Search NASA⌕ Search

SEARCH · Search NASA

Results for “test correlation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Stress Wave Attenuation in Aluminum Alloy and Mild Steel Specimens Under SHPB Tensile Testing

Investigations on the effect of intensity of incident pressure wave applied through the striker bar on the specimen force histories and stress wave attenuation during split Hopkinson pressure bar (SHPB) tensile testing are presented. Details of the tensile SHPB along with Lagrangian x–t diagram of the setup are included. Studies were carried out on aluminum alloy 7075 T651 and IS 2062 mild steel. While testing specimens using the tensile SHPB setup, it was observed that the force calculated from the transmitter bar strain gauge was smaller than the force obtained from the incident bar strain gauge. This mismatch between the forces in the incident bar and the transmitter bar is explained on the basis of stress wave attenuation in the specimens. A methodology to obtain force histories using the strain gauges on the specimen during SHPB tensile testing is also presented. Further, scanning electron microscope images and photomicrographs are given. Correlation between the microstructure and mechanical properties is explained. Further, uncertainty analysis was conducted to ascertain the accuracy of the results.

36 MATERIALS SCIENCE↗

Single x-ray absorptiometry method for the quantitative mammographic measure of fibroglandular tissue volume

Purpose: This study describes the design and characteristics of a highly accurate, precise, and automated single-energy method to quantify percent fibroglandular tissue volume (%FGV) and fibroglandular tissue volume (FGV) using digital screening mammography. Methods: The method uses a breast tissue-equivalent phantom in the unused portion of the mammogram as a reference to estimate breast composition. The phantom is used to calculate breast thickness and composition for each image regardless of x-ray technique or the presence of paddle tilt. The phantom adheres to the top of the mammographic compression paddle and stays in place for both craniocaudal and mediolateral oblique screening views. We describe the automated method to identify the phantom and paddle orientation with a three-dimensional reconstruction least-squares technique. A series of test phantoms, with a breast thickness range of 0.5-8 cm and a %FGV of 0%-100%, were made to test the accuracy and precision of the technique. Results: Using test phantoms, the estimated repeatability standard deviation equaled 2%, with a {+-}2% accuracy for the entire thickness and density ranges. Without correction, paddle tilt was found to create large errors in the measured density values of up to 7%/mm difference from actual breast thickness. This new density measurement is stable over time, with no significant drifts in calibration noted during a four-month period. Comparisons of %FGV to mammographic percent density and left to right breast %FGV were highly correlated (r=0.83 and 0.94, respectively). Conclusions: An automated method for quantifying fibroglandular tissue volume has been developed. It exhibited good accuracy and precision for a broad range of breast thicknesses, paddle tilt angles, and %FGV values. Clinical testing showed high correlation to mammographic density and between left and right breasts.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

A Combined Pharmacokinetic and Radiologic Assessment of Dynamic Contrast-Enhanced Magnetic Resonance Imaging Predicts Response to Chemoradiation in Locally Advanced Cervical Cancer

Purpose: To investigate the combination of pharmacokinetic and radiologic assessment of dynamic contrast-enhanced magnetic resonance imaging (MRI) as an early response indicator in women receiving chemoradiation for advanced cervical cancer. Methods and Materials: Twenty women with locally advanced cervical cancer were included in a prospective cohort study. Dynamic contrast-enhanced MRI was carried out before chemoradiation, after 2 weeks of therapy, and at the conclusion of therapy using a 1.5-T MRI scanner. Radiologic assessment of uptake parameters was obtained from resultant intensity curves. Pharmacokinetic analysis using a multicompartment model was also performed. General linear modeling was used to combine radiologic and pharmacokinetic parameters and correlated with eventual response as determined by change in MRI tumor size and conventional clinical response. A subgroup of 11 women underwent repeat pretherapy MRI to test pharmacokinetic reproducibility. Results: Pretherapy radiologic parameters and pharmacokinetic K{sup trans} correlated with response (p < 0.01). General linear modeling demonstrated that a combination of radiologic and pharmacokinetic assessments before therapy was able to predict more than 88% of variance of response. Reproducibility of pharmacokinetic modeling was confirmed. Conclusions: A combination of radiologic assessment with pharmacokinetic modeling applied to dynamic MRI before the start of chemoradiation improves the predictive power of either by more than 20%. The potential improvements in therapy response prediction using this type of combined analysis of dynamic contrast-enhanced MRI may aid in the development of more individualized, effective therapy regimens for this patient group.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Analysis of the Source Physics Experiment Dry Alluvium Geology Ball Drop Sources

