Search NASA⌕ Search

SEARCH · Search NASA

Results for “fuel reprocessing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Comparison of Extended and Accelerated VOG Tests

The reprocessing of used nuclear fuel would release volatile radionuclides into the off-gas streams of a processing plant, including ¹²⁹I. The dissolver off-gas and more dilute vessel off-gas streams (VOG) must both be targeted when mitigating ¹²⁹I environmental release because each contains some amount of iodine. Iodine-129 will likely be found as elemental iodine (I₂) and methyl iodide (CH₃I) in these off-gas streams. Reduced silver-exchanged mordenite (AgZ or Ag⁰Z) has been investigated as a potential sorbent for iodine abatement and is studied here under prototypic VOG conditions. Because of the relatively low iodine abundance and high flow rates of the VOG, total iodine concentrations are expected to be in the parts per billion range. Thus, VOG experiments need to run for extended durations at low concentrations to reach sorbent saturation. Because the sorbent will be exposed to oxidizing gas streams for extended periods of time, aging effects and sorbent degradation need to be considered when designing a sorbent-based abatement system. Three sets of experiments were performed with the aim of determining how the adsorption of iodine by AgZ is affected by differing test durations and gas compositions. The first tested the capacity of sorbent aged for 8 months under a humid air stream. The second tested differences in sorbent capacity and mass transfer zone (MTZ) length during high-concentration (1200 ppb v ) CH₃I loading in a humid nitrogen gas (N₂) stream and a humid air gas stream over 28 days. The third tested sorbent capacity and MTZ length during low concentration (< 200 ppb v ) CH₃I and I₂ loading in a humid air stream over 9 months. The results of these tests suggest that AgZ capacity drops by ~50% after 1 month of aging, by ~60% after 2 months of aging, and then does not continue to decrease significantly at up to 8 months of aging. One-month aging tests that compared N₂ and air as the gas stream diluent resulted in similar maximum loading capacities and overall loading curves, indicating that the effects of aging cannot be mitigated by avoiding air as the balance gas. The 9-month extended VOG tests did not result in clear sorbent saturation at the inlet, but it can be inferred using an assumption of a maximum capacity of 45 mg I/g AgZ. Applying this assumption, then the MTZ of CH₃I is 12.8 cm, and the MTZ of I₂ is 12.4 cm. These results are similar to previous tests. Comparisons to tests completed at Idaho National Laboratory suggest that the CH₃I MTZ may be dependent on concentration. Future work should re-evaluate the design of the VOG iodine capture system with this updated data and should seek to understand fundamental characteristics of CH₃I adsorption by AgZ, such as the effect of concentration, gas velocity, and gas composition.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Actinide N-Donor Thermodynamics: Expanding the f-element Covalency Dialogue. Final report

Resolving the chemistry and physics of f-electrons is one of the grand challenges of science for energy technology. A central component of this challenge is describing covalency in actinide-ligand interactions. Crystallography, x-ray spectroscopy and computational techniques have provided reasonable, and in some cases remarkable, support for covalency in actinide-ligand interactions. Courtesy the quality of the results obtained, a significant portion of the covalency dialogue has been forwarded through solid-state and computational studies of the more stable actinides (Th, U, Pu, Np). However; recent reports have questioned whether covalency in actinide interactions increases or decreases across the series. Examination of less-stable trans-actinides (Am, Cm, Bk, Cf and Es) by the aforementioned approaches can be rapidly limited due to material availability, radiological hazards and experimental data to validate computational models. Furthermore, limited thermodynamic data exists to confirm covalency in actinide solution phase interactions that are highly relevant to the remediation and reprocessing of used nuclear fuel. The best-defined interactions of actinides with soft donors in aqueous solutions involve (poly)aminopolycarboxylate (APC) ligands. The chelate effect and binding affinity with the acetic acid APCs subgroups encourages amine interactions with the actinide metal center. In the absence of these factors, amine interactions with actinides are too weak to overcome the protective hydration shell of the dissolved ion. The ability for APCs to force actinide interactions with soft nitrogen donors (as defined by Pearson’s Hard Soft Acid Base theory) encourages the application of these ligands in a variety of processes for actinide recovery from nearly chemically identical lanthanides. The ability to functionalize the amine center of the ligand in a variety of capacities (adding additional amine groups, exchanging the conventional acetate group for an acetate group, etcetera), allows for the APC ligand to serve as a thermodynamic probe for actinide-nitrogen interactions. Perhaps the single most significant breakthrough during the previous funding cycle was the observation that covalency for the transplutonium part of the actinide series can be increasingly influenced with energy degeneracy driven covalency as the actinides become heavier. This was observed most predominantly with dipicolinic acid, but extensions of f-orbital degeneracy were found to affect aliphatic aminopolycarboxylate-actinide complexes through einsteinium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis of Organoiodide Adsorption Mechanisms

