Search NASA⌕ Search

SEARCH · Search NASA

Results for “ABRASION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Friction and wear with a single-crystal abrasive grit of silicon carbide in contact with iron base binary alloys in oil: Effects of alloying element and its content

Sliding friction experiments were conducted with various iron-base binary alloys (alloying elements were Ti, Cr, Mn, Ni, Rh, and W) in contact with a rider of 0.025-millimeter-radius, single-crystal silicon carbide in mineral oil. Results indicate that atomic size and content of alloying element play a dominant role in controlling the abrasive-wear and -friction properties of iron-base binary alloys. The coefficient of friction and groove height (wear volume) general alloy decrease, and the contact pressure increases in solute content. There appears to be very good correlation of the solute to iron atomic radius ratio with the decreasing rate of coefficient of friction, the decreasing rate of groove height (wear volume), and the increasing rate of contact pressure with increasing solute content C. Those rates increase as the solute to iron atomic radius ratio increases from unity.

Miyoshi, K.↗
NASA NTRS1981

Abrasive drill for resilient materials

Resilient materials normally present problem in obtaining accurate and uniform hole size and position. Tool is fabricated from stiff metal rod such as tungsten or carbon steel that has diameter slightly smaller than required hole. Piercing/centering point is ground on one end of rod. Rod is then plasma-sprayed (flame-sprayed) with suitable hard abrasive coating. High-speed, slow-feed operation of tool is necessary for accurate holes, and this can be done with drill press, hard drill, or similar machines.

Koch, A. J.↗
NASA NTRS1979

Low-cost, high-efficiency silicon by heat exchanger method and fixed abrasive slicing technique

The paper describes the heat exchanger method (HEM) for growing silicon crystals. The problem of ingot cracking was solved by using a graded structure silica crucible, and vacuum processing eliminated expensive high-purity argon. Solar cells fabricated from HEM silicon demonstrated conversion efficiencies up to 15% (AM1) at low cost, using square cross-section, single crystal silicon. A modified multiblade slurry machine was adapted for multiwire fixed abrasive slicing of silicon which uses a diamond attached to wires; this method provides a conversion ratio of 1.08 sq m of wafer per kg of silicon ingot, and produces wafers free of edge chipping with a surface damage of 3-5 microns.

Khattak, C. P.↗
NASA NTRS1981

Heat sealable, flame and abrasion resistant coated fabric

Flame retardant, abrasion resistant elastomeric compositions are comprised of thermoplastic polyurethane polymer and flame retarding amounts of a filler selected from decabromodiphenyloxide and antimony oxide in a 3:1 weight ratio, and decabromodiphenyloxide, antimony oxide, and ammonium polyphosphate in a 3:1:3 weight ratio respectively. Coated fabrics employing such elastomeric compositions as coating film are flexible, lightweight, and air impermeable and can be made using heat or dielectric sealing procedures.

Tschirch, R. P.↗
NASA NTRS1982

Wire blade development for Fixed Abrasive Slicing Technique (FAST) slicing

A low cost, effective slicing method is essential to make ingot technology viable for photovoltaics in terrestrial applications. The fixed abrasive slicing technique (FAST) combines the advantages of the three commercially developed techniques. In its development stage FAST demonstrated cutting effectiveness of 10 cm and 15 cm diameter workpieces. Wire blade development is still the critical element for commercialization of FAST technology. Both impregnated and electroplated wire blades have been developed; techniques have been developed to fix diamonds only in the cutting edge of the wire. Electroplated wires show the most near term promise and this approach is emphasized. With plated wires it has been possible to control the size and shape of the electroplating, it is expected that this feature reduces kerf and prolongs the life of the wirepack.

Khattak, C. P.↗
NASA NTRS1982

Overview of a new slicing method: Fixed Abrasive Slicing Technique (FAST)

The fixed abrasive slicing technique (FAST) was developed to slice silicon ingots more effectively. It was demonstrated that 25 wafers/cm can be sliced from 10 cm diameter and 19 wafers/cm from 15 cm diameter ingots. This was achieved with a combination of machine development and wire-blade development programs. Correlation was established between cutting effectiveness and high surface speeds. A high speed slicer was designed and fabricated for FAST slicing. Wirepack life of slicing three 10 cm diameter ingots was established. Electroforming techniques were developed to control widths and prolong life of wire-blades. Economic analysis indicates that the projected add-on price of FAST slicing is compatible with the DOE price allocation to meet the 1986 cost goals.

