Search NASA⌕ Search

SEARCH · Search NASA

Results for “WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Microstructure and mechanical properties of resistance-spot-welded joints for A5052 aluminum alloy and DP 600 steel

The microstructure and mechanical properties of resistance-spot-welded A5052 aluminum alloy and DP 600 dual-phase steel joint were studied. The fusion zone (FZ) and heat-affected zone (HAZ) of DP 600 exhibited lath martensite and ferrite-martensite structures, respectively. The microstructure of FZ and HAZ in the A5052 side was composed of cellular crystals and the boundary region of FZ exhibited a columnar crystal morphology. A Fe{sub 2}Al{sub 5} intermetallic compound (IMC) layer with 3.3 μm thickness was found adjacent to the DP 600 side, whereas a needle-shaped Fe{sub 4}Al{sub 13} IMC layer with length of 0.67 μm to 15.8 μm was found adjacent to the aluminum alloy side. The maximum tensile shear load of the A5052/DP 600 joint was 5.5 KN, with a corresponding molten nugget diameter of 6.3 mm. The fracture morphology of the optimized A5052/DP 600 joint was mainly an elongated dimple fracture accompanied by cleavage fracture. - Highlights: •A5052 and DP 600 with large gaps in properties were investigated by RSW. •The microstructures of RSW joints in DP 600/A5052 were examined detailedly. •The micro/macro-characteristics and strength relations of joints were analyzed.

36 MATERIALS SCIENCE↗

The relationship between low-temperature toughness and secondary crack in low-carbon bainitic weld metals

Highlights: • The crack propagation plane was identified with the decreasing possibility of {110}/{100}, {112} and {123}. • Crack path deviates at some middle-angle misorientation boundaries with high strain concentration. • The most effective barrier to arrest crack in Ni0 and Ni2 is the boundaries of inter-Bain in a CPP packet, while in Ni4 the boundaries of inter-CPP and intra-Bain packets impede crack propagation. - Abstract: This paper aims to reveal the relationship among low-temperature toughness, microstructure and secondary crack from both microstructural and crystallographic perspectives. Instrumented Charpy tests were carried out in the upper platform, transition temperature range, as well as at lower temperatures. Quantitative fractographic analysis, microstructural characterization and secondary crack observation were conducted on half of the impact specimen. Crystallographic features were identified in the secondary crack proximity, e.g. variant selection, orientation relationship, cleavage plane of the corresponding crack matrix. Some results in literature are confirmed. Nickel addition is beneficial to hindering crack propagation as a result of microstructure improvement. The most effective barrier for crack propagation is high-angle misorientation boundaries between Bain packets and the boundaries of ferrite matrix with the microstructure of granular bainite. Additionally, high-angle misorientation boundaries between closed-packed plane packets arrest cracks in the mixed microstructure of fine lath bainite and intricate acicular ferrite. Most preferred crack propagation planes are {110} and {100} in our low carbon bainitic weld metals, with the decreasing possibility of {112} and {123}.

36 MATERIALS SCIENCE↗

THE CHOICE OF OPTIMAL STRUCTURE OF ARTIFICIAL NEURAL NETWORK CLASSIFIER INTENDED FOR CLASSIFICATION OF WELDING FLAWS

Nondestructive testing and evaluation are under continuous development. Currently researches are concentrated on three main topics: advancement of existing methods, introduction of novel methods and development of artificial intelligent systems for automatic defect recognition (ADR). Automatic defect classification algorithm comprises of two main tasks: creating a defect database and preparing a defect classifier. Here, the database was built using defect features that describe all geometrical and texture properties of the defect. Almost twenty carefully selected features calculated for flaws extracted from real radiograms were used. The radiograms were obtained from shipbuilding industry and they were verified by qualified operator. Two weld defect's classifiers based on artificial neural networks were proposed and compared. First model consisted of one neural network model, where each output neuron corresponded to different defect group. The second model contained five neural networks. Each neural network had one neuron on output and was responsible for detection of defects from one group. In order to evaluate the effectiveness of the neural networks classifiers, the mean square errors were calculated for test radiograms and compared.

