Search NASA⌕ Search

SEARCH · Search NASA

Results for “solution design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

An inverse method for subcritical flows

An exact method is presented for two-dimensional subsonic flow within the limitations of the tangent gas approximation. While Woods (1961) studied these equations and proposed iterative methods for the solution of both the iterative and inverse problems, the inverse method here presented is noniterative and exact. It is shown that the direct Euler solution over the designed airfoil is very close to the input speed distribution, and that the constraints necessitated by upstream condition and closure requirements are easily incorporated.

Daripa, P. K.↗

Phased array antenna for space shuttle orbiter

The National Aeronautics and Space Administration is developing a distributed phased array antenna at the Lyndon B. Johnson Space Center as a possible upgrade for the Space Shuttle Orbiter S-band phase modulation communications system. The antenna consists of an eight-element transmit section, eight-element receive section, and a single L-band receive element. The antenna design is constrained by the existing Orbiter system and space environment. The solution to the interface design problems led to an antenna system which provides improved link margins and yet supports previous operational configurations. This paper describes the system development, antenna hardware, and the interface consideration which led to the final design.

Davidson, Shayla E.↗

Assessment, development and application of combustor aerothermal models

The gas turbine combustion system design and development effort is an engineering exercise to obtain an acceptable solution to the conflicting design trade-offs between: combustion efficiency, gaseous emissions, smoke, ignition, restart, lean blowout, burner exit temperature quality, structural durability, and life cycle cost. For many years, these combustor design trade-offs have been carried out with the help of fundamental reasoning and extensive component and bench testing, backed by empirical and experience correlations. Recent advances in the capability of computational fluid dynamics (CFD) codes have led to their application to complex three-dimensional flows such as those in the gas turbine combustor. A number of US. Government and industry sponsored programs have made significant contributions to the formulation, development, and verification of an analytical combustor design methodology which will better define the aerothermal loads in a combustor, and be a valuable tool for design of future combustion systems. The contributions made by NASA Hot Section Technology (HOST) sponsored Aerothermal Modeling and supporting programs are described in this paper.

Aerothermal modeling↗

Assessment, development, and application of combustor aerothermal models

The gas turbine combustion system design and development effort is an engineering exercise to obtain an acceptable solution to the conflicting design trade-offs between combustion efficiency, gaseous emissions, smoke, ignition, restart, lean blowout, burner exit temperature quality, structural durability, and life cycle cost. For many years, these combustor design trade-offs have been carried out with the help of fundamental reasoning and extensive component and bench testing, backed by empirical and experience correlations. Recent advances in the capability of computational fluid dynamcis codes have led to their application to complex 3-D flows such as those in the gas turbine combustor. A number of U.S. Government and industry sponsored programs have made significant contributions to the formulation, development, and verification of an analytical combustor design methodology which will better define the aerothermal loads in a combustor, and be a valuable tool for design of future combustion systems. The contributions made by NASA Hot Section Technology (HOST) sponsored Aerothermal Modeling and supporting programs are described.

Holdeman, J. D.↗

Computing Optimal Multiarc Trajectories

Optimal Multi-Arc Trajectories (OMAT) computer program designed to calculate solution to optimal-trajectory problem in cases of low thrust-to-weight ratios. Developed for two-body exoatmospheric problem with three degrees of freedom in inverse-square force field. Offers two different options: impulsive changes in velocity and finite burns with low thrust-to-weight ratios. Two distinct solutions available from program: optimal multi-impulse (OMI) solution and optimal multiburn (OMB) solution. Two solutions obtained separately, or results of OMI solution used to guess unknown parameters of OMB solution. Written for DEC VAX-series computer. Written completely in FORTRAN 77.

Jezewski, Donald J.↗

Assessment, development, and application of combustor aerothermal models

The gas turbine combustion system design and development effort is an engineering exercise to obtain an acceptable solution to the conflicting design trade-offs between: combustion efficiency, gaseous emissions, smoke, ignition, restart, lean blowout, burner exit temperature quality, structural durability, and life cycle cost. For many years, these combustor design trade-offs have been carried out with the help of fundamental reasoning and extensive component and bench testing, backed by empirical and experience correlations. Recent advances in the capability of computational fluid dynamics (CFD) codes have led to their application to complex three-dimensional flows such as those in the gas turbine combustor. A number of U.S. Govern- ment and industry sponsored programs have made significant contributions to the formulation, development, and verification of an analytical combustor design methodology which will better define the aerothermal loads in a combustor, and be a valuable tool for design of future combustion systems. The contributions made by NASA Hot Section Technology (HOST) sponsored Aero- thermal Modeling and supporting programs are described in this paper

J D Holdeman↗

Design and Navier-Stokes analysis of hypersonic wind tunnel nozzles

Four hypersonic wind tunnel nozzles ranging in Mach number from 6 to 17 are designed with the method of characteristics and boundary layer approach (MOC/BL) and analyzed with a Navier-Stokes solver. Limitations of the MOC/BL approach when applied to thick high speed boundary layers with non-zero normal pressure gradients are investigated. Working gases include ideal air, thermally perfect nitrogen and virial CF4. Agreement between the design conditions and Navier-Stokes solutions for ideal air at Mach 6 is good. Thermally perfect nitrogen showed poor agreement at Mach 13.5 and Mach 17. Navier-Stokes solutions for CF4 are not obtained, but comparison of the effects of low gamma to those of high Mach number suggests that the Navier-Stokes solution would not compare well with design.

