Results for “flight computers” — Page 49

NASA NTRS2004

Computationally-Efficient Minimum-Time Aircraft Routes in the Presence of Winds

A computationally efficient algorithm for minimizing the flight time of an aircraft in a variable wind field has been invented. The algorithm, referred to as Neighboring Optimal Wind Routing (NOWR), is based upon neighboring-optimal-control (NOC) concepts and achieves minimum-time paths by adjusting aircraft heading according to wind conditions at an arbitrary number of wind measurement points along the flight route. The NOWR algorithm may either be used in a fast-time mode to compute minimum- time routes prior to flight, or may be used in a feedback mode to adjust aircraft heading in real-time. By traveling minimum-time routes instead of direct great-circle (direct) routes, flights across the United States can save an average of about 7 minutes, and as much as one hour of flight time during periods of strong jet-stream winds. The neighboring optimal routes computed via the NOWR technique have been shown to be within 1.5 percent of the absolute minimum-time routes for flights across the continental United States. On a typical 450-MHz Sun Ultra workstation, the NOWR algorithm produces complete minimum-time routes in less than 40 milliseconds. This corresponds to a rate of 25 optimal routes per second. The closest comparable optimization technique runs approximately 10 times slower. Airlines currently use various trial-and-error search techniques to determine which of a set of commonly traveled routes will minimize flight time. These algorithms are too computationally expensive for use in real-time systems, or in systems where many optimal routes need to be computed in a short amount of time. Instead of operating in real-time, airlines will typically plan a trajectory several hours in advance using wind forecasts. If winds change significantly from forecasts, the resulting flights will no longer be minimum-time. The need for a computationally efficient wind-optimal routing algorithm is even greater in the case of new air-traffic-control automation concepts. For air-traffic-control automation, thousands of wind-optimal routes may need to be computed and checked for conflicts in just a few minutes. These factors motivated the need for a more efficient wind-optimal routing algorithm.

Jardin, Matthew R.↗

NASA NTRS2014

Benefits Analysis of Multi-Center Dynamic Weather Routes

Dynamic weather routes are flight plan corrections that can provide airborne flights more than user-specified minutes of flying-time savings, compared to their current flight plan. These routes are computed from the aircraft's current location to a flight plan fix downstream (within a predefined limit region), while avoiding forecasted convective weather regions. The Dynamic Weather Routes automation has been continuously running with live air traffic data for a field evaluation at the American Airlines Integrated Operations Center in Fort Worth, TX since July 31, 2012, where flights within the Fort Worth Air Route Traffic Control Center are evaluated for time savings. This paper extends the methodology to all Centers in United States and presents benefits analysis of Dynamic Weather Routes automation, if it was implemented in multiple airspace Centers individually and concurrently. The current computation of dynamic weather routes requires a limit rectangle so that a downstream capture fix can be selected, preventing very large route changes spanning several Centers. In this paper, first, a method of computing a limit polygon (as opposed to a rectangle used for Fort Worth Center) is described for each of the 20 Centers in the National Airspace System. The Future ATM Concepts Evaluation Tool, a nationwide simulation and analysis tool, is used for this purpose. After a comparison of results with the Center-based Dynamic Weather Routes automation in Fort Worth Center, results are presented for 11 Centers in the contiguous United States. These Centers are generally most impacted by convective weather. A breakdown of individual Center and airline savings is presented and the results indicate an overall average savings of about 10 minutes of flying time are obtained per flight.

NAS based Benefits Analysis↗

NASA NTRS2007

Smart Payload Development for High Data Rate Instrument Systems

This slide presentation reviews the development of smart payloads instruments systems with high data rates. On-board computation has become a bottleneck for advanced science instrument and engineering capabilities. In order to improve the computation capability on board, smart payloads have been proposed. A smart payload is a Localized instrument, that can offload the flight processor of extensive computing cycles, simplify the interfaces, and minimize the dependency of the instrument on the flight system. This has been proposed for the Mars mission, Mars Atmospheric Trace Molecule Spectroscopy (MATMOS). The design of this system is discussed; the features of the Virtex-4, are discussed, and the technical approach is reviewed. The proposed Hybrid Field Programmable Gate Array (FPGA) technology has been shown to deliver breakthrough performance by tightly coupling hardware and software. Smart Payload designs for instruments such as MATMOS can meet science data return requirements with more competitive use of available on-board resources and can provide algorithm acceleration in hardware leading to implementation of better (more advanced) algorithms in on-board systems for improved science data return

