Search NASA⌕ Search

SEARCH · Search NASA

Results for “active solids”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Effect of Nickel Microstructure on Methane Steam-Reforming Activity of Ni-YSZ Cermet Anode Catalyst

The activity of nickel-yttria stabilized zirconia (Ni-YSZ) solid oxide fuel cell (SOFC) cermet anodes for the steam reforming of methane has been investigated in the absence of electrochemical effects. The cermet was prepared by co-milling and sintering NiO and 5YSZ powders at 1375oC in air. During the high temperature sintering step, NiO dissolved into the YSZ particles to form a solid NiO-YSZ solution. During the subsequent catalyst reduction step, Ni exolved from the YSZ. As a result, many small Ni particles on the order of 10-20 nm formed at the surface of the YSZ. These small particles contribute significantly to the overall reforming activity, along with the large bulk Ni particles within the Ni-YSZ cermet. We have observed high initial activity that decreases by as much as an order of magnitude with time on stream, until the anode catalyst reaches a stable steady state activity. The time to reach this stable activity is a function of the reaction conditions and feed gas composition. Higher temperature, hydrogen partial pressure, and space velocity all accelerated the deactivation rate at a constant steam-to-carbon ratio of 3. Initial and lined out activities and average turnover frequencies were obtained for both Ni-YSZ and bulk Ni, based on a rate expression that is first order in methane and zero order in steam. Comparative tests at 750oC show high initial activity on a per-Ni site basis with both materials, but these turnover rates decline over a period of a few hours. Following lineout, there appears to be a negligible effect of Ni particle size on turnover rate. These results indicate the presence of structure sensitivity for methane reforming, but only with freshly calcined and reduced catalysts that may contain highly coordinatively unsaturated sites. There is an apparent structure insensitivity with aged catalysts where Ni particle sizes are generally 50 nm and greater. Under reaction conditions that employ high space velocities and low methane conversions, the water-gas-shift reaction does not establish thermodynamic equilibrium.

03 NATURAL GAS↗

Self-Assembly Driven Microlithography via Near-Infrared Light Activation

Current vat photopolymerization (VP) relies on UV or visible light to start the rapid crosslinking of liquid photocurable resins into 3D-printed structures. Here, we develop a self-assembly-driven photopatterning approach to photothermally generate polymeric solids by combining thermoplasmonic nanoparticles and thermoresponsive polymers, in which near-infrared (NIR) light activates thermoplasmonic heating of nanoparticles, triggering the irreversible self-assembly of thermoresponsive polymers into insoluble mesoglobules. A small amount of thermal initiator and crosslinker leads to irreversible self-assembly of polymer nanocomposites. NIR light offers deeper penetration and reduced scattering compared to UV, enabling more uniform curing of thicker or filled materials and expanded process control for composites or opaque systems. Thermoplasmonic heat generation is achieved using surface-modified gold nanorods (AuNRs) with a longitudinal localized surface plasmon resonance peak in the NIR region. Key variables such as polymer composition, molecular weight, physical interactions at the nanoparticle–polymer interface, which can be tuned by surface functionalization, AuNR concentration, and pH can be used to tailor the assembly behavior of these systems, including photothermal effect, flocculation, and cloud point temperature, and the mechanical properties of the final structures. Collectively, these results highlight a platform for photothermally-driven microlithography of polymer solids with diverse, tunable macroscopic properties, enabled by low-energy NIR light-activated self-assembly.

36 MATERIALS SCIENCE↗

Method for producing nanoparticles and the nanoparticles produced therefrom

Disclosed herein is a method comprising disposing a container containing a metal and/or ferromagnetic solid and abrasive particles in a static magnetic field; where the container is surrounded by an induction coil; activating the induction coil with an electrical current, to heat up the metallic or ferromagnetic solid to form a fluid; generating sonic energy to produce acoustic cavitation and abrasion between the abrasive particles and the container; and producing nanoparticles that comprise elements from the container, the metal and/or the ferromagnetic solid and the abrasive particles. Disclosed herein too is a composition comprising first metal or a first ceramic; and particles comprising carbides and/or nitrides dispersed therein. Disclosed herein too is a composition comprising nanoparticles comprising chromium carbide, iron carbide, nickel carbide, y.-Fe and magnesium nitride.

