Search NASA⌕ Search

SEARCH · Search NASA

Results for “Atmospheric waves”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

The Strange Case of Ground-Coupled Airwaves on Seismoacoustic Stations at Local to Near-Regional Scales

Here we investigate the application of ground-coupled airwaves observed by seismoacoustic stations at local to near-regional scales to detect signals of interest and determine back-azimuth information. Ground-coupled airwaves are created from incident pressure waves traveling through the atmosphere that couple to the earth and transmit as a seismic wave with retrograde elliptical motion. Previous studies at sub-local scales (<10 km from a source of interest) found the back-azimuth to the source could be accurately determined from seismoacoustic signals recorded by acoustic and 3-component seismic sensors spatially separated on the order of 10 to 150 m. The potential back-azimuth directions are estimated from the coherent signals between the acoustic and vertical seismic data, via a propagation-induced phase shift of the seismoacoustic signal. A unique solution is then informed by the particle motion of the 3-component seismic station, which was previously found to be less accurate than the seismoacoustic-sensor method. We investigate the applicability of this technique to greater source-receiver distances, from 50-100 km and up to 400 km, which contains pressure waves with tropospheric and stratospheric ray paths, respectively. Specifically, we analyze seismoacoustic sources with ground truth from rocket motor fuel elimination events at the Utah Test and Training Range (UTTR) as well as a 2020 rocket launch in Southern California. From these sources we observe evidence that while coherent signals can be seen from both sources on multiple seismoacoustic station pairs, the determined ground-coupled airwave back-azimuths are more complicated than results at more local scales. Our findings suggest more complex factors including incidence angle, coupling location, subsurface material, and atmospheric propagation effects need to be fully investigated before the ground-coupled airwave back-azimuth determination method can be applied or assessed at these further distances.

58 GEOSCIENCES↗
DOE OSTI2023

A mountain-induced moist baroclinic wave test case for the dynamical cores of atmospheric general circulation models

Idealized test cases for the dynamical cores of atmospheric general circulation models are informative tools to assess the accuracy of the numerical designs and investigate the general characteristics of atmospheric motions. A new test case is introduced that is built upon a baroclinically unstable base state with an added orographic barrier. The topography is analytically prescribed and acts as a trigger of both baroclinic Rossby waves and inertia–gravity waves on a rotating, regular-sized planet. Both dry and idealized moist configurations are suggested. The latter utilizes the Kessler warm-rain precipitation scheme. The test case enhances the complexity of the existing test suite hierarchy and focuses on the impacts of two midlatitudinal mountain ridges on the circulation. Selected simulation examples from four dynamical cores are shown. These are the Spectral Element and Finite Volume dynamical cores, which are part of the National Center for Atmospheric Research (NCAR) Community Earth System Model (CESM), versions 2.1.3 and 2.2, and the Cubed-Sphere Finite Volume dynamical cores, which is new to CESM version 2.2. In addition, the Model for Prediction Across Scales (MPAS) is tested. The overall flow patterns agree well in the four dynamical cores, but the details can vary greatly. The examples highlight the broad palette of use cases for the test case and reveal physics–dynamics coupling issues.

58 GEOSCIENCES↗
DOE OSTI2024

Forecasting Tropical Annual Maximum Wet-Bulb Temperatures Months in Advance From the Current State of ENSO

Humid heatwaves, characterized by high temperature and humidity combinations, challenge tropical societies. Extreme wet-bulb temperatures (TW) over tropical land are coupled to the warmest sea surface temperatures by atmospheric convection and wave dynamics. Here, we harness this coupling for seasonal forecasts of the annual maximum of daily maximum TW (TW max ). We develop a multiple linear regression model that explains 80% of variance in tropical mean TW max and significant regional TW max variances. The model considers warming trends and El Niño and Southern Oscillation indices. Looking ahead, the strong-to-very-strong El Niño at the end of 2023, with an Oceanic Niño Index of ~2.0, suggests a 2024 tropical land mean TW max of 26.2°C (25.9–26.4°C), and a 68% chance (24%–94%) of breaking existing records. This method also predicts regional TW max in specific areas.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Electrocatalytic properties of a novel ruthenium( ii ) terpyridine-based complex towards CO 2 reduction