If the United States were to engage in the reprocessing of used nuclear fuel, radioactive iodine must be removed from multiple plant off-gas streams to comply with governing regulations. One of these streams is the vessel off-gas (VOG), which arises from the separations process and is expected to contain iodine in primarily organic iodine forms and at parts-per-billion concentrations. The relative lack of knowledge surrounding organic iodine removal from the VOG prompted the US Department of Energy’s Office of Nuclear Energy to initiate experimental efforts targeted at understanding organic iodide removal from prototypic VOG streams. At Oak Ridge National Laboratory (ORNL), this effort has focused on developing a comprehensive understanding of iodine removal from VOG streams by using silver-based sorbents. An important aspect of this testing is developing an understanding of how the sorption of methyl iodide (CH 3 I), the most studied organic iodide species to date, compares with the sorption of other volatile organic iodide species potentially present in the VOG. The work presented here reflects initial testing that will continue to be developed, and final results will be incorporated into an end-of-year report that details a multiyear testing campaign designed to understand iodine mitigation from VOG streams. The goal of these experiments was to determine whether similar reaction pathways govern both CH 3 I and iodobutane (C 4 H 9 I) sorption onto silver mordenite (AgZ), a common silver-based iodine sorbent. More specifically, the authors hypothesized that the sorption of C 4 H 9 I by AgZ will result in the formation of butanol (C 4 H9OH). Effluent monitoring of CH 3 I sorption testing has confirmed methanol production, but analogous monitoring of effluents from C 4 H 9 I sorption studies has not been performed. A series of tests was completed to test this hypothesis with the aim of detecting C 4 H 9 OH downstream of the AgZ bed. Test conditions varied the bed depth, gas stream humidity, and bed temperature post sorption. The effluent gas stream downstream of the AgZ bed was sampled by using gas-tight syringes, and these samples were analyzed by a gas chromatograph coupled to a mass spectrometer. Thin bed C 4 H 9 I tests conducted at -65 and 0°C dew points did not result in C 4 H 9 OH detection in the effluent. This suggests that the sorption mechanism and subsequent reactions could be different from those observed for CH 3 I. The sorption testing continues; additional results will be included in final end-of-year report and will increase the fundamental understanding of organic iodide sorption by AgZ from VOG streams.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Solvent Recovery and Management at the Savannah River Site H-Canyon Facility

NIOWAVE, Inc. is a domestic supplier of medical and industrial isotopes from uranium and radium. The Savannah River National laboratory (SRNL) is currently providing support to NIOWAVE, which plans to deploy a superconducting electron linear accelerator (LINAC) to fission uranium for Mo-99 production without the need for a nuclear reactor or HEU. The uranium from the Mo-99 production targets will be purified using a modified PUREX (Plutonium Uranium Reduction Extraction) solvent extraction process to recover the uranium in the product stream. The uranium will then be precipitated as an oxalate which is calcined to U 3 O 8 to fabricate pellets for new Mo-99 targets. In previous support provided to NIOWAVE, the SRNL demonstrated a solvent washing process to remove degradation products from the tributyl phosphate (TBP) solvent used in the modified PUREX process under development for uranium recovery. To supplement this technology demonstration, NIOWAVE requested the SRNL to provide summary information on the solvent recovery and management activities which are used at the Savannah River Site (SRS) H-Canyon facility. An existing reference document for the reprocessing of irradiated HEU fuels at the SRS was used as the primary reference for the solvent management activities; although, other reference documents were used to provide supplementary information. The information provided includes a brief summary of the solvent degradation issues which have been observed in the H-Canyon solvent extraction cycles and resulting process safety concerns. The solvent recovery processes for the three cycles of solvent extraction used in the H-Canyon were subsequently described including the process equipment which consists of the continuous and batch solvent washers, pumps, and tanks. A final section is provided on the monitoring and analysis of solvent quality based on the previous work performed at the SRNL for NIOWAVE and past research and development activities performed to support the solvent extraction processes in both the SRS F-Canyon and H-Canyon facilities.

