Search NASA⌕ Search

SEARCH · Search NASA

Results for “process influence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Influence of powder metallurgy route on precipitation processes in MgTbNd alloy

Solution treated MgTb3Nd2 alloy (nominal composition in wt.%) (ST) and the alloy prepared by hot extrusion of isostatically pressed powder (PM) were isochronally heat treated and studied by electrical resistivity and hardness measurements and by differential scanning calorimetry. Microstructure development was investigated in transmission electron microscopy. Successive precipitation of transient phases in the sequence β″ (D0{sub 19} plates) → β′(cbco) → β{sub 1} (Mg{sub 3}Gd type, fcc) → β (Mg{sub 5}Gd type, fcc) known from the ST alloy was identified also in the PM alloy. The early precipitation stage (D0{sub 19} clusters) revealed in the ST alloy as well as precipitation of equilibrium β{sub e} phase Mg{sub 41}(Tb,Nd){sub 5} manifest themselves only slightly in the PM alloy. Powder metallurgy route does not change the values of activation energies but shifts the temperature ranges of these processes. Vickers hardness of the as prepared state is higher in the PM alloy and is very resistant against the heat treatment up to 510 °C. Contrary to the ST alloy precipitation due to isochronal annealing does not lead to pronounced hardness changes in the PM alloy. - Highlights: • Powder metallurgy (PM) does not change precipitation sequence in MgTbNd alloy. • Temperature ranges of transient phase precipitations are shifted in PM alloy. • Hardness is resistant against isochronal heat treatment up to 510 °C in the PM alloy. • PM procedure does not change activation energies of precipitation.

36 MATERIALS SCIENCE↗

Structural and Computational Assessment of the Influence of Wet-Chemical Post-Processing of the Al-Substituted Cubic Li 7 La 3 Zr 2 O 12

Li 7 La 3 Zr 2 O 12 (LLZO) and related compounds are considered as promising candidates for future all-solid-state Li-ion battery applications. Still, the processing of those materials into thin membranes with the right stoichiometry and crystal structure is difficult and laborious. The sensitivity of the Li-ion conductive garnets against moisture and the associated Li + /H + cation exchange makes their processing even more difficult. Formulation of suitable polymer/ceramic hybrid solid state electrolytes could be a prosperous way to reach the future large scale production of solid state Li-ion batteries. In fact, solvent mediated and/or slurry based wet-processing of the LLZO, e.g., tape-casting, could result in irreversible Li-ion loss of the pristine material due to Li + /H + cation exchange. The concomitant structural changes and loss in functionality in terms of Li-ion conductivity are the results of the above process. As such, in the present work a systematic study on the chemical stability and structural retention of Al-substituted LLZO in different solvents is reported. It was found that Li + /H + exchange in LLZO occurs upon solvent immersion, and its magnitude is dependent on the availability of –OH functional groups of the solvent molecules. As a result, a larger degree of Li + /H + exchange causes higher increase of the lattice parameter of the LLZO, determined by synchrotron diffraction analyses. The expansion of the cubic unit cell was ascertained, when Li + was replaced by H + in the host lattice, by ab initio computational studies. The application of the most common solvent as dispersion medium, i.e., high purity water, causes the most significant Li + /H + exchange and, therefore, structural change, while acetonitrile was proven to be the best suitable solvent for wet postprocessing of LLZO. Finally, computational calculations suggested that the Li + /H + exchange could result in diminished ionic, i.e., mixed Li + –H + , conductivity due to the insertion of protons with lower mobility than that of Li-ions.

36 MATERIALS SCIENCE↗

Influence of nuclear exchange on nonadiabatic electron processes in H{sup +}+H{sub 2} collisions

H{sup +}+H{sub 2} collisions are studied by means of a semiclassical approach that explicitly accounts for nuclear rearrangement channels in nonadiabatic electron processes. A set of classical trajectories is used to describe the nuclear motion, while the electronic degrees of freedom are treated quantum mechanically in terms of a three-state expansion of the collision wavefunction. We describe electron capture and vibrational excitation, which can also involve nuclear exchange and dissociation, in the E= 2-1000 eV impact energy range. We compare dynamical results obtained with two parametrizations of the potential energy surface of H{sub 3}{sup +} ground electronic state. Total cross sections for E > 10 eV agree with previous results using a vibronic close-coupling expansion, and with experimental data for E < 10 eV. Additionally, some prototypical features of both nuclear and electron dynamics at low E are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Measurement of the -3 keV resonance in the {sup 13}C({alpha},n){sup 16}O reaction and its influence on the synthesis of s-process nuclei