The electrocatalytic properties of Ru complexes are of great technological interest given their potential application in reactions such water splitting and CO 2 reduction. In this work, a novel terpyridine-based Ru(II) complex, [RuCl(trpy)(acpy)], trpy = 2,2':6',2"-terpyridine, acpy - = 2-pyridylacetate was synthesized and its spectroscopic, electrochemical and catalytic properties were explored in detail. In dry acetonitrile, the complex exhibits two reduction peaks at -1.95 V and -2.20 V vs. Fc/Fc + , attributed to consecutive 1 e - reduction. Under CO 2 atmosphere, a catalytic wave is observed (E onset = 2.1 V vs. Fc/Fc + ), with CO as the main reduction product. Bulk electrolysis reveals a turnover number (TON) of 12 (k obs = 1.5 s -1 ). In the presence of 1% water, an improvement in the catalytic activity is observed (TON CO = 21 and k obs = 2.0 s -1 ) and, additionally, formate was also detected (TON HCOO = 7). Spectroelectrochemical experiments allowed the identification of a metallocarboxylate (Ru–COO - ) intermediate under anhydrous conditions, while in water, the partial labilization of the acpy- ligand was observed in the course of the catalytic cycle. The experimental data was combined with DFT calculations, allowing the proposal of a catalytic cycle. Here the results establish important relationships between selectivity, ligand structure and reaction conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Seismoacoustic Explosion Yield and Depth Estimation: Insights from the Large Surface Explosion Coupling Experiment

The Large Surface Explosion Coupling Experiment (LSECE) is a chemical explosion experiment conducted in Yucca Flat at the Nevada National Security Site in 2020. The experiment included two surface detonations of ~1000 kg trinitrotoluene equivalent. The main goal of this experiment was to provide the ground-truth data for seismoacoustic wave excitation by large chemical explosions near the ground surface. The seismic and acoustic energy partitioning between the surface is strongly governed by the depth or height of explosions, and either seismic or acoustic-only analysis may have inherent ambiguity in determining explosion yield and depth simultaneously. Previous studies suggested that joint seismoacoustic analysis can resolve the trade-off and reduce the uncertainty of yield and depth estimation dramatically. Here we demonstrate the capability of seismoacoustic analysis to improve the accuracy of explosion yield and depth estimation with the LSECE data. Local acoustic wave propagation in the atmosphere can be substantially affected by constantly varying weather conditions. Consisting of two detonations before dawn and in the afternoon, LSECE provides unique data to evaluate the model accuracy of acoustic wave propagation and seismoacoustic energy partitioning depending on local atmospheric conditions. We quantitatively evaluate the accuracy of yield and depth estimation depending on atmospheric variability and the improvement achieved by the joint seismoacoustic approach.

58 GEOSCIENCES↗
DOE OSTI2024

Assessing Impacts of Waves on Hub-Height Winds off the U.S. West Coast Using Lidar Buoys and Coupled Modeling Approaches

Given the importance of offshore wind energy development to the U.S. clean energy targets, it is vital to be able to characterize the wind resource in that environment accurately. Toward that end, two Bureau of Ocean Energy Management buoys equipped with Doppler lidar are being maintained by Pacific Northwest National Laboratory on behalf of the Department of Energy and deployed to regions of potential offshore wind development. In addition to standard meteorological and oceanographic measurements, the buoys document the wind profile between about 40 m and 250 m above the sea surface through Doppler lidar retrievals. After a multiyear deployment of two buoys along the U.S. East Coast, the buoys were redeployed to the U.S. West coast from 2020 – 2022 to locations near the Humboldt and Morro Bay lease areas. The buoys provide nearly continuous, multiyear datasets that can be used to evaluate predictions of hub-height (~100 m) wind speed for standard atmospheric models in the region. In the absence of measurements at the study site, offshore wind developers rely on model-based data to assess site conditions. Potential sources of model error in this environment include under-resolution or misrepresentation of coastal topographically forced flows, marine boundary layer dynamics and the evolution of their associated cloud and turbulence fields, the role of upwelling and other currents on surface heat fluxes into the boundary layer, and the impact of wave fields on surface momentum fluxes and thus the wind speed profile. In particular, most predictive models of wind speed do not predict wave fields at all, relying on parameterizations to represent their effects. In thus study, we focus on evaluating the role of wind / wave interactions on modeled hub-height wind speed and error by using the Coupled Ocean–Atmosphere–Wave–Sediment–Transport Modeling System to capture two-way interactions between an atmospheric model (Weather Research and Forecasting (WRF)) and a wave model (WAVEWATCHIII (WW3)) and compare to both stand-alone WRF and one-way coupled WRF / WW3 configurations. Our approach is similar to that used in Gaudet et al. (2022) to evaluate wind / wave coupling over the U.S. East Coast, but applied to the very different environment of the U.S. West Coast. We show examples for two cases, a cold-season frontal case and a warm-season low-level jet case. We find that wind / wave coupling makes little impact on model error for these cases at the location of the lidar buoys, for which other misrepresentations of model physics seems to be responsible for model-observation discrepancies. However, domain-wide evaluations, which also make use of the National Buoy Data Center network, show that a two-way coupling approach is less prone to systematic errors in the hub-height wind field than the one-way coupled approach. WRF resolution of kilometer-scale or less is needed to properly capture the sharp wind speed gradients that can be found along the coastline, and WW3 simulations driven by the downscaled WRF produce better bulk and spectral wave fields when compared to observations. Implications of the results for wind resource characterization are then discussed.

