fe{sub 14}B grains have low coercivity after machining. When a Nd layer is sputter deposited on the surface and annealed in the temperature range from 500 to 675 deg. C, the surface coercivity recovers to its full value, which is identical to the coercivity of the bulk magnet from which the slab was cut. Transmission electron microscopy has indicated the formation of a fcc interfacial phase having a lattice constant a=0.548 nm between the surface grains and the Nd layer in the specimen whose surface coercivity was recovered. In addition to a double hexagonal closed packed phase (metallic Nd), A-type Nd{sub 2}O{sub 3} has been observed in the inner region of the Nd film away from the interface. A-type Nd{sub 2}O{sub 3} having a hexagonal structure with a=0.382 nm and c=0.598 nm is the most stable phase of the neodymium oxides with 2:3 stoichiometry. Since the fcc phase is derived from metastable C-type Nd{sub 2}O{sub 3} having a cubic structure with a=1.108 nm, the fcc phase is also a metastable phase. Therefore it is considered that the formation of the fcc phase results from the interfacial energy with the Nd{sub 2}Fe{sub 14}B grains.
Spark plasma sintering is a powerful method to produce fine grain dense ferrite at low temperature. However the process, usually conducted in neutral atmosphere in a carbon die, yields carbon surface deposition and the reduction of Fe{sup 3+} into Fe{sup 2+}. It is shown that subsequent annealing in air can remove carbon and under some conditions produce complete oxidation of Fe{sup 2+} ions. Regular values of the resistivity and permittivity (resp., 1 M{Omega}m, 13 {epsilon}{sub 0}) are recovered for most samples annealed at temperatures not higher than 750 deg. C. A relatively high value of the permeability (up to 240) and a high merit factor ({mu}{sub s}xf{sub r}>5 GHz) have been achieved.
Multiferroic BiFeO{sub 3} (BFO)/La{sub 0.7}Sr{sub 0.3}MnO{sub 3} heterostructured thin films were grown by pulsed laser deposition on polished spark plasma sintered LaAlO{sub 3} (LAO) polycrystalline substrates. Both polycrystalline LAO substrates and BFO films were locally characterized using electron backscattering diffraction, which confirmed the high-quality local epitaxial growth on each substrate grain. Piezoforce microscopy was used to image and switch the piezo-domains, and the results are consistent with the relative orientation of the ferroelectric variants with the surface normal. This high-throughput synthesis process opens the routes towards wide survey of electronic properties as a function of crystalline orientation in complex oxide thin film synthesis.
In this study, microstructure and magnetic properties of sintered Nd-Fe-B magnets with addition of Dy{sub 82.3}Co{sub 17.7} (wt. %) were investigated. By adding a small amount of Dy{sub 82.3}Co{sub 17.7}, the coercivity is improved greatly, and the irreversible loss is decreased sharply. The increase of Curie temperature suggests that Co atoms have entered into the 2:14:1 main phase. Microstructural analysis indicates that a well-developed core-shell structure was formed in the magnets with the addition of Dy{sub 82.3}Co{sub 17.7}. The improvement of magnetic properties can be attributed to the microstructural modification and the intrinsic properties' improvement.
The R-Fe-B (R, rare earth) sintered magnets prepared with different ratio of alloys of MM-Fe-B (MM, misch-metal) and Nd-Fe-B by dual alloy method were investigated. As expected, the high ratio of MM-Fe-B alloy degrades the hard magnetic properties heavily with intrinsic coercivity lower than 5 kOe. When the atomic ratio MM/R ≤ 21.5% the magnetic properties can reach a practical level of B{sub r} ≥ 12.1 kGs, H{sub cj} ≥ 10.7 kOe, and (BH){sub max} ≥ 34.0 MGOe. And the effect of H{sub cj} enhancement by the grain boundary diffusion process is obvious when MM/R ≤ 21.5%. It is revealed that the decrement of intrinsic magnetic properties of R{sub 2}Fe{sub 14}B matrix phase is not the main reason of the degradation of the magnets with high MM ratio. The change of deteriorated microstructure together with phase component plays fundamental roles in low H{sub cj}. In high MM ratio magnets, (a) after annealing, Ce atoms inside main phase are inclined to be segregated in the outer layer of the main phase grains; (b) there is no thin layer of Ce-rich phase as an analogue of Nd-rich phase to separate main phase grains; (c) excessive Ce tends to form CeFe{sub 2} grains.