The {sup 13}C({alpha},n){sup 16}O reaction is the neutron source for the main component of the s-process, responsible of the production of most nuclei in the mass range 90 < A < 204. It is active inside the helium-burning shell in asymptotic giant branch stars, at temperatures < 10{sup 8} K, corresponding to an energy interval where the {sup 13}C({alpha},n){sup 16}O is effective of 140 - 230 keV. In this region, the astrophysical S(E)-factor is dominated by the -3 keV sub-threshold resonance due to the 6.356 MeV level in {sup 17}O, giving rise to a steep increase of the S-factor. Notwithstanding that it plays a crucial role in astrophysics, no direct measurements exist. Therefore, we have applied the Trojan Horse Method (THM) to the {sup 13}C({sup 6}Li,n{sup 16}O)d quasi-free reaction to achieve an experimental estimate of such contribution. For the first time, the ANC for the 6.356 MeV level has been deduced through the THM as well as the n-partial width, allowing to attain an unprecedented accuracy in the {sup 13}C({alpha},n){sup 16}O study. Though a larger ANC for the 6.356 MeV level is measured, our experimental S(E) factor agrees with the most recent extrapolation in the literature in the 140 - 230 keV energy interval, the accuracy being greatly enhanced thanks to this innovative approach.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Thermal conductivity of GaN single crystals: Influence of impurities incorporated in different growth processes

The thermal conductivity of GaN crystals grown by different techniques is analyzed using the 3ω method in the temperature range of 30 K to 295 K. GaN wafers grown by the ammonothermal method show a significant variation in thermal conductivity at room temperature with values ranging between 164 W m -1 K -1 and 196 W m -1 K -1 . GaN crystals produced with the sodium flux and hydride vapor phase epitaxy methods show results of 211 W m -1 K -1 and 224 W m -1 K -1 , respectively, at room temperature. Analysis using secondary ion mass spectrometry indicates varying amounts of impurities between the respective crystals and explains the behavior of thermal conductivity trends in the samples. The observed difference between thermal conductivity curves suggests that scattering of phonons at point defects dominates the thermal conductivity of GaN within the investigated temperature range. Finally, deviations of model curves from thermal conductivity measurements and disparities between modelled characteristic lengths and actual sample thicknesses indicate that phonon resonances are active in GaN.

36 MATERIALS SCIENCE↗

Urban Landscape and Climate Change

A workshop on how earth system models incorporate the influences of urban environments on climate, with an emphasis on how large observation studies can be used to aid the modeling community, was held on August 27 - 28, 2013 at Argonne National Laboratory. The goal of the workshop was to identify urban processes important in influencing the predictive capability of regional climate models and global earth system models, the impacts of climate change that are important for future urban centers, data available or needed to develop a representative model of urban ecosystems, and how cities can use that information to improve the lives of their residents.

54 ENVIRONMENTAL SCIENCES↗

The influence of acceleration forces on nucleation, solidification, and deformation processes in tin single crystals

An apparatus was designed and assembled to directionally solidify single crystals under the influence of acceleration forces of various magnitudes. The investigation conducted showed that acceleration gradients produce a preferred growth orientation effect not previously observed for tin. Convection currents at approximately 5-g encourage multiple nucleation and subsequent random orientation of growth direction. Deformation effects such as recrystallization and twinning are observed at acceleration levels greater than 2-g.

Johnston, M. H.↗

The possible influence of upstream upper-level baroclinic processes on the development of the QE II storm

An analysis of the QE II storm of September 9-11, 1978 presents evidence for the existence of upper-level baroclinic processes upstream of the rapidly developing cyclone. The analysis shows that a deepening shortwave trough was located 400 to 500 km upstream of the site of the storm 12 h prior to rapid cyclogenesis. The trough was associated with: (1) a polar jet marked by 65 m/s winds in its core and significant vertical and horizontal wind shear, (2) positive vorticity advection and divergence at the 300 mb level, and (3) an intense frontal zone that extended from 300 mb down to the surface. It also appears that a tropopause fold likely extruded stratospheric air down to the 700-800 mb level, 400-500 km upstream of the surface low and 12 h prior to the explosive development phase of the cyclone. These findings raise questions about Gyakum's (1983) assertion that the QE II storm developed in an area in which the baroclinic support was confined to the lower troposphere and the related assertion by Anthes et al. (1983) that upper-level forcing upstream of the area of rapid cyclogenesis was weak and apparently not important in this case.