07 ISOTOPE AND RADIATION SOURCES↗

Iodine Capture Studies of Silver Mordenite and Novel Alternative Metal Sorbents

Radioiodine is one of the radionuclides of concern when considering reprocessing of used nuclear fuel (UNF). It is expected to be released primarily in the dissolver off-gas (DOG) stream. Sorbents that target I 2 removal from a UNF processing off gas must perform efficiently under elevated temperatures in the presence of water vapor and nitrogen oxide gasses (NOx). Many studies have been conducted that examine the adsorption of iodine species in the presence of NOx gases through reduced silver-exchanged mordenite (Ag 0 Z), a zeolite mineral. This study characterizes the effects of iodine, water vapor, and nitrogen dioxide on the adsorption of I 2 by Ag 0 Z at lower temperatures suitable for comparison with novel Cu- and Bi- bearing sorbents which offer a non-RCRA alternative. When exposed to ‘harsh’ conditions such as I 2 , H 2 O, and NO 2 vapors carried by air, Cu 2 S-polyacrylonitrile (PAN) is more efficient than Ag 0 Z and all other novel sorbents, providing with 11% I capture efficiency. However, under ‘ideal’ conditions in which I 2 is carried by dry air), Ag 0 Z is more efficient than Cu 2 S-PAN and other novel sorbents, providing 74% I capture efficiency. To investigate this result and the overall performance of all sorbents tested, several characterization techniques were employed, including thermal gravimetric analysis, scanning electron microscopy – electron dispersion X-Ray spectroscopy, powder X-ray diffraction, and X-ray photoelectron spectroscopy. These techniques are discussed within this report. This document also includes a design and test plan update from Idaho National Laboratory as the next step in testing the high performing sorbents from thin-bed tests carried out by Oak Ridge National Laboratory.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Aluminophosphate Waste Forms for Immobilizing Cations from Electrochemical Salt Wastes

This report provides experimental details and results of evaluating aluminophosphate waste forms for treating and immobilizing the salt cations from salt wastes generated during electrochemical reprocessing of used nuclear fuel. In the waste form process for these materials, chloride salt streams are reacted with NH 4 H 2 PO 4 , the chlorine is removed from the salts and driven off as NH 4 Cl (a solid condensate that can be captured), and then the product can be vitrified in conjunction with glass-forming chemicals (e.g., Fe 2 O 3 , Al 2 O 3 ) to create a high-durability waste form. This study was initiated with some literature review on aluminophosphates containing high alkali oxide content and some of this information is summarized in this report. Following literature review, three new samples were synthesized where two contained Fe 2 O 3 +Al 2 O 3 (i.e., samples G3 and G5 ) and one was only Al 2 O 3 (Fe 2 O 3 -free) (i.e., sample G6 ). In addition to these samples, G1 was also made, which is the baseline reference waste form referred to as DPF5-336 (made without Al 2 O 3 ). Samples G1, G3, G5, and G6 had phases of Li 3 Fe 2 (PO 4 ) 3 (likely), monazite (below XRD detection limits), AlPO 4 , and AlPO 4 , respectively. Characterizations on these materials included optical images, scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction. These samples were shipped to Argonne National Laboratory for chemical durability testing. Depending on how the samples perform in these tests, an additional phase of aluminophosphate formulations could be designed and tested. This report completes the milestone M4FT-23PN030104041 with details provided in Appendix B.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Investigating the Durability of Iodine Waste Forms in Dilute Conditions

To prevent the release of radioiodine during the reprocessing of used nuclear fuel or in the management of other wastes, many technologies have been developed for iodine capture. The capture is only part of the challenge as a durable waste form is required to ensure safe disposal of the radioiodine. This work presents the first durability studies in dilute conditions of two AgI-containing waste forms: hot-isostatically pressed silver mordenite (AgZ) and spark plasma sintered silver-functionalized silica aerogel (SFA) iodine waste forms (IWF). Using the single-pass flow-through (SPFT) test method, the dissolution rates respective to Si, Al, Ag and I were measured for variants of the IWFs. By combining solution and solid analysis information on the corrosion mechanism neutral-to-alkaline conditions was elucidated. The AgZ samples were observed to have corrosion preferentially occur at secondary phases with higher Al and alkali content. These phases contained a lower proportion of I compared with the matrix. The SFA samples experienced a higher extent of corrosion at Si-rich particles, but an increased addition of Si to the waste led to an improvement in corrosion resistance. The dissolution rates for the IWF types are of similar magnitude to other Si-based waste form materials measured using SPFT.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of the Actinide-Lanthanide Separation (ALSEP) Process