Two balls were dropped approximately 150 m down an open borehole as part of an investigation into the aftershocks from a 51 ton TNT-equivalent chemical explosion. The ball drop sources, a concrete-filled basketball and a bowling ball, were intended to mimic falling debris within an underground explosion borehole and cavity. Falling debris or sloughing of the borehole and cavity walls is thought to be one of the sources of explosion aftershocks. The signals from the ball drop sources were recorded by the same seismic network that monitored the aftershocks of the chemical explosion, so the ball drop recordings were used as templates to search through the continuous stream of aftershocks and detect correlated signals as a proportion of all aftershocks. The search resulted in only four similar event recordings out of the thousands of detected aftershocks. A synthetic test showed that the small, high-frequency ball drop templates were limited to producing highly correlated detections for events occurring in a small region around the impact location at 150 m depth. The high-frequency templates were necessary since the small ball drop signals were only above the noise at frequencies greater than 10 Hz. Unfortunately, the impact location is where the borehole was filled with sand in preparation for the subsequent chemical explosion in the test series, making it 150 m above the explosion created cavity centered at 300 m depth. This puts the ball drop templates 150 m away from the cavity, where many more events from falling debris would be expected. Further synthetic tests confirmed events emanating from the cavity 150 m below the impact site would have correlated with the lower frequency template and been detected had the template been usable below 10 Hz. Therefore, we conclude that the four detected events were most probably falling debris within the open borehole that impacted the floor at 150 m depth just as the ball drop sources had, and that this type of explosion aftershock mechanism comprises less than 1% of all explosion aftershocks.

58 GEOSCIENCES↗

Use of the Wilshire Equations to Correlate and Extrapolate Creep Data of Inconel 617 and Nimonic 105

Advanced power plant alloys must endure high temperatures and pressures for durations at which creep data are often not available, necessitating the extrapolation of creep life. A recently developed creep life extrapolation method is the Wilshire equations, with which multiple approaches can be used to increase the goodness of fit of available experimental data and improve the confidence level of calculating long-term creep strength at times well beyond the available experimental data. In this article, the Wilshire equation is used to extrapolate the creep life of Inconel 617 and Nimonic 105 to 100,000 h. The use of (a) different methods to determine creep activation energy, (b) region splitting, (c) heat- and processing-specific tensile strength data, and (d) short-duration test data were investigated to determine their effects on correlation and extrapolation. For Inconel 617, using the activation energy of lattice self-diffusion as Q C * resulted in a poor fit with the experimental data. Additionally, the error of calculated rupture times worsened when splitting regions. For Nimonic 105, the error was reduced when heat- and processing-specific tensile strengths were used. Extrapolating Inconel 617 creep strength to 100,000 h life gave conservative results when compared to values calculated by the European Creep Collaborative Committee.