42 ENGINEERING↗

Set up an Arc Welding Code with Enthalpy Method in Upwind Scheme

In this study, a numerical code with enthalpy method in upwind scheme is proposed to estimate the distribution of thermal stress in the molten pool, which is primarily determined by the type of the input power and travel speed of heating source. To predict the cracker deficit inside the workpiece, a simulated program satisfying the diagonal domination and Scarborough criterion provides a stable iteration. Meantime, an experimental performance, operated by robot arm 'DR-400' to provide a steady and continuous arc welding, was also conducted to verify the simulated result. By surveying the consistence of molten pool bounded by contrast shade and simulated melting contour on the surface of workpiece, the validity of model proposed to predict the thermal cracker has been successfully identified.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Diode laser welding of aluminum to steel

Laser welding of dissimilar materials was carried out by using a high power diode laser to join aluminum to steel in a butt-joint configuration. During testing, the laser scan rate was changed as well as the laser power: at low values of fluence (i.e. the ratio between laser power and scan rate), poor joining was observed; instead at high values of fluence, an excess in the material melting affected the joint integrity. Between these limiting values, a good aesthetics was obtained; further investigations were carried out by means of tensile tests and SEM analyses. Unfortunately, a brittle behavior was observed for all the joints and a maximum rupture stress about 40 MPa was measured. Apart from the formation of intermeltallic phases, poor mechanical performances also depended on the chosen joining configuration, particularly because of the thickness reduction of the seam in comparison with the base material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structure and properties of fixed joints formed by ultrasonic-assisted friction-stir welding

This paper deals with structure and properties of aluminum alloy 7475 and its joints obtained by friction stir welding including under ultrasonic action. Microhardness measurements show that ultrasonic action increases strength properties of the joints. Optical and transmission electron microscopy reveals that this effect is related to the precipitation of tertiary coherent S-and T-phase particles.

36 MATERIALS SCIENCE↗

Impact of tool wear on joint strength in friction stir spot welding of DP 980 steel

Friction stir spot welding has been shown to be a viable method of joining ultra high strength steel (UHSS), both in terms of joint strength and process cycle time. However, the cost of tooling must be reasonable in order for this method to be adopted as an industrial process. Recently a new tool alloy has been developed, using a blend of PCBN and tungsten rhenium (W-Re) in order to improve the toughness of the tool. Wear testing results are presented for two of these alloys: one with a composition of 60% PCBN and 40% W-Re, and one with 70% PCBN and 30% W-Re. The sheet material used for all wear testing was 1.4 mm DP 980. Lap shear testing was used to show the relationship between tool wear and joint strength. The Q70 tool provided the best combination of wear resistance and joint strength.

36 MATERIALS SCIENCE↗

Pressure Resistance Welding of High Temperature Metallic Materials

Pressure Resistance Welding (PRW) is a solid state joining process used for various high temperature metallic materials (Oxide dispersion strengthened alloys of MA957, MA754; martensitic alloy HT-9, tungsten etc.) for advanced nuclear reactor applications. A new PRW machine has been installed at the Center for Advanced Energy Studies (CAES) in Idaho Falls for conducting joining research for nuclear applications. The key emphasis has been on understanding processing-microstructure-property relationships. Initial studies have shown that sound joints can be made between dissimilar materials such as MA957 alloy cladding tubes and HT-9 end plugs, and MA754 and HT-9 coupons. Limited burst testing of MA957/HT-9 joints carried out at various pressures up to 400oC has shown encouraging results in that the joint regions do not develop any cracking. Similar joint strength observations have also been made by performing simple bend tests. Detailed microstructural studies using SEM/EBSD tools and fatigue crack growth studies of MA754/HT-9 joints are ongoing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hybrid Ultrasonic TOFD Imaging of Weld Flaws Using Wavelet Transforms and Image Registration

Ultrasonic time of flight diffraction (TOFD) is an effective weld crack inspection technique. Due to the intensity of diffraction wave is rather weak compared with the lateral wave and the bottom echo wave, thus the signal-to-ratio (SNR) of TOFD image is low. A new dichotomous method is comprised of two steps that contains wavelet shrinkage and image registration is proposed in this paper to reduce the noise and improve the resolution of TOFD images as well. In order to evaluate the reliability of our proposed method in this paper, we have established the experiment system, and sampled a number of TOFD data with random distribution of noise characteristics. We adopted one-dimension wavelet transform and two-dimension wavelet transform in the very beginning of the first step of the proposed algorithm respectively. The SNR of the result obtained in this step is improved significantly compared with the classic algorithms. Next, the image registration is applied. After the registered images have been added to form a new one, then it comes to the final result that shows not only the SNR but also the definition of the image is enhanced effectively.