Benton, James R.↗

A unified Navier-Stokes flowfield and performance analysis of liquid rocket engines

To improve the current composite solutions in the design and analysis of liquid propulsive engines, a computational fluid dynamics model capable of calculating the nonreacting and reacting flows from the combustion chamber, through the nozzle to the external plume, was developed. The Space Shuttle Main Engine (SSME) fired at sea level, along with the flowfields of several other nozzles were investigated. The bell-shaped SSME nozzle was run at 100 percent power level at various flow conditions, the computed flow results and performance compared well with those of other standard codes and engine hot fire test data.

Wang, Ten-See↗

An unmanned probe to Pluto

Now that Voyager II has completed its grand tour of the solar system, all the planets in the solar system, with the exception of Pluto, have been studied. Even now, missions to return to Mercury, Venus, Mars Jupiter, and Saturn are currently flying or are planned. However, a mission to explore Pluto is not, at the present time, being considered seriously. The design problem presented to the students was very general, i.e., design an unmanned mission to Pluto with a launch window constraint of the years 2000 to 2010. All other characteristics of the mission, such as mission type (flyby, orbiter, lander, penetrator), scientific objectives and payload, and the propulsion system were to be determined by the design teams. The design studies exposed several general problems to be solved. Due to the extreme distance to Pluto (and a corresponding travel time in the range of 10 to 25 years), the spacecraft had to be lighter and more robust than current spacecraft designs. In addition, advanced propulsion concepts had to be considered. These included the new generation of launch vehicles and upper stages and nuclear electric propulsion. The probe design offered an abundance of synthesis and analysis problems. These included sizing trade studies, selection of subsystem components, analysis of spacecraft dynamics, stability and control, structural design and material selection, trajectory design, and selection of scientific equipment. Since the characteristics of the mission, excluding the launch window, were to be determined by the design teams, the solutions varied widely.

Source record↗

Combined structures-controls optimization of lattice trusses

The role that distributed parameter model can play in CSI is demonstrated, in particular in combined structures controls optimization problems of importance in preliminary design. Closed form solutions can be obtained for performance criteria such as rms attitude error, making possible analytical solutions of the optimization problem. This is in contrast to the need for numerical computer solution involving the inversion of large matrices in traditional finite element model (FEM) use. Another advantage of the analytic solution is that it can provide much needed insight into phenomena that can otherwise be obscured or difficult to discern from numerical computer results. As a compromise in level of complexity between a toy lab model and a real space structure, the lattice truss used in the EPS (Earth Pointing Satellite) was chosen. The optimization problem chosen is a generic one: of minimizing the structure mass subject to a specified stability margin and to a specified upper bond on the rms attitude error, using a co-located controller and sensors. Standard FEM treating each bar as a truss element is used, while the continuum model is anisotropic Timoshenko beam model. Performance criteria are derived for each model, except that for the distributed parameter model, explicit closed form solutions was obtained. Numerical results obtained by the two model show complete agreement.

Balakrishnan, A. V.↗

Prediction of the Thrust Performance and the Flowfield of Liquid Rocket Engines

In an effort to improve the current solutions in the design and analysis of liquid propulsive engines, a computational fluid dynamics (CFD) model capable of calculating the reacting flows from the combustion chamber, through the nozzle to the external plume, was developed. The Space Shuttle Main Engine (SSME) fired at sea level, was investigated as a sample case. The CFD model, FDNS, is a pressure based, non-staggered grid, viscous/inviscid, ideal gas/real gas, reactive code. An adaptive upwinding differencing scheme is employed for the spatial discretization. The upwind scheme is based on fourth order central differencing with fourth order damping for smooth regions, and second order central differencing with second order damping for shock capturing. It is equipped with a CHMQGM equilibrium chemistry algorithm and a PARASOL finite rate chemistry algorithm using the point implicit method. The computed flow results and performance compared well with those of other standard codes and engine hot fire test data. In addition, the transient nozzle flowfield calculation was also performed to demonstrate the ability of FDNS in capturing the flow separation during the startup process.

Wang, T.-S.↗

Synthetic-Aperture Antenna Array With Beam-Waveguide Coupling

Proposed synthetic-aperture antenna array for radio astronomy at wavelengths between 60 and 300 micrometers includes twelve 3.5-m-diameter paraboloidal-dish antennas at various positions along three 0.5-km-long arms of Y-shaped pattern. Receivers located centrally, with consequent reductions in complexity and cost. Innovative features of design also stimulates solutions to engineering problems arising in terrestrial radio systems.