36 MATERIALS SCIENCE↗

Integral Reactor Containment Condensation Model and Experimental Validation

This NEUP funded project, NEUP 12-3630, is for experimental, numerical and analytical studies on high-pressure steam condensation phenomena in a steel containment vessel connected to a water cooling tank, carried out at Oregon State University (OrSU) and the University of Wisconsin at Madison (UW-Madison). In the three years of investigation duration, following the original proposal, the planned tasks have been completed: (1) Performed a scaling study for the full pressure test facility applicable to the reference design for the condensation heat transfer process during design basis accidents (DBAs), modified the existing test facility to route the steady-state secondary steam flow into the high pressure containment for controllable condensation tests, and extended the operations at negative gage pressure conditions (OrSU). (2) Conducted a series of DBA and quasi-steady experiments using the full pressure test facility to provide a reliable high pressure condensation database (OrSU). (3) Analyzed experimental data and evaluated condensation model for the experimental conditions, and predicted the prototypic containment performance under accidental conditions (UW-Madison). A film flow model was developed for the scaling analysis, and the results suggest that the 1/3 scaled test facility covers large portion of laminar film flow, leading to a lower average heat transfer coefficient comparing to the prototypic value. Although it is conservative in reactor safety analysis, the significant reduction of heat transfer coefficient (50%) could under estimate the prototypic condensation heat transfer rate, resulting in inaccurate prediction of the decay heat removal capability. Further investigation is thus needed to quantify the scaling distortion for safety analysis code validation. Experimental investigations were performed in the existing MASLWR test facility at OrST with minor modifications. A total of 13 containment condensation tests were conducted for pressure ranging from 4 to 21 bar with three different static inventories of non-condensable gas. Condensation and heat transfer rates were evaluated employing several methods, notably from measured temperature gradients in the HTP as well as measured condensate formation rates. A detailed mass and energy accounting was used to assess the various measurement methods and to support simplifying assumptions required for the analysis. Condensation heat fluxes and heat transfer coefficients are calculated and presented as a function of pressure to satisfy the objectives of this investigation. The major conclusions for those tests are summarized below: (1) In the steam blow-down tests, the initial condensation heat transfer process involves the heating-up of the containment heat transfer plate. An inverse heat conduction model was developed to capture the rapid transient transfer characteristics, and the analysis method is applicable to SMR safety analysis. (2) The average condensation heat transfer coefficients for different pressure conditions and non-condensable gas mass fractions were obtained from the integral test facility, through the measurements of the heat conduction rate across the containment heat transfer plate, and from the water condensation rates measurement based on the total energy balance equation. 15 (3) The test results using the measured HTP wall temperatures are considerably lower than popular condensation models would predict mainly due to the side wall conduction effects in the existing MASLWR integral test facility. The data revealed the detailed heat transfer characteristics of the model containment, important to the SMR safety analysis and the validation of associated evaluation model. However this approach, unlike separate effect tests, cannot isolate the condensation heat transfer coefficient over the containment wall, and therefore is not suitable for the assessment of the condensation heat transfer coefficient against system pressure and noncondensable gas mass fraction. (4) The average condensation heat transfer coefficients measured from the water condensation rates through energy balance analysis are appropriate, however, with considerable uncertainties due to the heat loss and temperature distribution on the containment wall. With the consideration of the side wall conduction effects, the results indicate that the measured heat transfer coefficients in the tests is about 20% lower than the prediction of Dehbi’s correlation, mainly due to the side wall conduction effects. The investigation also indicates an increase in the condensation heat transfer coefficient at high containment pressure conditions, but the uncertainties invoked with this method appear to be substantial. (5) Non-condensable gas in the tests has little effects on the condensation heat transfer at high elevation measurement ports. It does affect the bottom measurements near the water level position. The results suggest that the heavier non-condensable gas is accumulated in the lower portion of the containment due to stratification in the narrow containment space. The overall effects of the non-condensable gas on the heat transfer process should thus be negligible for tall containments of narrow condensation spaces in most SMR designs. Therefore, the previous correlations with noncondensable gas effects are not appropriate to those small SMR containments due to the very poor mixing of steam and non-condensable gas. The MELCOR simulation results agree with the experimental data reasonably well. However, it is observed that the MELCOR overpredicts the heat flux for all analyzed tests. The MELCOR predicts that the heat fluxes for CCT’s approximately range from 30 to 45 kW/m2 whereas the experimental data (averaged) ranges from about 25 to 40 kW/m2. This may be due to the limited availability of liquid film models included in MELCOR. Also, it is believed that due to complex test geometry, measured temperature gradients across the heat transfer plate may have been underestimated and thus the heat flux had been underestimated. The MELCOR model predicts a film thickness on the order of 100 microns, which agrees very well with film flow model developed in this study for scaling analysis. However, the expected differences in film thicknesses for near vacuum and near atmospheric test conditions are not significant. Further study on the behavior of condensate film is expected to refine the simulation results. Possible refinements include but are not limited to, the followings: CFD simulation focusing on the liquid film behavior and benchmarking with experimental analyses for simpler geometries. 16 1 INTRODUCTION This NEUP funded project, NEUP 12-3630, is for experimental, numerical and analytical studies on high-pressure steam condensation phenomena in a steel containment vessel connected to a water cooling tank, carried out at Oregon State University (OrSU) and the University of Wisconsin at Madison (UW-Madison). The experimental results are employed to validate the containment condensation model in reactor containment system safety analysis code for integral SMRs. Such a containment condensation model is important to demonstrate the adequate cooling. In the three years of investigation, following the original proposal, the following planned tasks have been completed: (1) Performed a scaling study for the full pressure test facility applicable to the reference design for the condensation heat transfer process during design basis accidents (DBAs), modified the existing test facility to route the steady-state secondary steam flow into the high pressure containment for controllable condensation tests, and extended the operations at negative gage pressure conditions (OrSU). (2) Conducted a series of DBA and quasi-steady experiments using the full pressure test facility to provide a reliable high pressure condensation database (OrSU). (3) Analyzed experimental data and evaluated condensation model for the experimental conditions, and predicted the prototypic containment performance under accidental conditions (UW-Madison). The results are applicable to integral Small Modular Reactor (SMR) designs, including NuScale, mPower, Westinghouse SMR, Holtec-160 and other integral reactors with small containments of relatively high pressures under accidental conditions. Testing has been conducted at the OrSU laboratory in the existing MASLWR (Multi-Application Small Light Water Reactor) integral test facility sponsored by the US Department of Energy. Its highpressure stainless steel containment model (~2 MPa) is scaled to the NuScale SMR currently under development at NuScale Power, Inc.. Minor modifications to the model containment have been made to control the non-condensable gas fraction and to utilize the secondary loop stable steam flow for condensation testing. UW-Madison has developed a containment condensation model, which leveraged previous validated containment heat transfer work carried out at UW-Madison, and extended the range of applicability of the model to integral SMR designs that utilize containment vessels of high heat transfer efficiencies. In this final report, the research background and literature survey are presented in Chapter 2 and 3, respectively. The test facility description and modifications are summarized in Chapter 4, and the scaling analysis is introduced in Chapter 5. The tests description, procedures, and data analysis are presented in Chapter 6, while the numerical modeling is presented in Chapter 7, followed by a conclusion section in Chapter 8.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Evaluation of a Seismic Event, 12 May 2010, in North Korea

