Search NASA⌕ Search

SEARCH · Search NASA

Results for “source location”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Anisotropic neutron response of trans-stilbene and impact on a handheld dual particle imager

Here this manuscript details measurements of the anisotropic light-output response of trans-stilbene, henceforth referred to as stilbene, along the three primary crystal planes and analyzes how this anisotropic response impacts neutron image reconstruction in a handheld dual particle imager (H2DPI). A prototype H2DPI composed of stilbene pillars (6 x 6 x 50 mm 3 ) coupled to silicon photomultipliers was built and is capable of imaging both fast neutrons and gamma rays from kilogram quantities of special nuclear material. Stilbene was chosen as the scintillating medium for the imager because of its pulse shape discrimination capability, time resolution and relatively high light output. A drawback to using stilbene, however, is the anisotropic response. A recoiling proton from a neutron elastic-scattering event in stilbene will yield different amounts of scintillation light depending on the direction of the recoiling proton with respect to the crystal lattice. This manuscript analyzes how this anisotropic response impacts neutron image reconstruction in 4π. The light output in the three primary crystal planes of stilbene were independently measured 6–7 times for proton recoil energies ranging from 0.5–5.0 MeV using a quasi-monoenergetic time-of-flight neutron source. The measured light-output data in the three crystal planes were fit with a semi-empirical function based on Birks’ formula. These fits were used to reconstruct the location of a 252 Cf source in front of the imager (0°, -0.8°), to the left of the imager (-90°, -0.8°) and directly above the imager (0°, 90°) to determine if it is necessary to apply the directionally-dependent response of stilbene to accurately reconstruct source locations. A bootstrapping technique was applied to the measured data sets to produce 1000 images composed of 2000 cone projections for each source location and each measured light-output curve. List-mode maximum likelihood expectation maximization was applied to each image; the highest pixel location and the full width at half maximum (FWHM) were then recorded. The average and standard deviations of these parameters were taken for each set of images. The maximum difference in the average azimuthal pixel location when varying between the appropriate and incorrect light-output curves for the source locations at (0°, -0.8°) and (-90°, -0.8°) were respectively found to be 1.85 ± 1.39° and 2.03 ± 1.78°. All other pixel locations and FWHMs were within a single standard deviation of uncertainty. Taken together, the anisotropic response of stilbene has negligible impact on the neutron image reconstruction capability of the H2DPI.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Gravitational wave hotspots: Ranking potential locations of single-source gravitational wave emission

The steadily improving sensitivity of pulsar timing arrays (PTAs) suggests that gravitational waves (GWs) from supermassive black hole binary (SMBHB) systems in the nearby universe will be detectable sometime during the next decade. Currently, PTAs assume an equal probability of detection from every sky position, but as evidence grows for a non-isotropic distribution of sources, is there a most likely sky position for a detectable single source of GWs? In this paper, a collection of Galactic catalogs is used to calculate various metrics related to the detectability of a single GW source resolvable above a GW background, assuming that every galaxy has the same probability of containing an SMBHB. Our analyses of these data reveal small probabilities that one of these sources is currently in the PTA band, but as sensitivity is improved regions of consistent probability density are found in predictable locations, specifically around local galaxy clusters.

79 ASTRONOMY AND ASTROPHYSICS↗

Telemetry

The purpose of a telemetry system is to reliably and transparently convey measurement information from a remotely located data generating source to users located in space or on Earth. Typically, data generators are scientific sensors, science housekeeping sensors, engineering sensors and other subsystems on-board a spacecraft.

