Search NASA⌕ Search

SEARCH · Search NASA

Results for “ALS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Effect of Mn on eutectic phase equilibria in Al-rich Al-Ce-Ni alloys

Microstructural analysis of additively manufactured (AM) Al-Ce-Ni-Mn alloys has identified phases not predicted from existing ternary liquidus projections in the Al-Ce-Ni system. Because the rapid cooling rate of AM is orders of magnitude above that of traditional casting, it is unclear if these additional phases arose from the non-equilibrium processing conditions of AM, a drastic shift in phase stability in the system due to the addition of 1 wt% Mn, or some combination of these two influences. The phases and microstructure of cast samples of Al-Ce-Ni and Al-Ce-Ni-Mn alloys were characterized for several annealing conditions which revealed the equilibrium phases at different temperatures. Phase analysis confirmed that minute levels of Mn substituted for Ni in the system drastically shifts the liquidus projection in the Al-rich corner of the ternary phase diagram such that the eutectic Al 3 Ni phase is suppressed in favor of the Al 23 Ni 6 (Ce,Mn) 4 phase. Further addition of Mn promotes the formation of Al 20 Mn 2 Ce and Al 10 Mn 2 Ce phases. The phase analysis data was then used to improve the CALPHAD modeling of the liquidus projection and isothermal sections for the Al-rich Al-Ce-Ni-Mn quaternary system. Thermodynamic modeling and experimental analysis on phases in the AM sample of Al-Ce-Ni with Mn confirmed that the phases present are consistent with Mn-containing Al-Ce-Ni cast samples. Here, this investigation demonstrates the potential for using secondary alloying elements to drastically alter phase stability and microstructure in alloy systems.

36 MATERIALS SCIENCE↗

IMPACT OF A REVISED {sup 25}Mg(p, {gamma}){sup 26}Al REACTION RATE ON THE OPERATION OF THE Mg-Al CYCLE

Proton captures on Mg isotopes play an important role in the Mg-Al cycle active in stellar H-burning regions. In particular, low-energy nuclear resonances in the {sup 25}Mg(p, {gamma}){sup 26}Al reaction affect the production of radioactive {sup 26}Al{sup gs} as well as the resulting Mg/Al abundance ratio. Reliable estimations of these quantities require precise measurements of the strengths of low-energy resonances. Based on a new experimental study performed at the Laboratory for Underground Nuclear Astrophysics, we provide revised rates of the {sup 25}Mg(p, {gamma}){sup 26}Al{sup gs} and the {sup 25}Mg(p, {gamma}){sup 26}Al {sup m} reactions with corresponding uncertainties. In the temperature range 50-150 MK, the new recommended rate of {sup 26}Al {sup m} production is up to five times higher than previously assumed. In addition, at T = 100 MK, the revised total reaction rate is a factor of two higher. Note that this is the range of temperature at which the Mg-Al cycle operates in a H-burning zone. The effects of this revision are discussed. Due to the significantly larger {sup 25}Mg(p, {gamma}){sup 26}Al {sup m} rate, the estimated production of {sup 26}Al{sup gs} in H-burning regions is less efficient than previously obtained. As a result, the new rates should imply a smaller contribution from Wolf-Rayet stars to the galactic {sup 26}Al budget. Similarly, we show that the asymptotic giant branch (AGB) extra-mixing scenario does not appear able to explain the most extreme values of {sup 26}Al/{sup 27}Al, i.e., >10{sup -2}, found in some O-rich presolar grains. Finally, the substantial increase of the total reaction rate makes the hypothesis of self-pollution by massive AGBs a more robust explanation for the Mg-Al anticorrelation observed in globular-cluster stars.