36 MATERIALS SCIENCE↗

Method for producing nanoparticles and the nanoparticles produced therefrom

Disclosed herein is a method comprising disposing a container containing a metal and/or ferromagnetic solid and abrasive particles in a static magnetic field; where the container is surrounded by an induction coil; activating the induction coil with an electrical current, to heat up the metallic or ferromagnetic solid to form a fluid; generating sonic energy to produce acoustic cavitation and abrasion between the abrasive particles and the container; and producing nanoparticles that comprise elements from the container, the metal and/or the ferromagnetic solid and the abrasive particles. Disclosed herein too is a composition comprising first metal or a first ceramic; and particles comprising carbides and/or nitrides dispersed therein. Disclosed herein too is a composition comprising nanoparticles comprising chromium carbide, iron carbide, nickel carbide, γ-Fe and magnesium nickel.

36 MATERIALS SCIENCE↗

Method for producing nanoparticles and the nanoparticles produced therefrom

Disclosed herein is a method comprising disposing a container containing a metal and/or ferromagnetic solid and abrasive particles in a static magnetic field; where the container is surrounded by an induction coil; activating the induction coil with an electrical current, to heat up the metallic or ferromagnetic solid to form a fluid; generating sonic energy to produce acoustic cavitation and abrasion between the abrasive particles and the container; and producing nanoparticles that comprise elements from the container, the metal and/or the ferromagnetic solid and the abrasive particles. Disclosed herein too is a composition comprising first metal or a first ceramic; and particles comprising carbides and/or nitrides dispersed therein. Disclosed herein too is a composition comprising nanoparticles comprising chromium carbide, iron carbide, nickel carbide, γ-Fe and magnesium nitride.

Manuel, Michele Viola↗

Method for producing nanoparticles and the nanoparticles produced therefrom

Disclosed herein is a method comprising disposing a container containing a metal and/or ferromagnetic solid and abrasive particles in a static magnetic field; where the container is surrounded by an induction coil; activating the induction coil with an electrical current, to heat up the metallic or ferromagnetic solid to form a fluid; generating sonic energy to produce acoustic cavitation and abrasion between the abrasive particles and the container; and producing nanoparticles that comprise elements from the container, the metal and/or the ferromagnetic solid and the abrasive particles. Disclosed herein too is a composition comprising first metal or a first ceramic; and particles comprising carbides and/or nitrides dispersed therein. Disclosed herein too is a composition comprising nanoparticles comprising chromium carbide, iron carbide, nickel carbide, γ-Fe and magnesium nitride.

Manuel, Michele Viola↗

Method for producing nanoparticles and the nanoparticles produced therefrom

Disclosed herein is a method comprising disposing a container containing a metal and/or ferromagnetic solid and abrasive particles in a static magnetic field; where the container is surrounded by an induction coil; activating the induction coil with an electrical current, to heat up the metallic or ferromagnetic solid to form a fluid; generating sonic energy to produce acoustic cavitation and abrasion between the abrasive particles and the container; and producing nanoparticles that comprise elements from the container, the metal and/or the ferromagnetic solid and the abrasive particles. Disclosed herein too is a composition comprising first metal or a first ceramic; and particles comprising carbides and/or nitrides dispersed therein. Disclosed herein too is a composition comprising nanoparticles comprising chromium carbide, iron carbide, nickel carbide, γ-Fe and magnesium nitride.

Manuel, Michele Viola↗

Parts per Million Powder X-ray Diffraction

Here in this paper we demonstrate the use of second harmonic generation (SHG) microscopy-guided synchrotron powder X-ray diffraction (PXRD) for the detection of trace crystalline active pharmaceutical ingredients in a common polymer blend. The combined instrument is capable of detecting 100 ppm crystalline ritonavir in an amorphous hydroxypropyl methylcellulose matrix with a high signal-to-noise ratio (>5000). The high spatial resolution afforded by SHG microscopy allows for the use of a minibeam collimator to reduce the total volume of material probed by synchrotron PXRD. The reduction in probed volume results in reduced background from amorphous material. The ability to detect low crystalline loading has the potential to improve measurements in the formulation pipeline for pharmaceutical solid dispersions, for which even trace quantities of crystalline active ingredients can negatively impact the stability and bioavailability of the final drug product.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Decay Dose Shielding Analysis with Hybrid Unstructured Mesh/Constructive Solid Geometry Monte Carlo Calculation and ADVANTG Acceleration