17 WIND ENERGY↗
DOE OSTI2020

Peculiarities of adaptive phase correction of optical wave distortions under conditions of ‘strong’ intensity fluctuations

The reason for the loss of efficiency of adaptive phase correction in the propagation of optical waves in a turbulent atmosphere under conditions of ‘strong’ intensity fluctuations is experimentally explained for the first time. Based on the data from experiments conducted on both horizontal and vertical atmospheric paths, we have found that intensity fluctuations begin to significantly affect phase measurements when the coherence radius of the optical wave becomes less than the radius of the first Fresnel zone. Under these conditions, the main meter of adaptive optics systems, i. e. the Hartmann sensor, no longer provides correct measurements of the phase distribution in the presence of deep amplitude modulation. Based on the study of the behaviour of the mode components of the phase fluctuations reconstructed from the results of measurements in various operating regimes, we have found that, first of all, the amplitudes of the lowest modes of phase fluctuation expansion (tilts, defocusing, and astigmatism) are distorted, which, as the analysis shows, is very different from the regime of weak fluctuations. (atmospheric optics)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

A Study on Modeled Wind Speed Errors Using the U.S. Department of Energy Buoys

Pacific Northwest National Laboratory (PNNL) operates two AXYS WindSentinel lidar buoys for the U.S. Department of Energy’s Wind Energy Technologies Office. The purpose of these buoys is to collect hub-height winds and supporting meteorological and oceanographic information to facilitate the development of wind energy in the U.S. waters. The first deployment for one buoy was off the coast of Virginia from December 2014 to May 2016, and the first deployment for the other buoy was off the coast of New Jersey from November 2015 until February 2017. This report describes recent analysis of data collected during these first two deployments. Specifically, we compare hub-height wind speed estimates using Monin-Obukhov Similarity Theory (MOST) to the lidar measurements, and examine how those errors are affected by wind direction, atmospheric stability, wind-wave direction differences, and various measures of the wave-state. The comparisons are done using standard similarity functions based on MOST; including the Businger - Dyer, the Beljaars & Holtslag and the Vickers & Mahrt similarity functions. All models produce large errors over the range of atmospheric stabilities that were observed, with the largest errors occurring for stable flows. The Vickers & Mahrt function resulted in the largest overall bias and standard deviation, while Beljaars & Holtslag function gave the smallest bias and standard deviation due to its better performance under stable conditions. The models perform best under unstable conditions, but even in this regime there is a consistent overestimation of the wind speed of between roughly 0 to 1 ms -1 compared to the lidar measurements. We identify specific metocean conditions (i.e. stability and wind and wave directions) at each of the deployment locations that lead to large errors in MOST predictions. Finally, a coupled ocean-atmosphere model framework was investigated to simulate large errors in weather research forecasting (WRF).

