Search NASA⌕ Search

SEARCH · Search NASA

Results for “liquid interface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

The formation of lunar glasses

The work investigates experimentally the conditions required to form glasses out of a number of lunar compositions. Viscous flow and crystallization behavior of several compositions were studied over a wide range of temperature. These data exhibit the form generally found for glass-forming liquids. Combining growth rate with viscosity data, the fraction of preferred growth sites on the crystal-liquid interfaces is found to increase with increasing undercooling for all lunar compositions. The detailed forms of the kinetic data are predicted by recent computer simulations of crystal growth. Calorimetry studies indicate that lunar orange soil was formed under conditions of much slower cooling rate than 1000 deg K per sec.

Uhlmann, D. R.↗

RF shaping of silicon ribbon

Electromagnetic force generated by radiofrequency coil is used to shape molten silicon. Shaping coil surrounds melt near solid-liquid interface and induces current in surface region of melt nearly equal to but opposite coil current.

Pelhank, D. A.↗

Analysis of surface tension driven flow in floating zone melting

Surface tension driven flow in a cylindrical melt suspended between two rods was investigated by numerical solution of the steady state differential equations for heat and momentum transfer. Radiation heating and electron beam heating were considered approximately. For small values of the driving force, one rotating ring was formed in the top half of the zone, and its mirror image in the bottom half. At larger driving forces, secondary cells form which probably would undergo oscillatory motion. The influence of Prandtl number, zone movement, and buoyancy on the convection was also studied. The primary resistance to mass transfer in the laminar regime was in the center of the zone rather than at the solid-liquid interfaces.

Chang, C. E.↗

Actinide crystal-liquid partitioning for clinopyroxene and Ca3/PO4/2

Coefficients for the partitioning of the actinide elements Th, U and Pu, which are used as indicators of r-process nucleosynthesis and the ages of meteorite and lunar samples, between diopsidic clinopyroxene, whitlockite and silicate liquid at 20 kbar are measured. Fission and alpha track radiography techniques are employed to detect element concentrations in synthetic crystals made using spiked starting materials, under the assumptions of equilibrium partitioning at the crystal-liquid interface and actinide zoning. Analysis of the data indicates results to be consistent with interface equilibrium except at high cooling rates. Th/U/Pu partition coefficients of about 0.002/0.002/O.06 are measured for clinopyroxene and 1.2/0.5/3.4 for whitlockite. The greater incorporation of Pu into the crystalline phases is attributed to the importance of trivalent Pu, and the similarity of its partition coefficient into clinopyroxene to that of the light rare earths supports the concept of Pu/rare earth dating.

Benjamin, T.↗

Ripplon scattering using grating heterodyne spectroscopy

Heterodyne photon spectroscopy was used for the study of the viseo-elastic properties of the liquid interface by studying the scattering from thermal ripplons. A theory of a heterodyne apparatus based on a grating is presented, and the heterodyne condition is given in terms of the parameters of the experimental set-up. Emphasis was placed on the study of the instrumental function and its influence on the measurement data. The instrumental function is not always gaussian, but its functional form depends on the parameters of the experimental set-up. An algorithm is suggested to arrive at the center frequency and half width at half height of the spectrum from the noisy experimental data, and applied to the measurement data obtained from ethanol and water surfaces.

Sirohi, R. S.↗

Measurement of surface flow velocity with ripplon scattering

It was shown that the light scattered from the ripplons on a moving liquid interface can be used to measure the velocity fields in the interface. The technique measures the true interface velocity. It is, however, limited to the measurement of relatively fast moving interfaces because the scattered irradiance is large only in a very small angular range about the specularly reflected beam, and the concerted influence of instrumental and natural braodening of the power spectrum leads to severely overlapping doublet for low velocity fields.

Sirohi, R. S.↗

Fabrication of titanium multiwall Thermal Protection System (TPS) curved panel

A method is described for fabricating curved T1-6Al-4V multiwall panels having a single radius of curvature of 30.5 cm (12 inches). A panel 30.5 x 30.5 x 1.7 cm (12 x 12 x .688 inch) having 4 dimpled sheets, 5 undimpled sheets, and stepped side closures was designed, fabricated and delivered for evaluation. Tool design for skin and dimpled sheet forming are described as well as layup and liquid interface diffusion bonding.