The Oak Ridge National Laboratory (ORNL) Second Target Station (STS) neutron production facility is an accelerator driven pulsed neutron source that is currently being actively developed at ORNL. The neutrons are produced by proton-induced spallation reactions. A proton beam of 700 kW power is delivered to a spallation target in short, less than 1 µs long pulses, with 15 Hz repetition rate. The spallation target of ORNL STS is a rotating water-cooled tungsten target with tantalum cladding housed in a stainless-steel shroud. It is divided into 21 segments. These segments become highly activated due to spallation reactions or nuclei transmutation by the emitted neutrons. The radioactive nuclides continue to decay after ceasing operation. The decay dose rates generated from the target segments once they are removed from their operational location within the core vessel must be accurately quantified to determine the shielding configurations of remote handling tools and transport casks and to aid in planning maintenance events. To determine the shielding configurations needed for an activated target segment after ceasing operation, both the hybrid unstructured mesh (UM)/constructive solid geometry (CSG) approach that was previously utilized for STS analyses [1] and the ADVANTG code [2] were used. Even though the ADVANTG code does not include UM capability, the utilization of its advanced variance reduction technique was crucial to accelerate the extremely difficult final photon transport calculation in this analysis. This paper also describes the procedures taken to mitigate the convergence issues that occur when ADVANTG uses a source definition that does not match the source of the final Monte Carlo (MC) calculation. These convergence issues often occur because of inconsistencies between source and transport biasing parameters.

Ibrahim, Ahmad↗

Probing Electrochemical Mg-Ion Activity in MgCr 2– x V x O 4 Spinel Oxides

Mg migration in oxide spinels is impeded by strong affinity between divalent Mg and oxygen, suggesting a necessity of exploring new chemistry of solid lattices for functional Mg-ion electrode materials. Cationic mobility with a suitable activation energy in Cr spinels is Tn. evidenced by theoretical and experimental results, while redox potentials of V are appropriate to operate with currently limited candidates of '''c" nonaqueous electrolytes. By controlling the structure, composition, and complexity, a largely solid-solution MgCrVO 4 spinel was synthesized, which, unlike nanocornposites, can bring together the advantages of each transition metal in the lattice. The spinel was successfully synthesized by a simple solid-state reaction with minor inactive Cr- or V-rich components, which was confirmed via 25 Mg MAS NMR and high-resolution X-ray diffraction analyses. A thermally and anodically stable Mg(TPFA) 2 /triglyme electrolyte was utilized for high-temperature electrochemistry and lowering kinetic barriers at and across interfaces so as to observe intercalation behavior of Mg in the designed lattice. Multimodal characterization confirmed an apparent bulk demagnesiation from MgCrVO 4 with partial reversibility by probing evolution of the local and long-range structure as well as vanadium and chromium electronic states within the lattice. Furthermore, characterization experiments also provided a direct evidence for (de)intercalation reactions that occurred without any major competitive conversion reactions or insertion of protons into the lattice, except for the formation of a surface rock salt phase upon charge. These findings in Mg-ion activity expand opportunities to design Mg spinel oxide materials while highlighting the need to identify the origins of reversibility challenges due to, but not limited to, phase stability, particularly for the charged states, barriers at the interface, electrolyte stabilities, and desolvation phenomena, collectively hindering practical use as cathode materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Distribution of P{sub 2}O{sub 5} and Na{sub 2}O Between Solid Solution and Liquid Phase in the CaO-SiO{sub 2}-Fe{sub 2}O{sub 3}-P{sub 2}O{sub 5}-Na{sub 2}O Slag System with High P{sub 2}O{sub 5} Content

