Search NASA⌕ Search

SEARCH · Search NASA

Results for “BOUNDARY LAYER NOISE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Space-Time Correlations and Spectra of Wall Pressure in a Turbulent Boundary Layer

Measurements of the statistical properties of the fluctuating wall pressure produced by a subsonic turbulent boundary layer are described. The measurements provide additional information about the structure of the turbulent boundary layer; they are applicable to the problems of boundary-layer induced noise inside an airplane fuselage and to the generation of waves-on water. The spectrum of the wall pressure is presented in dimensionless form. The ratio of the root-mean-square wall pressure to the free-stream dynamic pressure is found to be a constant square root of bar P(sup 2)/q(sub infinity) = 0.006 independent of Mach number and Reynolds number. In addition, space- time correlation measurements in the stream direction show that pressure fluctuations whose scale is greater than or equal to 0.3 times the boundary-layer thickness are convected with the convection speed U(sub c) = 0.82U(sub infinity) where U(infinity) is the free-stream velocity and have lost their identity in a distance approximately equal to 10 boundary-layer thicknesses.

Willmarth, W. W.↗
NASA NTRS1987

Flight survey of the 757 wing noise field and its effects on laminar boundary layer transition. Volume 2: Data compilation

A flight test program was performed using the Boeing 757 flight research airplane to investigate the effect of noise from wing mounted engines on laminar boundary layer transition. An NLF glove was installed on the right wing panel just outboard of the engine. The extent of laminar flow on the glove was measured as a function of engine power setting for a range of flight conditions. A combination of surface and probe microphones was distributed over the upper and lower wing surfaces to measure sound spectra. The flight test program was completed in June 1985 and the results of preliminary analysis indicate that a maximum of about 29 percent of chord laminar flow was obtained on the upper surface and about 28 percent on the lower surface (at a high sideslip condition). The engine speed was varied from about 2600 (idle) to about 4500 (maximum continuous power) r/min. This produced changes in sound pressure level up to 20 dB on the lower surface. On the upper surface, the noise levels were independent of engine power but sensitive to airplane Mach number. No effect of engine power setting on upper surface transition location was observed, and only a small forward movement of the transition location on the lower surface was observed at the high power settings. Volume 1 of this report contains the program description and data analysis. Volume 2 is a compilation of all of the flight test data.

Source record↗
NASA NTRS1984

Effects of boundary layer refraction and fuselage scattering on fuselage surface noise from advanced turboprop propellers

An acoustic disturbance's propagation through a boundary layer is discussed with a view to the analysis of the acoustic field generated by a propfan rotor incident to the fuselage of an aircraft. Applying the parallel flow assumption, the resulting partial differential equations are reduced to an ordinary acoustic pressure differential equation by means of the Fourier transform. The methods used for the solution of this equation include those of Frobenius and of analytic continuation; both yield exact solutions in series form. Two models of the aircraft fuselage-boundary layer system are considered, in the first of which the fuselage is replaced by a flat plate and the acoustic field is assumed to be two-dimensional, while in the second the fuselage is a cylinder in a fully three-dimensional acoustic field. It is shown that the boundary layer correction improves theory-data comparisons over simple application of a pressure-doubling rule at the fuselage.

Mcaninch, G. L.↗
NASA NTRS1986

Noise-driven sidebranching in the boundary-layer model of dendritic solidification

In the context of local models of solidification, it is suggested that the sidebranching which appears to be a characteristic feature of dendritic processes may be generated by selective amplification of noise near the tip and that, under some circumstances, thermal fluctuations may be strong enough to explain the observed effects. This proposal is discussed based on the two-dimensional boundary-layer model with kinetic crystalline anisotropy. Experimental methods to distinguish this stochastic process from a deterministic, dynamical sidebranching mechanism are suggested, including the possibility of space-based experiments.