The magnetism in the grain-boundary phase of a NdFeB sintered magnet was measured by spin-polarized scanning electron microscopy (spin SEM). A sample magnet was fractured in the ultra-high-vacuum chamber to avoid oxidation, and its magnetizations in the exposed grain-boundary phase on the fracture surface were evaluated through the spin polarization of secondary electrons. Spin-SEM images were taken as the fracture surface was milled gradually by argon ions, and the magnetization in the grain-boundary phase was quantitatively obtained separately from that of the Nd{sub 2}Fe{sub 14}B phase. The obtained magnetization shows that the grain-boundary phase of this magnet has substantial magnetization, which was confirmed to be ferromagnetic.
This clathrate had a maximum dimensionless figure-of-merit, ZT, of 0.93 at 637 K, which was slightly higher than that of 0.83 for the sintered type-VIII clathrate Ba{sub 8}Ga{sub 16}Sn{sub 30}. We investigated the high-temperature thermoelectric properties, transport properties, electronic structures, and thermal stabilities of the clathrates. The type-II clathrate was found to be superior to the type-VIII clathrate as a thermoelectric material; it had a high thermal stability and melting point, 859 K, high mobility, 141 cm{sup 2}V{sup −1}s{sup −1} at 300 K, because of its low inertial mass, and low high-temperature lattice thermal conductivity, approximately 4 mW cm{sup −1}K{sup −1}, resulting from a larger unit cell and weaker bipolar thermal conduction. We discuss these properties in terms of the electronic structure and the differences between the two types of clathrate.
We used magnetic domain observation to statistically observe the thermal demagnetization behavior of Nd–Fe–B sintered magnets at elevated temperatures up to 150 °C. Simultaneous magnetization reversal in a hundred adjacent grains occurred at 90 °C because of the magnetic interaction among the grains beyond grain boundaries in the Dysprosium (Dy)-free low-coercivity magnet. Conversely, simultaneous magnetization reversal in a hundred grains did not occur in the Dy-added high-coercivity magnets, and the demagnetizing ratio steadily increased with temperature. Furthermore, the addition of Dy induced high thermal stability by eliminating the simultaneous thermal demagnetization, which was caused by the magnetic interaction among the grains.
We developed a fabrication process of an epitaxial MgAl{sub 2}O{sub 4} barrier for magnetic tunnel junctions (MTJs) using a direct sputtering method from an MgAl{sub 2}O{sub 4} spinel sintered target. Annealing the sputter-deposited MgAl{sub 2}O{sub 4} layer sandwiched between Fe electrodes led to the formation of a (001)-oriented cation-disorder spinel with atomically sharp interfaces and lattice-matching with the Fe electrodes. A large tunnel magnetoresistance ratio up to 245% at 297 K (436% at 3 K) was achieved in the Fe/MgAl{sub 2}O{sub 4}/Fe(001) MTJ as well as an excellent bias voltage dependence. These results indicate that the direct sputtering is an alternative method for the realization of high performance MTJs with a spinel-based tunnel barrier.
The growth, sintering, and interaction of cobalt with ceria were studied under ultrahigh vacuum conditions by vapor-deposition of Co onto well-defined CeOx(111) (1.5 < x < 2) thin films grown on Ru(0001). Charge transfer from Co to ceria occurs upon deposition of Co on CeO 1.96 and partially reduced CeO 1.83 at 300 K. X-ray photoelectron spectroscopy studies show that Co is oxidized to Co 2+ species at the cost of the reduction of Ce 4+ to Ce 3+ , at a lesser extent on reduced ceria. Co 2+ is the predominant species on CeO 1.96 at low Co coverages (e.g., ≤0.20 ML). The ratio of metallic Co/Co 2+ increases with the increase in the Co coverage. However, both metallic Co and Co 2+ species are present on CeO 1.83 even at low Co coverages with metallic Co as the major species. Scanning tunneling microscopy results demonstrate that Co tends to wet the CeO 1.96 surface at very low Co coverages at room temperature forming one-atomic layer high structures of Co–O–Ce. The increase in the Co coverage can cause the particle growth into three-dimensional structures. The formation of slightly flatter Co particles was observed on reduced CeO 1.83 . In comparison with other transition metals including Ni, Rh, Pt, and Au, our studies demonstrate that Co on ceria exhibits a smaller particle size and higher thermal stability, likely arising from strong metal–support interactions. The formed particles upon Co deposition at 300 K are present on the ceria surface after heating to 1000 K. The Co–ceria interface can be tuned by varying the Co metal coverage, the annealing temperature, and the nature of the ceria surface.