We assess seismological evidence bearing on claims that North Korea conducted a small nuclear test on 12 May 2010 in the vicinity of known underground nuclear tests in 2006, 2009, 2013, and 2016. First, we use Lg -wave cross-correlation and more traditional methods to locate the 2010 event between about 4 and 10 km southwest of the 2009 test. Second, we compare the relative sizes of regional P-waves and S-waves, using stations within 400 km of the known North Korean nuclear tests, to assess the nature of the event. We measured P / S ratios at different frequencies, at first using data from the open station MDJ in northeast China, for training sets of earthquakes and of explosions. We developed a linear discriminant function (LDF), that, in application to P / S measured at MDJ, is most effective in separating the earthquake and explosion populations. MDJ lacks usable data for the event of interest, but we have obtained regional data from stations of the nearby Dongbei Broadband Seismographic Network (DBSN), for the event of 12 May 2010 and for nearby underground nuclear tests conducted in 2006 and 2009. When our LDF is applied to DBSN data, and to data from stations SMT and NE3C in China, the LDF values measured from P/S ratios from known explosions are explosion-like; but for the event of 12 May 2010 the LDF values are earthquake-like for frequencies between 6 and 12 Hz. Furthermore, our method for characterizing earthquakes and explosions on the basis of their regional signals can be widely applied. Measurements of P / S based upon three-component waveform data provide better discrimination power than do those based upon vertical-component data alone.