telemetry system measurement information data gene↗

Data Fusion for a Vision-Radiological System for Source Tracking and Discovery

A multidisciplinary approach to allow the tracking of the movement of radioactive sources by fusing data from multiple radiological and visual sensors is under development. The goal is to improve the ability to detect, locate, track and identify nuclear/radiological threats. The key concept is that such widely available visual and depth sensors can impact radiological detection, since the intensity fall-off in the count rate can be correlated to movement in three dimensions. To enable this, we pose an important question; what is the right combination of sensing modalities and vision algorithms that can best compliment a radiological sensor, for the purpose of detection and tracking of radioactive material? Similarly what is the best radiation detection methods and unfolding algorithms suited for data fusion with tracking data? Data fusion of multi-sensor data for radiation detection have seen some interesting developments lately. Significant examples include intelligent radiation sensor systems (IRSS), which are based on larger numbers of distributed similar or identical radiation sensors coupled with position data for network capable to detect and locate radiation source. Other developments are gamma-ray imaging systems based on Compton scatter in segmented detector arrays. Similar developments using coded apertures or scatter cameras for neutrons have recently occurred. The main limitation of such systems is not so much in their capability but rather in their complexity and cost which is prohibitive for large scale deployment. Presented here is a fusion system based on simple, low-cost computer vision and radiological sensors for tracking of multiple objects and identifying potential radiological materials being transported or shipped. The main focus of this work is the development on two separate calibration algorithms for characterizing the fused sensor system. The deviation from a simple inverse square-root fall-off of radiation intensity is explored and accounted for. In particular, the computer vision system enables a map of distance-dependence of the sources being tracked. Infrared, laser or stereoscopic vision sensors are all options for computer-vision implementation depending on interior vs exterior deployment, resolution desired and other factors. Similarly the radiation sensors will be focused on gamma-ray or neutron detection due to the long travel length and ability to penetrate even moderate shielding. There is a significant difference between the vision sensors and radiation sensors in the way the 'source' or signals are generated. A vision sensor needs an external light-source to illuminate the object and then detects the re-emitted illumination (or lack thereof). However, for a radiation detector, the radioactive material is the source itself. The only exception to this is the field of active interrogations where radiation is beamed into a material to entice new/additional radiation emission beyond what the material would emit spontaneously. The aspect of the nuclear material being the source itself means that all other objects in the environment are 'illuminated' or irradiated by the source. Most radiation will readily penetrate regular material, scatter in new directions or be absorbed. Thus if a radiation source is located near a larger object that object will in turn scatter some radiation that was initially emitted in a direction other than the direction of the radiation detector, this can add to the count rate that is observed. The effect of these scatter is a deviation from the traditional distance dependence of the radiation signal and is a key challenge that needs a combined system calibration solution and algorithms. Thus both an algebraic approach as well as a statistical approach have been developed and independently evaluated to investigate the sensitivity to this deviation from the simplified radiation fall-off as a function of distance. The resulting calibrated system algorithms are used and demonstrated in various laboratory scenarios, and later in realistic tracking scenarios. The selection and testing of radiological and computer-vision sensors for the additional specific scenarios will be the subject of ongoing and future work. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

On mechanical waves and Doppler shifts from moving boundaries

We investigate the propagation of infinitesimal harmonic mechanical waves emitted from a boundary with variable velocity and arriving at a stationary observer. In the classical Doppler effect, X s (t)=vt is the location of the source with constant velocity v. In the present work, however, we consider a source co-located with a moving boundary x=X s (t), where X s (t) can have an arbitrary functional form. For ‘slowly moving’ boundaries (i.e., ones for which the timescale set by the mechanical motion is large in comparison to the inverse of the frequency of the emitted wave), we present a multiple-scale asymptotic analysis of the moving boundary problem for the linear wave equation. Here, we obtain a closed-form leading-order (with respect to the latter small parameter) solution and show that the variable velocity of the boundary results not only in frequency modulation but also in amplitude modulation of the received signal. Consequently, our results extend the applicability of two basic tenets of the theory of a moving source on a stationary domain, specifically that (i) $.\atop{x}_s$ for non-uniform boundary motion can be inserted in place of the constant velocity v in the classical Doppler formula and (ii) that the non-uniform boundary motion introduces variability in the amplitude of the wave. The specific examples of decelerating and oscillatory boundary motion are worked out and illustrated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Extended Gamma-Ray Emission from the G25.0+0.0 Region: A Star-forming Region Powered by the Newly Found OB Association?

We report a study of extended γ -ray emission with the Large Area Telescope (LAT) on board the Fermi Gamma-ray Space Telescope , which is likely to be the second case of a γ -ray detection from a star-forming region (SFR) in our Galaxy. The LAT source is located in the G25 region, 1.°7 × 2.°1 around ( l , b ) = (25.°0, 0.°0). The γ -ray emission is found to be composed of two extended sources and one pointlike source. The extended sources have similar sizes of about 1.°4 × 0.°6. An ∼0.°4 diameter subregion of one has a photon index of Γ = 1.53 ± 0.15, and is spatially coincident with HESS J1837−069, likely a pulsar wind nebula. The other parts of the extended sources have a photon index of Γ = 2.1 ± 0.2 without significant spectral curvature. Given their spatial and spectral properties, they have no clear associations with sources at other wavelengths. Their γ -ray properties are similar to those of the Cygnus cocoon SFR, the only firmly established γ -ray detection of an SFR in the Galaxy. Indeed, we find bubble-like structures of atomic and molecular gas in G25, which may be created by a putative OB association/cluster. The γ -ray emitting regions appear confined in the bubble-like structure; similar properties are also found in the Cygnus cocoon. In addition, using observations with the XMM-Newton , we find a candidate young massive OB association/cluster G25.18+0.26 in the G25 region. We propose that the extended γ -ray emission in G25 is associated with an SFR driven by G25.18+0.26. Based on this scenario, we discuss possible acceleration processes in the SFR and compare them with the Cygnus cocoon.

