Search NASA⌕ Search

SEARCH · Search NASA

Results for “Analysis and Methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Solidification Furnace for In Situ Observation of Bulk Transparent Systems and Image Analysis Methods

This paper aims to describe the experimental framework of the Directional Solidification Insert (DSI), installed onboard the International Space Station (ISS), dedicated to the in situ and real-time characterization of the dynamic selection of the solid-liquid interface morphology in bulk samples of transparent materials under diffusive growth conditions. The in situ observation of the solid-liquid interface is an invaluable tool for gaining knowledge on the time-evolution of the interface pattern because the initial morphological instability evolves nonlinearly and undergoes a reorganization process. The result of each experiment, characterized by the sample concentration, a thermal gradient and a pulling rate, is a large number of images. Interpretation of these images necessitates a robust identification of each cell/dendrite position and size during the entire solidification. Several image analysis methods have been developed to achieve this goal reliably despite varying contrast and noise levels, and are described in details. Typical solidification experiments are presented and the dynamics of the pattern formation are analyzed to illustrate the application of the image analysis methods.

Programming languages↗
NASA NTRS1985

Stress analysis method for a clearance fit bolt under bearing loads

In the present, simple analysis method for bolt hole clearance stresses in mechanically fastened joints, an inverse formulation is used with a finite element analysis. Conditions along the bolt hole contact arc are specified by displacement constraint equations. The method was applied to a single fastener clearance-fit joint with typical clearance values, for the cases of a rigid, frictionless bolt and a quasi-isotropic graphite/epoxy laminate. Results indicate that the contact arc, as well as the peak stresses around the hole (and their locations), were strongly influenced by the clearance. After a minor initial nonlinearity, peak stresses varied linearly with applied load. Clearance levels are found to have only a minor influence on overall joint stiffness.

Crews, J. H., Jr.↗
NASA NTRS1974

A viscous/potential flow interaction analysis method for multi-element infinite swept wings, volume 1

An analysis method and computer program have been developed for the calculation of the viscosity dependent aerodynamic characteristics of multi-element infinite swept wings in incompressible flow. The wing configuration consisting at the most of a slat, a main element and double slotted flap is represented in the method by a large number of panels. The inviscid pressure distribution about a given configuration in the normal chord direction is determined using a two dimensional potential flow program employing a vortex lattice technique. The boundary layer development over each individual element of the high lift configuration is determined using either integral or finite difference boundary layer techniques. A source distribution is then determined as a function of the calculated boundary layer displacement thickness and pressure distributions. This source distribution is included in the second calculation of the potential flow about the configuration. Once the solution has converged (usually after 2-5 iterations between the potential flow and boundary layer calculations) lift, drag, and pitching moments can be determined as functions of Reynolds number.

Dvorak, F. A.↗
NASA NTRS1992

The NASA/industry Design Analysis Methods for Vibrations (DAMVIBS) Program: A government overview

LaRC, under the Design Analysis Methods for Vibrations (DAMVIBS) Program, set out in 1984 to establish the technology base needed by the rotorcraft industry for developing an advanced finite-element-based dynamics design analysis capability for vibrations. Considerable work was performed by the industry participants in the program since that time. Because the DAMVIBS Program is being phased out, a government/industry assessment of the program was made to identify those accomplishments and contributions which may be ascribed to the program. The purpose is to provide an overview of the program and its accomplishments and contributions from the perspective of the government sponsoring organization.

Kvaternik, Raymond G.↗
NASA NTRS1986

Probabilistic structural analysis methods for critical SSME propulsion components

The development of a three-dimensional inelastic analysis methodology for the Space Shuttle main engine (SSME) structural components is described. The methodology is composed of: (1) composite load spectra, (2) probabilistic structural analysis methods, (3) the probabilistic finite element theory, and (4) probabilistic structural analysis. The progress in the development of generic probabilistic models for various individual loads which consist of a steady state load, a periodic load, a random load, and a spike, is discussed. The capabilities of the Numerical Evaluation of Stochastic Structures Under Stress finite element code designed for probabilistic structural analysis of the SSME are examined. Variation principles for formulation probabilistic finite elements and a structural analysis for evaluating the geometric and material properties tolerances on the structural response of turbopump blades are being designed.

