Search NASA⌕ Search

SEARCH · Search NASA

Results for “Air”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1952

Preliminary Air-Flow and Thrust Calibrations of Several Conical Cooling-Air Ejectors with a Primary to Secondary Temperature Ratio of 1.0: Diameter Ratios of 1.06 and 1.40 - 2

An investigation was made of the performance of nine conical cooling-air ejectors at primary jet pressure ratios from 1 to 10, secondary pressure ratios to 4.0, and a temperature ratio of unity. This phase of the investigation was limited to conical ejectors having shroud exit to primary nozzle exit diameter ratios of 1.06 and 1.40, with several spacing ratios for each. The experimental results indicated that the pumping range and amount of cooling-air flow obtained with a 1.06 diameter ratio ejector were relatively small for cooling purposes but that the maximum possible thrust loss, which occurred with no secondary flow, was only 7 percent of convergent nozzle thrust. The 1.40 diameter ratio ejector produced a large cooling air flow and showed a possible thrust loss of 29.5 percent with no cooling air flow. Thrust gains were attained with ejectors of both diameter ratios at secondary pressure ratios greater than 1.0. The limiting primary pressure ratio below which an ejector can operate at a specific secondary pressure ratio (cut-off point) may be estimated for various flight conditions from data contained herein.

Greathouse, W. K.↗
NASA NTRS1949

Heat Transfer from High-Temperature Surfaces to Fluids. III - Correlation of Heat-Transfer Data for Air Flowing in Silicon Carbide Tube with Rounded Entrance, Inside Diameter of 3/4 Inch, and Effective Length of 12 Inches: Correlation of Heat-Transfer Data for Air Flowing in Silicon Carbide Tube with Rounded Entrance, Inside Diameter of 3/4 Inch, and Effective Length of 12 Inches - Part 3

A heat-transfer investigation was conducted with air flowing through an electrically heated silicon carbide tube with a rounded entrance, an inside diameter of 3/4 inch, and an effective heat-transfer length of 12 inches over a range of Reynolds numbers up to 300,000 and a range of average inside-tube-wall temperature up to 2500 R. The highest corresponding local outside-tube-wall temperature was 3010 R. Correlation of the heat-transfer data using the conventional Nueselt relation wherein physical properties of the fluid were evaluated at average bulk temperature resulted in a separation of data with tube-wall-temperature level. A satisfactory correlation of the heat-transfer data was obtained, however, by the use of modified correlation parameters wherein the mass velocity G (or product of average air density and velocity evaluated at bulk temperature P(sub b)V(sub b)) in the Reynolds number was replaced by the product of average air velocity evaluated at the bulk temperature and density evaluated at either the average inside-tube-wall temperature or the average film temperature; in addition, all the physical properties of air were correspondingly evaluated at either the average inside-tube-wall temperature or the average film temperature.

Sams, Eldon W.↗
NASA NTRS2011

Lessons Learned from AIRS: Improved Determination of Surface and Atmospheric Temperatures Using Only Shortwave AIRS Channels

This slide presentation reviews the use of shortwave channels available to the Atmospheric Infrared Sounder (AIRS) to improve the determination of surface and atmospheric temperatures. The AIRS instrument is compared with the Infrared Atmospheric Sounding Interferometer (IASI) on-board the MetOp-A satellite. The objectives of the AIRS/AMSU were to (1) provide real time observations to improve numerical weather prediction via data assimilation, (2) Provide observations to measure and explain interannual variability and trends and (3) Use of AIRS product error estimates allows for QC optimized for each application. Successive versions in the AIRS retrieval methodology have shown significant improvement.