79 ASTRONOMY AND ASTROPHYSICS↗

ORIGIN OF ULTRA-HIGH-ENERGY GALACTIC COSMIC RAYS: THE ISOTROPY PROBLEM

We study the propagation of ultra-high-energy cosmic rays (UHECRs) in the Galaxy, concentrating on the energy range below the ankle in the spectrum at 4 EeV. A Monte Carlo method, based on analytical solutions to the time-dependent diffusion problem, is used to account for intermittency by placing sources at random locations. Assuming a source population that scales with baryon mass density or star formation (e.g., long GRB), we derive constraints arising from intermittency and the observational limits on the composition and anisotropy. It is shown that the composition and anisotropy at 10{sup 18} eV are difficult to reproduce and require that either (1) the particle mean free path is much smaller than a gyroradius, implying the escape time is very long, (2) the composition is heavier than suggested by recent Auger data, (3) the ultra-high-energy sub-ankle component is mostly extragalactic, or (4) we are living in a rare lull in the UHECR production, and the current UHECR intensity is far below the Galactic time average. We therefore recommend a strong observational focus on determining the UHECR composition around 10{sup 18} eV.

79 ASTRONOMY AND ASTROPHYSICS↗

Observations of continuum X-ray and gamma-ray emission from the galactic center

A review of observations of the galactic nucleus to date in the X ray and gamma ray regions is presented. Attention is given to data in the 1-10 keV, 10-100 keV, 100 keV to 10 MeV, and 10 MeV to 1 GeV ranges. It is shown that the galactic nucleus is as yet unresolvable from the other galactic center at energies above 4.5 keV, while large variations in the observed flux in the 100 keV-1 MeV range indicate a single source as the dominant emitter. An X ray source is concluded to be contained in the nucleus, which features a constant luminosity of 1.5 x 10 to the 35th erg/sec in the 0.5-4.5 keV band. A hard and bright source is located near the nucleus, whose emitter source exists at a temperature of about 10 billion K with a luminosity 30 times that of the Crab Nebula.

Matteson, J. L.↗

Galactic 0.511 MeV line emission

Observations over two decades with various balloon-borne instruments and instruments on HEAO 3, SMM, and Compton Gamma Ray Observatory (CGRO) have revealed the existence of strong 0.511 MeV line emission from the direction of the Galactic center. We have attempted to fit the spatial distribution of this emisssion with distributions of various Galactic constituents, but found that none of these distributions alone could fit the data. Of the assumed distributions, those of Galactic novae and hot (10(exp 8) K) plasma are the most strongly peaked at the Galactic center. But we found that the 0.511 MeV line emission is even more strongly peaked. This new result is the direct consequence of the analysis of recent data obtained with the OSSE instrument on CGRO. We have thus considered two-component models consisting of an enhanced central Galactic component superposed on a Galactic plane component given by any one of our previously assumend distributions. For the central Galactic component we take either a single point source at the location of the source of annihilation radiation 1E 1740.7-2942 or an extended spheroidal distribution of several hundred parsecs in size. We find acceptable fits in both cases. We suggest that this additional component of the emission from the Galactic center region is due to positrons produced near one or more black holes. Such a component was also suggested by the variability of the 0.511 MeV line flux observed with balloon-borne high-resolution detectors. To produce the very narrow line observed by these high-resolution detectors at almost precisely 0.511 MeV the positrons must escape from the vicinity of the holes and annihilate in the surrounding interstellar medium. We have reexamined the issure of the time variability of the 0.511 MeV line emission. Although the significance of the variability implied by all of the earlier observations is diminished by a large number of recent OSSE observations which show no variability, the latter measurements merely indicate that the flux remained relatively constant only over a period of about 1 year (1991-1992). Positron producation in the Galactic center region by a small number of variable sources would lead to variable 0.511 MeV line emission. The timescale of the variation depends on the density of the gas in which the positrons annihilate. It could be as short as several months if the annihilation is in dense moleduar clouds, but would be much longer and essentially undetectable if the positrons annihilate in lower density interstellar gas.