17 WIND ENERGY↗
DOE OSTI2023

Resolved Gravity Waves in the Extratropical Stratosphere: Effect of Horizontal Resolution Increase from O (10) to O (1) km

Global ECMWF IFS simulations with horizontal grid spacings of 1, 4, and 9 km are used to assess gravity wave forcing (GWF) in the extratropical stratosphere. Results with important implications for GWF parameterizations at high and intermediate resolutions are presented. A doubling in the zonal-mean resolved GWF is observed when the horizontal resolution is increased from 9 to 1 km. Small-scale gravity waves with horizontal wavelengths < 100 km dominate this increase. Over most regions, excluding the polar night jet in the Antarctic spring, the total (resolved + parameterized) GWF at 9 km (4 km) is underestimated by up to 30% (15%). This implies that the parameterization of GWF is still required at 9 and 4 km horizontal resolutions. Despite the small land area in the Southern Hemisphere (SH), the resolved orographic and nonorographic GWF contribute equally to the total GWF in the SH at 1 km resolution. This is not reflected in the partitioning of the parameterized GWF, which has a significantly larger nonorographic contribution at 9 km. As a result, a zonal-mean momentum budget analysis reveals that the total GWF contributes one-third of SH springtime polar vortex deceleration at 1 km, whereas the contribution is as much as 50% at 9 km. In conclusion, this suggests that a rebalancing of the parameterized nonorographic and orographic GWF is required.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Using sub-limb observations to measure gravity waves excited by convection

Convective gravity waves are a major driver of atmospheric circulation, including the stratospheric and mesospheric quasi-biennial oscillation (QBO) and the Brewer–Dobson circulation. Previous work shows clear evidence that these waves can be excited by both single convective cells and by mesoscale convective complexes acting as a single unit. However, the partitioning of the generated waves and, crucially for atmospheric model development, the flux of momentum they transport between these two types of excitation process remains highly uncertain due to a fundamental lack of suitable observations at the global scale. Here, we use both theoretical calculations and sampled output from a high-resolution weather model to demonstrate that a satellite instrument using a sub-limb geometry would be well suited to characterising the short-vertical short-horizontal gravity waves these systems produce, and hence to provide the scientific knowledge needed to identify the relative wave-driving contribution of these two types of convective wave excitation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Atmospheric Structure Prediction for Infrasound Propagation Modeling Using Deep Learning

Abstract Infrasound is generated by a variety of natural and anthropogenic sources. Infrasonic waves travel through the dynamic atmosphere, which can change on the order of minutes to hours. Infrasound propagation largely depends on the wind and temperature structure of the atmosphere. Numerical weather prediction models are available to provide atmospheric specifications, but uncertainties in these models exist and they are computationally expensive to run. Machine learning has proven useful in predicting tropospheric weather using Long Short‐Term Memory (LSTM) networks. An LSTM network is utilized to make atmospheric specification predictions up to ∼30 km for three different training and testing scenarios: (a) the model is trained and tested using only radiosonde data from the Albuquerque, NM, USA station, (b) the model is trained on radiosonde stations across the contiguous US, excluding the Albuquerque, NM, USA station, which was reserved for testing, and (c) the model is trained and tested on radiosonde stations across the contiguous US. Long Short‐Term Memory predictions are compared to a state‐of‐the‐art reanalysis model and show cases where the LSTM outperforms, performs equally as well, or underperforms in comparison to the state‐of‐the‐art. Regional and temporal trends in model performance across the US are also discussed. Results suggest that the LSTM model is a viable tool for predicting atmospheric specifications for infrasound propagation modeling.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Estimation of mean electron energy in helium surface ionization waves on dielectric substrates

Abstract The determination of basic plasma parameters in atmospheric pressure discharges is critical to advancing their use in applications. Atmospheric pressure plasma jets have found use in the fields of medicine, agriculture, material modification and others. Atmospheric pressure plasma jets often generate plasma surface ionization waves (SIW) which interact with and propagate over surfaces. Electrical diagnostics are challenging in SIW due to high collision frequencies and small scale of the plasma discharge. This work employs a passive optical emission line ratio technique to estimate the mean electron energy in SIW over planar dielectric substrates. The method uses an intensity ratio of two helium triplet lines: He( 3 3 S ) at 706.5 nm and He( 3 3 D ) at 587.56 nm. A collisional-radiative model is used to correlate line ratio to mean electron energy and determine dependencies on electron density and He/air gas mixture. Mean electron energies ranging from 3–8 eV are determined in He/air mixtures and are found to remain constant as the surface wave propagates radially. This work provides a 2D, time-resolved, mean electron energy diagnostic for surface ionization wave propagation and validation of numerical modeling in atmospheric pressure systems with spatially varying He/air gas mixtures. The model in question is designed for use with any He line ratio in the n = 3 excitation level.

