SEARCH · Search NASA

Results for “Autonomous Experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

Cislunar Autonomous Positioning System Technology Operations and Navigation Experiment (CAPSTONE): Pathfinder for Artemis Gateway

The Cislunar Autonomous Positioning System Technology Operations and Navigation Experiment (CAPSTONE) mission was developed by NASA in collaboration with Advanced Space, LLC of Westminster, Colorado. This technology demonstration mission serves as a pathfinder for near rectilinear halo orbit (NHRO) operations around the Moon. The NHRO, (Perilune = 3,200 km; Apolune = 70,000 km) is the intended orbit for NASA’s Artemis Gateway, a small, human-tended space station planned for lunar orbit. The CAPSTONE mission will validate simulations and confirm operational planning for Gateway while also validating performance of navigation and stationkeeping requirements for Gateway’s Power and Propulsion Element. Therefore, this mission will provide operational experience to NASA, commercial, and international missions for operations in a demanding orbital regime. This presentation accompanies the paper of the same title.

Elwood F Agasid↗

NASA NTRS1997

Feasibility Study For A Spaceborne Ozone/Aerosol Lidar System

Because ozone provides a shield against harmful ultraviolet radiation, determines the temperature profile in the stratosphere, plays important roles in tropospheric chemistry and climate, and is a health risk near the surface, changes in natural ozone layers at different altitudes and their global impact are being intensively researched. Global ozone coverage is currently provided by passive optical and microwave satellite sensors that cannot deliver high spatial resolution measurements and have particular limitations in the troposphere. Vertical profiling DIfferential Absorption Lidars (DIAL) have shown excellent range-resolved capabilities, but these systems have been large, inefficient, and have required continuous technical attention for long term operations. Recently, successful, autonomous DIAL measurements have been performed from a high-altitude aircraft (LASE - Lidar Atmospheric Sensing Experiment), and a space-qualified aerosol lidar system (LITE - Laser In-space Technology Experiment) has performed well on Shuttle. Based on the above successes, NASA and the Canadian Space Agency are jointly studying the feasibility of developing ORACLE (Ozone Research with Advanced Cooperative Lidar Experiments), an autonomously operated, compact DIAL instrument to be placed in orbit using a Pegasus class launch vehicle.

Campbell, Richard E.↗

NASA NTRS2005

An Expert System for Autonomous Spacecraft Control

The Autonomous Sciencecraft Experiment (ASE), part of the New Millennium Space Technology 6 Project, is flying onboard the Earth Orbiter 1 (EO-1) mission. The ASE software enables EO-1 to autonomously detect and respond to science events such as: volcanic activity, flooding, and water freeze/thaw. ASE uses classification algorithms to analyze imagery onboard to detect chang-e and science events. Detection of these events is then used to trigger follow-up imagery. Onboard mission planning software then develops a response plan that accounts for target visibility and operations constraints. This plan is then executed using a task execution system that can deal with run-time anomalies. In this paper we describe the autonomy flight software and how it enables a new paradigm of autonomous science and mission operations. We will also describe the current experiment status and future plans.

utonomy flight software↗

NASA NTRS2005

Lessons Learned in the Livingstone 2 on Earth Observing One Flight Experiment

The Livingstone 2 (L2) model-based diagnosis software is a reusable diagnostic tool for monitoring complex systems. In 2004, L2 was integrated with the JPL Autonomous Sciencecraft Experiment (ASE) and deployed on-board Goddard's Earth Observing One (EO-1) remote sensing satellite, to monitor and diagnose the EO-1 space science instruments and imaging sequence. This paper reports on lessons learned from this flight experiment. The goals for this experiment, including validation of minimum success criteria and of a series of diagnostic scenarios, have all been successfully net. Long-term operations in space are on-going, as a test of the maturity of the system, with L2 performance remaining flawless. L2 has demonstrated the ability to track the state of the system during nominal operations, detect simulated abnormalities in operations and isolate failures to their root cause fault. Specific advances demonstrated include diagnosis of ambiguity groups rather than a single fault candidate; hypothesis revision given new sensor evidence about the state of the system; and the capability to check for faults in a dynamic system without having to wait until the system is quiescent. The major benefits of this advanced health management technology are to increase mission duration and reliability through intelligent fault protection, and robust autonomous operations with reduced dependency on supervisory operations from Earth. The work-load for operators will be reduced by telemetry of processed state-of-health information rather than raw data. The long-term vision is that of making diagnosis available to the onboard planner or executive, allowing autonomy software to re-plan in order to work around known component failures. For a system that is expected to evolve substantially over its lifetime, as for the International Space Station, the model-based approach has definite advantages over rule-based expert systems and limit-checking fault protection systems, as these do not scale well. The model-based approach facilitates reuse of the L2 diagnostic software; only the model of the system to be diagnosed and telemetry monitoring software has to be rebuilt for a new system or expanded for a growing system. The hierarchical L2 model supports modularity and expendability, and as such is suitable solution for integrated system health management as envisioned for systems-of-systems.