Susskind, Joel↗
NASA NTRS2011

Gulf of Mexico Air Quality: CALIPSO Support for Gulf of Mexico Air Quality Relating to the Deepwater Horizon Oil Spill

On April 20, 2010, an oil platform belonging to BP exploded and leaked a huge volume of oil into the Gulf of Mexico. In an effort to control the spread of the oil, BP applied dispersants such as Corexit and conducted in-situ burnings of the oil. This catastrophe created a complex chain of events that affected not only the fragile water and land ecosystems, but the humans who breathe the air every day. Thousands of people were exposed to fumes associated with oil vapors from the spill, burning of the oil, and the toxic mixture of dispersants. While aiding in clean-up efforts, local fishermen were directly exposure to fumes when working on the Gulf. A notable amount of Gulf Coast residents were also exposed to the oil fumes as seasonal southeasterly winds blew vapors toward land. The Volatile Organic Compounds (VOC) found in oil vapors include: benzene, toluene, ethyl benzene, xylene, naphthalene, hydrogen sulfide and particulate matter (PM). Increases in water temperature and sunlight due to the summer season allow for these VOCs and PM to evaporate into the air more rapidly. Aside from the VOCs found in oil vapors, the dispersant being used to break up the oil is highly toxic and is thought to be even more toxic than the oil itself (EPA website, 2010). To protect human health, the environment, and to make informed policy decisions relevant to the spill, the EPA Region 6 has continuously monitored the affected areas carefully for levels of pollutants in the outdoor air that are associated with petroleum products and the burning of oil along the coast. In an effort to prevent, prepare for, and respond to future oil spills that occur in and around inland waters of the United States, the EPA has been working with local, state, and federal response partners. Air quality measurements were collected by the EPA at five active monitoring systems stationed along the coast.

Nguyen, Myngoc T.↗
NASA NTRS2019

Air-To-Air Background Oriented Schlieren Technique

An air-to-air background-oriented Schlieren system and method for measuring and rendering visible density changes in air that cause a refractive index change by an airborne vehicle. A sensor aircraft equipped with a high-speed visible spectrum camera travels at low airspeed on a predetermined route and on a level altitude over a background having consistent contrast and sunlight reflectivity. The target aircraft, traveling on the same predetermined route but at an altitude between the sensor aircraft and the ground (background) passes beneath the sensor aircraft. The camera on the sensor aircraft captures a series of images including a reference image immediately before the target aircraft enters the image frame followed by several data images as the target aircraft passes through the image frame. The data images are processed to calculate density gradients around the target aircraft. These density gradients include shockwaves, vortices, engine exhaust, and wakes. Air density gradients cause a refractive index change in the fluid and a slight distortion in the background pattern of the data image. Image processing that compares the data image to the reference image yields the difference caused by the density gradient.

Heineck, James Thomas↗
NASA NTRSDate not supplied

Learning Based Edge Computing in Air-to-Air Communication Network

This paper studies learning-based edge computing and communication in a dynamic Air-to-Air Ad-hoc Network (AAAN). Due to spectrum scarcity, we assume the number of Air-to-Air (A2A) communication links is greater than that of the available frequency channels, such that some communication links have to share the same channel, causing co-channel interference. We formulate the joint channel selection and power control optimization problem to maximize the aggregate spectrum utilization efficiency under resource and fairness constraints. A distributed deep Q learning-based edge computing and communication algorithm is proposed to find the optimal solution. In particular, we design two different neural network structures and each communication link can converge to the optimal operation by exploiting only the local information from its neighbors, making it scalable to large networks. Finally, experimental results demonstrate the effectiveness of the proposed solution in various AAAN scenarios.

Zhe Wang↗
NASA NTRS2022

Delaware Basin Health and Air Quality: Spatiotemporal Analysis of Air Pollutants Collected from Ground and Space Instruments Around the Guadalupe Mountains and Carlsbad Caverns National Parks