Chamis, C. C.↗
NASA NTRS1986

Probabilistic structural analysis methods for space propulsion system components

The development of a three-dimensional inelastic analysis methodology for the Space Shuttle main engine (SSME) structural components is described. The methodology is composed of: (1) composite load spectra, (2) probabilistic structural analysis methods, (3) the probabilistic finite element theory, and (4) probabilistic structural analysis. The methodology has led to significant technical progress in several important aspects of probabilistic structural analysis. The program and accomplishments to date are summarized.

Chamis, C. C.↗
NASA NTRS1987

Probabilistic structural analysis methods for space propulsion system components

The development of a three-dimensional inelastic analysis methodology for the Space Shuttle main engine (SSME) structural components is described. The methodology is composed of: (1) composite load spectra, (2) probabilistic structural analysis methods, (3) the probabilistic finite element theory, and (4) probabilistic structural analysis. The methodology has led to significant technical progress in several important aspects of probabilistic structural analysis. The program and accomplishments to date are summarized.

Chamis, Christos C.↗
NASA NTRS1999

Development of Analysis Methods for Designing with Composites

The project involved the development of new analysis methods to achieve efficient design of composite structures. We developed a complex variational formulation to analyze the in-plane and bending coupling response of an unsymmetrically laminated plate with an elliptical cutout subjected to arbitrary edge loading as shown in Figure 1. This formulation utilizes four independent complex potentials that satisfy the coupled in-plane and bending equilibrium equations, thus eliminating the area integrals from the strain energy expression. The solution to a finite geometry laminate under arbitrary loading is obtained by minimizing the total potential energy function and solving for the unknown coefficients of the complex potentials. The validity of this approach is demonstrated by comparison with finite element analysis predictions for a laminate with an inclined elliptical cutout under bi-axial loading.The geometry and loading of this laminate with a lay-up of [-45/45] are shown in Figure 2. The deformed configuration shown in Figure 3 reflects the presence of bending-stretching coupling. The validity of the present method is established by comparing the out-of-plane deflections along the boundary of the elliptical cutout from the present approach with those of the finite element method. The comparison shown in Figure 4 indicates remarkable agreement. The details of this method are described in a manuscript by Madenci et al. (1998).

Madenci, E.↗
NASA NTRS2007

Structural Analysis Methods for Structural Health Management of Future Aerospace Vehicles

Two finite element based computational methods, Smoothing Element Analysis (SEA) and the inverse Finite Element Method (iFEM), are reviewed, and examples of their use for structural health monitoring are discussed. Due to their versatility, robustness, and computational efficiency, the methods are well suited for real-time structural health monitoring of future space vehicles, large space structures, and habitats. The methods may be effectively employed to enable real-time processing of sensing information, specifically for identifying three-dimensional deformed structural shapes as well as the internal loads. In addition, they may be used in conjunction with evolutionary algorithms to design optimally distributed sensors. These computational tools have demonstrated substantial promise for utilization in future Structural Health Management (SHM) systems.

Tessler, Alexander↗
NASA NTRS2019

Benchmarking Mixed Mode Failure in Progressive Damage and Failure Analysis Methods

The verification and validation of progressive-damage-analysis finite element methods are difficult but critical tasks to undertake during their development. Verification exercises assess whether a predictive analysis tool produces results that are consistent with the fundamental concepts and assumptions of the tool under evaluation. Ideally, closed-form analytical solutions can be derived for which method verification results can be compared. Problems selected for computational tool verification are often simple and isolate individual features of the tool. In the case of progressive damage finite element methods, verifications should be performed to evaluate the ability of the model to predict the initiation of damage and its growth through the finite element mesh under a variety of conditions. Mabson et al. proposed a test case of a unidirectional, fiber-reinforced plate with a center crack subjected to tensile loads to evaluate matrix crack propagation predictions. The problem was modeled using the Abaqus Hashin continuum damage mechanics (CDM) model for fiber-reinforced composites. Different combinations of matrix strengths and element sizes were used in the simulations, and the results were compared to a closed-form solution based on linear elastic fracture mechanics (LEFM). It was determined that the Abaqus CDM model could predict the LEFM solution of Mode I cracks only when the finite element mesh density met specific requirements based on the material properties. This paper presents closed-form LEFM solutions for a center notch mixed mode (CNMM) verification problem. Parametric finite element analyses were developed using progressive damage analysis methods of both the Discrete Damage Mechanics (DDM) and CDM classes. The progressive damage analysis methods applied in the analyses of the CNMM problem include CompDam and the Floating Node Method. Analyses were conducted with various mode mixities and element sizes to verify that the damage models were working as intended and to identify any limits of applicability.