Hayden, Sandra C.↗

DOE OSTI2025

Development of Predictive Models for Advanced Reactor Autonomous Control

Advanced reactor designs including microreactors and small modular reactors will contribute to the clean production of cheap energy, and autonomous control for advanced reactors is an appealing option for reducing cost. However, there is a lack of industry experience applying autonomous control for advanced nuclear reactors. To accelerate the development and industry acceptance of autonomous control software for nuclear reactors, we aim to demonstrate autonomous control of the Purdue University research reactor (PUR-1) using INL-developed model predictive control (MPC) methods. To prepare for this demonstration, data-driven predictive models based on process data collected from PUR-1 have been developed and integrated with MPC and used to control a physics-based model of PUR-1. A data-driven dynamics model and a gated recurrent unit (GRU) network were both trained on process data from PUR-1. The dynamics model was shown to effectively control the reactor model with MPC when provided reactivity as a control variable but failed to control the model through the control rod positions. The GRU network produced more accurate predictions than the dynamics model when evaluated on operational data, and future work will include the evaluation of the GRU network in the controller.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1995

Advanced flight experiment automation development

NASA's space science program suffers under operational constraints that severely limit scientific reactivity. We describe a possible extension to an existing system that enables space science to be conducted in a more reactive manner through advanced automation techniques that have recently been used in the Space Transportation System (STS)-based Spacelab. This automation allows sophisticated autonomous control of the experiment by monitoring and dynamically controlling the progress of the experiment protocol. This new approach permits intelligent conduct of experimental research investigations whether or not the crew is available or contact with the ground is possible. We describe an intelligent software assistant that can manage the conduct of the experiment autonomously, by providing responsive telepresence science, or by assisting the astronaut operator with scientific advice. The crew could be unavailable for short periods when the experiment has low priority, or for longer periods on partially tended Space Station. We suggest this system could be developed as a ground prototype using commercial hardware, versions of which have been flight qualified, in order to provide a natural transition path towards flight use. In order to make this demonstration most valuable, we propose not to select a particular Life Sciences experiment, but to include an experiment simulator representative of major scientific domains.

Groleau, Nicolas↗

NASA NTRS2005

Lunar and Planetary Science XXXVI, Part 4

Contents include the following: High-Resolution Electron Energy-Loss Spectroscopy (HREELS) Using a Monochromated TEM/STEM. Dynamical Evolution of Planets in Open Clusters. Experimental Petrology of the Basaltic Shergottite Yamato 980459: Implications for the Thermal Structure of the Martian Mantle. Cryogenic Reflectance Spectroscopy of Highly Hydrated Sulfur-bearing Salts. Implications for Core Formation of the Earth from High Pressure-Temperature Au Partitioning Experiments. Uranium-Thorium Cosmochronology. Protracted Core Differentiation in Asteroids from 182Hf-182W Systematics in the Eagle Station Pallasite. Maximizing Mission Science Return Through Use of Spacecraft Autonomy: Active Volcanism and the Autonomous Sciencecraft Experiment. Classification of Volcanic Eruptions on Io and Earth Using Low-Resolution Remote Sensing Data. Isotopic Mass Fractionation Laws and the Initial Solar System (sup26)Al/(sup27)Al Ratio. Catastrophic Disruption of Porous and Solid Ice Bodies (sup187)Re-(sup187)Os Isotope Disturbance in LaPaz Mare Basalt Meteorites. Comparative Petrology and Geochemistry of the LaPaz Mare Basalt Meteorites. A Comparison of the Structure and Bonding of Carbon in Apex Chert Kerogenous Material and Fischer-Tropsch-Type Carbons. Broad Spectrum Characterization of Returned Samples: Orientation Constraints of Small Samples on X-Ray and Other Spectroscopies. Apollo 14 High-Ti Picritic Glass: Oxidation/Reduction by Condensation of Alkali Metals. New Lunar Meteorites from Oman: Dhofar 925, 960 and 961. The First Six Months of Iapetus Observations by the Cassini ISS Camera. First Imaging Results from the Iapetus B/C Flyby of the Cassini Spacecraft. Radiative Transfer Calculations for the Atmosphere of Mars in the 200-900 nm Range. Geomorphologic Map of the Atlantis Basin, Terra Sirenum, Mars. The Meaning of Iron 60: A Nearby Supernova Injected Short-lived Radionuclides into Our Protoplanetary Disk.