58 GEOSCIENCES↗

EMR Coupling into Systems: Calibration of the Sandia Reverberation Chamber and Validation of the Single Slot Aperture Gain Model

Electromagnetic threats to weapon systems are always specified in terms of an incident plane wave. Sandia strongly prefers to test electromagnetic susceptibility in a reverberation chamber because a reverberant environment does not allow any potential point of entry to be shadowed. At the same time, a reverberation chamber averages out the directive gain of any points of entry. This would result in an under test of the system. Subsequently, a plane wave correction factor is needed to relate the plane wave and reverberation environments. Warne, et al, at Sandia have developed a theoretical correction factor and a previous attempt to validate it using an anechoic chamber (Higgins & Charley, Electromagnetic Radiation (EMR) Coupling into Complex Systems Aperture Coupling into Canonical Cavities in Reverberant and Anechoic Environments and Model Validation (SAND2007-7391), 2007) was not conclusive. In this current work the theoretical factor has been validated by creating the plane wave environment inside a gigahertz transverse electromagnetic (GTEM) cell instead of an anechoic chamber. The correlation is excellent at all but the lowest frequencies tested. The discrepancy in the low frequency regime is understood in terms of limits on the test capabilities.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Deposition Temperature on the Tribology of MOCVD Zinc Oxide Thin Films Tested under Dry Contact

Zinc oxide has justifiably been attracting attention in several fields, and the relatively new field of tribology is not left out. Aside from its already extensively researched and documented applications in materials science, semiconductor and electronics industry, zinc oxide nanoparticles and thin films appear to be gaining fast grounds as tribological materials, thereby justifying a zealous approach in further exploring their inherent properties in this area. In this work, zinc oxide thin films were deposited by MOCVD (metal-organic chemical vapour deposition) on soda lime glass andAISI304L stainless steel plates at temperatures of 300°C, 330°C, 360°C, 390°C and 420°C respectively, using anhydrous zinc acetate as the precursor. The carrier gas was air with a flow rate of 2.5 dm 3 min -1 at atmospheric pressure, and deposition time of 2 hours each. The thickness and tribological properties of the thin films produced were thereafter investigated. The thickness was measured by RBS (Rutherford backscattering spectroscopy) using a 1.7 MeV Tandem Accelerator, and the friction and wear properties were tested with a HFRR (high frequency reciprocating rig) under dry contact conditions, Olympus BH-2 Optical Microscope, and ADE Phase Shift MicroXam Optical Surface Profiler. The thickness was found to decrease with increasing deposition temperature, although for the 300°C deposition temperature there appeared to be a bloated thickness, which is attributable to such factors as incomplete precursor decomposition, turbulence in precursor flow, and energy straggling during RBS measurement. The friction tests highlighted coefficients of friction which were relatively low at the onset of the tests, but thereafter rapidly increased, owing possibly to temperature rise, attendant rapid oxidation and aided abrasion by worn debris. The average coefficient of friction of each test was computed, and the outcome (0.33 – 0.43) for all of them was a material still good enough for use in reducing friction at nanolevel, even with worn out matter and increased working temperature, with no noticeable trend regarding their varied deposition temperatures. Microscope and profilometer profiles vividly showed wear scars with material removal and material transfer. The average wear scar diameters as well as the wear volumes were compiled for both the test balls and the thin films. The result showed a largely correlated trend in the wear scar diameters and the wear volumes, and the thin film deposited at 330°C was the coating with the least wear scars, material removal cum transfer on the test ball and sample. This result is attributed to the enhanced thickness of the sample over the others, apart from sample X1 earlier reported to have a problem in its thickness. As a result, this temperature is therefore recommended as the optimum deposition temperature for the best tribologically applicable zinc oxide thin films, using zinc acetate precursor by MOCVD.

36 MATERIALS SCIENCE↗

Temporal Forecasting of Distributed Temperature Sensing in a Thermal Hydraulic System With Machine Learning and Statistical Models

