Search NASA⌕ Search

SEARCH · Search NASA

Results for “AMORPHOUS STATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Eliminating chemo-mechanical degradation of lithium solid-state battery cathodes during >4.5 V cycling using amorphous Nb2O5 coatings

Abstract Lithium solid-state batteries offer improved safety and energy density. However, the limited stability of solid electrolytes (SEs), as well as irreversible structural and chemical changes in the cathode active material, can result in inferior electrochemical performance, particularly during high-voltage cycling (>4.3 V vs Li/Li + ). Therefore, new materials and strategies are needed to stabilize the cathode/SE interface and preserve the cathode material structure during high-voltage cycling. Here, we introduce a thin (~5 nm) conformal coating of amorphous Nb 2 O 5 on single-crystal LiNi 0.5 Mn 0.3 Co 0.2 O 2 cathode particles using rotary-bed atomic layer deposition (ALD). Full cells with Li 4 Ti 5 O 12 anodes and Nb 2 O 5 -coated cathodes demonstrate a higher initial Coulombic efficiency of 91.6% ± 0.5% compared to 82.2% ± 0.3% for the uncoated samples, along with improved rate capability (10x higher accessible capacity at 2C rate) and remarkable capacity retention during extended cycling (99.4% after 500 cycles at 4.7 V vs Li/Li + ). These improvements are associated with reduced cell polarization and interfacial impedance for the coated samples. Post-cycling electron microscopy analysis reveals that the Nb 2 O 5 coating remains intact and prevents the formation of spinel and rock-salt phases, which eliminates intra-particle cracking of the single-crystal cathode material. These findings demonstrate a potential pathway towards stable and high-performance solid-state batteries during high-voltage operation.

Science & Technology - Other Topics↗
NASA NTRS1978

Surface temperatures and glassy state investigations in tribology, part 1

The research in this report is divided into two categories: (1) lubricant rheological behavior, and (2) thermal behavior of a simulated elastohydrodynamic contact. The studies of the lubricant rheological behavior consists of high pressure, low shear rate viscosity measurements, viscoelastic transition measurements, by volume dilatometry, dielectric transitions at atmospheric pressure and light scattering transitions. Lubricant shear stress-strain behavior in the amorphous glassy state was measured on several fluids. It appears clear from these investigations that many lubricants undergo viscoplastic transitions in typical EHD contacts and that the lubricant has a limiting maximum shear stress it can support which in turn will determine the traction in the contact except in cases of very low slide-roll ratio. Surface temperature measurements were made for a naphthenic mineral oil and a polyphenyl ether. The maximum surface temperature in these experiments was approximately symmetrical about the zero slide-roll ration except for absolute values of slide-roll ratio greater than about 0.9. Additional surface temperature measurements were made in contacts with rough surfaces where the composite surface roughness was approximately equal to the EHD film thickness. A regression analysis was done to obtain a predictive equation for surface temperatures as a function of pressure, sliding speed, and surface roughness. A correction factor for surface roughness effects to the typical flash temperature analysis was found.

Winer, W. O.↗
DOE OSTI2023

Unveiling the structure and electronic characteristics of amorphous GeS for high performance threshold switching

Ovonic threshold switching selectors are widely studied owing to the essential application in high density phase-change memory. Amorphous GeS is proposed as a potential candidate for the excellent performance. However, the knowledge of amorphous GeS is still insufficient up to date. Here, we have studied the structure and electronic characteristics of GeS in the amorphization process, by using ab initio molecular dynamics simulations. The results indicate that the amorphous GeS is mainly made up of Ge–S bonds. The Ge- and S-centered clusters are dominantly in the form of octahedral structures in liquid GeS. Furthermore, during the amorphization process, most of Ge-centered clusters become highly coordinated octahedrons while a small number of Ge-centered clusters change to tetrahedrons, and the S-centered clusters deviate from the octahedral structure gradually. In addition, the large bandgap and the relatively small mid-gap states in amorphous GeS lead to a high switching voltage.