Virtex-4↗

NASA NTRS2012

Fly-by-Wire Systems Enable Safer, More Efficient Flight

Using the ultra-reliable Apollo Guidance Computer that enabled the Apollo Moon missions, Dryden Flight Research Center engineers, in partnership with industry leaders such as Cambridge, Massachusetts-based Draper Laboratory, demonstrated that digital computers could be used to fly aircraft. Digital fly-by-wire systems have since been incorporated into large airliners, military jets, revolutionary new aircraft, and even cars and submarines.

Source record↗

NASA NTRS1983

Design, implementation and flight testing of PIF autopilots for general aviation aircraft

The designs of Proportional-Integrated-Filter (PIF) auto-pilots for a General Aviation (NAVION) aircraft are presented. The PIF autopilot uses the sampled-data regulator and command generator tracking to determine roll select, pitch select, heading select, altitude select and localizer/glideslope capture and hold autopilot modes. The PIF control law uses typical General Aviation sensors for state feedback, command error integration for command tracking, digital complementary filtering and analog prefiltering for sensor noise suppression, a control filter for computation delay accommodation and the incremental form to eliminate trim values in implementation. Theoretical developments described in detail, were needed to combine the sampled-data regulator with command generator tracking for use as a digital flight control system. The digital PIF autopilots are evaluated using closed-loop eigenvalues and linear simulations. The implementation of the PIF autopilots in a digital flight computer using a high order language (FORTRAN) is briefly described. The successful flight test results for each PIF autopilot mode is presented.

Broussard, J. R.↗

NASA NTRS1961

Design and Flight Tests of an Adaptive Control System Employing Normal-Acceleration Command

An adaptive control system employing normal-acceleration command has been designed with the aid of an analog computer and has been flight tested. The design of the system was based on the concept of using a mathematical model in combination with a high gain and a limiter. The study was undertaken to investigate the application of a system of this type to the task of maintaining nearly constant dynamic longitudinal response of a piloted airplane over the flight envelope without relying on air data measurements for gain adjustment. The range of flight conditions investigated was between Mach numbers of 0.36 and 1.15 and altitudes of 10,000 and 40,000 feet. The final adaptive system configuration was derived from analog computer tests, in which the physical airplane control system and much of the control circuitry were included in the loop. The method employed to generate the feedback signals resulted in a model whose characteristics varied somewhat with changes in flight condition. Flight results showed that the system limited the variation in longitudinal natural frequency of the adaptive airplane to about half that of the basic airplane and that, for the subsonic cases, the damping ratio was maintained between 0.56 and 0.69. The system also automatically compensated for the transonic trim change. Objectionable features of the system were an exaggerated sensitivity of pitch attitude to gust disturbances, abnormally large pitch attitude response for a given pilot input at low speeds, and an initial delay in normal-acceleration response to pilot control at all flight conditions. The adaptive system chatter of +/-0.05 to +/-0.10 of elevon at about 9 cycles per second (resulting in a maximum airplane normal-acceleration response of from +/-0.025 g to +/- 0.035 g) was considered by the pilots to be mildly objectionable but tolerable.

McNeill, Water E.↗

NASA NTRS1984

Flight crew training technology: A review

The process of flight crew training is emphasized herein. Flight simulators and other training equipment are discussed, but the point is made that such equipment does not constitute the training process in its entirety. The development of flight training technology is traced from the period prior to World War I to the present. Computer generated imagery in flight simulation is addressed.