Separating the minor actinide elements (Am and Cm) from acidic high-level raffinates arising from the reprocessing of irradiated nuclear fuel is an important step in closing the nuclear fuel cycle. Most proposed approaches to this problem involve two solvent extraction steps: 1) co-extraction of the trivalent lanthanides and actinides, followed by 2) separation of the actinides from the lanthanides. The objective of our work is to develop a single solvent-extraction process for isolating the minor actinide elements. We report here a solvent containing N,N,N',N'-tetra(2 ethylhexyl)diglycolamide (T2EHDGA) combined with 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (HEH[EHP]) that can be used to separate the minor actinides in a single solvent-extraction process. T2EHDGA serves to co-extract the trivalent actinide and lanthanide ions from nitric acid solution. Switching the aqueous phase chemistry to a citrate buffered solution of N-(2-hydroxyethyl)ethylenediamine-N,N',N'-triacetic acid at pH 2.5 to 4 results in selective transfer of the actinides to the aqueous phase, thus affecting separation of the actinides from the lanthanides. Separation factors between the lanthanides and actinides are approximately 20 in the pH range of 3 to 4, and the distribution ratios are not highly dependent on the pH in this system.

actinide separation↗

Application of a Triple Bubbler Sensor for Determining the Density, Surface Tension, and Depth in Molten Salts

Electrochemical (i.e. pyroprocessing) technology is being widely studied throughout the world as a potential alternative to aqueous reprocessing of spent nuclear fuel (SNF). Central to this process is the electrorefiner (ER), in which the useful uranium in the SNF is electrochemically transported through a molten salt electrolyte to a cathode for later recovery. As part of this process, uranium, plutonium, and other actinides accumulate in the ER salt over time. Material accountancy and safeguards of these special nuclear material buildups in near real-time is a significant challenge due to the elevated processing temperatures, remote operation within a hotcell, and high radiation fields. Analytical techniques outside of the hotcell can be used to provide the SNM concentrations of salt samples from the ER. However, determining the actual mass of these materials in the ER presents a significant challenge because the density and volume within the vessel is largely unknown. The Idaho National Laboratory (INL) has developed a triple bubbler sensor capable of determining the density, surface tension, and depth of a fluid in near real-time. Previous experiments in aqueous media has shown that the sensor is capable of determining the density, surface tension and depth with accuracies on the order of 0.2%. The goal of this current work is to test the sensor in several molten salt media to calibrate and validate the triple bubbler. Experiments have been performed in LiCl-KCl eutectic salt. Calibration factors were 1.0015 and 1.26 for density and surface tension, respectively. With the above calibration factors applied, the depth of the salt in the test vessel was determined to within 0.4%. These results indicate that the triple bubbler sensor has the potential to accurately (less than 1% uncertainty) determine the density, surface, tension, and depth of the ER salt in near real-time. The triple bubbler sensor designed at INL can significantly enhance the material accountancy, safeguards, and process monitoring of the electrochemical processing of SNF.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Radiological Degradation of Tetraoctyl Diglycolamide in n-Alkyl Solvents: Influence of Solvent Ionization Potential

Reprocessing of used nuclear fuel reduces the requirements for long-term storage repositories. Cost-efficient processes depend on knowledge of radiation effects, but gaps occur in understanding how radiation results in the degradation of fuel separation molecules. This project investigates the influence of different n-alkyl solvents on the radiolytic fragmentation behavior of N,N,N',N'-Tetraoctyl-3-oxapentane-1,5-diamide (TODGA), a promising ligand for extraction of the lanthanides and minor actinides from dissolved nuclear fuel. Findings from this work suggest a linkage between the ionization potential of the solvent and the degradation products observed in the resulting mass spectrum.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Crystalline Aluminosilicates for Radionuclide Remediation