Pieters, R.↗
NASA NTRS1988

Simulation of electrostatic turbulence in the plasma sheet boundary layer with electron currents and bean-shaped ion beams

Plasma data from ISEE-1 show the presence of electron currents as well as energetic ion beams in the plasma sheet boundary layer. Broadband electrostatic noise and low-frequency electromagnetic bursts are detected in the plasma sheet boundary layer, especially in the presence of strong ion flows, currents, and steep spacial gradients in the fluxes of few-keV electrons and ions. Particle simulations have been performed to investigate electrostatic turbulence driven by a cold electron beam and/or ion beams with a bean-shaped velocity distribution. The simulation results show that the counterstreaming ion beams as well as the counterstreaming of the cold electron beam and the ion beam excite ion acoustic waves with a given Doppler-shifted real frequency. However, the effect of the bean-shaped ion velocity distributions reduces the growth rates of ion acoustic instability. The simulation results also show that the slowing down of the ion bean is larger at the larger perpendicular velocity. The wave spectra of the electric fields at some points of the simulations show turbulence generated by growing waves.

Nishikawa, K.-I.↗
NASA NTRS1967

A theoretical and flight test study of pressure fluctuations under a turbulent boundary layer. Part 2: Flight test study

The study of pressure fluctuations under a turbulent boundary layer was undertaken with the objective of extending previous work to lower frequencies. Wind tunnel and flight test measurements are invalid at low frequencies because of extraneous acoustic noises and free stream turbulence. A glider was instrumented and used as a test bed to carry microphones into a smooth flow free of acoustic noise. Hodgson had previously measured the spectrum of boundary layer noise on a glider wing. These tests showed a drop off at low frequencies that could not be reproduced in any other facility. The measurements were made on the forward fuselage of a glider where the boundary layer could develop naturally and have some length in a zero pressure gradient before the measurements were made. Two different sets of measurements were made.

Panton, R. L.↗
NASA NTRS1973

Investigation of noise suppression by sonic inlets for turbofan engines. Volume 1: Program summary

Results of a program for sonic inlet technology development are presented. This program includes configuration and mechanical design selection of concepts, aerodynamic design description of the models, and results of test evaluation. Several sonic inlet concepts were tested and compared for aerodynamic and acoustic performance. Results of these comparative evaluations are presented. Near-field measurements were taken inside several of the inlet models. Results of these tests are discussed with respect to the effect of Mach number gradients on noise attenuation and rotor shock wave attenuation, and boundary layer effects on noise propagation. The test facilities and experimental techniques employed are described briefly.

Klujber, F.↗
NASA NTRS1973

Results of an experimental program for the development of sonic inlets for turbofan engines.

Results of a current program for sonic inlet technology development are presented. This program includes configuration and mechanical design selection of concepts, aerodynamic design description of the models, and results of test evaluation. In the test program several sonic inlet concepts were tested and compared for aerodynamic and acoustic performance. Results of these comparative evaluations are presented. Near-field measurements were taken inside the sonic inlet on several inlet models. Results of these tests are discussed with respect to the effect of Mach number gradients on noise attenuation and rotor shock wave attenuation, and boundary layer effects on noise propagation. The test facilities and experimental techniques employed are described briefly.

Klujber, F.↗
NASA NTRS1972

A procedure for predicting internal and external noise fields of blowdown wind tunnels

The noise generated during the operation of large blowdown wind tunnels is considered. Noise calculation procedures are given to predict the test-section overall and spectrum level noise caused by both the tunnel burner and turbulent boundary layer. External tunnel noise levels due to the tunnel burner and circular jet exhaust flow are also calculated along with their respective cut-off frequency and spectrum peaks. The predicted values are compared with measured data, and the ability of the prediction procedure to estimate blowdown-wind-tunnel noise levels is shown.