Caro, P. W.↗

NASA NTRS2001

The Analysis and Modeling of the Deployment of NASA's X-38 Parafoil

NASA is currently working on developing the X-38 Crew Return Vehicle for the Internati6nal Space Station (ISS). The aerodynamics of the X-38 and its enormous 7500 square ft parafoil are extremeJy complicated and must be understood and modeled accurately before the vehicle is actually used for human space flight. A large amount of analysis has been performed on the steady state regions of the flight profile when the parafoil is already open. However, the deployment region of the flight profile has not been analyzed in much depth and is a particularly complicated dynamic flight period. During deployment, the X-38 system has its parafoil open up to its full area in five stages over a period of 20-30 seconds. The vehicle transitions from angles of attack around 90 deg to 0 deg in about two seconds and is extremely dynamic. This paper will detail the analysis work done to generate accurate flight profile characteristics of the deployment from flight data from vehicle test drops. Additionally, a computer simulation tool for steady state flight was modified to analyze and model the parafoil deployment. Eventually, a computer model was produced that generated accurate representations of the parafoil deployment dynamics for the vehicle test drops to date.

Ranier, Chris↗

NASA NTRS1977

Flight simulators. Part 1: Present situation and trends. Part 2: Implications for training

The present situation and developments in the technology of flight simulators based on digital computers are evaluated from the standpoint of training airline flight crews. Areas covered are minicomputers and their advantages in terms of cost, space and time savings, software data packets, motion simulation, visual simulation and instructor aids. The division of training time between aircraft and simulator training and the possible advantages from increased use of simulators are evaluated.

Hass, D.↗

NASA NTRSDate not supplied

Overview of the Subscale RAVEN Flight Controls and Modeling Testbed

The Research Aircraft for eVTOL Enabling TechNologies (RAVEN) Subscale Wind-Tunnel and Flight Test (SWFT) model is a subscale aircraft built for flight dynamics and controls research demonstrated in wind-tunnel and flight-test experiments. The intent of this paper is to provide a summary of past, current, and future efforts being pursued by the RAVEN-SWFT project. Initially, vehicle development guidelines were crafted by a multidisciplinary team to ensure that the RAVEN-SWFT vehicle was well suited for research in multiple areas, including aero-propulsive modeling, flight controls, and autonomy, among others. The vehicle has been used to obtain extensive wind-tunnel data, enabling aero-propulsive model development across the transition flight envelope and validation of computational tools. The vehicle will be used to conduct flight testing in order to evaluate modeling strategies and flight control logic. The RAVEN-SWFT model also serves as a risk reduction activity for a conceptual, full-scale vehicle in the 1000-lb class. The next steps in the project are to successfully demonstrate free flight in hover, transition, forward flight, and the reverse thereof, utilizing custom control laws integrated onto the RAVEN-SWFT avionics hardware. The project intends to publicize all of the geometry, data, and methods in future reports.

eVTOL↗

NASA NTRSDate not supplied

BRAINSTACK – A Platform for Artificial Intelligence & Machine Learning Collaborative Experiments on a Nano-Satellite

As space missions continue to become more ambitious, complex, and distant to Earth, the need for advanced on-board intelligent decision making to guide everything from mission operations to fault detection and recovery has become a major front of space research. While the prevalence of research on such Artificial Intelligence / Machine Learning (AI/ML) modules has exploded, the capacity to experimentally validate such modules in space in a rapid and inexpensive format has not. To this end, the Nano Orbital Workshop (NOW) group at NASA Ames Research Center has been at the forefront of performing initial flight evaluation tests of ‘commercially’ available AI/ML computational platforms via the TechEdSat (TES-n) flight series as part of what is programmatically referred to as the BRAINSTACK. BRAINSTACK will provide an orbital AI/ML evaluation laboratory where computational experiments are pre-loaded into memory prior to launch, and then executed as desired during the mission, with results reported back and program tweaks or new data sets uploaded as needed. Processors selected as part of the BRAINSTACK are of ideal size, packaging, and power consumption for easy integration into a cube satellite structure. These experiments have included the evaluation of small, high-performance GPUs and more recently, neuromorphic processors in LEO operations. Neuromorphic processors are of particular interest due to their superior computational power efficiency over GPUs. The first TES-n flight test of an Intel first-generation Loihi neuromorphic processor launched on January 13, 2022 and continues to operate in orbit despite almost no space environment modifications. The Intel Loihi Gen-1 is characterized by a 14nm 128-core Spiking Neural Network (SNN) able to support on-chip training. This experiment utilized a Loihi packaged in the ‘Kapoho Bay’ USB module, providing a relatively straight-forward interface to the bus avionics system. The Kapoho Bay was in turn managed by a host Intel Pentium single-board computer to handle scheduling of the AI/ML application payloads, and communications with the satellite vehicle manager. The recently released Intel Loihi Gen-2, able to support integer-valued spike payloads and produced using 7nm process, will form part of the basis of the evolving BRAINSTACK in the upcoming three TES-n/NOW flights. Additionally, it is planned to measure the radiation environment these processors experience to understand any degradation or computational artifacts caused by long term space radiation exposure on these novel architectures. This evolving flexible and collaborative environment involving various research teams across NASA and other organizations is intended to be a convenient orbital test platform from which many anticipated future space AI/ML applications may be initially tested.