We benchmark performance of long-short term memory (LSTM) network machine learning model and autoregressive integrated moving average (ARIMA) statistical model in temporal forecasting of distributed temperature sensing (DTS). Data in this study consists of fluid temperature transient measured with two co-located Rayleigh scattering fiber optic sensors (FOS) in a forced convection mixing zone of a thermal tee. We treat each gauge of a FOS as an independent temperature sensor. We first study prediction of DTS time series using Vanilla LSTM and ARIMA models trained on prior history of the same FOS that is used for testing. The results yield maximum absolute percentage error (MaxAPE) and root mean squared percentage error (RMSPE) of 1.58% and 0.06% for ARIMA, and 3.14% and 0.44% for LSTM, respectively. Next, we investigate zero-shot forecasting (ZSF) with LSTM and ARIMA trained on history of the co-located FOS only, which is advantageous when limited training data is available. The ZSF MaxAPE and RMSPE values for ARIMA are comparable to those of the Vanilla use case, while the error values for LSTM increase. We show that in ZSF, performance of LSTM network can be improved by training on most correlated gauges between the two FOS, which are identified by calculating the Pearson correlation coefficient. The improved ZSF MaxAPE and RMSPE for LSTM are 4.4% and 0.33%, respectively. Performance of ZSF LSTM can be further enhanced through transfer learning (TL), where LSTM is re-trained on a subset of the FOS that is the target of forecasting. We show that LSTM pre-trained on correlated dataset and re-trained on 30% of testing target dataset achieves MaxAPE and RMSPE values of 2.32% and 0.28%, respectively.

ARIMA↗

FY16 Status Report on Development of Integrated EPP and SMT Design Methods

The goal of the Elastic-Perfectly Plastic (EPP) combined integrated creep-fatigue damage evaluation approach is to incorporate a Simplified Model Test (SMT) data based approach for creep-fatigue damage evaluation into the EPP methodology to avoid the separate evaluation of creep and fatigue damage and eliminate the requirement for stress classification in current methods; thus greatly simplifying evaluation of elevated temperature cyclic service. The EPP methodology is based on the idea that creep damage and strain accumulation can be bounded by a properly chosen “pseudo” yield strength used in an elastic-perfectly plastic analysis, thus avoiding the need for stress classification. The original SMT approach is based on the use of elastic analysis. The experimental data, cycles to failure, is correlated using the elastically calculated strain range in the test specimen and the corresponding component strain is also calculated elastically. The advantage of this approach is that it is no longer necessary to use the damage interaction, or D-diagram, because the damage due to the combined effects of creep and fatigue are accounted in the test data by means of a specimen that is designed to replicate or bound the stress and strain redistribution that occurs in actual components when loaded in the creep regime. The reference approach to combining the two methodologies and the corresponding uncertainties and validation plans are presented. Results from recent key feature tests are discussed to illustrate the applicability of the EPP methodology and the behavior of materials at elevated temperature when undergoing stress and strain redistribution due to plasticity and creep.

42 ENGINEERING↗

Automated qualification data tool for high temperature metallic materials

This report describes a framework for storing, processing, and displaying qualification data for high temperature mechanical properties. The framework automates the process of generating design data from mechanical test results, for example for a data qualification report for the ASME Boiler \& Pressure Vessel Code. The framework has three parts: a data storage model with common formats for several types of typical mechanical property tests, a backend based on the \pycreep Python library for correlating and extrapolating the data to generate design material properties and allowable stresses, and a demonstration user interface for displaying, sorting, and filtering the data and exploring different options for modeling the design mechanical properties. The report discusses the options available for data processing, with illustrations from real test data on Alloy 617, Alloy 709, Alloy 740H, and Laser-Powder Bed Fusion 316H. The framework is complete for ASME type data analysis and will be used to store test data generated by the Department of Energy, Office of Nuclear Energy, Advanced Materials and Manufacturing Technologies sponsored qualification programs. Future work could extend the tool to other types of material properties and/or expand the demo user interface to make it accessible across the AMMT program.

36 MATERIALS SCIENCE↗

Indirect morphological analysis of particles in polymer particle composites via non-destructive permittivity measurements