Ramaty, R.↗

Calculation of Ambient (H*(10)) and Personal (H p (10)) Dose Equivalent from a 252 Cf Neutron Source

The neutron emission rate from radioisotope neutron sources such as 252 Cf sources can be calibrated by the National Institute of Standards and Technology (NIST) by the manganous sulfite bath method. This calibration method does not compute the dose or dose equivalent rate from the source. Because there is no accepted transfer standard for neutron dose measurements, secondary calibration facilities are responsible for determining their own neutron dose factors. This report describes a neutron source and irradiation apparatus in use at the Pacific Northwest National Laboratory Calibration Facility. The neutron source is a SR-Cf-3000 design 252 Cf neutron source. The neutron source is contained in an aluminum transfer capsule that is used to transport the neutron source between its storage location and it’s irradiation location. During irradiations, the source is located in a transfer tube assembly that consists of two concentric aluminum tubes. When moderated neutrons are desired, the transfer tube assembly is surrounded by a sphere that is filled with D 2 O as a moderating medium. Ambient dose equivalent (H*(10)) and Personal dose equivalent (H p (10)) dose rates and dose conversion factors were calculated for moderated and unmoderated neutron spectra based on the data provided in ICRP Publication 74. The neutron fluence-to-dose-equivalent conversion factors calculated for this report are summarized and compared to published values in Table 47. The calculated coefficients for the unmoderated 252 Cf spectra agree very well with published reference values, within about 2%. The calculated coefficients for the D 2 O moderated 252 Cf spectra, however, differ from published reference values by about 22%. The PNNL coefficients are higher than the published values which could be interpreted to mean that the PNNL D 2 O moderated spectrum is harder, i.e. higher average energy, than the spectrum published by the ISO (2000), which formed the basis for the published coefficients. The D 2 O moderating sphere in use at PNNL contains less D 2 O moderator than did the D 2 O moderating sphere that was used to calculate the ISO spectrum and this is the likely reason for much of the spectral differences. The exact location of the 252 Cf activity in the source encapsulation is unknown. Preliminary measurements, not described in this report, indicate that the activity may be offset from the location that has been assumed in the past. Corrections for the offset are being proposed and will be the subject of another report. This report was written in a calculation package format to help meet various Quality Assurance requirements.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Improving relative earthquake locations using surface-wave source corrections

SUMMARY We develop a procedure to improve estimates of relative earthquake locations using Rayleigh and Love wave arrivals for multiple earthquakes recorded at common stations. We fit predicted differential traveltimes to those measured using a cross-correlation technique, and correct the phases of the cross-correlation functions for phase delays that result from the surface-wave radiation patterns. We develop an empirical measure of uncertainty that provides realistic estimates of the errors in the earthquake locations. We investigate the effectiveness of the relocation procedure by first applying it to two suites of synthetic earthquakes. We then relocate real earthquakes in three separate regions: two ridge-transform systems and one subduction zone. We demonstrate that the inclusion of source corrections in the relocation procedure results in improved location estimates compared to relocations without source corrections. The source correction also allows for automated application of the relocation procedure, even in regions with a wide range of earthquake focal mechanisms.

Geochemistry & Geophysics↗

Scorpius X-1 - Origin of the radio and hard X-ray emissions

The consequences of models for the central radio source and the hard X-ray emitting region in Sco X-1 are examined. The radio emission could result from noncoherent synchrotron radiation, and the X-rays may be produced by bremsstrahlung. It is shown that both these mechanisms require a mass outflow from Sci X-1. The radio source is located at about 30 million km from the center of the star, and its linear dimensions do not exceed 300 million km. The magnetic field in the radio source is on the order of 1 gauss. If the hard X-rays are produced by thermal bremsstrahlung, their source is located between 10,000 and 50,000 km from the center of the star, the temperature is 2 billion K, and the emission measure is 2 times 10 to the 56th power per cu cm. This hot plasma loses energy inward by conduction and outward by supersonic expansion. The rates of energy loss for both of these processes are about 10 to the 36th ergs per sec, comparable to the total luminosity of Sco X-1.