79 ASTRONOMY AND ASTROPHYSICS↗

Interdiffusion in Diffusion Couples: U-Mo v. Al and Al-Si

Interdiffusion and microstructural development in the U-Mo-Al system was examined using solid-tosolid diffusion couples consisting of U-7wt.%Mo, U-10wt.%Mo and U-12wt.%Mo vs. pure Al, annealed at 600°C for 24 hours. The influence of Si alloying addition (up to 5 wt.%) in Al on the interdiffusion microstructural development was also examined using solid-to-solid diffusion couples consisting of U-7wt.%Mo, U-10wt.%Mo and U-12wt.%Mo vs. pure Al, Al-2wt.%Si, and Al-5wt.%Si annealed at 550°C up to 20 hours. Scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron probe microanalysis (EPMA) were employed to examine the development of a very fine multiphase intermetallic layer. In ternary U-Mo-Al diffusion couples annealed at 600°C for 24 hours, interdiffusion microstructure varied of finely dispersed UAl3, UAl4, U6Mo4Al43, and UMo2Al20 phases while the average composition throughout the interdiffusion zone remained constant at approximately 80 at.% Al. Interdiffusion microstructure observed by SEM/TEM analyses and diffusion paths drawn from concentration profiles determined by EPMA appear to deviate from the assumption of “local thermodynamic equilibrium,” and suggest that interdiffusion occurs via supersaturated UAl4 followed by equilibrium transformation into UAl3, U6Mo4Al43, UAl4 and UMo2Al20 phases. Similar observation was made for U-Mo vs. Al diffusion couples annealed at 550°C. The addition of Si (up to 5 wt.%) in Al significantly reduced the thickness of the intermetallic layer by changing the constituent phases of the interdiffusion zone developed in U-Mo vs. Al-Si diffusion couples. Specifically, the formation of (U,Mo)(Al,Si)3 with relatively large solubility for Mo and Si, along with UMo2Al20 phases was observed along with disappearance of U6Mo4Al43 and UAl4 phases. Simplified understanding based on U-Al, U-Si, and Mo-Si binary phase diagrams is discussed in the light of the beneficial effect of Si alloying addition.

99 GENERAL AND MISCELLANEOUS↗

Formation Mechanism of Nanoscale Al{sub 3}Fe Phase in Al-Fe Alloy During Semisolid Forming Process

The formation mechanism of nanoscale Al{sub 3}Fe phase in Al-1Fe (wt pct) alloy during rheo-extrusion was investigated, and the mechanical property of the prepared alloy was also measured. The results show that the average length of Al{sub 3}Fe phase in Al-1Fe alloy prepared by rheo-extrusion is 300 nm, which is much more refined than the needlelike Al{sub 3}Fe phase in as-cast Al-1Fe alloy (50 μm). In rheo-extrusion, Al{sub 3}Fe phase formed by eutectic reaction is bonelike, but it could be continuously refined by the shear deformation in the wheel groove, in equal channel angular flow, and in expansion extrusion mold. The total equivalent strain of the shear deformation is higher than 4.82. The tensile strength and elongation of Al-1Fe alloy prepared by rheo-extrusion are 135 MPa and 30 pct, respectively. The tensile strength of Al-1Fe alloy prepared by rheo-extrusion is 58.8 pct higher than that of as-cast Al-1Fe alloy, and the elongation is 19 pct higher than that of as-cast Al-1Fe alloy. Compared with as-cast Al-1Fe alloy, the improvements of tensile strength and elongation caused by shear deformation in rheo-extrusion are higher than the reported improvements induced by rare earth modification.

36 MATERIALS SCIENCE↗

WO x supported on γ-Al 2 O 3 with different morphologies as model catalysts for alkanol dehydration

The distinctive morphological and surface characteristics of platelet-like γ-Al2O3 were compared to a regular, commercial γ-Al2O3. γ-Al2O3 platelets display dominant (110) surface facets and higher densities of coordinative unsaturated penta-coordinate Al3+ (Al3+penta) sites than regular γ-Al2O3, as measured by solid-state magic-angle spinning nuclear magnetic resonance spectroscopy (MAS NMR). Such Al3+penta sites are also the preferred surface anchoring sites for tungsten oxide (WOx) species consistent with NMR analysis indicating that these sites are consumed upon WOx adsorption. The higher Al3+penta density on γ-Al2O3 platelets leads to greater WOx dispersion (or smaller WOx clusters), as demonstrated by scanning transmission electron microscopy and ultraviolet–visible spectroscopy, and WOx species at intermediate WOx surface concentration are the most active for the probe reaction of 2-butanol dehydration. WOx on γ-Al2O3 platelets approaches the highest turnover rates at higher surface densities than WOx on regular γ-Al2O3, yet with similar highest rate values for both series of catalysts. This indicates that different Al2O3 supports mainly affect the dispersion of supported WOx rather than the intrinsic reactivity of individual WOx clusters with similar size.