42 ENGINEERING↗
DOE OSTI2019

Utilizing TiO 2 amorphous precursors for polymorph selection: An in situ TEM study of phase formation and kinetics

Selective synthesis of metastable polymorphs requires a fundamental understanding of the complex energy landscapes in which these phases form. Recently, the development of in situ high temperature and controlled atmosphere transmission electron microscopy has enabled the direct observation of nucleation, growth, and phase transformations with near atomic resolution. In this work, we directly observe the crystallization behavior of amorphous TiO 2 thin films grown under different pulsed laser deposition conditions and quantify the mechanisms behind metastable crystalline polymorph stabilization. Films deposited at 10 mTorr chamber oxygen pressure crystallize into nanocrystalline Anatase at 325 degrees C, whereas films deposited at 2 mTorr crystallize into significantly larger needle-like grains of Brookite and Anatase at 270 degrees C. Increasing film deposition rate by a factor of 4 results in a 10x increase in the crystalline growth front velocity as well as a decrease in crystallization temperature from 270 degrees C to 225 degrees C. Engineering the amorphous precursor state through deposition conditions therefore provides routes to microstructure control and the accessibility of higher energy metastable phases.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High-Power Impulse Magnetron Sputter Deposition of Ultrathick Amorphous Carbon

Diamond-like carbon (DLC) is a material of interest for inertial confinement fusion (ICF) ablators. However, the deposition of ultrathick DLC coatings, as required for ICF ablator fabrication, remains a challenge. Here, in this study, we use high-power impulse magnetron sputtering to deposit DLC and demonstrate a set of process parameters leading to high-purity, amorphous DLC coatings with a low compressive residual stress of <400 MPa. Coatings with thicknesses of up to 80 μm are demonstrated.

amorphous carbon↗
DOE OSTI2024

Effects of Nonequilibrium Atomic Structure on Ionic Diffusivity in LLZO: A Classical and Machine Learning Molecular Dynamics Study

To improve the performance of electrochemical devices, it is essential to understand the effects of nonequilibrium motifs in solids, such as grain boundaries, amorphous phases, and highly strained regions, on atomic-scale transport and stability. Molecular dynamics simulations are used to explore the combined effect of far-from-equilibrium atomic structures and the choice of interatomic potential on ionic diffusivity predictions for Li 7 La 3 Zr 2 O 12 (LLZO), a promising solid electrolyte for all-solid-state batteries. Amorphization and high strain are considered using both classical Buckingham interatomic potentials and machine learning force fields. Here we find that both crystalline expansion and amorphization tend to slow diffusion, although the different physical encodings in the two potentials impact the properties in different ways. We trace these variations to a combination of structural and transport factors, the contributions of which are deconvoluted computationally. Graph-based analysis reveals that the variations for amorphous LLZO arise from the connectivity of diffusion pathways within the predicted structures, which generally correlates with diffusivity and is notably higher for structures generated by the machine learning force fields. Our study provides additional insight into the relationship between atomic structure and diffusivity in LLZO, while also highlighting the need for care in choosing and validating potentials to simulate far from equilibrium structures.

25 ENERGY STORAGE↗
DOE OSTI2025

The Birth of Minerals: From Single Step to Multiple Step Mechanisms

Mineral formation from ions in aqueous solutions begins with complex initial stages, where amorphous and liquid-like precursors play pivotal roles before crystalline growth occurs. Both classical and non-classical nucleation and growth theories, introduced in previous chapters, offer explanations, each with their own strengths and limitations, for the complex intermediate phases observed in experimental research. Analytical techniques play a critical role in detecting and characterizing precursor phases, offering valuable insights into nucleation and growth mechanisms across various temporal and spatial scales. In conclusion, molecular dynamics and modelling provide in-depth perspectives on these phases, allowing for a closer examination of their nucleation and growth mechanisms at the molecular level, and revealing the intricate processes that govern their behaviour.

amorphous↗
DOE OSTI2021

New insights into the mechanism governing the elasticity of calcium silicate hydrate gels exposed to high temperature: A molecular dynamics study

When exposed to fire, the integrity of cement-based materials is governed by thermally-induced changes in the mechanical properties of their binding phase, i.e., the calcium–silicate–hydrate (C–S–H) gel. However, the effect of temperature on the structure, density, and mechanical properties of C–S–H remains only partially known. Here, based on reactive molecular dynamics simulations, we reveal the nature of thermally-induced damage in C–S–H gels. In general, we show that, at the atomic scale, exposure to high temperature results in partial dehydration, volumetric shrinkage, disordering, and stiffening in the C–S–H grains. However, we show that the thermal response of C–S–H strongly depends on its chemical composition, wherein C–S–H systems associated with lower Ca/Si molar ratios are able to undergo higher temperatures before amorphization. Based on these results, we demonstrate that the stiffness of C–S–H gels (i.e., including porosity—as probed by nanoindentation) is governed by a competition between the stiffening of the grains and the decrease in packing density—wherein the latter eventually become predominant.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of ZnO on the whiteness of white Portland cement clinker