Ramaty, R.↗

Site Characterization of the Source Physics Experiment Phase II Location Using Seismic Reflection Data

An objective of the Source Physics Experiment (SPE) is to identify low-yield nuclear explosions from a regional distance. Low-yield nuclear explosions can often be difficult to discriminate among the clutter of natural and man-made explosive events (e.g., earthquakes and mine blasts). The SPE is broken into three phases. Phase I has provided the first of the physics-based data to test the empirical models that have been used to discriminate nuclear events. The Phase I series of tests were placed within a highly fractured granite body. The evolution of the project has led to development of Phase II, to be placed within the opposite end member of geology, an alluvium environment, thereby increasing the database of waveforms to build upon in the discrimination models. Both the granite and alluvium sites have hosted nearby nuclear tests, which provide comparisons for the chemical test data. Phase III of the SPE is yet to be determined.

Seismic↗

SCO X-1: Origin of the radio and hard X-ray emissions

The consequences of models for the central radio source and the hard X-ray ( 30 keV) emitting region in Sco X-1 are examined. It was found that the radio emission could result from noncoherent synchrotron radiation and that the X-rays may be produced by bremsstrahlung. It is shown that both mechanisms require a mass outflow from Sco X-1. The radio source is located at r approximately 3x10 to the 12th power cm from the center of the star, and its linear dimensions do not exceed 3x10 to the 13th power cm. The magnetic field in the radio source is on the order of 1 gauss. If the hard X-rays are produced by thermal bremsstrahlung, their source is located at 10 to the 9th power approximately r approximately 5x10 to the 9th power cm, the temperature is 2x10 to the 9th power K, and the emission measure is 2x10 to the 56th power/cu cm. This hot plasma loses energy inward by conduction and outward by supersonic expansion. The rates of energy loss for both processes are about 10 to the 36th power erg/s, comparable to the total luminosity of Sco X-1.

Ramaty, R.↗

Apparatus and methods for location and sizing of trace gas sources

A system for detecting gas leaks and determining their location and size. A data gathering portion of the system utilizes a chosen geometrical configuration to collect path-integrated spectroscopic data over multiple paths around an area. A processing portion of the system applies a transport model together with meteorological data of the area to generate an influence function of possible leak locations on gas detector measurement paths, and applies an inversion model to the influence function, prior data, and the spectroscopic data to generate gas source size and location.

03 NATURAL GAS↗

Constraints on the mass-radius relation for the neutron star in the X-ray burst source 4U/MXB 1820-30 located in the globular cluster NGC 6624

From the spectral evolution of seven X-ray bursts observed from 4U/MXB 1820-30 (Haberl et al., 1986) during the phases of photospheric expansion and cooling, constraints are derived on the mass-radius relation of the neutron star in this system. Taking into account the uncertainty in the source distance and the possible anisotropy of the burst emission. If during bursts with radius expansion the outer layers of the neutron star are of a hydrogen-poor composition, none of the current equations of state of high-density matter is excluded. For a hydrogen-rich composition, only very soft equations of state are allowed.

Van Paradijs, J.↗

TRISCAN Antenna-Positioning Algorithm

TRISCAN scanning algorithm improves alinement between boresight of radar antenna and target. Algorithm originally developed for digitally pointed antennas in deep-space network; however, is possibly used in locating radio sources on Earth. TRISCAN estimates coordinate errors in hour angle and declination between predicted and true locations of radio source.

Bunce, R. C.↗

Spectral infrared hemispherical reflectance measurements for LDEF tray clamps

This paper describes infrared hemispherical reflectance measurements (2-15 microns) that were made on 58 chromic acid anodized tray clamps retrieved from the LDEF spacecraft. These clamps were used for maintaining the experiments in place and were located at various locations about the spacecraft. Changes in reflectance of the tray clamps at these locations were compared with atomic oxygen fluxes at the same locations. A decrease in absorption band depth was seen for the surfaces exposed to space indicating that there was some surface layer erosion. In all of the surfaces measured, little evidence of contamination was observed and none of the samples showed evidence of the brown nicotine stain that was so prominent in other experiments. Total emissivity values were calculated for both exposed and unexposed tray clamp surfaces. Only small differences, usually less than 1 percent, were observed. The spectral reflectances were measured using a hemi-ellipsoidal mirror reflectometer matched with an interferometer spectrometer. The rapid scanning capability of the interferometer allowed the reflectance measurements to be made in a timely fashion. The ellipsoidal mirror has its two foci separated by 2 inches and located on the major axis. A blackbody source was located at one focus while the tray clamp samples were located at the conjugate focus. The blackbody radiation was modulated and then focused by the ellipsoid onto the tray clamps. Radiation reflected from the tray clamp was sampled by the interferometer by viewing through a hole in the ellipsoid. A gold mirror (reflectance approximately 98 percent) was used as the reference surface.

Wood, Bobby E.↗