Search NASA⌕ Search

SEARCH · Search NASA

Results for “temperature changes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Thermomechanical buckling of multilayered composite panels with cutouts

A study is made of the thermomechanical buckling of flat unstiffened composite panels with central circular cutouts. The panels are subjected to combined temperature changes and applied edge loading (or edge displacements). The analysis is based on a first-order shear deformation plate theory. A mixed formulation is used with the fundamental unknowns consisting of the generalized displacements and the stress resultants of the plate. Both the stability boundary and the sensitivity coefficients are evaluated. The sensitivity coefficients measure the sensitivity of the buckling response to variations in the different lamination and material parameters of the panel. Numerical results are presented showing the effects of the variations in the hole diameter, laminate stacking sequence, fiber orientation, and aspect ratio of the panel on the thermomechanical buckling response and its sensitivity coefficients.

Noor, Ahmed K.↗
NASA NTRS1993

Transient motion of a confined rarefied gas due to wall heating or cooling

The direct Monte Carlo method is used to simulate the transient motion of a confined rarefied gas as a container wall is rapidly heated or cooled. Results show that, for the rapid wall temperature changes, the gas response is better measured by an acoustic, rather than conduction, timescale, with steady state conditions being achieved after about ten wave crossing times.

Wadsworth, Dean C.↗
NASA NTRS1992

A cryogenic multichannel electronically scanned pressure module

Consideration is given to a cryogenic multichannel electronically scanned pressure (ESP) module developed and tested over an extended temperature span from -184 to +50 C and a pressure range of 0 to 5 psig. The ESP module consists of 32 pressure sensor dice, four analog 8 differential-input multiplexers, and an amplifier circuit, all of which are packaged in a physical volume of 2 x 1 x 5/8 in with 32 pressure and two reference ports. Maximum nonrepeatability is measured at 0.21 percent of full-scale output. The ESP modules have performed consistently well over 15 times over the above temperature range and continue to work without any sign of degradation. These sensors are also immune to repeated thermal shock tests over a temperature change of 220 C/sec.

Shams, Qamar A.↗
NASA NTRS1992

A comparison of synoptic-scale development characteristics for over-water and over-land cases of explosive cyclone development

The Zwack and Okossi (1986) equation is here demonstrated to be an effective tool for the diagnosis of synoptic-scale cyclone development, and is noted to indicate that cyclonic vorticity advection is the most consistent contributor to the explosive development of a given cyclone. Warm air advection and latent heat release also contributed to explosive development in varying degrees. The adiabatic temperature changes forced by vertical motion opposed the development of both over-water and over-land cyclone development.

Lupo, Anthony R.↗
NASA NTRS1993

Radiative feedback of polar stratospheric clouds on Antarctic temperatures

A one-dimensional time marching radiative transfer model has been used to investigate the potential effects of polar stratospheric clouds (PSCs) on winter and spring temperatures in the Antarctic lower stratosphere. High, middle, and low PSC amounts were specified from lidar backscatter profiles and were chosen to represent the likely range of PSC amounts present in the Antarctic region. The computed effects of the PSCs on temperatures depend strongly on the surface temperature and on the extent of tropospheric cloudiness, and range from a maximum increase of 6 K for a high amount of PSCs over a warm surface and clear troposphere to a maximum decrease of 2 K for a high amount of PSCs over a cold surface and a troposphere with high clouds. The average effect is unlikely to be more than a 1 or 2 K temperature change.

Rosenfeld, Joan E.↗
NASA NTRS1955

Recovery and Time-response Characteristics of Six Thermocouple Probes in Subsonic and Supersonic Flow

Experimental data obtained from three shielded and three unshielded thermocouple probes are presented. Data taken in air at room temperature over the ranges 0.2 to 2.2 Mach number and 0.2 to 2.2 atmospheres total pressure show reproducible systematic variations of recovery with Mach number, ambient pressure, flow angle, and probe design. Time-constant data determined at Mach 0.2 and room temperature and pressure indicate that unshielded probes are several times faster in response to temperature changes than shielded probes.

Stickney, Truman M↗
NASA NTRS1951

Velocity and Temperature Fields in Circular Jet Expanding from Choked Nozzle into Quiescent Air

The Mach number and temperature profiles in jets expanding from convergent and convergent-divergent nozzles are presented for several values of nozzle-exit pressure ratio. The effects of jet temperature, Reynolds number, and humidity on jet spreading are briefly evaluated. The results indicated that the downstream Mach number profiles for a heated jet are slightly narrower than those for a unheated jet, whereas the downstream temperature profiles were unaffected by nozzle temperature change, and that the effects of Reynolds number and humidity were negligible.