42 ENGINEERING↗

Dissolution of Nb(C,N) and (Ti,V)N in the Coarse-Grained Heat-Affected Zone of Electric Resistance Welded X65 Line Pipe

Nb-rich and Ti/V-rich precipitates were introduced into the X65 linepipe via thermomechanical controlled processing. Their dissolution kinetics were investigated in the coarse-grained heat-affected zone after electric resistance welding. Nb-rich precipitates were found to dissolve completely, whereas Ti/V-rich precipitates were found to dissolve partially, because of slower dissolution kinetics. In conclusion, a complete dissolution of Nb-rich precipitates was associated with significant austenite grain coarsening, which promoted bainite as a quench product, which might have reduced the impact toughness.

microstructure↗

Friction Stir Welding of Al-B{sub 4}C Composite Fabricated by Accumulative Roll Bonding: Evaluation of Microstructure and Mechanical Behavior

In this investigation, friction stir welding (FSW) of Al-B{sub 4}C composite fabricated by 10 cycles accumulative roll bonding was conducted. In order to investigate the influences of pin geometry on microstructure and mechanical properties, four different pin geometries (cylindrical, square, triangular and hexagonal) were selected. It was found that FSW parameters had a major effect on the fragmentation and distribution of reinforcement particles in stir zone. When the tool travel speed was increased, the distribution of B{sub 4}C particles was become gradually uniform in the aluminum matrix. The effect of tool rotational speed on the peak temperature was determined to be greater than the tool travel speed. The attained data of tensile properties and microhardness tests showed that the tool travel speed had bilateral effect on the tensile strength. The maximum tensile joint efficiency was obtained as 238% for FSWed of Al-2%B{sub 4}C composite to annealed base Al sheet.

36 MATERIALS SCIENCE↗

Process Parameter Optimization in Refill Friction Spot Welding of 6061 Aluminum Alloys Using Response Surface Methodology

6061-T6 aluminum alloy joint was fabricated by refill friction stir spot welding (RFSSW) on which three process parameters of tool rotation speed, sleeve moving rate, and plunge depth make an important effect. The response surface methodology (RSM) was applied to establish a mathematical model to study the effect of process parameters on lap shear fracture load (LSFL) of the RFSSWed joints which were performed in Box–Behnken designs with three factors, three levels and 15 runs. Analysis of variance used to check the adequacy of the developed model indicates that the mathematical model is significant. LSFL increases with the increase in tool rotation speed, sleeve plunge depth, and sleeve moving rate to maximum and then decreases. Sleeve plunge depth makes the most effect on LSFL in all process parameters. The RFSSW process parameters were also optimized using RSM to predict maximize LSFL. The joint produced using a tool rotational speed of 1506 rpm, sleeve moving rate of 1.01 mm/s and sleeve plunge depth of 2.46 mm displays higher LSFL.

36 MATERIALS SCIENCE↗

Microstructure and Wear Resistance of FeCrBSi Plasma-Sprayed Coating Remelted by Gas Tungsten Arc Welding Process

Herein, an FeCrBSi coating was fabricated via plasma spray on AISI1045 steel, and subsequently, a gas tungsten arc welding (GTA) process was employed to remelt the coating. The microstructure, microhardness, fracture toughness and surface roughness of the coating before and after remelting were investigated, as well as the wear resistance was tested by a UMT-3-type sliding wear apparatus. The results showed that, upon remelting, most defects in the as-sprayed coating were effectively eliminated, the surface roughness decreased by 43%, and the coating–substrate interface bonding changed from mechanical to metallurgical. The phase composition of the as-sprayed coating was primarily α-Fe and a small amount of hard Fe{sub 3}B phase, while the remelted coating consisted of α-Fe and (Fe,Cr){sub 23}C{sub 6} and a small quantity of CrB. In addition, remelting the coating was found to induce a 287.6% increase in the fracture toughness, a 33.4% increase in the average microhardness, and a 47.5% decrease in the wear volume, while the failure mechanism changed from abrasive wear to fatigue wear upon remelting. Therefore, GTA remelting of plasma-sprayed coating was found to be a feasible method to obtain a coating with good wear resistance.

36 MATERIALS SCIENCE↗

Residual Stresses in Explosively Welded Plates Made of Titanium Grade 12 and Steel with Interlayer

Distributions of residual stress components in explosively welded three-layer plate composed of titanium Grade 12, titanium Grade 1 and SA516 Grade 70 steel are investigated in this paper. The study applied the sectioning and the hole-drilling strain gage methods for residual stress measurement. The results have shown an inhomogeneous residual stress distribution, approximated by fourth-order polynomial along the thickness of a three-layer plate. Biaxial compressive residual stress state is observed in titanium Grade 12 and Grade 1 layers which change to tensile type in the vicinity of the interface between titanium Grade 1 and steel. Microstructure observation reveals the presence of the adiabatic shear bands in titanium Grade 12 layer at the interface with titanium Grade 1 interlayer. The observed distribution of residual stress components is justified by the occurrence of the shock wave phenomena.