Schmid, F.↗
NASA NTRS1982

Tribological properties of amorphous alloys and the role of surfaces in abrasive wear of materials

The research approach undertaken by the authors relative to the subject, and examples of results from the authors are reviewed. The studies include programs in adhesion, friction, and various wear mechanisms (adhesive and abrasive wear). The materials which have been studied include such ceramic and metallic materials as silicon carbide, ferrites, diamond, and amorphous alloys.

Miyoshi, K.↗
NASA NTRS1982

Improvements to the Langley HZE abrasion model

Improvements to a previously developed high charge energy abrasion model are made by incorporating more realistic values for the constituent Fermi momentum and nucleon root-mean-square charge radius. The theoretical predictions for neon projectiles at 2.1 GeV/nucleon colliding with carbon and molybdenum targets are in excellent agreement with recent experiment results.

Townsend, L. W.↗
NASA NTRS1982

Study of abrasive wear rate of silicon using n-alcohols

The work carried out at the University of Illinois at Chicago for the Flat-Plate Solar Array Project under contract No. 956053 is summarized. The abrasion wear rate of silicon in a number of fluid environments and the parameters that influence the surface mechanical properties of silicon were determined. Three tests were carried out in this study: circular and linear multiple-scratch test, microhardness test and a three-point bend test. The pertinent parameters such as effect of surface orientation, dopant and fluid properties were sorted. A brief review and critique of previous work is presented.

Danyluk, S.↗
NASA NTRS1982

Part 2: Multi-wire slicing. Fixed Abrasive Slicing Technique (FAST)

The Fixed Abrasive Slicing Techniques (FAST) is a new slicing technique that was developed to slice ingots more effectively. It was demonstrated that 25 wafers/cm can be sliced from 10cm diameter and 19 wafers/cm from 15 cm diameter ingots. Over 99% yield (222 out of a possible 224) was demonstrated during slicing of a 10 cm diameter ingots at 25 wafers/cm. The average thickness of wafers was 0.249 mm and the kerf was 0.151 mm. Slicing rates as high as 0.14 mm/min were also demonstrated for 10 cm diameter ingots.

Source record↗
NASA NTRS1982

Silicon slicing by fixed abrasive slicing technique

One of the major cost factors in silicon ingot technology adaptation for terrestrial photovoltaic application is in slicing boules into wafers. The most developed industrial practice is the Internal Diameter (ID) slicing. This method utilizes diamond cutting. The diamond stands up for long periods, hence, the cost of expendable materials is low. However, the ID technology as practiced today has poor material utilization. The Multiblade Slurry (MBS) method has low equipment and labor costs but its expendable material costs are high. Recently Multiwire Slurry (MWS) technology has shown very good material utilization, but its expendable material costs are even higher than MBS. The multiwire Fixed Abrasive Slicing Technique (FAST) still in advanced development stage, combines the low expendable material costs of ID method, the low labor and equipment costs of MBS and high material utilization of MWS.

Schmid, F.↗
NASA NTRS1982

Recent developments in multi-wire fixed abrasive slicing technique (FAST)

Slicing is an important processing step for all technologies based on the use of ingots. A comparison of the economics of three slicing techniques shows that the fixed abrasive slicing technique (FAST) is superior to the internal diameter (ID) and the multiblade slurry (MBS) techniques. Factors affecting contact length are discussed, taking into account kerf width, rocking angle, ingot size, and surface speed. Aspects of blade development are also considered. A high concentration of diamonds on wire has been obtained in wire packs usd for FAST slicing. The material removal rate was found to be directly proportional to the pressure at the diamond tips.