Environmental Molecular Sciences Laboratory↗

Phase Constituents of Al-rich U-Mo-Al Alloys Examined by Transmission Electron Microscopy

To supplement the understanding of diffusional interactions involving Al-rich region of the U-Mo-Al system, alloys with composition 85.7Al-11.44U-2.86Mo and 87.5Al-10U-2.5Mo in at.%, were examined to determine the equilibrium phase constituents at 500?C. These alloys were triple arc-melted, homogenized at 500?C for 200 hours, and water-quenched to preserve the high temperature microstructure. X-ray diffraction, scanning electron microscopy (SEM) with energy dispersive x-ray spectroscopy (XEDS), and transmission electron microscopy (TEM) with high angle annular dark field (HAADF) imaging via scanning transmission electron microscopy (STEM) were employed for the characterization. Alloy specimens for TEM/STEM were prepared using site-specific focused ion beam (FIB) in-situ lift-out (INLO) technique. Despite the homogenization time and temperature, five different phases, namely fcc-Al solid solution, cubic-UAl3, orthorhombic-UAl4, hexagonal-U6Mo4Al43 and diamond cubic-UMo2Al20, were observed. Based on U-Al, U-Mo and Al-Mo binary phase diagrams, previously proposed U-Mo-Al isotherms, and the solidification microstructure of these alloys, the Al-rich region of the equilibrium ternary isotherm at 500?C was constructed. The fcc-Al solid solution, orthorhombic-UAl4, and diamond cubic-UMo2Al20, which were determined to be the equilibrium phases in 85.7Al-11.44U-2.86Mo and 87.5Al-10U-2.5Mo alloys.

99 GENERAL AND MISCELLANEOUS↗

Synthesis and structural characterization of Al{sub 7}C{sub 3}N{sub 3}-homeotypic aluminum silicon oxycarbonitride, (Al{sub 7-x}Si{sub x})(O{sub y}C{sub z}N{sub 6-y-z}) (x{approx}1.2, y{approx}1.0 and z{approx}3.5)

A new aluminum silicon oxycarbonitride, (Al{sub 5.8}Si{sub 1.2})(O{sub 1.0}C{sub 3.5}N{sub 1.5}), has been synthesized and characterized by X-ray powder diffraction (XRPD), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX) and electron energy loss spectroscopy (EELS). The title compound is hexagonal with space group P6{sub 3}/mmc and unit-cell dimensions a=0.322508(4) nm, c=3.17193(4) nm and V=0.285717(6) nm{sup 3}. The atom ratios of Al:Si and those of O:C:N were, respectively, determined by EDX and EELS. The initial structural model was successfully derived from the XRPD data by the direct methods and further refined by the Rietveld method. The crystal is most probably composed of four types of domains with nearly the same fraction, each of which is isotypic to Al{sub 7}C{sub 3}N{sub 3} with space group P6{sub 3}mc. The existence of another new oxycarbonitride (Al{sub 6.6}Si{sub 1.4})(O{sub 0.7}C{sub 4.3}N{sub 2.0}), which must be homeotypic to Al{sub 8}C{sub 3}N{sub 4}, has been also demonstrated by XRPD and TEM. - Graphical abstract: A new oxycarbonitride discovered in the Al-Si-O-C-N system, (Al{sub 7-x}Si{sub x})(O{sub y}C{sub z}N{sub 6-y-z}) (x{approx}1.2, y{approx}1.0 and z{approx}3.5). The crystal is composed of four types of domains (I, II, III and IV), and hence the structure is represented by a split-atom model. Individual crystal structures can be regarded as layered structures, which consist of A-type [(Al, Si){sub 4}(O, C, N){sub 4}] unit layers and B-type [(Al, Si)(O, C, N){sub 2}] single layers. Highlights: > (Al{sub 5.8}Si{sub 1.2})(O{sub 1.0}C{sub 3.5}N{sub 1.5}) as a new aluminum silicon oxycarbonitride. > Crystal structure is determined and represented by a split-atom model. > Existence of another new oxycarbonitride (Al{sub 6.6}Si{sub 1.4})(O{sub 0.7}C{sub 4.3}N{sub 2.0}) is demonstrated. > Both new materials are formed by oxidation and nitridation of (Al, Si){sub 6}(O, C){sub 5}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Substitution studies of Mn and Fe in Ln{sub 6}W{sub 4}Al{sub 43} (Ln=Gd, Yb) and the structure of Yb{sub 6}Ti{sub 4}Al{sub 43}