Crystalline aluminosilicates have a wide range of applications such as media for the capture and/or immobilization of radionuclides. Several different types of metal-exchanged zeolites have been successfully demonstrated as effective sorbents for gaseous, aqueous, or solid-state capture and immobilization of radionuclides including iodine [e.g., I2(g), CH3I(g)], xenon, krypton, radium (e.g., 226Ra and 228Ra), selenium (e.g., 79Se6+), technetium (e.g., 99TcO4-), strontium (e.g., 90Sr2+), cesium (e.g., 135Cs+, 137Cs+), mixed alkali halide streams (i.e., iodide and chloride salts), and actinides (e.g., U6+, Th4+). These zeolites include sodalite (SOD), mordenite (MOR or Z-type), faujasite (FAU), Linde type-A (LTA), cancrinite (CAN), gismondine (GIS), and heulandite (or clinoptilolite) (HEU). The structural building blocks of these seven materials vary from cages (e.g., a-cages, ß-cages, e-cages) to channels linking various cage types and these are mostly comprised of aluminosilicates. This chapter will delve into the crystallographic differences between these framework materials and provide a brief overview of literature data where these seven crystalline aluminosilicates have been utilized for the capture and/or immobilization of radionuclides. Metal-exchanged zeolites (e.g., MOR, FAU, LTA) have often been the source of study for gaseous capture of iodine where the more promising compositions include Ag-exchanged sorbents; these types of materials can be made in a variety of robust forms including berl saddles and extrudates. Sodalite can be used as an immobilization strategy for halide waste streams (e.g., Cl, I), including those from electrochemical reprocessing of used nuclear fuel, as well as TcO4–. Cancrinite has been demonstrated to enhance sorption capacity of sediments for several problematic ionic radionuclides including Cs+, SeO42–, and TcO4–. Actinides such as U6+ and Th4+ have been successfully captured from solutions using MOR, FAU, LTA, and HEU-type aluminosilicates. Finally, mixtures of aluminosilicates have been included in a set of zeolite materials that show promise as sorbents for 226Ra and 228Ra removal from mine waters.

zeolites, aluminosilicates, radionuclide remediati↗

The Future U.S. Energy Infrastructure - And Who Will Do the Work?

This paper identifies the current state and future implications of power generating capacity in the U.S. It also discusses workforce planning and hiring options to support the anticipated staffing needs that will be required to construct and eventually operate these new plants. The Energy Information Administration forecasts that electricity consumption will increase approximately 40% by 2030. Therefore, new power plants, equivalent to 730 new base-load 400-megawatt power plants, will be required to ensure adequate electricity supplies for the future. Of the 104 operating nuclear plants in the U.S., a majority of them have already been operating approximately 20 to 30 years, and even longer. Over the next 50 years, many of these plants, both nuclear and non-nuclear, will have reached their maximum design basis operating lifetimes. Relatively young plants achieving 20 years of operation today will be completing a 40-year run by the year 2028 and a 70-year run, if allowed to do so, by the year 2058. Furthermore, as the oldest 'baby-boomers' begin retiring over the next several years, the lack of an experienced workforce may indirectly affect the needed workforce required to support the U.S. energy infrastructure from new construction through the safe operation of existing and next-generation nuclear plants. With the prospects of companies needing to hire 'passive' candidates, (i.e., experienced '40-something' workers who are not necessarily looking for a job, but are willing to discuss a career move if it offers a significant upside opportunity) to fill employment vacancies, there are 10 factors to consider when evaluating potential opportunities: 1) the job fit; 2) the job stretch; 3) opportunity for future learning and growth; 4) the chance to make an impact; 5) the hiring manager as mentor; 6) the quality of the team; 7) the company's prospects and strategy; 8) the company culture; 9) work/life balance; and 10) compensation and benefits. If the company is clearly not superior on the first nine factors, the candidate will likely reject the offer. Furthermore, if history serves as a guide to the future, failing to follow through with a cohesive, well-defined energy strategy offered by new plant construction will likely produce the same results following the indefinite deferral to reprocess commercial spent nuclear fuel. Since the deferral in 1977, billions of dollars have been spent, while producing few, if any, substantial results. The significance of maintaining the U.S. energy infrastructure and hiring a combination of both newly-graduated and experienced employees to perform the work must be recognized and acknowledged today to ensure that we have adequate, affordable, and reliable electricity for the future. If these programs fail, expect these scenarios to be repeated again over the next 30 years, instead of achieving energy independence - a truly substantial result. (authors)

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Prediction of the safety level to an installation of the tritium process through predictive maintenance