Schmid, F.↗
NASA NTRS1983

Heat sealable, flame and abrasion resistant coated fabric

Flame retardant, abrasion resistant elastomeric compositions are disclosed which are comprised of thermoplastic polyurethane polymer and flame retarding amounts of a filler selected from decabromodiphenyloxide and antimony oxide in a 3:1 weight ratio, and decabromodiphenyloxide, antimony oxide, and ammonium polyphosphate in a 3:1:3 weight ratio respectively. Heat sealable coated fabrics employing such elastomeric compositions as coating film are produced by dissolving the elastomeric composition to form a solution, casting the solution onto a release paper and drying it to form an elastomeric film. The film is then bonded to a woven, knitted, or felted fabric.

Tschirch, R. P.↗
NASA NTRS1986

Abrasion-Resistant Coating for Flexible Insulation

Ceramic coating increases durability and heat resistance of flexible high-temperature insulation. Coating compatible with quartz-fabric insulation allowing it to remain flexible during and after repeated exposures to temperatures of 1,800 degree F (982 degree C). Prevents fabric from becoming brittle while increasing resistance to aerodynamic abrasion and loading. Coating consists of penetrating precoat and topcoat. Major ingredients high-purity colloidal silica binder and ground silica filler, which ensure stability and compatibility with fabric at high temperatures. Both precoat and topcoat cured at room temperature.

Mui, D.↗
NASA NTRS1985

Abrasion behavior of aluminum and composite skin coupons, stiffened skins and stiffened panels representative of transport airplane structures

A three-phase investigation was conducted to compare the friction and wear response of aluminum and graphite-epoxy composite materials when subjected to loading conditions similar to those experienced by the skin panels on the underside of a transport airplane during an emergency belly landing on a runway surface. The first phase involved a laboratory test which used a standard belt sander to provide the sliding abrasive surface. Small skin-coupon test specimens were abraded over a range of pressures and velocities to determine the effects of these variables on the coefficient of friction and wear rate. The second phase involved abrading I-beam stiffened skins on actual runway surface over the same range of pressures and velocities used in the first phase. In the third phase, large stiffened panels which most closely resembled transport fuelage skin construction were abraded on a runway surface. This report presents results from each phase of the investigation and shows comparisons between the friction and wear behavior of the aluminum and graphite-epoxy composite materials.

Jackson, K. E.↗
NASA NTRS1998

Mars Pathfinder Wheel Abrasion Experiment Ground Test

The National Aeronautics and Space Administration (NASA) sent a mission to the martian surface, called Mars Pathfinder. The mission payload consisted of a lander and a rover. The primary purpose of the mission was demonstrating a novel entry, descent, and landing method that included a heat shield, a parachute, rockets, and a cocoon of giant air bags. Once on the surface, the spacecraft returned temperature measurements near the Martian surface, atmosphere pressure, wind speed measurements, and images from the lander and rover. The rover obtained 16 elemental measurements of rocks and soils, performed soil-mechanics, atmospheric sedimentation measurements, and soil abrasiveness measurements.

Keith, Theo G., Jr.↗
NASA NTRS2004

Monitoring and Testing the Parts Cleaning Stations, Abrasive Blasting Cabinets, and Paint Booths

I have the opportunity to work in the Environmental Management Office (EMO) this summer. One of the EMO's tasks is to make sure the Environmental Management System is implemented to the entire Glenn Research Center (GRC). The Environmental Management System (EMS) is a policy or plan that is oriented toward minimizing an organization's impact to the environment. Our EMS includes the reduction of solid waste regeneration and the reduction of hazardous material use, waste, and pollution. With the Waste Management Team's (WMT) help, the EMS can be implemented throughout the NASA Glenn Research Center. The WMT is responsible for the disposal and managing of waste throughout the GRC. They are also responsible for the management of all chemical waste in the facility. My responsibility is to support the waste management team by performing an inventory on parts cleaning stations, abrasive cabinets, and paint booths through out the entire facility. These booths/stations are used throughout the center and they need to be monitored and tested for hazardous waste and material. My job is to visit each of these booths/stations, take samples of the waste, and analyze the samples.

Jordan, Tracee M.↗