The synthesis and characterization of Mn- and Fe-substituted Ln{sub 6}W{sub 4}Al{sub 43} (Ln=Gd, Yb) and Yb{sub 6}Ti{sub 4}Al{sub 43} are reported. The compounds adopt the Ho{sub 6}Mo{sub 4}Al{sub 43} structure type with lattice parameters of a∼11 Å and c∼17.8 Å with structural site preferences for Mn and Fe. The magnetization of Yb{sub 6}W{sub 4}Al{sub 43} is sensitive to Mn and Fe doping, which is evident by an increase in the field dependent magnetization. Gd{sub 6}W{sub 4}Al{sub 43}, Gd{sub 6}W{sub 4}Al{sub 42.31(11)}Mn{sub 0.69(11)}, and Gd{sub 6}W{sub 4}Al{sub 41.69(12)}Fe{sub 1.30(12)} order antiferromagnetically in the ab- and c-directions at 15, 14, and 13 K, respectively, with positive Weiss constants, suggesting the presence of ferromagnetic exchange interactions. Anisotropic magnetization data of Gd{sub 6}W{sub 4}Al{sub 43−y}T{sub y} (T=Mn, Fe) analogs are discussed. - Graphical abstract: The magnetic susceptibility of Ln{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} (Ln = Gd, Yb; T= Mn, Fe). Display Omitted - Highlights: • Single crystals of Ln{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} were grown with Al-flux. • Anisotropic magnetic behavior were determined on single crystals. • Gd{sub 6}W{sub 4−x}Al{sub 43−y}T{sub x+y} (T=Mn, Fe) analogs order antiferromagnetically.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fabrication of Al{sub 2}O{sub 3}-20 vol.% Al nanocomposite powders using high energy milling and their sinterability

Highlights: Black-Right-Pointing-Pointer Al{sub 2}O{sub 3}/Al nanocomposite powders were prepared via high energy ball milling. After 20 h milling, the size of Al{sub 2}O{sub 3}-20 vol.% Al nanocomposite particles was in the range of 23-29 nm. A uniform distribution of nanosized Al reinforcement throughout the Al{sub 2}O{sub 3} matrix, coating the particles was successfully obtained. Black-Right-Pointing-Pointer There was no any sign of phase changes during the milling. A competition between the cold welding mechanism and the fracturing mechanism were found during milling and finally the above two mechanisms reached an equilibrium. Black-Right-Pointing-Pointer The highest value of relative density was obtained for the sintered bodies at 1500 Degree-Sign C. Black-Right-Pointing-Pointer The harness of the sintered composite was decreased while the fracture toughness was improved after addition Al into alumina. -- Abstract: In this study, alumina-based matrix nanocomposite powders reinforced with Al particles were fabricated and investigated. The sinterability of the prepared nanocomposite powder at different firing temperature was also conducted. Their mechanical properties in terms of hardness and toughness were tested. Alumina and aluminum powder mixtures were milled in a planetary ball mill for various times up to 30 h in order to produce Al{sub 2}O{sub 3}-20% Al nanocomposite. The phase composition, morphological and microstructural changes during mechanical milling of the nanocomposite particles were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM) techniques, respectively. The crystallite size and internal strain were evaluated by XRD patterns using Scherrer methods. A uniform distribution of the Al reinforcement in the Al{sub 2}O{sub 3} matrix was successfully obtained after milling the powders. The results revealed that there was no any sign of phase changes during the milling. The crystal size decreased with the prolongation of milling times, while the internal strain increased. A simple model is presented to illustrate the mechanical alloying of a ductile-brittle component system. A competition between the cold welding mechanism and the fracturing mechanism were found during powder milling and finally the above two mechanisms reached an equilibrium. The maximum relative density was obtained at 1500 Degree-Sign C. The harness of the sintered composite was decreased while the fracture toughness was improved after addition Al into alumina.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Phase transformations, microstructural refinement and defect evolution mechanisms in Al-Si alloys under non-hydrostatic diamond anvil cell compression