Blair, W.↗

Non-isothermal effects on SO2 absorption by water droplets. I - Model development. II - Results and discussion

An analytic model of SO2 absorption in a falling water droplet is developed and a simulation of SO2 washout is performed. Nonisothermic effects on drop growth, droplet physical parameters, reaction rates, and multicomponent diffusion are treated in the model. The gas-liquid interface is assumed to be at equilibrium, and interfacial resistance is negligible. Raindrops are simulated as falling from a 2 km height through an atmospheric region containing SO2. The droplets decrease in size from evaporation and cooling, and their slightly basic pH aids SO2 absorption. The simulation indicates higher SO2 absorption at higher altitudes, and desorption may occur at ground level. Isothermal effects are concluded to be significant, and quantification of effects will depend on further modelling.

Reda, M.↗

The Effect of Solidification Rate on Morphological Stability

At low solidification rates, the criterion for the onset of morphological instability parallels closely the criterion of constitutional supercooling. At somewhat larger rates of solidification, however, the results of the perturbation theory of morphological instability differ significantly from the predictions of constitutional supercooling. This arises because the critical wave length for instability decreases as solidification rate increases and thus the effects of capillarity (solid-liquid surface tension) play a strong stabilizing role. This gives rise to the concept of absolute stability, according to which the system will always be stable for a sufficiently large rate of solidification. This enhanced stabilization by capillarity is present only so long as local equilibrium is maintained at the solid-liquid interface. If the interfacial temperature drops below its equilibrium value by an amount dependent on growth rate, oscillatory morphological instabilities can occur. The differences among these various stability criteria are illustrated by means of some simple two-dimensional diagrams that should supplant the conventional plots of (temperature gradient)/(growth rate) vs. alloy concentration.

Sekerka, R. F.↗

Low Angle Silicon Sheet Growth: a Review of Progress, Problems and Promise

High growth rates which are the key to a successful low cost silicon ribbon technology is discussed. The heat of fusion is conducted along the grown ribbon for some distance before it can be dissipated. The conduction path is limited to the cross sectional area of the ribbon, since the solid-liquid interface is perpendicular to the pull direction. Horizontal ribbon growth is achieved by providing an extended solidification interface, parallel within a few degrees, to the pull direction. The heat of fusion need only be conducted through the thickness of the ribbon and is dissipated from the upper surface which comprises an area equal to the interface. Growth of up to 15cm wide ribbon and continuous growth of ribbons as long as 120 meters is demonstrated. Areal productivity as high as 2.7 sq/m/hr is shown for a single 15 cm ribbon, while typical values of approximately 1 sq/m/hr are obtained in the growth of 5 cm ribbon.

H. E. Bates↗

Free-surface phenomena under low- and zero-gravity conditions

A free surface experiment using a liquid doped with a fluorescent dye under sheet illumination is summarized. The work includes the selection of a CCD camera for use during the design stages of the experiment as well as a preliminary demonstration of this technique in the production of a contour map of a liquid-liquid interface with better than 0.1 mm resolution. With a different data sampling and storage procedure, the image processing is reduced to a simple thresholding procedure which can be done in hardware.

Hesselink, L.↗

Hot stage and sample cell design for the solidification of transparent materials with and without forced convection

A temperature gradient stage design for optical microscopy is described. Exceptional thermal stability is the major feature. The stage is used to study crystal growth phenomena occurring at the solid-liquid interface. The apparatus is designed to use transparent organic solutions as models for the study of metal-like solidification. The stage provides a controlled thermal environment for unidirectional solidification of low melting temperature materials. Freezing rate is regulated by mechanically sliding in the stage a thin glass cell containing the materials being studied. Two cell assemblies are described. One type is used for convection-free and the other for controlled forced convection studies of the solidification interface.

Kaukler, W. F.↗

Electrochemical etching of the semiconductor lead tin telluride

Convective currents during the Bridgman growth of a compound semiconductor lead to temperature fluctuations at the solid-liquid interface. These temperature fluctuations in turn lead to microscopic compositional variations in the solid. Electrochemical principles have been applied to develop three etches which delineate the variations in the compound semiconductor, lead tin telluride, and allow optical studies of the growth kinetics of this material. Use of these etches has shown periodic lines during the initial growth, with indications of oscillatory instabilities developing in later stages of growth, and, finally, complete breakdown of the interface.