The phosphorus content in hot metal will increase in future, because iron ores are steadily deteriorating in quality. Na{sub 2}O addition to slag is considered an effective method for increasing the efficiency of dephosphorization. In addition, Na{sub 2}O modification also facilitates phosphorus recovery from dephosphorization slag with high P{sub 2}O{sub 5} content by selective leaching. Therefore, it is necessary to investigate the distribution ratios of P{sub 2}O{sub 5} and Na{sub 2}O between solid solution and liquid phase in the CaO-SiO{sub 2}-Fe{sub 2}O{sub 3}-P{sub 2}O{sub 5}-Na{sub 2}O slag system. A linear relationship was found between the distribution ratio of P{sub 2}O{sub 5} and the Na{sub 2}O content in slag, and was independent of P{sub 2}O{sub 5} content. When the Na{sub 2}O content was high, the Na{sub 2}O content in the solid solution approached saturation and a new 2CaO·SiO{sub 2}-2CaO·Na{sub 2}O·P{sub 2}O{sub 5} solid solution formed. The addition of Na{sub 2}O decreased the P{sub 2}O{sub 5} content in solid solution, while it increased the mass fraction of solid solution in slag. The distribution ratio of P{sub 2}O{sub 5} increased with increase in the Fe{sub 2}O{sub 3} content and basicity of slag. An increase in P{sub 2}O{sub 5} content in slag results in an increase in the activity coefficient of P{sub 2}O{sub 5} both in the liquid phase and in the solid solution.

36 MATERIALS SCIENCE↗

Activated carbon supported Ni, Fe, and bimetallic NiFe catalysts for CO x -free H 2 production by microwave methane pyrolysis

The goal of this study was to test the effect of metal-impregnated carbon-based catalysts on the conversion of methane to hydrogen gas and solid carbon using microwave reactor technology. Monometallic and bimetallic catalysts on activated carbon supports (Ni/AC, Fe/AC, Ni-Fe/AC) are compared during methane pyrolysis testing. Catalytic methane pyrolysis was carried out in a microwave reactor at reaction temperatures of 600 °C and 800 °C. For comparison, one of the catalysts (Ni-Fe/AC) was tested in a conventionally heated reactor at 800 °C. The prepared catalysts were characterized by X-ray diffraction (XRD), while post-reaction catalysts were characterized by XRD and SEM. During reaction testing, the monometallic Ni/AC catalyst exhibited the best catalytic activity (CH 4 conversion: 46.0 and H 2 yield: 46.9%) when reacted in the microwave reactor, however, it suffered from rapid deactivation from carbon deposition (carbon yield: 0.39 gC/g catalyst). The bimetallic Ni-Fe/AC catalyst was slightly less active (CH 4 conversion: 36.9 and H 2 yield: 40.5%) but it was more resistant to carbon formation (carbon yield: 0.27 gC/g catalyst) suggesting it may have greater long-term stability. The Ni-Fe/AC catalyst was also the most energy efficient as it required the least microwave power to maintain the 800 °C reaction temperature compared to the other catalysts tested. Methane conversion of the bimetallic Ni-Fe/AC at 800 °C under microwave irradiation was three times the conversion under conventional heating at the same reaction temperature. Finally, this work demonstrates the use of microwave-specific catalysts for catalytic methane pyrolysis in a microwave reactor, and can be used as a foundation for further methane pyrolysis process and catalyst optimization for CO x -free H 2 production.

08 HYDROGEN↗

Jointly Sponsored Research Program Energy Related Research

Cooperative Agreement, DE-FC26-98FT40323, Jointly Sponsored Research (JSR) Program at Western Research Institute (WRI) began in 1998. Over the course of the Program, a total of seventy-seven tasks were proposed utilizing a total of $23,202,579 in USDOE funds. Against this funding, cosponsors committed $26,557,649 in private funds to produce a program valued at $49,760,228. The goal of the Jointly Sponsored Research Program was to develop or assist in the development of innovative technology solutions that will: (1) Increase the production of United States energy resources - coal, natural gas, oil, and renewable energy resources; (2) Enhance the competitiveness of United States energy technologies in international markets and assist in technology transfer; (3) Reduce the nation's dependence on foreign energy supplies and strengthen both the United States and regional economies; and (4) Minimize environmental impacts of energy production and utilization. Under the JSR Program, energy-related tasks emphasized enhanced oil recovery, heavy oil upgrading and characterization, coal beneficiation and upgrading, coal combustion systems development including oxy-combustion, emissions monitoring and abatement, coal gasification technologies including gas clean-up and conditioning, hydrogen and liquid fuels production, coal-bed methane recovery, and the development of technologies for the utilization of renewable energy resources. Environmental-related activities emphasized cleaning contaminated soils and waters, processing of oily wastes, mitigating acid mine drainage, and demonstrating uses for solid waste from clean coal technologies, and other advanced coal-based systems. Technology enhancement activities included resource characterization studies, development of improved methods, monitors and sensors. In general the goals of the tasks proposed were to enhance competitiveness of U.S. technology, increase production of domestic resources, and reduce environmental impacts associated with energy production and utilization. This report summarizes the accomplishments of the JSR Program.