Non-hydrostatic compression of materials using a diamond anvil cell (DAC) can transform equilibrium microstructure of an alloy to novel, potentially metastable states. In this study, in situ synchrotron X-ray diffraction (XRD) during compression up to 24 GPa and subsequent ex situ, high resolution analytical electron microscopy (AEM) after decompression of an Al-Si alloy provided insight into the crystallographic changes during the compression as well as microstructural refinement, and defect structures caused by such a high pressure compression-decompression process. Pressure resolved in-situ synchrotron XRD was used to detail the phase transformation pathway of the eutectic Si phase in Al-Si alloy, from Si-I → Si-XI → Si-V during compression, and a final transformation predominantly to Si-III after decompression. Using scanning and transmission electron microscopy (S/TEM), site specific analysis of the alloy immediately underneath the anvil contact surface demonstrated a highly complex microstructure. A narrow region of thick amorphous Al oxide interspersed with nanocrystalline grains was found at the top surface. Underneath this Al oxide, while the majority the eutectic Si was transformed into highly-deformed, polycrystalline (PC) Si-III, a complex intermediate layer was discovered at the interface between Al and Si, comprised of a small fraction of Al nanocrystals and a majority of nanocrystalline Si-I. This combination of pressure resolved in-situ synchrotron XRD coupled with subsequent high resolution, electron microscopy resolved the phase transformation as well as non-equilibrium microstructures in a metallic alloy induced by a non-hydrostatic high pressure compression followed by decompression.

36 MATERIALS SCIENCE↗

Electron microscopy characterization of an as-fabricated research reactor fuel plate comprised of U-7Mo particles dispersed in an Al-2Si alloy matrix

To understand the microstructural development of nuclear fuel plates during irradiation, it is imperative to know the microstructure of a fuel plate after all the fabrication steps have been completed and before it is inserted into the reactor. To this end, a U-7 wt.% Mo alloy research reactor dispersion fuel plate with Al-2 wt.% Si matrix was destructively examined using scanning and transmission electron microscopy to characterize the developed microstructure after fabrication. Of particular interest for this study was how the Si that was added to the fuel matrix partitioned between the various fuel plate phases during fabrication. Si was added to the matrix so that the microstructure that developed during fuel fabrication would exhibit good irradiation behavior. SEM analysis was used to identify the representative microstructure, the compositions of the various phases, and the partitioning behavior of the fuel and matrix constituents. TEM analysis was employed to definitively identify the phases in the U-7Mo alloy and the phases that formed due to diffusional interactions between the fuel particles and matrix during fuel plate fabrication. The TEM results are the first reported for an as-fabricated U-7 wt.% Mo dispersion fuel plate with an Al alloy matrix. SEM results showed that a significant portion of the original {gamma}-(U-Mo) fuel particles had transformed to a lamellar microstructure, comprised of {alpha}-U and either {gamma} or {gamma}' phases, and the fuel/matrix interaction layers were enriched in Si. TEM analysis identified an ordered fcc (U-Mo)(Al-Si){sub 3} type of phase, which formed at the decomposed U-7Mo/matrix interface and extended into the lamellar microstructure. Some regions of the U-7Mo particles retained the single-phase {gamma}-(U-Mo). Small precipitate phases were observed in the fuel meat matrix that contained Fe, Al, and Si. The Si that is added to the matrix of a U-Mo dispersion fuel plate to improve irradiation performance appears to result in the creation of a Si-rich (U-Mo)(Al-Si){sub 3} type of fuel/matrix interaction layer during fabrication that appears to exhibit favorable behavior during irradiation compared to the behavior of the layers that form in U-Mo dispersion fuel plates without Si in the matrix. - Research Highlights: {yields}Si seems to positively affect the microstructure of an as-fabricated fuel plate. {yields}Si modifications to the fuel plate exhibit favorable performance during irradiation. {yields}Si interdiffuses faster than Al.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

27 Al NMR diffusometry of Al 13 Keggin nanoclusters

Although nanometer-sized aluminum hydroxide clusters (i.e., ϵ-Al 13 , [Al 13 O 4 (OH) 24 (H 2 O) 12 ] 7+ ) command a central role in aluminum ion speciation and transformations between minerals, measurement of their translational diffusion is often limited to indirect methods. Here, in this work, 27 Al pulsed field gradient stimulated echo nuclear magnetic resonance (PFGSTE NMR) spectroscopy has been applied to the AlO 4 core of the ϵ-Al 13 cluster with complementary theoretical simulations of the diffusion coefficient and corresponding hydrodynamic radii from a boundary element-based calculation. The tetrahedral AlO 4 center of the ϵ-Al 13 cluster is symmetric and exhibits only weak quadrupolar coupling, which results in favorable T 1 and T 2 27 Al NMR relaxation coefficients for 27 Al PFGSTE NMR studies. Stokes–Einstein relationship was used to relate the 27 Al diffusion coefficient of the ϵ-Al 13 cluster to the hydrodynamic radius for comparison with theoretical simulations, dynamic light scattering from literature, and previously published 1 H PFGSTE NMR studies of chelated Keggin clusters. This first-of-its-kind observation proves that 27 Al PFGSTE NMR diffusometry can probe symmetric Al environments in polynuclear clusters of greater molecular weight than previously considered.