The addition of ZnO to significantly improve the Hunter whiteness of white Portland cement (WPC) clinkers is introduced in this paper. The effects of ZnO on the whiteness of WPC were studied by chroma analysis, X-ray diffraction (XRD), the Rietveld method, hydration heat measurements and SEM-EDS. The results showed that adding ZnO increased the visible light reflectance, increased the brightness (L{sup ⁎}), and reduced the yellowness (b{sup ⁎}) of WPC clinker with high Fe{sub 2}O{sub 3}. Therefore, ZnO can increase the whiteness of WPC clinker. Zn was mainly distributed in the amorphous phase and unquantifiable crystalline phase (ACn), and then dissolved in the silicate phase. ZnO stabilized R-C{sub 3}S, reduced the crystallization of C{sub 3}A, and increased the ACn content. ZnO increased the amount of Fe in the ACn and minerals, thereby reducing the formation of C{sub 4}AF and improving whiteness. ZnO increased the accumulated heat of hydration but prolonged the induction period. This method provides a new approach for the WPC industry to broaden sources of raw materials and improve product quality.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Lubricant Rheology in Concentrated Contacts

A revue of experimental investigations of lubricant behaviour in highly stressed situations shows that a Newtonian model for lubricant rheology is insufficient for explanation of traction behaviour. The oil film build-up, on the other hand, is fairly well predicted using a Newtonian lubricant model except at high slide to roll ratios and at very high loads, where the non-Newtonian behaviour starts to be important already outside the Hertzian contact area. Two main types of experiments are reported: static and dynamic. In static experiments the pressure is typically applied to the lubricant more than a million times longer than in an EHD contact. Depending on the pressure-temperature history of the experiment the lubricant will become a crystallized or amorphous solid at high pressures. In dynamic experiments, where the pressure is applied as short time as in real EHD contacts, the oil is in an amorphous solid state. Depending on the viscosity, time-scale, elasticity of the oil and the bearing surfaces, the oil film pressure, shear strain rate and the type of lubricant, different properties of the oil are important for prediction of shear stresses in the oil. This can be seen from the different proposed models for the lubricant, where it is described as being for instance a Newtonian liquid, an elastic liquid, a plastic liquid and an elastic-plastic solid.

Bo O Jacobson↗
NASA NTRS1993

Thermal processing of omicron-terphenyl - A Raman study

Raman spectra from omicron-terphenyl sealed in glass capillary tubes were acquired over temperatures ranging from 233 to 343 K. Over this temperature range, omicron-terphenyl can exist in the solid-crystalline, molten, supercooled-liquid, and amorphous-glassy states. Representative structure-sensitive spectra are presented along with a qualitative description. The lattice spectral feature occurring at a Raman shift of 123/cm displays abrupt changes in profile and intensity as melting and glass transition occur. The intensity ratio of the C-C stretching 996/cm line and C-H stretching line at 1008/cm displays a change related to the transformation of the ordered-crystalline phase to the disordered-liquid or glassy state. At a Raman shift of 1162/cm the solid-crystalline state shows a splitting due to the effect of the crystal field. The possibility of using these structure-sensitive Raman characteristics for in situ diagnostics during materials processing is discussed.

Biswas, A.↗
DOE OSTI2020

Long-Range Ordered Amorphous Atomic Chains as Building Blocks of a Superconducting Quasi-One-Dimensional Crystal

Crystalline and amorphous structures are two of the most common solid-state phases. Crystals having orientational and periodic translation symmetries are usually both short-range and long-range ordered, while amorphous materials have no long-range order. Short-range ordered but long-range disordered materials are generally categorized into amorphous phases. In contrast to the extensively studied crystalline and amorphous phases, the combination of short-range disordered and long-range ordered structures at the atomic level is extremely rare and so far has only been reported for solvated fullerenes under compression. Here, a report on the creation and investigation of a superconducting quasi-1D material with long-range ordered amorphous building blocks is presented. Using a diamond anvil cell, monocrystalline (TaSe4)(2)I is compressed and a system is created where the TaSe(4)atomic chains are in amorphous state without breaking the orientational and periodic translation symmetries of the chain lattice. Strikingly, along with the amorphization of the atomic chains, the insulating (TaSe4)(2)I becomes a superconductor. The data provide critical insight into a new phase of solid-state materials. The findings demonstrate a first ever case where superconductivity is hosted by a lattice with periodic but amorphous constituent atomic chains.