The safety level for personnel and environment to a nuclear installation is given in generally by the technological process quality of operation and maintenance and in particular by a lot of technical, technological, economic and human factors. The maintenance role is fundamental because it has to quantify all the technical, economic and human elements as an integrated system for it creates an important feedback for activities concerning the life cycle of the nuclear installation. In maintenance activities as in any dynamic area, new elements appear continuously which, sometimes require new approaches. The theory of fuzzy logic and the software LabVIEW supplied to the Nuclear Detritiation Plant (NDP) is part of National Research and Development Inst. for Cryogenics and Isotopic Technologies-ICIT, Rm.Valcea, used for predictive maintenance to assure safety operation. The final aim is to achieve the best practices for maintenance of the Plant that processes tritium. (authors)

07 ISOTOPE AND RADIATION SOURCES↗

A micro hot test of the Chalmers-GANEX extraction system on used nuclear fuel

In the present study, a 'micro hot test' has been performed using the Chalmers-GANEX (Group Actinide Extraction) system for partitioning of used nuclear fuel. The test included a pre-extraction step using N,N-di-2- ethylhexyl-butyramide (DEHBA) in n-octanol to remove the bulk part of the uranium. This pre-extraction was followed by a group extraction of actinides using the mixture of TBP and CyMe{sub 4}-BTBP in cyclohexanone as suggested in the Chalmers-GANEX process, and a three stage stripping of the extracted actinides. Distribution ratios for the extractions and stripping were determined based on a combination of γ- and α-spectrometry, as well as ICP-MS measurements. Successful extraction of uranium, plutonium and the minor actinides neptunium, americium and curium was achieved. However, measurements also indicated that co-extraction of europium occurs to some extent during the separation. These results were expected based on previous experiments using trace concentrations of actinides and lanthanides. Since this test was only performed in one stage with respect to the group actinide extraction, it is expected that multi stage tests will give even better results. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Current status of research and development program for characterizing fuel debris at Fukushima Daiichi NPS by JAEA

Japan Government and TEPCO submitted a research road map for decommissioning Fukushima Daiichi Nuclear Power Plant. Two projects about debris are in progress: 'Assessment of simulated fuel debris characteristics' and 'Development of technologies for the processing of fuel debris'. The major results concerning the first project are the following 4 points. First, it was suggested that typical phase of oxide of fuel debris is (U,Zr)O{sub 2} and that of metal is Fe{sub 2}(Zr,U) by thermodynamic calculation. Secondly, important properties of fuel debris for developing defueling tools were identified as shape, size, density, hardness, elastic modulus, fracture toughness, thermal conductivity, specific heat (heat capacity), and melting point. Thirdly, the influence of seawater salt and B{sub 4}C/SUS to characteristics of debris was found, such as deposition of magnesium oxide crystal on the surface of fuel debris. The Influence of Pu to thermal properties of fuel debris was found, such as the increase of melting point. Concerning the second project, the major results are the following. First, a draft of the whole image of scenarios was developed. Secondly, the alkaline resolution method using Na{sub 2}O{sub 2} is most likely to be applied as a part of analysis technologies. Thirdly, it was shown that a part of fuel debris rich in U might be soluble in nitric acid. Fourthly, it was shown that all pyrochemical processes examined have potential to be applied for treating fuel debris. The results of the projects will contribute to the decommissioning program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Waste Determination Equivalency - 12172