Hosier, R. N.↗
NASA NTRS2006

CDUCT-LaRC Status - Shear Layer Refraction and Noise Radiation

A proposed boundary condition accounting for shear layer effects within the Ffowcs Williams-Hawkings radiation module of the CDUCT-LaRC code is investigated. The development and numerical justification of the boundary condition formulation are reviewed. An initial assessment of the effectiveness of the shear layer correction is conducted through comparison with experimental data. Preliminary results indicate that the correction provides physically meaningful modifications of the baseline predicted directivity patterns. Trends of peak directivity steepening and shifting that appeared in predicted patterns were found to follow similar structures in measured data, particularly at higher radiation angles.

Nark, Douglas M.↗
NASA NTRS1974

Development of a high Reynolds number quiet tunnel for transition research

High noise levels in conventional supersonic and hypersonic wind tunnels prevent further advances in transition research. Recent data confirm previous results that transition is dominated by tunnel noise when the rms pressure intensities exceed about 1%. High facility noise levels also dominate fluctuating pressure loads under fully turbulent boundary layers. Recent data on the power spectra of surface pressures indicate that the basic structure of turbulent boundary layers may be modified by high facility noise levels. Experimental data for current techniques to control and reduce noise levels in supersonic and hypersonic wind tunnels by laminarization of nozzle wall boundary layers and by noise radiation shields are presented. These results and possible effects of Taylor-Gortler vortices observed in a nozzle wall boundary layer are used to predict the limits of quiet performance for a proposed 20-in. quiet tunnel.

Beckwith, I. E.↗
NASA NTRS1976

Some aspects on unsteady flow past airfoils and cascades

The unsteady boundary layer due to a gust propagating past an isolated airfoil and on airfoils in cascade was measured with a hot wire anemometer in a low speed gust tunnel. Coherent signals were obtained by a phase lock averaging technique that was implemented in an on-line analysis using a PDP 12 computer. Changes in a boundary layer shape factor, noise level, and pressure gradient were correlated over a complete gust cycle. It is concluded that the character of the boundary layer changes from laminar to turbulent and back to laminar during the course of a gust cycle at certain chordwise positions. These measurements help explain certain anomalies that were observed during a previous study of the pressure fluctuations due to gust loadings on airfoils and cascades.

Satyanarayana, B.↗
NASA NTRS1987

Flight survey of the 757 wing noise field and its effects on laminar boundary layer transition. Volume 1: Program description and data analysis

It was previously observed that an incident acoustic field on a wing with laminar flow can cause transition to turbulent flow if the fluctuating acoustic velocities are of sufficient amplitude and in the critical frequency range for an unstable laminar boundary layer. A section of a wing was modified with a natural laminar flow (NLF) glove to allow direct measurement of the effect of varying engine noise on the extent of laminar flow. The flight test program was completed in June, 1985. At each flight condition, the engine power was varied from about 2600 r/min (idle) to about 4500 r/min (maximum continuous power). The spectral data provides considerable insight into the influences of the various sound sources that contribute to the overall noise levels. Additional analysis will be required to assess the impact of these sources on boundary layer transition. These results demonstrate that substantial laminar flow on the wing of a transport configuration with wing-mounted engines can be obtained.

Source record↗
NASA NTRS1984

Correlations of supersonic boundary-layer transition on cones including effects of large axial variations in wind-tunnel noise

Transition data on sharp tip cones in two pilot low disturbance wind tunnels at Mach numbers of 3.5 and 5 were correlated in terms of noise parameters with data from several conventional wind tunnels and with data from supersonic flight tests on a transition cone. The noise parameters were developed to account for the large axial variations of the free stream noise and the very high frequency noise spectra that occurred in the low disturbance tunnels for some test conditions. The noise could be varied in these tunnels from high levels, approaching those in conventional tunnels, to extremely low levels. The correlations indicated that transition in the low disturbance tunnels was dominated by the local stream noise that was incident on the cone boundary layer unstream of the neutral stability point. The correlation results also suggested that high frequency components of the low disturbance tunnel noise spectra had significant effects on transition when the noise was incident on the boundary layer both upstream and downstream of the neutral stability point.