Artificial Intelligence↗

NASA NTRSDate not supplied

BRAINSTACK – A Platform for Artificial Intelligence & Machine Learning Collaborative Experiments on a Nano-Satellite

As space missions continue to become more ambitious, complex, and distant to Earth, the need for advanced on-board intelligent decision making to guide everything from mission operations to fault detection and recovery has become a major front of space research. While the prevalence of research on such Artificial Intelligence / Machine Learning (AI/ML) modules has exploded, the capacity to experimentally validate such modules in space in a rapid and inexpensive format has not. To this end, the Nano Orbital Workshop (NOW) group at NASA Ames Research Center has been at the forefront of performing initial flight evaluation tests of ‘commercially’ available AI/ML computational platforms via the TechEdSat (TES-n) flight series as part of what is programmatically referred to as the BRAINSTACK. BRAINSTACK will provide an orbital AI/ML evaluation laboratory where computational experiments are pre-loaded into memory prior to launch, and then executed as desired during the mission, with results reported back and program tweaks or new data sets uploaded as needed. Processors selected as part of the BRAINSTACK are of ideal size, packaging, and power consumption for easy integration into a cube satellite structure. These experiments have included the evaluation of small, high-performance GPUs and more recently, neuromorphic processors in LEO operations. Neuromorphic processors are of particular interest due to their superior computational power efficiency over GPUs. The first TES-n flight test of an Intel first-generation Loihi neuromorphic processor launched on January 13, 2022 and continues to operate in orbit despite almost no space environment modifications. The Intel Loihi Gen-1 is characterized by a 14nm 128-core Spiking Neural Network (SNN) able to support on-chip training. This experiment utilized a Loihi packaged in the ‘Kapoho Bay’ USB module, providing a relatively straight-forward interface to the bus avionics system. The Kapoho Bay was in turn managed by a host Intel Pentium single-board computer to handle scheduling of the AI/ML application payloads, and communications with the satellite vehicle manager. The recently released Intel Loihi Gen-2, able to support integer-valued spike payloads and produced using 7nm process, will form part of the basis of the evolving BRAINSTACK in the upcoming three TES-n/NOW flights. Additionally, it is planned to measure the radiation environment these processors experience to understand any degradation or computational artifacts caused by long term space radiation exposure on these novel architectures. This evolving flexible and collaborative environment involving various research teams across NASA and other organizations is intended to be a convenient orbital test platform from which many anticipated future space AI/ML applications may be initially tested.

Artificial Intelligence↗

NASA NTRSDate not supplied

A High-Performance Computing GNSS-aware Path Planning Algorithm for Safe Urban Flight Operations

The emergence and development of advanced technologies and vehicle types have created a growing demand for new forms of flight operations. These new and increasingly complex operational paradigms, such as Advanced and Urban Air Mobility (AAM/UAM), present regulatory authorities and the aviation community with several design-and-implementation challenges – particularly for highly autonomous vehicles. An overarching and daunting task is to develop protocols that can integrate these operations without compromising safety or disrupting traditional airspace operations. A shift toward a more predictive, autonomous, risk mitigation capability becomes critical to meet this challenge. This paper proposes and evaluates a computationally-efficient path planning approach to perform pre-flight planning and autonomous in-flight re-routing to minimize exposures to selected hazards. In our evaluation, hazards associated with degraded and missing critical GPS navigation data are considered. In this paper, we first present a high-performance computing path planning approach based on an adapted Bellman-Ford algorithm, developed in the CUDA programming language. Using the adapted path planning algorithm, we test this algorithm when encountering issues with GPS quality, and deliver an implementation that can produce flight paths that minimize exposure to risks, while maintaining a low computational burden. In our evaluation, the computation of periodic and aperiodic path updates are evaluated, prioritizing specific events as triggers for updates, based on changes to satellite availability. These critical events can lead to significant exposure to navigational hazards if not dealt with correctly.