FLOW, SUPERSONIC↗
NASA NTRS1945

Method of Matching Performance of Compressor Systems with that of Aircraft Power Sections

A method is developed of easily determining the performance of a compressor system relative to that of the power section for a given altitude. Because compressors, reciprocating engines, and turbines are essentially flow devices, the performance of each of these power-plant components is presented in terms of similar dimensionless ratios. The pressure and temperature changes resulting from restrictions of the charge-air flow and from heat transfer in the ducts connecting the components of the power plant are also expressed by the same dimensionless ratios and the losses are included in the performance of the compressor. The performance of a mechanically driven, single-stage compressor in relation to the performance of a conventional air-cooled engine operating at sea-level conditions is presented as an example of the application of the method.

Bullock, Robert O.↗
NASA NTRS1993

A wide-band fiber optic frequency distribution system employing thermally controlled phase compensation

An active wide-band fiber optic frequency distribution system employing a thermally controlled phase compensator to stabilize phase variations induced by environmental temperature changes is described. The distribution system utilizes bidirectional dual wavelength transmission to provide optical feedback of induced phase variations of 100 MHz signals propagating along the distribution cable. The phase compensation considered differs from earlier narrow-band phase compensation designs in that it uses a thermally controlled fiber delay coil rather than a VCO or phase modulation to compensate for induced phase variations. Two advantages of the wide-band system over earlier designs are (1) that it provides phase compensation for all transmitted frequencies, and (2) the compensation is applied after the optical interface rather than electronically ahead of it as in earlier schemes. Experimental results on the first prototype shows that the thermal stabilizer reduces phase variations and Allan deviation by a factor of forty over an equivalent uncompensated fiber optic distribution system.

Johnson, Dean↗
NASA NTRS1993

Mechanical energy absorber

An energy absorbing system for controlling the force where a moving object engages a stationary stop and where the system utilized telescopic tubular members, energy absorbing diaphragm elements, force regulating disc springs, and a return spring to return the telescoping member to its start position after stroking is presented. The energy absorbing system has frusto-conical diaphragm elements frictionally engaging the shaft and are opposed by a force regulating set of disc springs. In principle, this force feedback mechanism serves to keep the stroking load at a reasonable level even if the friction coefficient increases greatly. This force feedback device also serves to desensitize the singular and combined effects of manufacturing tolerances, sliding surface wear, temperature changes, dynamic effects, and lubricity.

Wesselski, Clarence J.↗
NASA NTRS1993

Long-Term Monitoring of Global Climate Forcings and Feedbacks

A workshop on Long-Term Monitoring of Global Climate Forcings and Feedbacks was held February 3-4, 1992, at NASA's Goddard Institute for Space Studies to discuss the measurements required to interpret long-term global temperature changes, to critique the proposed contributions of a series of small satellites (Climsat), and to identify needed complementary monitoring. The workshop concluded that long-term (several decades) of continuous monitoring of the major climate forcings and feedbacks is essential for understanding long-term climate change.

Hansen, J.↗
NASA NTRS1994

Radiometer calibration procedure and beacon attenuation estimation reference level

The primary objectives are to compare radiometer attenuation with beacon attenuation and to compare sky temperature estimates with calculations using simultaneous meteorological data. Secondary objectives are: (1) noise diode and reference load measurements and (2) to adjust for outside temperature and component temperature changes.

Crane, Robert K.↗
NASA NTRS1995

Thermoelastic Theory for the Response of Materials Functionally Graded in Two Directions with Applications to the Free-Edge Problem

A recently developed micromechanical theory for the thermoelastic response of functionally graded composites with nonuniform fiber spacing in the through-thickness direction is further extended to enable analysis of material architectures characterized by arbitrarily nonuniform fiber spacing in two directions. In contrast to currently employed micromechanical approaches applied to functionally graded materials, which decouple the local and global effects by assuming the existence of a representative volume element at every point within the composite, the new theory explicitly couples the local and global effects. The analytical development is based on volumetric averaging of the various field quantities, together with imposition of boundary and interfacial conditions in an average sense. Results are presented that illustrate the capability of the derived theory to capture local stress gradients at the free edge of a laminated composite plate due to the application of a uniform temperature change. It is further shown that it is possible to reduce the magnitude of these stress concentrations by a proper management of the microstructure of the composite plies near the free edge. Thus by an appropriate tailoring of the microstructure it is possible to reduce or prevent the likelihood of delamination at free edges of standard composite laminates.