Chen, F. J.↗
NASA NTRS1990

High-speed quiet tunnels

The adverse effect of wind-tunnel noise on boundary-layer transition is considered, and the development of Pilot Quiet Tunnels exhibiting low noise levels in upstream regions of the test rhombus to high values of the stream unit Reynolds number is covered. Advances in quiet nozzle and tunnel designs are discussed, including a new Mach-8 nozzle and modifications to an existing conical nozzle in one of the helium tunnels at NASA Langley. Attention is focused on the final engineering design of a large-scale high-speed low-disturbance tunnel expected to accommodate nozzles of various lengths with Mach numbers ranging from 2 to 6.

Beckwith, Ivan E.↗
NASA NTRSDate not supplied

Computational Aerodynamic Analysis in Support of the CRM Tail Cone Thruster Configuration Wind Tunnel Test

NASA’s Advanced Air Transport Technology (AATT) project is breaching the boundaries of aircraft design in pursuit of eco-friendly solutions that are compatible with urban noise comfort levels. Boundary layer ingesting (BLI) propulsion systems promise to reduce fuel burn with additional potential benefits in noise reduction. Type-II BLI systems of the STARC-ABL type are the subject of a test campaign planned for fiscal year 2022 in the National Transonic Facility (NTF), for which a CRM-based model with a retrofitted tail cone thruster (TCT) has been designed. The present work is a precursor to the NTF test, where the 240 cases planned for the experiment were simulated using the Launch, Ascent and Vehicle Aerodynamics (LAVA)computational framework. Solution sensitivity to angle of attack, engine operating conditions, and the presence of the supporting structure (sting) in the wind tunnel test are analyzed in the extensive dataset. The main flow features contributing to the inlet distortion are identified as the vertical tail wake, wing downwash and fuselage upsweep vortices, with the latter two experiencing the greatest sensitivity to angle of attack. Finally, results from an inlet-guide-vane(IGV) design/integration study are presented. The LAVA team and the turbomachinery design team at NASA’s Ames and Glenn Research Centers are collaborating in an effort to reduce flow distortion upstream of the fan by means of integrating an IGV system into the CRM-TCT model. A significant improvement in flow distortion metrics has been achieved since the initial design iteration. Results employing an actuator zone model with realistic radially-varying thrust profiles to simulate first-order fan effects within LAVA are presented.

AATT↗
NASA NTRS1989

Acceleration of thermal plasma in the magnetosphere

Analytic theory and numerical simulations are used here to investigate the physics of two types of mixed plasmas. The transverse acceleration of ions on auroral field lines is considered in order to determine the effects of multiion species. In the auroral zone the components of a multiion plasma, including hydrogen and oxygen, interact with each other as well as with a two-component electron plasma composed of both a magnetospheric beam and background ionospheric components. This interaction occurs as a mixed ion-ion hybrid mode. How an electron plasma, with both hot and cold components as well as ion beams, affects the plasma sheet boundary layer is examined. It is found that in the presence of this mixed electron plasma, warm ion beams can drive the electron acoustic instability; this phenomenon may be responsible for broadband electrostatic noise in the boundary layer.

Ashour-Abdalla, Maha↗
NASA NTRS1987

Research in Natural Laminar Flow and Laminar-Flow Control, part 3

Part 3 of the Symposium proceedings contains papers addressing advanced airfoil development, flight research experiments, and supersonic transition/laminar flow control research. Specific topics include the design and testing of natural laminar flow (NLF) airfoils, NLF wing gloves, and NLF nacelles; laminar boundary-layer stability over fuselage forebodies; the design of low noise supersonic/hypersonic wind tunnels; and boundary layer instability mechanisms on swept leading edges at supersonic speeds.

Hefner, Jerry N.↗