36 MATERIALS SCIENCE↗

High Wear-Resistant Aluminum Matrix Composite Layer Fabricated by MIG Welding with Lateral B{sub 4}C Powder Injection

In this work, a low-cost technique combining MIG welding and lateral powder injection was developed to fabricate B{sub 4}C particles-reinforced aluminum matrix composite (AMC) layer on a T6 heat-treated 7075 aluminum alloy (AA7075-T6) substrate. The AMC layer was 6-7 mm thick and well bonded to the substrate. The B{sub 4}C particles were dispersed throughout the AMC layer with an average content of approximately 7 vol.%. No significant reaction products existed either at the particle–matrix interface or in the Al-matrix. In pin-on-disk dry sliding wear tests against Al{sub 2}O{sub 3} grinding wheels, the AMC layer exhibited excellent wear resistance with volume wear rate approximately 1/10-3/10 that of the quenched AISI 1045 steel and only approximately 2-7% that of the AA7075-T6 alloy under the same wear conditions. A small addition of ceramic particles can greatly improve wear resistance, suggesting that this technique has good prospects for a wide variety of applications.

36 MATERIALS SCIENCE↗

Variation in Morphology and Kinetics of Granular Bainite with Welding Thermal Cycles in High-Nb Fire-Resistant Steel: Experiments and Theoretical Calculations

The microstructure and kinetics of granular bainite (GB) were investigated in novel fire-resistant steel containing high niobium and subjected to simulated welding thermal cycles. The dilatometric data were analyzed to determine the activation energy and Avrami exponents. It was observed that austenite transformed to GB over a wide range cooling rates of 0.5-100 K/s. Theoretical calculations indicated that Avrami exponent (n) decreased with increased transformed volume fraction (f{sub b}) and cooling rate. At a moderate cooling rate of 20-6 K/s, bainitic ferrite as sheaves formed from austenite and the corresponding Avrami exponent was 2 < n < 3. Martensite in martensite/austenite constituent formed with Avrami exponent n ~ 1. At the fastest cooling rate of 50 K/s, lath bainitic ferrite and film-like retained austenite (RA) were obtained with the corresponding Avrami exponent n ~ 1. At lower cooling of 1 and 0.5 K/s, plate-like bainitic ferrite and block-like microphase composed of lamellar RA and ferrite were obtained with Avrami exponent n > 3. The local activation energy for austenite transformation to bainitic ferrite decreased from ~ 198 to ~ 182 kJ/mol with increasing f{sub b} from 0.05 to 0.95, while the local activation energy for austenite transformation to martensite decreased from ~ 80 to ~ 71 kJ/mol with increasing f{sub b} from 0.05 to 0.95.

36 MATERIALS SCIENCE↗

Effect of Preheating and Water Cooling on the Performance of Friction-Stir-Welded Aviation-Grade Aluminum Alloy Joints

This paper examined the effect of preheating and water cooling on the thermal, mechanical, metallurgical, and texture properties of friction-stir-welded AA6082. Joints are fabricated under different preheating (FSW-P) and water cooling (FSW-C) conditions. The experimental outcomes indicate that the preheating and water cooling enhance the mechanical properties of the joint. The maximum tensile strength of 295 MPa is obtained for FSW-P1. It is also observed that preheating has more impact on microhardness. Microstructural analysis using optical microscope and electron backscatter diffraction analysis indicated that FSW produced fine equiaxed grains in the nugget zone due to dynamic recrystallization. Texture analysis shows that finer grain grains are obtained under preheating and water cooling conditions. The minimum grain size of 5.3 µm is obtained under FSW-P1. X-ray diffraction analysis shows that Mg{sub 2}Si phase in nugget zone that is an indication of dissolution and formation of strengthening precipitates. Fracture analysis indicates that preheating also improves the ductility of the joint.

36 MATERIALS SCIENCE↗

A Comparative Study of Deformation Behaviors Between Laser-Welded Joints and Base Metal of Ti-22Al-24.5Nb-0.5Mo Alloy

The tensile deformation behaviors of laser-welded Ti-22Al-24.5Nb-0.5Mo alloy joints have been investigated at room temperature and 650 °C using in situ tensile analysis methods. The α{sub 2} phase had a significant influence on deformation behaviors of base metal at room temperature and 650 °C. The microcracks mainly nucleated in B2/α{sub 2} phase boundaries or within α{sub 2} phase and then propagated along B2/α{sub 2} phase boundaries subsequently. Compared with the plastic fracture of base metal, the fracture modes of the fully B2-phase fusion zone at room temperature and 650 °C were quasi-cleavage and intergranular fracture, respectively. While dislocation slips became foremost deformation mode in the fusion zone at room temperature, there were a great amount of slip bands on the surface of grains caused by the slip systems. The microcracks of fusion zone at 650 °C nucleated and propagated along the grain boundaries of B2 phase. Owing to the lack of grain deformation, the cross-slip bands were in small quantities on the surface of B2 phase grains.

36 MATERIALS SCIENCE↗