The Savannah River Site (SRS) is a Department of Energy (DOE) facility encompassing approximately 800 square kilometers near Aiken, South Carolina which began operations in the 1950's with the mission to produce nuclear materials. The SRS contains fifty-one tanks (2 stabilized, 49 yet to be closed) distributed between two liquid radioactive waste storage facilities at SRS containing carbon steel underground tanks with storage capacities ranging from 2,800,000 to 4,900,000 liters. Treatment of the liquid waste from these tanks is essential both to closing older tanks and to maintaining space needed to treat the waste that is eventually vitrified or disposed of onsite. Section 3116 of the Ronald W. Reagan National Defense Authorization Act of Fiscal Year 2005 (NDAA) provides the Secretary of Energy, in consultation with the Nuclear Regulatory Commission (NRC), a methodology to determine that certain waste resulting from prior reprocessing of spent nuclear fuel are not high-level radioactive waste if it can be demonstrated that the waste meets the criteria set forth in Section 3116(a) of the NDAA. The Secretary of Energy, in consultation with the NRC, signed a determination in January 2006, pursuant to Section 3116(a) of the NDAA, for salt waste disposal at the SRS Saltstone Disposal Facility. This determination is based, in part, on the Basis for Section 3116 Determination for Salt Waste Disposal at the Savannah River Site and supporting references, a document that describes the planned methods of liquid waste treatment and the resulting waste streams. The document provides descriptions of the proposed methods for processing salt waste, dividing them into 'Interim Salt Processing' and later processing through the Salt Waste Processing Facility (SWPF). Interim Salt Processing is separated into Deliquification, Dissolution, and Adjustment (DDA) and Actinide Removal Process/Caustic Side Solvent Extraction Unit (ARP/MCU). The Waste Determination was signed by the Secretary of Energy in January of 2006 based on proposed processing techniques with the expectation that it could be revised as new processing capabilities became viable. Once signed, however, it became evident that any changes would require lengthy review and another determination signed by the Secretary of Energy. With the maturation of additional salt removal technologies and the extension of the SWPF start-up date, it becomes necessary to define 'equivalency' to the processes laid out in the original determination. For the purposes of SRS, any waste not processed through Interim Salt Processing must be processed through SWPF or an equivalent process, and therefore a clear statement of the requirements for a process to be equivalent to SWPF becomes necessary. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Effect of Kr-85 Decay to Rb-85 on Waste Forms - 17105

Krypton-85 (Kr-85) is a volatile radionuclide released during the reprocessing of used nuclear fuel (UNF). Prior to discharge of process off-gas streams to the environment, removal of Kr-85 is required to meet emission regulations. Once removed from the off-gas streams, Kr (containing stable Kr in addition to Kr-85) must be placed in storage until the Kr-85 has decayed to levels such that its potential release would meet regulatory guidelines. The current method of storage is high-pressure metal canisters. Historically, concerns have been expressed that the decay product of Kr-85, Rubidium-85 (Rb-85), could cause corrosion and weakening in the canisters that would ultimately lead to premature failure and release of Kr-85. Alternate methods and materials, such as matrix isolation in a vapor deposited metal and immobilization in zeolites, have been investigated as storage approaches for Kr. However, even these storage methods may become compromised due to the chemical effects of Rb-85 arising from the decay of Kr-85. A review was conducted of the available literature to examine topics relevant to the effects of Rb on the long-term storage of Kr-85, examine the source terms in the context of this concern, and suggest a path forward to resolve outstanding knowledge gaps. In the course of this analysis, several knowledge gaps were identified. Examples include: o The use of solid sorbents to potentially permit more Kr-85-bearing gas to be loaded into canisters, either at the pressures used in the current method or at significantly lower pressures. o A cost-to-benefit analysis is needed to ascertain the practicality of manufacturing waste forms for Kr-85 storage with solid sorbents. o The effects of radiation and chemical transmutation in solid sorbents or matrices for this application are virtually unknown. o Fundamental data are needed on corrosion rates and mechanisms as functions of Rb concentration, storage temperature, etc., for various storage approaches (e.g., as compressed gas or encapsulated in a getter material) and storage container materials. The present analysis focused on the available information regarding storage of Kr-85 in high-pressure containers. It was judged unlikely that such containers would be compromised by corrosion from the Rb decay product, especially if the Kr recovery operations result in a gas composition with very low oxygen content. However, this conclusion should be revisited based on preliminary data gathered from analysis of legacy Kr waste forms. These legacy waste forms are a result of experiments conducted at Idaho National Laboratory over 30 y ago and have been stored for more than three Kr-85 half-lives. Evaluation of these forms indicates significant corrosion, the cause of which has not been conclusively determined. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Progress in Defining the UK Highly Active Storage Tanks POCO Strategy - 16134

In the UK Highly Active (HA) waste is stored in stainless steel tanks prior to encapsulation in glass in one of three operating vitrification plants. Significant progress has been made in recent years towards the reduction in the volume of HA Liquor (HAL) stored in these tanks and a number of the tanks are now operating at heel levels. As a result, a strategy is being developed to carry out Post Operational Clean Out (POCO) of some tanks while reprocessing operations continue, thus enabling accelerated and more cost effective clean-up of these HA facilities. This paper, and subsequent conference presentation, will highlight some of the key aspects of this strategy, including a description of the challenges and progress made so far to help facilitate the clean-up mission without having a detrimental effect on ongoing reprocessing operations. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