Source record↗

NASA NTRS2004

Advanced Diagnostic System on Earth Observing One

In this infusion experiment, the Livingstone 2 (L2) model-based diagnosis engine, developed by the Computational Sciences division at NASA Ames Research Center, has been uploaded to the Earth Observing One (EO-1) satellite. L2 is integrated with the Autonomous Sciencecraft Experiment (ASE) which provides an on-board planning capability and a software bridge to the spacecraft's 1773 data bus. Using a model of the spacecraft subsystems, L2 predicts nominal state transitions initiated by control commands, monitors the spacecraft sensors, and, in the case of failure, isolates the fault based on the discrepant observations. Fault detection and isolation is done by determining a set of component modes, including most likely failures, which satisfy the current observations. All mode transitions and diagnoses are telemetered to the ground for analysis. The initial L2 model is scoped to EO-1's imaging instruments and solid state recorder. Diagnostic scenarios for EO-1's nominal imaging timeline are demonstrated by injecting simulated faults on-board the spacecraft. The solid state recorder stores the science images and also hosts: the experiment software. The main objective of the experiment is to mature the L2 technology to Technology Readiness Level (TRL) 7. Experiment results are presented, as well as a discussion of the challenging technical issues encountered. Future extensions may explore coordination with the planner, and model-based ground operations.

Hayden, Sandra C.↗

NASA NTRS2004

Autonomous Vegetation Cover Scene Classification of EO-1 Hyperion Hyperspectral Data

The Autonomous Sciencecraft Experiment (ASE) is a JPL-led, New Millennium Program mission containing new technology in the form of software to be flown on the Earth Observer-1 (EO-1) satellite in early 2004. This new technology will facilitate an artificially intelligent machine with autonomous science-driven capabilities. Among the ASE flight software is a set of onboard science algorithms designed for autonomous data processing, primarily based on change detection from observation to observation. Using the output from these algorithms, ASE has the ability to autonomously modify the EO-1 observation plan, retargeting itself for a more in-depth observation of a scientific event in progress. Furthermore, intelligent and selective information down-linking will maximize return of the most valuable scientific data. Among the algorithms developed for use on ASE is a Lava-Vegetation (L-V) detection algorithm. This algorithm can effectively identify the initial location and extent of lava and vegetation coverage based on spectral shape. Comparison of several different observations, all classified via this algorithm, can make change detection possible.

Lee, R. J.↗

NASA NTRS1995

Inflight resistance measurement on high-T(sub c) superconducting thin films exposed to orbital atomic oxygen on CONCAP-2 (STS-46)

In 1992, UAH (University of Alabama in Huntsville) conducted a unique experiment on STS-46 in which YBa2Cu3O7 (commonly known as '1-2-3' superconductor) high-T(c) superconducting thin film samples prepared at three different laboratories were exposed to 5 eV atomic oxygen in low Earth orbit on the ambient and 320 C hot plate during the first flight of the CONCAP-2 (Complex Autonomous Payload) experiment carrier. The resistance of the thin films was measured in flight during the atomic oxygen exposure and heating cycle. Superconducting properties were measured in the laboratory before and after the flight by the individual experimenters. Films with good superconducting properties, and which were exposed to the oxygen flux, survived the flight including those heated to 320 C (600 K) with properties essentially unchanged, while other samples which were heated but not exposed to oxygen were degraded. The properties of other flight controls held at ambient temperature appear unchanged and indistinguishable from those of ground controls, whether exposed to oxygen or not.

Gregory, J. C.↗

NASA NTRS2002

Autonomous planning and scheduling on the TechSat 21 mission

The Autonomous Sciencecraft Experiment (ASE) will fly onboard the Air Force TechSat 21 constellation of three spacecraft scheduled for launch in 2006. ASE uses onboard continuous planning, robust task and goal-based execution, model-based mode identification and reconfiguration, and onboard machine learning and pattern recognition to radically increase science return by enabling intelligent downlink selection and autonomous retargeting.

AI architectures applications intelligent agents m↗

NASA NTRS2005

New millennium program ST6: autonomous technologies for future NASA spacecraft

The purpose of NASA's New Millennium Program (NMP) is to validate advanced technologies in space and thus lower the risk for the first mission user. The focus of NMP is only on those technologies which need space environment for proper validation. The ST6 project has developed two advanced, experimental technologies for use on spacecraft of the future. These technologies are the Autonomous Sciencecraft Experiment and the Inertial Stellar Compass. These technologies will improve spacecraft's ability to: make decisions on what information to gather and send back to the ground, determine its own attitude and adjust its pointing.