27Al↗

From irregular to regular eutectic growth in the Al-Al 3 Ni system: In situ observations during directional solidification

Here we investigate the irregular eutectic growth dynamics of the Al-Al 3 Ni alloy, in which one of the solid phases (Al 3 Ni) grows faceted from the liquid. Leveraging in situ optical microscopy and synchrotron transmission x-ray microscopy, we address the question of the degree of coupling between Al and Al 3 Ni at the growth front and that of the shape of the microstructures left behind in the bulk solid during directional solidification. Real-time optical observations bring evidence for a morphological transition from a eutectic-grain dependent, irregular eutectic growth at low solidification velocity V (typically 1 μm s -1 ), to a weakly anisotropic, regular growth at higher V ( reaching 10 μm s -1 ). Unprecedented x-ray nano-imaging of the solid–liquid interface, and 3D characterization of the growth patterns, were made possible by a new DS setup at Brookhaven National Laboratory’s NSLS-II. At low V, the leading tips of partly faceted Al 3 Ni crystals are observed to grow not far ahead of the Al growth front. Correlating in situ images and postmortem 3D tomographic reconstructions reveals that the presence of faceted and non-faceted regions of Al 3 Ni crystals in the solid is a direct consequence of coupling and decoupling during DS, respectively. Upon increasing V, the lead distance of Al 3 Ni vanishes, and the shape of Al 3 Ni ceases to be governed by faceted growth. These observations cast light onto the basic mechanisms (faceted growth, diffusive coupling, and the dynamics of trijunctions) governing a faceted to rod-like transition upon increasing V in the Al 3 Ni system, with broad implications to a large class of irregular eutectics.

36 MATERIALS SCIENCE↗

Phase stability in cast and additively manufactured Al-rich Al-Cu-Ce alloys

Additively manufactured (AM) eutectic Al alloy systems have been studied extensively for advantageous thermal stability and mechanical properties due to their refined microstructures. Al-Cu-Ce alloys are one subset of these AM eutectic alloys. Here we studied phase stability in AM Al-Cu-Ce alloys and compared it to that of conventionally cast ones. A new phase, Al 8 Cu 3 Ce, was identified in the microstructures of both AM and cast Al-Cu-Ce alloys. This Al 8 Cu 3 Ce phase was not previously included on experimental or thermodynamically calculated phase diagrams of the Al-Cu-Ce system. Therefore, we performed additional thermodynamic modeling of the system. These models were experimentally validated with cast and subsequently heat-treated Al-Cu-Ce alloys. We found that despite the refined microstructure of the AM alloys, the phases formed were consistent with the cast alloys, suggesting that AM processing did not significantly alter the formation and stability of phases from that in the conventional alloys. In conclusion, this work has resolved inconsistent previous descriptions of the Al-Cu-Ce ternary phase diagram in the Al-rich region and resulted in the addition of the Al 8 Cu 3 Ce as an equilibrium phase above 500 °C.