Uccellini, L. W.↗

Influence of residual gravity on crystal growth processes

The effects of steady and time-dependent residual accelerations on representative melt and solution crystal growth systems have been investigated using numerical models. For the melt growth system, it was found that the lateral nonuniformity in crystal composition, depending on the particular operating conditions, can be very sensitive to the orientation of the steady component of the residual gravity vector down to 10 to the -6th g. Oscillatory residual accelerations (g-jitter) were found to lead to transients in the dopant distribution. For the solution growth, longtime simulations showed that at 10 to the -5th g, and the cooling rates used in Spacelab 3 experiments, diffusive transport dominates only in the beginning. Convective transport becomes increasingly significant after 3 to 5 hours, depending on the orientation of the crystal in the residual gravity field.

Rosenberger, F.↗

Influence of aerodynamic roughness length on aeolian processes: Earth, Mars, Venus

The aerodynamic roughness length (z sub 0) is the height at which a wind profile assumes a zero velocity. The lower part of the atmospheric boundary layer will be impeded by friction with the surface. An increase in surface roughness will also increase the shear stress required to initiate particle entrainment by the wind. Bagnold (1941) estimated z sub 0 as being 1/30 of the mean particle size. In Nature, surface roughness is composed of nonerodible elements as well as sand-size erodible particles. To assess z sub 0 values as a function of terrain, field experiments were conducted to obtain wind profiles monitored over natural surfaces at 15 sites in the Mojave Desert, Death Valley, and Nye County, Nevada. These sites span a variety of arid-land terrains, including smooth playas, alluvial fans, and lava flows; z sub 0 values ranged from 0.0001 cm to 1 cm. These values were incorporated in a threshold model and a flux model to assess transport efficiency over such terrains in three planetary environments (Venus, Earth, and Mars), and for particle sizes ranging from 60-500 micron. Threshold and flux are a function of planetary environment, particle density and size (Dp), and z sub 0, and the shear velocity of 1.2 x U sub *t (for Dp = 250 micron and z sub 0 = 0.84). Results show that flux on Mars is approximately 14 g/(cm x s), on Earth it is approximately 3 g/(cm x s), and on Venus 0.5 g/(cm x s). Under all planetary environments, the results also show a dramatic decrease in the flux for particles greater than 200 microns when z sub 0 increases above 0.0085 cm (corresponding to sites consisting of alluvium). When z sub 0 approaches 0.03 cm (corresponding to a mantled pahoehoe lava), the flux diminishes.

Blumberg, Dan G.↗

Aspects of Assessment of Packages with Wood Filled Impact Limiters during Fire Tests - 17191

