Search NASA⌕ Search

SEARCH · Search NASA

Results for “AXIAL COMPRESSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1951

Buckling of thin-walled cylinder under axial compression and internal pressure

An investigation was made of a thin-walled cylinder under axial compression and various internal pressures to study the effect of the internal pressure on the compressive buckling stress of the cylinder. A theoretical analysis based on a large-deflection theory was also made. The theoretically predicted increase of compressive buckling stress due to internal pressure agrees fairly well with the experimental results. (author)

Lo, Hsu↗
NASA NTRS1947

Critical stress of thin-walled cylinders in axial compression

Empirical design curves are presented for the critical stress of thin-walled cylinders loaded in axial compression. These curves are plotted in terms of nondimensional parameters of small-deflection theory and are compared with theoretical curves derived for the buckling of cylinders with simply supported and clamped edges. An empirical equation is given for the buckling of cylinders having a length-radius ratio greater than about 0.75. The test data obtained from various sources follow the general trend of the theoretical curve for cylinders with clamped edges, agreeing closely with the theory in the case of short cylinders, but falling considerably below the theoretical results for long cylinders. The discrepancy in the case of long cylinders increases with increasing values of the ratio of radius to wall thickness. Plotting curves for different values of this ratio reduces the scatter in the test data and a certain degree of correlation with theory is achieved. Advantage is taken of this correlation to obtain estimated design curves for cylinders with simply supported edges, for which little experimental information is available. (author)

Batdorf, S B↗
NASA NTRS1947

Critical stress of thin-walled cylinders in axial compression

Empirical design curves are presented for the critical stress of thin-wall cylinders loaded in axial compression. These curves are plotted in terms of the nondimensional parameters of small-deflection theory and are compared with theoretical curves derived for the buckling of cylinders with simply supported and clamped edges. An empirical equation is given for the buckling of cylinders having a length-radius ratio greater than about 0.75.

Batdorf, S B↗
NASA NTRS1973

Buckling of unstiffened and ring stiffened cylindrical shells under axial compression.

Bifurcation stresses and initial postbuckling behavior of both unstiffened and outside ring stiffened circular cylindrical shells under axial compression are analyzed. The shells are assumed to have axisymmetric sinusoidal imperfections with arbitrary wavelengths and amplitudes. It is found that for large imperfection amplitudes and wavelengths both the unstiffened and the stiffened shells have extremely small bifurcation loads. The postbuckling analysis shows that for small imperfection amplitudes the bifurcations from the axisymmetric state are initially unstable and collapse is associated with the bifurcation points. However, for larger values of the imperfection amplitudes the bifurcations are stable. For unstiffened shells the transition from unstable to stable bifurcations can take place at very small values of the load. On the other hand, for stiffened shells it is found that bifurcations at load levels less than about 40% of the classical buckling load have stable initial postbuckling behavior.

Pedersen, P. T.↗
NASA NTRS1985

A theory of post-stall transients in axial compression systems. I - Development of equations

An approximate theory is presented for post-stall transients in multistage axial compression systems. The theory leads to a set of three simultaneous nonlinear third-order partial differential equations for pressure rise, and average and disturbed values of flow coefficient, as functions of time and angle around the compressor. By a Galerkin procedure, angular dependence is averaged, and the equations become first order in time. These final equations are capable of describing the growth and possible decay of a rotating-stall cell during a compressor mass-flow transient. It is shown how rotating-stall-like and surgelike motions are coupled through these equations, and also how the instantaneous compressor pumping characteristic changes during the transient stall process.

Moore, F. K.↗
NASA NTRS1972

Optimum mass-strength analysis for orthotropic ring-stiffened cylinders under axial compression

An analysis was developed to calculate the minimum mass-strength curve for an orthotropic cylinder subjected to axial compressive loading. The analysis, which includes the effects of ring and stringer eccentricities, is in a general form so that various cylinder wall and stiffener geometries can be considered. Several different ring-stiffened orthotropic configurations were studied. The minimum mass-strength curves and the dimensions associated with these curves are presented for (in order of decreasing efficiency) a tubular double bead, a nonsymmetric double bead, a Z-stiffened skin, and a trapezoidal corrugation. A comparison of efficiencies of the configurations shows a tubular element cylinder to be more efficient than a 3-percent core-density honeycomb-sandwich cylinder. It was found that for an optimized Z-stiffened skin, the location of the Z-stiffeners (internal or external) made a negligible difference in efficiency.

Shideler, J. L.↗
NASA NTRS1972

Effect of a circular hole on the buckling of cylindrical shells loaded by axial compression.

An experimental and analytical investigation of the effect of a circular hole on the buckling of thin cylindrical shells under axial compression was carried out. The experimental results were obtained from tests performed on seamless electroformed copper shells and Mylar shells with a lap joint seam. These results indicated that the character of the shell buckling was dependent on a parameter which is proportional to the hole radius divided by the square root of the product of the shell radius and thickness. For small values of this parameter, there was no apparent effect of the hole on the buckling load. For slightly larger values of the parameter, the shells still buckled into a general collapse configuration, but the buckling loads were sharply reduced as the parameter increased. For still larger values of the parameter, the buckling loads were further reduced, and the shells buckled into a stable local buckling configuration.