36 MATERIALS SCIENCE↗

Determination of the vacancy distribution over Al cation sites in γ-Al 2 O 3

Although gamma-alumina (γ-Al 2 O 3 ) is an extensively used material with wide-ranging applications due to its inherently high surface area and acidity, its atomic structure is still not fully understood. γ-Al 2 O 3 is described as having a spinel-like structure, where the O sublattice has a face-centered cubic (FCC) arrangement and Al cations are placed in the spinel tetrahedral and octahedral interstitial sites. Achieving the correct stoichiometry of Al 2 O 3 , however, requires the introduction of Al vacancies into some of the interstitial sites. Despite the importance of accurately describing the structure of γ-Al 2 O 3 , the distribution of vacancies between tetrahedral and octahedral sites remains unclear, in part because of the usually poor crystalline quality of γ-Al 2 O 3 that has often been used in previous studies. To determine the actual cation distribution in γ-Al 2 O 3 , single-crystalline γ-Al 2 O 3 was investigated using a correlative approach of experimental and simulated selected-area electron diffraction (SAED) and high-resolution electron energy-loss spectroscopy (EELS). Comparison of the reflection intensities in single-crystal SAED to simulated SAED from models with varied vacancy distributions revealed that vacancies exist primarily on tetrahedral sites, contrary to the placement of vacancies on octahedral sites proposed in several common models. Comparison of EELS spectra—acquired with the highest energy resolution reported so far for γ-Al 2 O 3 —with ab initio multiple scattering EELS simulations confirmed the distribution of vacancies on tetrahedral sites. These results enable more accurate modeling of γ-Al 2 O 3 to better predict its properties in existing and future applications.

36 MATERIALS SCIENCE↗

EARLY SOLAR NEBULA CONDENSATES WITH CANONICAL, NOT SUPRACANONICAL, INITIAL {sup 26}Al/{sup 27}Al RATIOS

The short-lived radionuclide {sup 26}Al existed throughout the solar nebula 4.57 Ga ago, and the initial abundance ratio ({sup 26}Al/{sup 27}Al){sub 0}, as inferred from magnesium isotopic compositions of calcium-aluminum-rich inclusions (CAIs) in chondritic meteorites, has become a benchmark for understanding early solar system chronology. Internal mineral isochrons in most CAIs measured by secondary ion mass spectrometry (SIMS) give ({sup 26}Al/{sup 27}Al){sub 0} {approx} (4-5) x 10{sup -5}, called 'canonical'. Some recent high-precision analyses of (1) bulk CAIs measured by multicollector inductively coupled plasma mass spectrometry (MC-ICPMS), (2) individual CAI minerals and their mixtures measured by laser-ablation MC-ICPMS, and (3) internal isochrons measured by multicollector (MC)-SIMS indicated a somewhat higher 'supracanonical' ({sup 26}Al/{sup 27}Al){sub 0} ranging from (5.85 {+-} 0.05) x 10{sup -5} to >7 x 10{sup -5}. These measurements were done on coarse-grained Type B and Type A CAIs that probably formed by recrystallization and/or melting of fine-grained condensate precursors. Thus the supracanonical ratios might record an earlier event, the actual nebular condensation of the CAI precursors. We tested this idea by performing in situ high-precision magnesium isotope measurements of individual minerals in a fine-grained CAI whose structures and volatility-fractionated trace element abundances mark it as a primary solar nebula condensate. Such CAIs are ideal candidates for the fine-grained precursors to the coarse-grained CAIs, and thus should best preserve a supracanonical ratio. Yet, our measured internal isochron yields ({sup 26}Al/{sup 27}Al){sub 0} = (5.27 {+-} 0.17) x 10{sup -5}. Thus our data do not support the existence of supracanonical ({sup 26}Al/{sup 27}Al){sub 0} = (5.85-7) x 10{sup -5}. There may not have been a significant time interval between condensation of the CAI precursors and their subsequent melting into coarse-grained CAIs.

79 ASTRONOMY AND ASTROPHYSICS↗

Self-forming Al oxide barrier for nanoscale Cu interconnects created by hybrid atomic layer deposition of Cu–Al alloy

The authors synthesized a Cu–Al alloy by employing alternating atomic layer deposition (ALD) surface reactions using Cu and Al precursors, respectively. By alternating between these two ALD surface chemistries, the authors fabricated ALD Cu–Al alloy. Cu was deposited using bis(1-dimethylamino-2-methyl-2-butoxy) copper as a precursor and H{sub 2} plasma, while Al was deposited using trimethylaluminum as the precursor and H{sub 2} plasma. The Al atomic percent in the Cu–Al alloy films varied from 0 to 15.6 at. %. Transmission electron microscopy revealed that a uniform Al-based interlayer self-formed at the interface after annealing. To evaluate the barrier properties of the Al-based interlayer and adhesion between the Cu–Al alloy film and SiO{sub 2} dielectric, thermal stability and peel-off adhesion tests were performed, respectively. The Al-based interlayer showed similar thermal stability and adhesion to the reference Mn-based interlayer. Our results indicate that Cu–Al alloys formed by alternating ALD are suitable seed layer materials for Cu interconnects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