Barber, P. G.↗

The Influence of Low Frequency Mechanical Vibrations on the Growth of Single Crystals

The optimum conditions for crystal growth are usually achieved either by suppressing convective fluid flows (e.g., by the use of a low-gravity environment) or by over-riding thermal and solutal convection by the use of a strong stirring action. A novel stirring technique has been developed which involves subjecting a vertical crucible to a circle in a horizontal plane (without rotation). Use of an amplitude of 3 mm at a frequency of approx 6 Hz produced complete mixing of a non-uniform aqueous liquid in a few seconds. The mixing action involved the downward flow of liquid in the outer annulus of the liquid, driven by surface waves. When the downward flowing liquid reaches the bottom of the crucible, it is reflected in a central, upward flowing spiral. This flow pattern should be beneficial for crystal growth by the Bridgman method since it will sweep impurities away from the walls and produce a more convex solid-liquid interface. Initial attempts to apply the new stirring technique to CdTe crystal growth did not show significant improvement in the number of crystals nucleated, but the interface shape appeared to be close to that predicted.

Feigelson, R. S.↗

Float Zone Experiments in Space

The objective of this work has been to evaluate whether or not Marangoni flow could be suppressed in molten metals by the presence of very thin oxide films. Experimental work has been carried out on molten Sn under UHV conditions. A disk floating zone arrangement was developed to allow in situ Auger examination of molten surfaces. An electron energy loss technique was developed which allows detection of continuous tin oxide films of 6 A or greater. Experiments were planned to detect the effects of oxide formation upon Marangoni flow by measuring: (1) temperature profiles, (2) solid liquid interface shapes, (3) macrosegregation, and (4) the onset of oscillatory Marangoni flow by detecting oscillating temperature variations. Work on (4) showed that oscillatory temperature variations of frequency or = 10 Hz were not present in the disk float zone geometry under conditions of Ma = 4300 with an oxide free molten surface. The disk float zone geometry was modeled with a finite element analysis and temperature and velocity profiles were determined.

Verhoeven, J. D.↗

Modeling Directional Solidification

The objective of the research is to develop tools of use in explaining the results of directional solidification experiments in space. These tools consist of mathematical and experimental models. Experiments are also being flown at low-g to validate the ground-based results. Many metals and semiconductors directionally solidified in space had a diameter less than that of the containing ampoule. In fact this occurred whenever the ampoule contained a gas space. This phenomenon has been attributed in a vague way to lack of wetting of the ampoule wall by the melt. The actual liquid behavior by use of low temperature analogs is being observed aboard the KC-135. In the first flight, water was placed in plastic ampoules (not wet) with ceramic end plugs which were wet by the water to simulate a solid-liquid interface. Unfortunately during storage prior to the flight the water began to wet the ampoule wall. Discrete bubbles formed down the axis of the ampoules. New ampoule materials are being used now, with testing for stability prior to the next flight. A theoretical model has also been developed for this phenomenon.

Wilcox, W. R.↗

Effect of LID (Registered) processing on the microstructure and mechanical properties of Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo titanium foil-gauge materials

A study was undertaken to determine the mechanical properties and microstructures resulting from Liquid Interface Diffusion (LID -Registered) processing of foil-gauge specimens of Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo coated with varying amounts of LID material. In addition, the effects of various elevated temperature exposures on the concentration profiles of the LID alloying elements were investigated, using specimens with a narrow strip of LID material applied to the surface. Room and elevated temperature tensile properties were determined for both coated and uncoated specimens. Optical microscopy was used to examine alloy microstructures, and scanning electron microscopy to examine fracture surface morphologies. The chemical concentration profiles of the strip-coated specimens were determined with an electron microprobe.

Balckburn, Linda B.↗

The effect of anisotropic crystal-melt surface tension on grain boundary groove morphology

The shape of a stationary solid-liquid interface in a temperature gradient near a grain boundary in a pure material is calculated for anisotropic crystal-melt surface tension and equal thermal conductivities of crystal and melt. Results are compared with those for the well-known problem of the two-dimensional equilibrium shape of a crystal. For small anisotropy, the resulting interface shapes have continuously turning tangents but differ in detail from the grain boundary groove shapes that have been calculated for isotropic surface tension. For larger anisotropy, the interface shapes have discontinuities in slope as a result of missing orientations.

Voorhees, P. W.↗