We investigated phase relations in pyrolite at -33--40 GPa and -1800--2150 K by in situ X-ray diffraction using Kawai-type apparatus with sintered diamond anvils. The results demonstrated that MgSiO{sub 3}-rich orthorhombic perovskite (mpv), CaSiO{sub 3}-rich cubic perovskite (cpv) and (Mg,Fe)O ferropericlase (fp) are the stable phases in pyrolite bulk composition at the conditions corresponding to the lower mantle. However, chemical analyses of a run product recovered from -34 GPa by an analytical transmission electron microscope showed the coexistence of metallic iron particles with mpv, fp, and SiO{sub 2}-rich amorphous phase. Also, Fe/Mg partitioning coefficient between mpv and fp was found to be 0.66(31), which is consistent with previous results for pyrolite bulk composition at 26--30 GPa and -1900 K. These results indicate that iron-rich metallic particles can exist in the lower mantle as a stable phase to the depth of at least -900 km.
A sample of Al with grain size of 5.1 mu m, prepared by spark plasma sintering, was deformed to a nominal strain of 0.35% under exposure to X-ray synchrotron radiation, allowing spatially resolved orientation measurements to be made during loading by use of a micro-diffraction technique. A significant heterogeneity in the deformation pattern between grains was observed. A statistical analysis shows that grain deformation depends more on crystallographic orientation than on grain size, with grains with tensile axis lying towards the < 001>-< 101> border of the unit triangle tending to undergo larger deformation. Other possible reasons for the different deformation behaviour between individual grains are briefly discussed.
Here, in this study, we present a study of the influence of microstructure on the magnetic properties of polycrystalline samples of the La 1.5 Sr 0.5 CoMnO 6 double perovskite, with primary attention to the spontaneous exchange bias effect, a fascinating recently discovered phenomena for which some materials exhibit unidirectional magnetic anisotropy after being cooled in zero magnetic fields. By sintering La 1.5 Sr 0.5 CoMnO 6 at different temperatures, we obtained samples with distinct average grain sizes, ranging from 1.54-6.65 μm. A detailed investigation of the material's structural, morphologic, electronic, and magnetic properties using x-ray powder diffraction, powder neutron diffraction, x-ray absorption near edge structure spectroscopy, scanning electron microscopy, and ac and dc magnetometry has revealed a systematic enhancement of the exchange bias effect with increasing the average grain size. This evolution is discussed in terms of changes in the material's porosity and grain morphology and its influence on the exchange couplings at the magnetic interfaces.
An experimental investigation on electric contact resistance in the tooling utilized in spark plasma sintering (SPS) is conducted. Two different SPS regimes are operated without the presence of processed powder to obtain the punch–punch (horizontal) and punch–die (vertical) contact resistance assessments separately. The processing temperature and applied pressure are considered to be the main factors that affect the contact resistance. These effects are analyzed by performing experiments at a maximum temperature of 1600°C with constant heating rate of 100°C/min. The applied pressure is ranging from 20 to 60 MPa and a 1 min holding time‐step is used to ensure stable measurements. It is shown that the contact resistance goes down as the temperature ramps up. An increase in the pressure leads to a decrease in the contact resistance. The mechanisms that cause these variations in the contact resistance are discussed. The dependence of assessed contact resistance of the utilized SPS system on the processing temperature and applied pressure is analytically described based on the regression analysis of the collected experimental data. A finite‐element simulation based on the obtained experimental results evidences that the electric contact resistance dominates the temperature evolution. The obtained results are of significant importance for modeling and optimization of SPS processes.
Abstract We report results from in‐situ measurements of lattice expansion during flash sintering of 3 mol% yttria stabilized tetragonal zirconia taken at the Advanced Photon Source, Argonne National Laboratory. The expansion is anisotropic, with the relative expansion of the a ‐lattice constant exceeding that of the c ‐lattice constant. The anisotropic expansion cannot be explained by thermal expansion and is consistent with predictions from ab‐initio calculations based upon the generation of vacancy‐interstitial pairs of zirconium and oxygen.