01 COAL, LIGNITE, AND PEAT↗

Soil Interim Measures Implementation Report Q6 Radar Station – Solid Waste Management Unit 112 Locations of Concern 3 and 10 Kennedy Space Center, Florida

This report presents a summary of the soil interim measures (IM) implementation activities that occurred from January 23 through June 6, 2023, at the Q6 Radar Station (Q6RS) Solid Waste Management Unit (SWMU) 112, located at the John F. Kennedy Space Center (KSC), Florida. The site is monitored under KSC’s Resource Conservation and Recovery Act Corrective Action Program, which also meets the requirements of Chapter 62-780, Florida Administrative Code. Assessment activities have previously been performed at 10 Q6RS Locations of Concern (LOCs), identified during a SWMU assessment in 2013 (NASA 2013). Since the SWMU assessment, further confirmatory sampling and assessment was conducted for each LOC, and based on the data collected during these assessments, it was determined that Resource Conservation and Recovery Act Facility Investigation to further evaluate soil and groundwater was to be conducted at two LOCs: LOC 1 – Former Underground Storage Tanks (groundwater) and LOC 3 – Radar Antenna Refurbishment Area (soil). The LOC 1 groundwater assessment is ongoing, and the results will be presented under a separate cover. It was also determined that soil IM would be completed at two of the LOCs, LOC 3 and LOC 10 – Compressor Building Condensate Discharge. A Soil IM Work Plan was prepared and submitted in October 2021 (NASA 2021). The plan proposed excavation and disposal of barium and copper impacted soil in the LOC 3 and 10 areas. This report presents a summary and results of the soil IM implementation activities conducted at LOCs 3 and 10. The site contaminates of concern for this soil IM are barium and copper. The activities presented in this report includes soil IM implementation and groundwater sampling. From January 23 through March 24, 2023, AECOM Technical Services, Inc. (AECOM) field personnel conducted IM implementation activities in the LOC 3 and 10 areas. As presented in the IM Work Plan, shallow soils, impacted with metals, were excavated to a depth of 2 feet below land surface in the central area of the site around the radar antenna and associated equipment. AECOM personnel excavated 77.43 tons of soil using hand tools and, when able, heavy equipment. The soils were placed into lined roll-off containers, which were covered and transported under manifest to the Cedar Trail Landfill in Bartow, Florida. The site was restored to original condition using certified clean backfill material (sand), with filter fabric, and gravel. Areas outside of the excavation were restored with grass seed. On June 6, 2023, AECOM field personnel conducted groundwater sampling activities within the soil IM excavation area. AECOM personnel collected one groundwater sample from monitoring well Q6RS-MW0003. The sample was submitted to a fixed-based laboratory for analysis by United States Environmental Protection Agency Method 6020B for metals (barium and copper). Barium and copper were detected at 18 micrograms per liter (µg/L) and 14 µg/L, respectively, and were below the State of Florida Groundwater Cleanup Target Levels (GCTLs) for barium at 2,000 µg/L and copper at 1,000 µg/L.

Chadwick Sloan Lee↗

Application of time-of-flight secondary ion mass spectrometry to the detection of surface intermediates during the first cycle of atomic layer deposition (ALD) of platinum on silica surfaces