Nitrogen dioxide (NO2) is a precursor for secondary air pollutants, which are associated with decreased visibility, and decreased ecosystem and respiratory health. NO2 is a growing threat to national parks within the Delaware Basin where nearby oil and gas activity contributes to deteriorating park conditions, implying adverse effects on the local tourism economy and public health. To demonstrate spatial and temporal patterns of air pollution in the parks, we examined average monthly, seasonal, and annual tropospheric column concentrations of NO2 in Carlsbad Caverns (CAVE) and Guadalupe Mountain (GUMO) National Parks. We used both the NASA Ozone Monitoring Instrument (OMI) and the European Space Agency (ESA) Tropospheric Monitoring Instrument (TROPOMI) to map NO2 tropospheric column densities. Using ground-based emissions values from the Environmental Protection Agency National Emissions Inventory (NEI) for two nearby natural gas processing plants (Indian Basin Gas Plant, South Carlsbad Plant), we extrapolated monthly trends from these point sources and compared seasonal emissions levels with the measurements recorded by OMI and TROPOMI. The NEI data show an 8% increase in flaring from 2013–2021. OMI measured a 38.3% NO2 increase over the Delaware Basin, 15.29% increase over CAVE, and 4.26% decrease over GUMO from 2011–2018. TROPOMI measured a -1% NO2 change over the Delaware Basin, 3% over CAVE, and 7% over GUMO from 2018–2020. The analysis indicates a positive correlation between emissions from fossil fuel exploration and NO2 concentrations above CAVE and GUMO. This information will inform National Park Service air quality monitoring and policy efforts to ensure compliance with the Clean Air Act.

Sean Cusick↗
NASA NTRSDate not supplied

A Safety-Driven Approach to Exploring and Comparing Air Traffic Management Concepts for Enabling Urban Air Mobility

There is broad recognition that the high tempo and density of Urban Air Mobility (UAM) operations will require identifying new Air Traffic Management (ATM) concepts to safely integrate UAM air traffic into the airspace alongside existing air traffic. However, the simulation models used to compare ATM concepts today are difficult to apply during the early stages of concept development and do not offer enough support in identifying potential new concepts. In addition, they have limited ability to evaluate ATM concepts in terms of safety, security, and other key emergent properties. Instead of using simulation to evaluate ATM concepts, this paper demonstrates how a safety-driven systems engineering approach based on Systems-Theoretic Accident Model and Processes (STAMP) can be used to design properties such as safety into an ATM system from the earliest stages of development. Using a hazard analysis technique called Systems-Theoretic Process Analysis (STPA), system requirements and the desired ATM behavior are derived. As an example, two possible ATM concepts to implement that behavior are compared to identify their safety-related benefits and tradeoffs. This new approach enables (1) systematic exploration of alternative ATM concepts and (2) identification of the safety-related tradeoffs between concepts as early as possible in the development process.

system safety↗
NASA NTRS2023

An Interface Specification for Urban Air Mobility Performance Models to Support Air Traffic Management Research

Performance modeling of Urban Air Mobility vehicles in support of Air Traffic Management research poses new challenges. These aircraft often rely on a combination of fixed-wing and rotorcraft performance capabilities to enable a new and still-evolving concept of high-volume operations in densely populated areas. These characteristics lead to variability in performance model format and functionality, complicating model development and leading to difficulties for users integrating the models into their applications. This paper describes an interface specification for performance models that is intended to help address this issue. The interface aims to support the core functionality of performance models while also providing the necessary flexibility to both model developers and users. The specification describes the required model documentation, required inputs to the model, and required outputs from the model in general terms that are adaptable to most programming languages. The utilization of an appropriate interface specification will support the development of an Urban Air Mobility performance model database and help to improve interoperability of these models for a broad array of user applications.

Trajectory Prediction↗
NASA NTRS2023

An Interface Specification for Urban Air Mobility Performance Models to Support Air Traffic Management Research

Performance modeling of Urban Air Mobility vehicles in support of Air Traffic Management research poses new challenges. These aircraft often rely on a combination of fixed-wing and rotorcraft performance capabilities to enable a new and still-evolving concept of high-volume operations in densely populated areas. These characteristics lead to variability in performance model format and functionality, complicating model development and leading to difficulties for users integrating the models into their applications. This paper describes an interface specification for performance models that is intended to help address this issue. The interface aims to support the core functionality of performance models while also providing the necessary flexibility to both model developers and users. The specification describes the required model documentation, required inputs to the model, and required outputs from the model in general terms that are adaptable to most programming languages. The utilization of an appropriate interface specification will support the development of an Urban Air Mobility performance model database and help to improve interoperability of these models for a broad array of user applications.