Starnes, J. H., Jr.↗
NASA NTRS1985

Postbuckling behavior of selected curved stiffened graphite-epoxy panels loaded in axial compression

Results of an experimental and analytical study of the postbuckling behavior of selected curved stiffened graphite-epoxy panels loaded in axial compression are presented. The postbuckling response and failure characteristics of the panels are described. Each panel had four equally-spaced I-shaped stiffeners and 16-ply quasi-isotropic skins. Panels with three different stiffener spacings were tested. Failure of all panels initiated in a skin-stiffener interface region. Analytical results from a nonlinear general shell finite element analysis computer code correlate well with typical postbuckling test results up to failure. The analytical modeling detail necessary to predict accurately the response of the panel is described. Measured initial geometric imperfections were included in the postbuckling analysis.

Knight, N. F., Jr.↗
NASA NTRS1972

Minimum weight design of ring and stringer stiffeners for axially compressed cylindrical shells with and without internal pressure

Results of analytical study to determine desirable ring and stringer stiffener parameters and proportions for axially compressed stiffened isotropic cylinders with and without internal pressure are presented. This investigation examines the panel and general instability buckling modes of a stiffened cylindrical shell and from this determines desirable stiffener parameters and proportions. Classical buckling equations are used which retain the important effects of the stiffeners. The results determined by using the simpler classical buckling equations are then spot checked and verified using buckling equations which considered discrete ring stiffeners and nonlinear prebuckling deformations. For both rings and stringers, T-shaped stiffeners are preferable and the effects to stiffener shape are much more pronounced at low or zero values of the internal pressure parameter. Simple analytical expressions are developed and presented which express the stiffener area parameter, the ratio of stiffener area and elastics to shell wall area and elastic modulus, in terms of the cylinder geometry and internal pressure parameter.

Block, D. L.↗
NASA NTRS2010

Comparison of Methods to Predict Lower Bound Buckling Loads of Cylinders Under Axial Compression

Results from a numerical study of the buckling response of two different orthogrid stiffened circular cylindrical shells with initial imperfections and subjected to axial compression are used to compare three different lower bound buckling load prediction techniques. These lower bound prediction techniques assume different imperfection types and include an imperfection based on a mode shape from an eigenvalue analysis, an imperfection caused by a lateral perturbation load, and an imperfection in the shape of a single stress-free dimple. The STAGS finite element code is used for the analyses. Responses of the cylinders for ranges of imperfection amplitudes are considered, and the effect of each imperfection is compared to the response of a geometrically perfect cylinder. Similar behavior was observed for shells that include a lateral perturbation load and a single dimple imperfection, and the results indicate that the predicted lower bounds are much less conservative than the corresponding results for the cylinders with the mode shape imperfection considered herein. In addition, the lateral perturbation technique and the single dimple imperfection produce response characteristics that are physically meaningful and can be validated via testing.

Haynie, Waddy T.↗
NASA NTRS2004

Test and Analyses of a Composite Multi-Bay Fuselage Panel Under Uni-Axial Compression

A composite panel containing three stringers and two frames cut from a vacuum-assisted resin transfer molded (VaRTM) stitched fuselage article was tested under uni-axial compression loading. The stringers and frames divided the panel into six bays with two columns of three bays each along the compressive loading direction. The two frames were supported at the ends with pins to restrict the out-of-plane translation. The free edges of the panel were constrained by knife-edges. The panel was modeled with shell finite elements and analyzed with ABAQUS nonlinear solver. The nonlinear predictions were compared with the test results in out-of-plane displacements, back-to-back surface strains on stringer flanges and back-to-back surface strains at the centers of the skin-bays. The analysis predictions were in good agreement with the test data up to post-buckling.

Li, Jian↗
NASA NTRS1999

Analytical Prediction of Damage Growth in Notched Composite Panels Loaded in Axial Compression

A progressive failure analysis method based on shell elements is developed for the computation of damage initiation and growth in stiffened thick-skin stitched graphite-epoxy panels loaded in axial compression. The analysis method involves a step-by-step simulation of material degradation based on ply-level failure mechanisms. High computational efficiency is derived from the use of superposed layers of shell elements to model each ply orientation in the laminate. Multiple integration points through the thickness are used to obtain the correct bending effects through the thickness without the need for ply-by-ply evaluations of the state of the material. The analysis results are compared with experimental results for three stiffened panels with notches oriented at 0, 15 and 30 degrees to the panel width dimension. A parametric study is performed to investigate the damage growth retardation characteristics of the Kevlar stitch lines in the pan

Ambur, Damodar R.↗
NASA NTRS1984

Postbuckling behavior of axially compressed graphite-epoxy cylindrical panels with circular holes

The results of an experimental and analytical study of the effects of circular holes on the postbuckling behavior of graphite-epoxy cylindrical panels loaded in axial compression are presented. The STAGSC-1 general shell analysis computer code is used to determine the buckling and postbuckling response of the panels. The loaded, curved ends of the specimens were clamped by fixtures and the unloaded, straight edges were simply supported by knife-edge restraints. The panels are loaded by uniform end shortening to several times the end shortening at buckling. The unstable equilibrium path of the postbuckling response is obtained analytically by using a method based on controlling an equilibrium-path-arc-length parameter instead of the traditional load parameter. The effects of hole diameter, panel radius, and panel thickness on postbuckling response are considered in the study. Experimental results are compared with the analytical results and the failure characteristics of the graphite-epoxy panels are described.

Knight, N. F., Jr.↗