Packages for the transport of radioactive material are often equipped with impact limiters consisting of wood, encapsulated by steel sheets. These impact limiters shall ensure that the transport casks meet the mechanical and thermal IAEA regulatory test requirements. According to the accident conditions of transport it is mandatory to expose the specimens to a cumulative effect by mechanical and thermal impacts. The mechanical tests consist of a free drop from 9 m onto a flat unyielding target and a 1 m drop onto a puncture bar. After damage caused by mechanical test sequences the package has to withstand a severe fire scenario. Corresponding to the IAEA advisory material it is required that the impact attitudes for the 9 m drop test and for the puncture test have to be such as to produce maximum damage, taking into account the thermal test. Moreover, any damage, which would give rise to increased radiation or loss of containment or affect the confinement system after the thermal test, should be considered. During and following the thermal test, the specimen shall not be artificially cooled and any combustion of materials of the package shall be permitted to proceed naturally. Different works from the French Institute for Radiological Protection and Nuclear Safety (IRSN) and BAM show that additional energy supply from a pre-damaged impact limiter to the cask could occur. This effect should be considered within the safety assessment of the containment. Thermal effects at the closure system of the cask, which might result in an elevated activity release, have to be excluded. BAM conducted small scale tests with wood filled metal buckets showing continuing combustion processes during the cooling down phase. These test results are presented. As not much is known about smouldering processes in wood filled impact limiters, it is highly complex to define pre-damage of impact limiters, which are conservative, regarding the maximum damaging energy flow from the impact limiter to the containment system. More research has to be done to develop models to examine the effects of smouldering impact limiters on the containment of packages for the transport of radioactive material. Aspects of assessment and its difficulties are shown. BAM as a competent authority for the approval of transport casks for radioactive material in Germany operates the test facilities to examine the issue of mechanical damage, combustion and heat transfer for such kind of package systems. For this purpose, the knowledge from real drop tests with casks of a mass partly over 100 tons was transferred to a test application. A thermal test will take place with a wood filled test specimen with a diameter of about 2.3 meters. The aim is to understand the phenomena of smouldering under the consideration of relevant regulatory boundary conditions. The process of smouldering is described with regard to the requirements in the thermal assessment of safety of packages for the transport of radioactive material. Requirements concerning the pre-damage of packages for the maximum damage of impact limiters are discussed. Parameters influencing the smouldering process are identified. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Considerations of the Differences between Bedded and Domal Salt Pertaining to Disposal of Heat-Generating Nuclear Waste

Salt formations hold promise for eternal removal of nuclear waste from our biosphere. Germany and the United States have ample salt formations for this purpose, ranging from flat-bedded formations to geologically mature dome structures. As both nations revisit nuclear waste disposal options, the choice between bedded, domal, or intermediate pillow formations is once again a contemporary issue. For decades, favorable attributes of salt as a disposal medium have been extoled and evaluated, carefully and thoroughly. Yet, a sense of discovery continues as science and engineering interrogate naturally heterogeneous systems. Salt formations are impermeable to fluids. Excavation-induced fractures heal as seal systems are placed or natural closure progresses toward equilibrium. Engineering required for nuclear waste disposal gains from mining and storage industries, as humans have been mining salt for millennia. This great intellectual warehouse has been honed and distilled, but not perfected, for all nuances of nuclear waste disposal. Nonetheless, nations are able and have already produced suitable license applications for radioactive waste disposal in salt. A remaining conundrum is site location. Salt formations provide isolation and geotechnical barriers reestablish impermeability after waste is placed in the geology. Between excavation and closure, physical, mechanical, thermal, chemical, and hydrological processes ensue. Positive attributes for isolation in salt have many commonalities independent of the geologic setting. In some cases, specific details of the environment will affect the disposal concept and thereby define interaction of features, events and processes, while simultaneously influencing scenario development. Here we identify and discuss high-level differences and similarities of bedded and domal salt formations. Positive geologic and engineering attributes for disposal purposes are more common among salt formations than are significant differences. Developing models, testing material, characterizing processes, and analyzing performance all have overlapping application regardless of the salt formation of interest.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Considerations of the Differences between Bedded and Domal Salt Pertaining to Disposal of Heat-Generating Nuclear Waste

Salt formations hold promise for eternal removal of nuclear waste from our biosphere. Germany and the United States have ample salt formations for this purpose, ranging from flat-bedded formations to geologically mature dome structures. As both nations revisit nuclear waste disposal options, the choice between bedded, domal, or intermediate pillow formations is once again a contemporary issue. For decades, favorable attributes of salt as a disposal medium have been extoled and evaluated, carefully and thoroughly. Yet, a sense of discovery continues as science and engineering interrogate naturally heterogeneous systems. Salt formations are impermeable to fluids. Excavation-induced fractures heal as seal systems are placed or natural closure progresses toward equilibrium. Engineering required for nuclear waste disposal gains from mining and storage industries, as humans have been mining salt for millennia. This great intellectual warehouse has been honed and distilled, but not perfected, for all nuances of nuclear waste disposal. Nonetheless, nations are able and have already produced suitable license applications for radioactive waste disposal in salt. A remaining conundrum is site location. Salt formations provide isolation, and geotechnical barriers reestablish impermeability after waste is placed in the geology. Between excavation and closure, physical, mechanical, thermal, chemical, and hydrological processes ensue. Positive attributes for isolation in salt have many commonalities independent of the geologic setting. In some cases, specific details of the environment will affect the disposal concept and thereby define interaction of features, events and processes, while simultaneously influencing scenario development. Here we identify and discuss high-level differences and similarities of bedded and domal salt formations. Positive geologic and engineering attributes for disposal purposes are more common among salt formations than are significant differences. Developing models, testing material, characterizing processes, and analyzing performance all have overlapping application regardless of the salt formation of interest.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