Mahoney, Michael J.↗

A study of flying-boat take-off

It is shown that the normal resistance curve for a flying boat may be approximated by two straight lines. The equations for take-off distance and time, derived from this approximation, are applied to a series of flying boats and the resulting factors are plotted in non dimensional form in a series of charts. Take-off performances from the charts are shown to be in good agreement with step-by-step integrations. Some applications of the charts to the solution of general design problems are included.

Diehl, Walter S↗

Numerical Algorithms Based on Biorthogonal Wavelets

Wavelet bases are used to generate spaces of approximation for the resolution of bidimensional elliptic and parabolic problems. Under some specific hypotheses relating the properties of the wavelets to the order of the involved operators, it is shown that an approximate solution can be built. This approximation is then stable and converges towards the exact solution. It is designed such that fast algorithms involving biorthogonal multi resolution analyses can be used to resolve the corresponding numerical problems. Detailed algorithms are provided as well as the results of numerical tests on partial differential equations defined on the bidimensional torus.

Ponenti, Pj.↗

TPS Sizing for Access-to-Space Vehicles

A study was carried out to identify, develop, and benchmark simulation techniques needed for optimum thermal protection system (TPS) material selection and sizing for reusable launch vehicles. Fully viscous, chemically reacting, Navier-Stokes flow solutions over the Langley wing-body single stage to orbit (SSTO) configuration were generated and coupled with an in-depth conduction code. Results from the study provide detailed TPS heat shield materials selection and thickness sizing for the wing-body SSTO. These results are the first ever achieved through the use of a complete, trajectory based hypersonic, Navier-Stokes solution database. TPS designs were obtained for both laminar and turbulent entry trajectories using the Access-to-Space baseline materials such as tailorable advanced blanket insulation. The TPS design effects (materials selection and thickness) of coupling material characteristics to the aerothermal environment are illustrated. Finally, a sample validation case using the shuttle flight database is included.

Henline, William↗

Numerical Algorithms Based on Biorthogonal Wavelets

Wavelet bases are used to generate spaces of approximation for the resolution of bidimensional elliptic and parabolic problems. Under some specific hypotheses relating the properties of the wavelets to the order of the involved operators, it is shown that an approximate solution can be built. This approximation is then stable and converges towards the exact solution. It is designed such that fast algorithms involving biorthogonal multi resolution analyses can be used to resolve the corresponding numerical problems. Detailed algorithms are provided as well as the results of numerical tests on partial differential equations defined on the bidimensional torus.

Ponenti, Pj.↗

Development of a Probabilistic Dynamic Synthesis Method for the Analysis of Nondeterministic Structures

Accounting for the statistical geometric and material variability of structures in analysis has been a topic of considerable research for the last 30 years. The determination of quantifiable measures of statistical probability of a desired response variable, such as natural frequency, maximum displacement, or stress, to replace experience-based "safety factors" has been a primary goal of these studies. There are, however, several problems associated with their satisfactory application to realistic structures, such as bladed disks in turbomachinery. These include the accurate definition of the input random variables (rv's), the large size of the finite element models frequently used to simulate these structures, which makes even a single deterministic analysis expensive, and accurate generation of the cumulative distribution function (CDF) necessary to obtain the probability of the desired response variables. The research presented here applies a methodology called probabilistic dynamic synthesis (PDS) to solve these problems. The PDS method uses dynamic characteristics of substructures measured from modal test as the input rv's, rather than "primitive" rv's such as material or geometric uncertainties. These dynamic characteristics, which are the free-free eigenvalues, eigenvectors, and residual flexibility (RF), are readily measured and for many substructures, a reasonable sample set of these measurements can be obtained. The statistics for these rv's accurately account for the entire random character of the substructure. Using the RF method of component mode synthesis, these dynamic characteristics are used to generate reduced-size sample models of the substructures, which are then coupled to form system models. These sample models are used to obtain the CDF of the response variable by either applying Monte Carlo simulation or by generating data points for use in the response surface reliability method, which can perform the probabilistic analysis with an order of magnitude less computational effort. Both free- and forced-response analyses have been performed, and the results indicate that, while there is considerable room for improvement, the method produces usable and more representative solutions for the design of realistic structures with a substantial savings in computer time.

Brown, A. M.↗

High Speed Rotor Head Mounted Instrumentation System

NASA Ames Research Center has been investigating the air flow of a rotor blade on a UH-60 Blackhawk helicopter in-flight. This paper will address the hardware problems and solutions used to design and fabricate an instrumentation system on top of a UH-60 main rotor head. The instrumentation system consisted of 10 data systems operating in parallel and collected data from 370 sensors that are mounted in four rotor blades and on the rotating rotor head. The data was recorded on board the aircraft and simultaneously down linked to the ground station at 7.5 MHz.

Hee, Leonard↗