Aboudi, Jacob↗
NASA NTRS1995

Thermomechanical postbuckling of multilayered composite panels with cutouts

The results of a study of the detailed thermomechanical postbuckling response characteristics of flat unstiffened composite panels with central circular cutouts are presented. The panels are subjected to combined temperature changes and applied edge loading (or edge displacements). The analysis is based on a first-order shear deformation plate theory. A mixed formulation is used with the fundamental unknowns consisting of the generalized displacements and the stress resultants of the plate. The postbuckling displacements, transverse shear stresses, transverse shear strain energy density, and their sensitivity coefficients are evaluated. The sensitivity coefficients measure the sensitivity of the post-buckling response to variations in the different lamination and material parameters of the panel. Numerical results are presented showing the effects of the variations in the hole diameter, laminate stacking sequence, fiber orientation, and aspect ratio of the panel on the thermomechanical postbuckling response and its sensitivity to changes in panel parameters.

Noor, Ahmed K.↗
NASA NTRS1995

Three-dimensional solutions for coupled thermoelectroelastic response of multilayered plates

Analytic three-dimensional solutions are presented for the coupled thermoelectroelastic response of multilayered hybrid composite plates. The plates consist of a combination of fiber-reinforced cross-ply and piezothermoelastic layers. Both the thermoelectroelastic static response and its sensitivity coefficients are computed. The sensitivity coefficients measure the sensitivity of the response to variations in different mechanical, thermal and piezoelectric material properties of the plate. A linear constitutive model is used, and the material properties are assumed to be independent of the temperature and the electric field. The plates are assumed to have rectangular geometry and special material symmetries. A mixed formulation is used with the fundamental unknowns consisting of the three transverse stress components; three displacement components; transverse component of the electric displacement field; electric potential; transverse heat flux component, and temperature change. Each of the fundamental unknowns is expressed in terms of a double Fourier series in the Cartesian surface coordinates. A state space approach is used to generate the static response and to evaluate the sensitivity coefficients. Extensive numerical results are presented showing the effects of variation in the geometric parameters of the plate on the different response quantities and their sensitivity coefficients.

Xu, Kangming↗
NASA NTRS1995

Preventing Cracking of Anodized Coatings

Anodized coatings have been used as optical and thermal surfaces in spacecraft. Particulate contamination from cracked coatings is a concern for many applications. The major cause for the cracking is the difference in the coefficient of thermal expansion between the oxide coatings and the aluminum substrate. The loss of water when the coating is exposed to a vacuum also could induce cracking of the coating. Hot-water sealing was identified as the major cause for the cracking of the coatings because of the large temperature change when the parts were immersed in boiling water and the water was absorbed in the coating. when the hot-water sealing process was eliminated, the cracking resistance of the anodized coatings was greatly improved. Also, it was found that dyed black coatings were more susceptible than clear coatings to cracking during thermo-vacuum cyclings.

He, Charles C.↗
NASA NTRS1994

Protein crystal growth in microgravity: Temperature induced large scale crystallization of insulin

One of the major stumbling blocks that prevents rapid structure determination using x-ray crystallography is macro-molecular crystal growth. There are many examples where crystallization takes longer than structure determination. In some cases, it is impossible to grow useful crystals on earth. Recent experiments conducted in conjuction with NASA on various Space Shuttle missions have demonstrated that protein crystals often grow larger and display better internal molecular order than their earth-grown counterparts. This paper reports results from three Shuttle flights using the Protein Crystallization Facility (PCF). The PCF hardware produced large, high-quality insulin crystals by using a temperature change as the sole means to affect protein solubility and thus, crystallization. The facility consists of cylinders/containers with volumes of 500, 200, 100, and 50 ml. Data from the three Shuttle flights demonstrated that larger, higher resolution crystals (as evidenced by x-ray diffraction data) were obtained from the microgravity experiments when compared to earth-grown crystals.

Long, Marianna M.↗
NASA NTRS1994

High-Speed Hubble Space Telescope Ultraviolet photometry of two DB white dwarfs: Nonradial and radial pulsations

We observed two DB white dwarf stars with the High Speed Photometer aboard the Hubble Space Telescope. The two targets, the nonradial pulsator GD 358, and PG 0112+104, a non-pulsating white dwarf with similar temperature, were each observed for 1800 s with a time resolution of 10 ms. We used the F140LP configuration, which gives a broadband response in the UV between 1400 and 3000 A. The data clearly show the long period (about 700 s) pulsations in GD 358. Comparison with optical observations obtained two weeks earlier shows that the amplitude of the pulsations in the UV is approximately 1.4 times higher, consistent with nonradial pulsations due solely to temperature changes at constant radius. The high time resolution of these observations allows us to search for high-frequency pulsations (such as p modes or high overtone radial modes). No firm evidencefor high-frequency pulsations was seen in either object between 1 and 12 Hz. Correlation analysis of GD 358 shows no clear signal of multifrequency high overtone radial pulsations at the 0.00075 mag level, with no individual modes above the 0.0016 mag level. Upper limits for PG 0112+104 are approximately 2 times higher than for GD 358. Implications of this study for the theory of white dwarf pulsations are discussed.

Kawaler, Steven D.↗