combination of crystalline and amorphous structure↗
DOE OSTI2022

Structural Phase Transitions between Layered Indium Selenide for Integrated Photonic Memory

The primary mechanism of optical memoristive devices relies on phase transitions between amorphous and crystalline states. The slow or energy-hungry amorphous–crystalline transitions in optical phase-change materials are detrimental to the scalability and performance of devices. Leveraging an integrated photonic platform, nonvolatile and reversible switching between two layered structures of indium selenide (In 2 Se 3 ) triggered by a single nanosecond pulse is demonstrated. The high-resolution pair distribution function reveals the detailed atomistic transition pathways between the layered structures. With interlayer “shear glide” and isosymmetric phase transition, switching between the α- and β-structural states contains low re-configurational entropy, allowing reversible switching between layered structures. Broadband refractive index contrast, optical transparency, and volumetric effect in the crystalline–crystalline phase transition are experimentally characterized in molecular-beam-epitaxy-grown thin films and compared to ab initio calculations. Finally, the nonlinear resonator transmission spectra measure of incremental linear loss rate of 3.3 GHz, introduced by a 1.5 µm-long In 2 Se 3 -covered layer, resulted from the combinations of material absorption and scattering.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Plasma Synthesis of Spherical Crystalline and Amorphous Electrolyte Nanopowders for Solid-State Batteries

Here, we demonstrate the theory-guided plasma synthesis of high purity nanocrystalline Li 3.5 Si 0.5 P 0.5 O 4 and fully amorphous Li 2.7 Si 0.7 P 0.3 O 3.17 N 0.22 . The synthesis involves the injection of single or mixed phase precursors directly into a plasma torch. As the material exits the plasma torch, it is quenched into spherical nanocrystalline or amorphous nanopowders. This process has virtually zero Li loss and allows for the inclusion of N, which is not accessible with traditional synthesis methods. Finally, we further demonstrate the ability to sinter the crystalline nanopowder into a dense electrolyte membrane at 800 °C, well below the traditional 1000 °C required for a conventional Li 3.5 Si 0.5 P 0.5 O 4 powder.

25 ENERGY STORAGE↗
DOE OSTI2023

Probing Molecular Packing of Amorphous Pharmaceutical Solids Using X-ray Atomic Pair Distribution Function and Solid-State NMR

The structural investigation of amorphous pharmaceuticals is of paramount importance in comprehending their physicochemical stability. However, it has remained a relatively underexplored realm primarily due to the limited availability of high-resolution analytical tools. Here in this study, we utilized the combined power of X-ray pair distribution functions (PDFs) and solid-state nuclear magnetic resonance (ssNMR) techniques to probe the molecular packing of amorphous posaconazole and its amorphous solid dispersion at the molecular level. Leveraging synchrotron X-ray PDF data and employing the empirical potential structure refinement (EPSR) methodology, we unraveled the existence of a rigid conformation and discerned short-range intermolecular C–F contacts within amorphous posaconazole. Encouragingly, our ssNMR 19 F– 13 C distance measurements offered corroborative evidence supporting these findings. Furthermore, employing principal component analysis on the X-ray PDF and ssNMR data sets enabled us to gain invaluable insights into the chemical nature of the intermolecular interactions governing the drug–polymer interplay. These outcomes not only furnish crucial structural insights facilitating the comprehension of the underlying mechanisms governing the physicochemical stability but also underscore the efficacy of synergistically harnessing X-ray PDF and ssNMR techniques, complemented by robust modeling strategies, to achieve a high-resolution exploration of amorphous structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1982

Friction and surface chemistry of some ferrous-base metallic glasses

The friction properties of some ferrous-base metallic glasses were measured both in argon and in vacuum to a temperature of 350 C. The alloy surfaces were also analyzed with X-ray photoelectron spectroscopy to identify the compounds and elements present on the surface. The results of the investigation indicate that even when the surfaces of the amorphous alloys, or metallic glasses, are atomically clean, bulk contaminants such as boric oxide and silicon dioxide diffuse to the surfaces. Friction measurements in both argon and vacuum indicate that the alloys exhibit higher coefficients of friction in the crystalline state than they do in the amorphous state.

Miyoshi, K.↗