An Analysis of Errors in a Reuse-Oriented Development Environment

Component reuse is widely considered vital for obtaining significant improvement in development productivity. However, as an organization adopts a reuse-oriented development process, the nature of the problems in development is likely to change. In this paper, we use a measurement-based approach to better understand and evaluate an evolving reuse process. More specifically, we study the effects of reuse across seven projects in narrow domain from a single development organization. An analysis of the errors that occur in new and reused components across all phases of system development provides insight into the factors influencing the reuse process. We found significant differences between errors associated with new and various types of reused components in terms of the types of errors committed, when errors are introduced, and the effect that the errors have on the development process.

Thomas, William M.↗

Structural phase transitions of (Bi 1$-$x Sb x ) 2 (Te 1$-$y Se y ) 3 compounds under high pressure and the influence of the atomic radius on the compression processes of tetradymites

Recently, A 2 B 3 -type tetradymites have developed into a hot topic in physical and material research fields, where the A and B atoms represent V and VI group elements, respectively. In this study, in situ angle-dispersive X-ray diffraction measurements were performed on Bi 2 Te 2 Se, BiSbTeSe 2 , and Sb 2 Te 2 Se tetradymites under high pressure. Bi 2 Te 2 Se transforms from a layered rhombohedral structure (phase I) into 7-fold monoclinic (phase II) and body-centered tetragonal (phase IV) structures at about 8.0 and 14.3 GPa, respectively, without an 8-fold monoclinic structure (phase III) similar to that in Bi 2 Te 3 . Thus, the compression behavior of Bi 2 Te 2 Se is the same as that of Bi 2 Se 3 , which could also be obtained from first-principles calculations and in situ high-pressure electrical resistance measurements. Under high pressure, BiSbTeSe 2 and Sb 2 Te 2 Se undergo similar structural phase transitions to Bi 2 Te 2 Se, which indicates that the compression process of tellurides can be modulated by doping Se in Te sites. According to these high-pressure investigations of A 2 B 3 -type tetradymites, the decrease of the B-site atomic radius shrinks the stable pressure range of phase III and expands that of phase II, whereas the decrease of the A-site atomic radius induces a different effect, i.e. expanding the stable pressure range of phase III and shrinking that of phase II. Lastly, the influence of the atomic radius on the compression process of tetradymites is closely related to the chemical composition and the atom arrangement in the quintuple layer.

36 MATERIALS SCIENCE↗

Modeling and Analysis of The Pressure Die Casting Using Response Surface Methodology

Pressure die casting is successfully used in the manufacture of Aluminum alloys components for automobile and many other industries. Die casting is a process involving many process parameters having complex relationship with the quality of the cast product. Though various process parameters have influence on the quality of die cast component, major influence is seen by the die casting machine parameters and their proper settings. In the present work, non-linear regression models have been developed for making predictions and analyzing the effect of die casting machine parameters on the performance characteristics of die casting process. Design of Experiments (DOE) with Response Surface Methodology (RSM) has been used to analyze the effect of effect of input parameters and their interaction on the response and further used to develop nonlinear input-output relationships. Die casting machine parameters, namely, fast shot velocity, slow shot to fast shot change over point, intensification pressure and holding time have been considered as the input variables. The quality characteristics of the cast product were determined by porosity, hardness and surface rough roughness (output/responses). Design of experiments has been used to plan the experiments and analyze the impact of variables on the quality of casting. On the other-hand Response Surface Methodology (Central Composite Design) is utilized to develop non-linear input-output relationships (regression models). The developed regression models have been tested for their statistical adequacy through ANOVA test. The practical usefulness of these models has been tested with some test cases. These models can be used to make the predictions about different quality characteristics, for the known set of die casting machine parameters, without conducting the experiments.

36 MATERIALS SCIENCE↗