ST6↗

NASA NTRS1991

Reusable Reentry Satellite (RRS) system design study

The Reusable Reentry Satellite (RRS) is intended to provide investigators in several biological disciplines with a relatively inexpensive method to access space for up to 60 days with eventual recovery on Earth. The RRS will permit totally intact, relatively soft, recovery of the vehicle, system refurbishment, and reflight with new and varied payloads. The RRS is to be capable of three reflights per year over a 10-year program lifetime. The RRS vehicle will have a large and readily accessible volume near the vehicle center of gravity for the Payload Module (PM) containing the experiment hardware. The vehicle is configured to permit the experimenter late access to the PM prior to launch and rapid access following recovery. The RRS will operate in one of two modes: (1) as a free-flying spacecraft in orbit, and will be allowed to drift in attitude to provide an acceleration environment of less than 10(exp -5) g. the acceleration environment during orbital trim maneuvers will be less than 10(exp -3) g; and (2) as an artificial gravity system which spins at controlled rates to provide an artificial gravity of up to 1.5 Earth g. The RRS system will be designed to be rugged, easily maintained, and economically refurbishable for the next flight. Some systems may be designed to be replaced rather than refurbished, if cost effective and capable of meeting the specified turnaround time. The minimum time between recovery and reflight will be approximately 60 days. The PMs will be designed to be relatively autonomous, with experiments that require few commands and limited telemetry. Mass data storage will be accommodated in the PM. The hardware development and implementation phase is currently expected to start in 1991 with a first launch in late 1993.

Source record↗

DOE OSTI2024

Targeted materials discovery using Bayesian algorithm execution

Rapid discovery and synthesis of future materials requires intelligent data acquisition strategies to navigate large design spaces. A popular strategy is Bayesian optimization, which aims to find candidates that maximize material properties; however, materials design often requires finding specific subsets of the design space which meet more complex or specialized goals. We present a framework that captures experimental goals through straightforward user-defined filtering algorithms. These algorithms are automatically translated into one of three intelligent, parameter-free, sequential data collection strategies (SwitchBAX, InfoBAX, and MeanBAX), bypassing the time-consuming and difficult process of task-specific acquisition function design. Our framework is tailored for typical discrete search spaces involving multiple measured physical properties and short time-horizon decision making. We demonstrate this approach on datasets for TiO 2 nanoparticle synthesis and magnetic materials characterization, and show that our methods are significantly more efficient than state-of-the-art approaches. Overall, our framework provides a practical solution for navigating the complexities of materials design, and helps lay groundwork for the accelerated development of advanced materials.

42 ENGINEERING↗

DOE OSTI2026

TETA Autoresearch [SWR-26-089]

TETA Autoresearch is a template repository based on github.com/karpathy/autoresearch for AI-assisted research science in the TETA group in the Center for Integrated Mobility Sciences (CIMS) center at the National Laboratory of the Rockies. This software is a template for running autonomous research experiments that iteratively improve an ML model for a single optimization objective. Two execution modes share one harness: LLM mode - an agent (e.g. Claude Code) edits a scaffold train.py one change at a time, tagging each experiment, logging reasoning, and pushing results. Defined by program.md. Optimizer mode - an Optuna-backed driver (TPE / CMA-ES / Random) iterates over a domain-defined search space. Defined by optimizers/. RouteE (vehicle energy prediction) is the reference domain under domains/routee/. Adding a new domain is mechanical - see EXTENDING.md.

Reinicke, Nicholas [National Laboratory of the Roc↗

NASA NTRS1989

Exploiting map plans as resources for action

When plans are used as programs for controlling the action of autonomous or teleoperated robots, their abstract representation can easily obscure a great deal of the critical knowledge that originally led to the planned course of action. An autonomous vehicle experiment is highlighted which illustrates how the information barriers created by abstraction can result in undesirable action. It is then shown how the same task can be performed correctly using plans as a resource for action. As a result of this simple change in outlook, problems requiring opportunistic reaction to unexpected changes in the environment can be solved.

Payton, David↗

NASA NTRS1992

Ambler - Performance of a six-legged planetary rover

In this paper, several performance metrics are quantified for the Ambler, a six-legged robot configured for autonomous traversal of Mars-like terrain. Power consumption measures are presented for walking on sandy terrain and for vertical lifts at different velocities. The performance of a novel dead reckoning approach is documented, and its accuracy is analyzed. The results of autonomous walking experiments are described in terms of terrain traversed, walking speed, and endurance.

Krotkov, E. P.↗

NASA NTRS1992

Performance of a six-legged planetary rover - Power, positioning, and autonomous walking

The authors quantify several performance metrics for the Ambler, a six-legged robot configured for autonomous traversal of Mars-like terrain. They present power consumption measures for walking on sandy terrain and for vertical lifts at different velocities. They document the accuracy of a novel dead reckoning approach, and analyze the accuracy. They describe the results of autonomous walking experiments in terms of terrain traversed, walking speed, number of instructions executed and endurance.

Krotkov, Eric↗