We report polymers with specific properties (e.g. electrical, optical or mechanical) are commonly obtained via the addition of additives. The composites final properties rely on the preservation of these additives during embedding, which is, in particular, challenging for high aspect ratio particles, like shear-sensitive flaky particles (ssFP). Thus, in cases of ssFP off- or in-line monitoring is required. This study addresses the lack of suitable non-destructive monitoring methods appropriate for ssFP possessing a thickness below 1um and an area equivalent diameter of several 10 um. An elegant method was developed to validate the integrity of ssFP within composites, which is based on the measurement of the composite's permittivity and applying precise micro-structure property correlations to indirectly determine their morphological features. The main hypothesis tested was that a reduction of the particle’s aspect ratio by a factor of larger than 5 can be detected by the measurement of the composite's permittivity. In this study,the matrix polymer polyethylene or an epoxy resin together with mica-based ssFP with a mean area equivalent diameter of 42 um were used. The micro-structure property correlation presented by G. Ondracek [Z. f. Werkstofftechnik, 8:280-287, 1977] provided the necessary theoretical backbone to indirectly infer geometrical changes to the ssFP from permittivity measurements. An excellent match was obtained between the indirectly and the directly determined particle aspect ratios. This preliminary study established the presented technique as a promising non-destructive test method to monitor the integrity of ssFPs embedded in a polymer. In principle this technique is adaptable for in-line process monitoring.

36 MATERIALS SCIENCE↗

Experimental evaluation of neural probe’s insertion induced injury based on digital image correlation method

Purpose: The application of neural probes in clinic has been challenged by probes’ short lifetime when implanted into brain tissue. The primary goal is to develop an evaluation system for testing brain tissue injury induced by neural probe’s insertion using microscope based digital image correlation method. Methods: A brain tissue phantom made of silicone rubber with speckle pattern on its surface was fabricated. To obtain the optimal speckle pattern, mean intensity gradient parameter was used for quality assessment. The designed testing system consists of three modules: (a) load module for simulating neural electrode implantation process; (b) data acquisition module to capture micrographs of speckle pattern and to obtain reactive forces during the insertion of the probe; (c) postprocessing module for extracting tissue deformation information from the captured speckle patterns. On the basis of the evaluation system, the effects of probe wedge angle, insertion speed, and probe streamline on insertion induced tissue injury were investigated. Results: The optimal quality speckle pattern can be attained by the following fabrication parameters: spin coating rate—1000 r/min, silicone rubber component A: silicone rubber component B: softener: graphite = 5 ml: 5 ml: 2 ml: 0.6 g. The probe wedge angle has a significant effect on tissue injury. Compared to wedge angle 40° and 20°, maximum principal strain of 60° wedge angle was increased by 40.3% and 87.5%, respectively; compared with a relatively higher speed (500 μm/s), the maximum principle strain within the tissue induced by slow insertion speed (100 μm/s) was increased by 14.3%; insertion force required by probe with convex streamline was smaller than the force of traditional probe. Based on the experimental results, a novel neural probe that has a rounded tip covered by a biodegradable silk protein coating with convex streamline was proposed, which has both lower insertion and micromotion induced tissue injury. Conclusions: The established evaluation system has provided a simulation environment for testing brain tissue injury produced by various insertion conditions. At the same time, it eliminates the adverse effect of biological factors on tissue deformation during the experiment, improving the repeatability of measurement results. As a result, the evaluation system will provide support on novel neural probe design that can reduce the acute tissue injury during the implantation of the probe.

61 RADIATION PROTECTION AND DOSIMETRY↗

Identification of Post-necking Tensile Stress–Strain Behavior of Steel Sheet: An Experimental Investigation Using Digital Image Correlation Technique

The stress–strain behavior of sheet metal is commonly evaluated by tensile test. However, the true stress–strain curve is restricted up to uniform elongation of the material. Usually, after the uniform elongation of the material the true stress–strain is obtained by extrapolation. The present work demonstrates a procedure to find out the true tensile stress–strain curve of the steel sheet after necking using digital image correlation (DIC) technique. Hill’s normal anisotropic yield criteria and local strains measured by DIC technique are used to correct the local stress and strain states at the diffuse necked area. The proposed procedure is shown to successfully determine the true tensile stress–strain curve of ferritic and dual-phase steel sheets after necking/uniform elongation.