Atomic layer deposition (ALD) has become the method of choice for many applications requiring the controlled growth of thin films on solid surfaces. Yet, the use of metalorganic precursors typical in these depositions adds significant complexity to the chemistry involved. Unfortunately, it is difficult to obtain direct information about the surface species that participate in the reaction mechanisms of ALD. Here we illustrate the value of using time-of-flight secondary ion mass spectrometry (ToF-SIMS) for this purpose. A specific example is provided, a study of the first cycle of deposition of platinum using trimethyl(methylcyclopentadienyl)platinum (IV), or MeCpPt(CH 3 ) 3, on silicon oxide surfaces. In previous investigations of this process, we have determined that the low reactivity of the MeCpPt(CH 3 ) 3 precursor, which hinders fast deposition, can be partially overcome by gas-phase electron-impact activation. What has not been clear is what chemical species form on the solid surface as a result of such activation. Here we show that the MeCp ligand is quite stable and that it remains intact and coordinated to the Pt atoms upon adsorption on the surface. It was also established that some of the methyl groups may remain bound to the Pt center: the main species detected on the silicon oxide surfaces were MeCpPt and MeCpPt(CH 3 ). On the other hand, it appears that no Pt intermediates without MeCp ligands are formed during this initial adsorption. Finally, O 2 treatment of these surfaces at elevated temperature to complete the first ALD cycle leads to the complete removal of all the organic ligands: no evidence for MeCp or methyl groups is seen in the ToF-SIMS traces from the final samples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mobile Interfaces: Liquids as a Perfect Structural Material for Multifunctional, Antifouling Surfaces

Life creates some of its most robust, extreme surface materials not from solids but from liquids: a purely liquid interface, stabilized by underlying nanotexture, makes carnivorous plant leaves ultraslippery, the eye optically perfect and dirt-resistant, our knees lubricated and pressure-tolerant, and insect feet reversibly adhesive and shape-adaptive. Novel liquid surfaces based on this idea have recently been shown to display unprecedented omniphobic, self-healing, anti-ice, antifouling, optical, and adaptive properties. In this Perspective, we present a framework and a path forward for developing and designing such liquid surfaces into sophisticated, versatile multifunctional materials. Drawing on concepts from solid materials design and fluid dynamics, we outline how the continuous dynamics, responsiveness, and multiscale patternability of a liquid surface layer can be harnessed to create a wide range of unique, active interfacial functions able to operate in harsh, changing environments not achievable with static solids. We discuss how, in partnership with the underlying substrate, the liquid surface can be programmed to adaptively and reversibly reconfigure from a defect-free, molecularly smooth, transparent interface through a range of finely tuned liquid topographies in response to environmental stimuli. With nearly unlimited design possibilities and unmatched interfacial properties, liquid materials as long-term stable interfaces yet in their fully liquid state may potentially transform surface design everywhere from medicine to architecture to energy infrastructure.

Grinthal, A↗

Testing the Activation Analysis for Fusion in OpenMC

OpenMC is a community-developed Monte Carlo neutron and photon transport simulation code. It can perform fission simulations such as fixed-source, k-eigenvalue, and subcritical multiplication calculations on models built using either a constructive solid geometry or CAD representation. To explore the use of OpenMC for fusion activation analysis, a detailed model of the Fusion Neutronics Science Facility (FNSF) was first developed for comparisons against an existing SERPENT model. A 90-degree model of FNSF in Standard-Triangle-Language (STL) CAD format was converted to Constructive Solid Geometry (CSG) using each code's built-in functions, and the geometries were validated by ensuring no cells overlapped and no particles were lost during simulations. The neutron fluxes were calculated and compared for multiple components close to the plasma. The results show differences mostly below 1% in fluxes and averaged 8% for activity and decay heat. Here, the work described in this study tests the CAD-based geometry using the DagMC toolkit in OpenMC and compares the activation analysis of OpenMC to SERPENT code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recent Progress in Solid‐State Lithium Batteries through Cathode Microstructure Engineering

A high‐performance cathode is necessary to realize the great potentials of solid‐state batteries such as high energy density and long cycle life. It is also needed to validate electrolyte performance, which is lacking. Currently, cathodes for solid‐state batteries are thinner and have lower cathode active material content than their lithium‐ion battery counterpart, resulting from insufficient conductivity and limiting the battery energy density. This review article provides an overview of recent development in cathode microstructures and their impact on battery properties, including compatibility between cathode and electrolyte, cathode architecture design, interface engineering, correlation between material properties, cathode processing approaches, and performance, as well as the advanced characterization methods used to understand the above correlations . Some perspectives on future development are shared including utilizing in situ and operando characterization tools to better understand dynamic evolution of the cathode/electrolyte interface, adapting artificial intelligence and machine learning to design and optimize cathode structures. The article is aimed to promote research interest on cathode development and advance solid‐state battery technologies.

cathode engineering↗