Leone, Frank↗
NASA NTRSDate not supplied

Verification and Validation of Progressive Damage and Failure Analysis Methods for Intralaminar Failure Modes in Thermoplastic Composites

Current progressive damage and failure analysis (PDFA) methods were developed around thermoset material systems and their physical behavior. However, the applicability of these analysis methods has not been evaluated for use in modeling thermoplastic material systems. As part of the Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project sponsored by NASA, intralaminar failure characterization was completed on a thermoplastic material system, AS4D/PEKK-FC, with off-axis tension (OAT) and off-axis compression (OAC) testing. The experiments were able to capture matrix non-linear shear behavior and the failure envelope of the material system. Two PDFA methods, LS-DYNA MAT299 and NASA’s CompDam-DGD, were then employed to simulate individual coupon behavior and simulation results were compared to published verification and validation guidelines from the CMH-17 crashworthiness working group. The results found that the two modeling methods provided suitable representation of material behavior of thermoplastics.

PDFA↗
NASA NTRSDate not supplied

Verification and Validation of Progressive Damage and Failure Analysis Methods for Intralaminar Failure Modes in Thermoplastic Composites

Current progressive damage and failure analysis (PDFA) methods were developed around thermoset material systems and their physical behavior. However, the applicability of these analysis methods has not been evaluated for use in modeling thermoplastic material systems. As part of the Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project sponsored by NASA, intralaminar failure characterization was completed on a thermoplastic material system, AS4D/PEKK-FC, with off-axis tension (OAT) and off-axis compression (OAC) testing. The experiments were able to capture matrix non-linear shear behavior and the failure envelope of the material system. Two PDFA methods, LS-DYNA MAT299 and NASA’s CompDam-DGD, were then employed to simulate individual coupon behavior and simulation results were compared to published verification and validation guidelines from the CMH-17 crashworthiness working group. The results found that the two modeling methods provided suitable representation of material behavior of thermoplastics.

PDFA↗
NASA NTRS1993

The NASA/industry Design Analysis Methods for Vibrations (DAMVIBS) program: A government overview

NASA-Langley, under the Design Analysis Methods for Vibrations (DAMVIBS) Program, set out in 1984 to establish the technology base needed by the rotorcraft industry for developing an advanced finite-element-based dynamics design analysis capability for vibrations. Considerable work has been done by the industry participants in the program since that time. Because the DAMVIBS Program is being phased out, a government/industry assessment of the program has been made to identify those accomplishments and contributions which may be ascribed to the program. The purpose of this paper is to provide an overview of the program and its accomplishments and contributions from the perspective of the government sponsoring organization.

Kvaternik, Raymond G.↗
NASA NTRS2003

Analysis Method for Inelastic, Adhesively Bonded Joints with Anisotropic Adherends

A one-dimensional analysis method for evaluating adhesively bonded joints composed of anisotropic adherends and adhesives with nonlinear material behavior is presented in the proposed paper. The strain and resulting stress field in a general, bonded joint overlap are determined by using a variable-step, finite-difference solution algorithm to iteratively solve a system of first-order differential equations. Applied loading is given by a system of combined extensional, bending, and shear forces that are applied to the edge of the joint overlap. Adherends are assumed to behave as linear, cylindrically bent plates using classical laminated plate theory that includes the effects of first-order transverse shear deformation. Using the deformation theory of plasticity and a modified von-Mises yield criterion, inelastic material behavior is modeled in the adhesive layer. Results for the proposed method are verified against previous results from the literature and shown to be in excellent agreement. An additional case that highlights the effects of transverse shear deformation between similar adherends is also presented.

Smeltzer, Stanley S., III↗
NASA NTRS1992

The 3D inelastic analysis methods for hot section components

A two-year program to develop advanced 3D inelastic structural stress analysis methods and solution strategies for more accurate and cost effective analysis of combustors, turbine blades, and vanes is described. The approach was to develop a matrix of formulation elements and constitutive models. Three constitutive models were developed in conjunction with optimized iterating techniques, accelerators, and convergence criteria within a framework of dynamic time incrementing. Three formulation models were developed: an eight-noded midsurface shell element; a nine-noded midsurface shell element; and a twenty-noded isoparametric solid element. A separate computer program has been developed for each combination of constitutive model-formulation model. Each program provides a functional stand alone capability for performing cyclic nonlinear structural analysis. In addition, the analysis capabilities incorporated into each program can be abstracted in subroutine form for incorporation into other codes or to form new combinations.

Mcknight, R. L.↗