GNSS↗

NASA NTRSDate not supplied

A High-Performance Computing GNSS-aware Path Planning Algorithm for Safe Urban Flight Operations

The emergence and development of advanced technologies and vehicle types have created a growing demand for new forms of flight operations. These new and increasingly complex operational paradigms, such as Advanced and Urban Air Mobility (AAM/UAM), present regulatory authorities and the aviation community with several design-and-implementation challenges – particularly for highly autonomous vehicles. An overarching and daunting task is to develop protocols that can integrate these operations without compromising safety or disrupting traditional airspace operations. A shift toward a more predictive, autonomous, risk mitigation capability becomes critical to meet this challenge. This paper proposes and evaluates a computationally-efficient path planning approach to perform pre-flight planning and autonomous in-flight re-routing to minimize exposures to selected hazards. In our evaluation, hazards associated with degraded and missing critical GPS navigation data are considered. In this paper, we first present a high-performance computing path planning approach based on an adapted Bellman-Ford algorithm, developed in the CUDA programming language. Using the adapted path planning algorithm, we test this algorithm when encountering issues with GPS quality, and deliver an implementation that can produce flight paths that minimize exposure to risks, while maintaining a low computational burden. In our evaluation, the computation of periodic and aperiodic path updates are evaluated, prioritizing specific events as triggers for updates, based on changes to satellite availability. These critical events can lead to significant exposure to navigational hazards if not dealt with correctly.

GNSS↗

NASA NTRS1974

Implementation of hydrologic models at Goddard Space Flight Center

Major watershed simulation models were implemented on the computer system at NASA Goddard Space Flight Center, and their operation was verified. Historical and physiographic data were acquired for two Maryland river basins (Monocasy River above Jug Bridge and Patuxent River near Laurel, Maryland) and the models were calibrated to simulate them. GSFC personnel were instructed in model operation after the models were implemented.

Source record↗

NASA NTRS1989

Transonic Symposium: Theory, Application and Experiment, volume 2

Papers presented at the Transonic Symposium are compiled. The following subject areas are covered: National Transonic Facility status; transonic aerodynamics of slender wing-body configuration; laminar flow flight experiments; laminar flow wind tunnel experiments; computational support of X-29A flight experiment; transition location on a clean-up glove installed on a F-14 aircraft; and design studies for a laminar glove for the X-29 aircraft.

Foughner, Jerome T., Jr.↗

NASA NTRSDate not supplied

Design of a Crossflow Attenuated Natural Laminar Flow Flight Test Article

This abstract includes preliminary information on the computational design and analysis of a flight test article. The flight test aims to experimentally validate the new Crossflow Attenuated Natural Laminar Flow (CATNLF) design method in a flight environment. The CATNLF design method uses geometry shaping to produce specific pressure distributions that enable laminar flow on vehicle components with high sweep and high Reynolds numbers by attenuating the crossflow growth that typically leads to premature transition on such components. The flight test article design is scheduled to be completed at the end of 2019, with model fabrication beginning in early 2020.Design results presented in this abstract are representative of the final test article. The final paper will be updated to include the finalized test article geometry and analysis.

Michelle N. Lynde↗

NASA NTRS1992

Identification of aerodynamic coefficients using computational neural networks

Precise, smooth aerodynamic models are required for implementing adaptive, nonlinear control strategies. Accurate representations of aerodynamic coefficients can be generated for the complete flight envelope by combining computational neural network models with an Estimation-Before-Modeling paradigm for on-line training information. A novel method of incorporating first-partial-derivative information is employed to estimate the weights in individual feedforward neural networks for each aerodynamic coefficient. The method is demonstrated by generating a model of the normal force coefficient of a twin-jet transport aircraft from simulated flight data, and promising results are obtained.

Linse, Dennis J.↗