Morsell, Joshua (ORCID:0000000331073002)↗
DOE OSTI2021

The First Detection of an Earthquake From a Balloon Using Its Acoustic Signature

Extreme temperature and pressure conditions on the surface of Venus present formidable technological challenges against performing ground-based seismology. Efficient coupling between the Venusian atmosphere and the solid planet theoretically allows the study of seismically generated acoustic waves using balloons in the upper atmosphere, where conditions are far more clement. However, earthquake detection from a balloon has never been demonstrated. We present the first detection of an earthquake from a balloon-borne microbarometer near Ridgecrest, CA in July 2019 and include a detailed analysis of the dependence of seismic infrasound, as measured from a balloon on earthquake source parameters, topography, and crustal and atmospheric structure. Our comprehensive analysis of seismo-acoustic phenomenology demonstrates that seismic activity is detectable from a high-altitude platform on Earth, and that Rayleigh wave-induced infrasound can be used to constrain subsurface velocities, paving the way for the detection and characterization of such signals on Venus.

58 GEOSCIENCES↗
DOE OSTI2022

Urbanization Impact on Regional Climate and Extreme Weather: Current Understanding, Uncertainties, and Future Research Directions

Abstract Urban environments lie at the confluence of social, cultural, and economic activities and have unique biophysical characteristics due to continued infrastructure development that generally replaces natural landscapes with built-up structures. The vast majority of studies on urban perturbation of local weather and climate have been centered on the urban heat island (UHI) effect, referring to the higher temperature in cities compared to their natural surroundings. Besides the UHI effect and heat waves, urbanization also impacts atmospheric moisture, wind, boundary layer structure, cloud formation, dispersion of air pollutants, precipitation, and storms. In this review article, we first introduce the datasets and methods used in studying urban areas and their impacts through both observation and modeling and then summarize the scientific insights on the impact of urbanization on various aspects of regional climate and extreme weather based on more than 500 studies. We also highlight the major research gaps and challenges in our understanding of the impacts of urbanization and provide our perspective and recommendations for future research priorities and directions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Dynamically downscaled seasonal heat wave projections in the CONUS

Heat waves are a well-documented hazard that are projected to increase in intensity, duration, and frequency with climate change. Regions of the US experience widely varying temperatures; for example, 35 °C is extremely hot for spring in the Northeast but not for summer in the Southeast. It is important to evaluate projections within a regional context and at a high enough resolution to understand the risks to populations. We identify heat waves across the Conterminous US (CONUS) under SSP5–8.5 from 2020 to 2059 with an ensemble of dynamically downscaled Coupled Model Intercomparison Project Phase 6 (CMIP6) model outputs. We demonstrate that there are regional differences caused by seasonal and local drivers of persistent hot temperatures. Summer heat waves are increasing in intensity and duration faster than winter heat waves because of the atmospheric conditions that promote these events. Our analysis emphasizes the value of fine-resolution modeling for projecting future climate risks.

Rubin, Hannah [University of Tennessee, Knoxville ↗
DOE OSTI2025

User Guide: A Curated Dataset of Regional Meteor Events with Simultaneous Optical and Infrasound Observations

This user guide supports a curated dataset of 71 meteor events recorded between 2006 and 2011 in Southwestern Ontario, Canada. Each event was simultaneously observed by ground-based optical cameras and an infrasound array, providing a rare opportunity to examine meteor trajectories and acoustic signals from the same atmospheric entry events. The dataset includes raw and processed optical data, meteor trajectories, photometric light curves, infrasound waveforms, and atmospheric specifications relevant for acoustic modeling. The archive is structured to support reproducible research in meteor physics, atmospheric acoustics, and shock wave analysis. It is organized following transparent file naming conventions and structured folders to facilitate scientific reuse, comparison, and integration across research domains. The dataset is freely available on Zenodo, doi: 10.5281/zenodo.15868512.

54 ENVIRONMENTAL SCIENCES↗