36 MATERIALS SCIENCE↗

Progress on Nuclear Data Covariances: AFCI-1.2 Covariance Library

Improved neutron cross section covariances were produced for 110 materials including 12 light nuclei (coolants and moderators), 78 structural materials and fission products, and 20 actinides. Improved covariances were organized into AFCI-1.2 covariance library in 33-energy groups, from 10{sup -5} eV to 19.6 MeV. BNL contributed improved covariance data for the following materials: {sup 23}Na and {sup 55}Mn where more detailed evaluation was done; improvements in major structural materials {sup 52}Cr, {sup 56}Fe and {sup 58}Ni; improved estimates for remaining structural materials and fission products; improved covariances for 14 minor actinides, and estimates of mubar covariances for {sup 23}Na and {sup 56}Fe. LANL contributed improved covariance data for {sup 235}U and {sup 239}Pu including prompt neutron fission spectra and completely new evaluation for {sup 240}Pu. New R-matrix evaluation for {sup 16}O including mubar covariances is under completion. BNL assembled the library and performed basic testing using improved procedures including inspection of uncertainty and correlation plots for each material. The AFCI-1.2 library was released to ANL and INL in August 2009.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Coupled Boltzmann transport equations of heavy quarks and quarkonia in quark-gluon plasma

We develop a framework of coupled transport equations for open heavy flavor and quarkonium states, in order to describe their transport inside the quark-gluon plasma. Our framework is capable of studying simultaneously both open and hidden heavy flavor observables in heavy-ion collision experiments and can account for both, uncorrelated and correlated recombination. Our recombination implementation depends on real-time open heavy quark and antiquark distributions. We carry out consistency tests to show how the interplay among open heavy flavor transport, quarkonium dissociation and recombination drives the system to equilibrium. We then apply our framework to study bottomonium production in heavy-ion collisions. We include Υ(1S), Υ(2S), Υ(3S), χb (1P) and χb (2P) in the framework and take feed-down contributions during the hadronic gas stage into account. Cold nuclear matter effects are included by using nuclear parton distribution functions for the initial primordial heavy flavor production. A calibrated 2 + 1 dimensional viscous hydrodynamics is used to describe the bulk QCD medium. We calculate both the nuclear modification factor R AA of all bottomonia states and the azimuthal angular anisotropy coefficient v 2 of the Υ(1S) state and find that our results agree reasonably with experimental measurements. Our calculations indicate that correlated cross-talk recombination is an important production mechanism of bottomonium in current heavy-ion experiments. The importance of correlated recombination can be tested experimentally by measuring the ratio of R AA ( χb (1P)) and R AA (Υ(2S)).

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Boosting H I -Galaxy Cross-Clustering Signal through Higher-Order Cross-Correlations

After reionization, neutral hydrogen (${\rm H\, \small {I}}$) traces the large-scale structure (LSS) of the Universe, enabling ${\rm H\, \small {I}}$ intensity mapping (IM) to capture the LSS in 3D and constrain key cosmological parameters. We present a new framework utilizing higher-order cross-correlations to study ${\rm H\, \small {I}}$ clustering around galaxies, tested using real-space data from the IllustrisTNG300 simulation. This approach computes the joint distributions of k-nearest neighbor (kNN) optical galaxies and the ${\rm H\, \small {I}}$ brightness temperature field smoothed at relevant scales (the kNN-field framework), providing sensitivity to all higher-order cross-correlations, unlike two-point statistics. To simulate ${\rm H\, \small {I}}$ data from actual surveys, we add random thermal noise and apply a simple foreground cleaning model, filtering out Fourier modes of the brightness temperature field with k ∥ < k min,∥ . Under current levels of thermal noise and foreground cleaning, typical of a Canadian Hydrogen Intensity Mapping Experiment (CHIME)-like survey, the ${\rm H\, \small {I}}$-galaxy cross-correlation signal in our simulations, using the kNN-field framework, is detectable at >30σ across r = [3, 12] h –1 Mpc. In contrast, the detectability of the standard two-point correlation function (2PCF) over the same scales depends strongly on the foreground filter: a sharp k ∥ filter can spuriously boost detection to 8σ due to position-space ringing, whereas a less sharp filter yields no detection. Nonetheless, we conclude that kNN-field cross-correlations are robustly detectable across a broad range of foreground filtering and thermal noise conditions, suggesting their potential for enhanced constraining power over 2PCFs.

79 ASTRONOMY AND ASTROPHYSICS↗