Trajectory Prediction↗
NASA NTRS1975

Properties of air and combustion products of fuel with air

Thermodynamic and transport properties have been calculated for air, the combustion products of natural gas and air, and combustion products of ASTM-A-1 jet fuel and air. Properties calculated include: ratio of specific heats, molecular weight, viscosity, specific heat, thermal conductivity, Prandtl number, and enthalpy.

Poferl, D. J.↗
NASA NTRS1975

Flight testing air-to-air missiles for flutter

The philosophy of the design of air-to-air missiles and hence of flight testing them for flutter differs from that of manned aircraft. Primary emphasis is put on analytical and laboratory evaluation of missile susceptibility to aeroelastic and aero-servo-elastic instabilities and uses flight testing for confirmation of the absence of such instabilities. Flight testing for flutter is accomplished by using specially instrumented programmed missiles, air or ground launched with a booster to reach the extreme flight conditions of tactical use, or by using guided missiles with telemetered performance data. The instrumentation and testing techniques are discussed along with the success of recent flight tests.

Kutschinski, C. R.↗
NASA NTRS1979

Unfolding the air vanes on a supersonic air-launched missile

ASALM (Advanced Strategic Air-Launched Missile) is a supersonic air vehicle designed to be air-launched from a carrier aircraft. The four aft aerodynamic control vanes are folded to maximize the number of missiles carried on-board. The unfolding (erection) system must be small, energetic, fast, and strong. The materials selected and problems that arose during development of the unfolding system are described.

Wohltmann, M.↗
NASA NTRS1983

Methane flux across the air-water interface - Air velocity effects

Methane loss to the atmosphere from flooded wetlands is influenced by the degree of supersaturation and wind stress at the water surface. Measurements in freshwater ponds in the St. Marks Wildlife Refuge, Florida, demonstrated that for the combined variability of CH4 concentrations in surface water and air velocity over the water surface, CH4 flux varied from 0.01 to 1.22 g/sq m/day. The liquid exchange coefficient for a two-layer model of the gas-liquid interface was calculated as 1.7 cm/h for CH4 at air velocity of zero and as 1.1 + 1.2 v to the 1.96th power cm/h for air velocities from 1.4 to 3.5 m/s and water temperatures of 20 C.

Sebacher, D. I.↗
NASA NTRS1985

Proton-air and proton-proton cross sections from air shower data

Data on the fluctuations in depth of maximum development of cosmic ray air showers, corrected for the effects of mixed primary composition and shower development fluctuations, yield values of the inelastic proton-air cross section for laboratory energies in the range 10 to the 8th power to 10 to the 10th power GeV. From these values of proton-air cross section, corresponding values of the proton-proton total cross section are derived by means of Glauber theory and geometrical scaling. The resulting values of proton-proton cross section are inconsistent with a well known 1n(2)s extrapolation of ISR data which is consistent with SPS data; they indicate a less rapid rate of increase in the interval 540 sq root of s 100000 GeV.

Linsley, J.↗
NASA NTRS1988

Effects of water-contaminated air on blowoff limits of opposed jet hydrogen-air diffusion flames

The effects of water-contaminated air on the extinction and flame restoration of the central portion of N2-diluted H2 versus air counterflow diffusion flames are investigated using a coaxial tubular opposed jet burner. The results show that the replacement of N2 contaminant in air by water on a mole for mole basis decreases the maximum sustainable H2 mass flow, just prior to extinction, of the flame. This result contrasts strongly with the analogous substitution of water for N2 in a relatively hot premixed H2-O2-N2 flame, which was shown by Koroll and Mulpuru (1986) to lead to a significant, kinetically controlled increase in laminar burning velocity.

Pellett, Gerald L.↗
NASA NTRS1988

Boundary layer warming by condensation - Air-sea interaction during an extreme cold air outbreak from the eastern coast of the United States

Studies on an intense cold air outbreak that took place after a cold air cyclogenesis on January 27, 1986 are reviewed. Particular attention is given to data obtained during a multiaircraft research mission carried out on January 28, 1986 as part of the Genesis of Atlantic Lows Experiment. It was found that condensation heating of the subcloud layer air was comparable to heating by turbulent flux divergence.

Grossman, Robert L.↗