Search NASA⌕ Search

SEARCH · Search NASA

Results for “BOUNDARY LAYER REMOVAL - SUCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Flight-determined characteristics of an air intake system on an F-111A airplane

Flow phenomena of the F-111A air intake system were investigated over a large range of Mach number, altitude, and angle of attack. Boundary-layer variations are shown for the fuselage splitter plate and inlet entrance stations. Inlet performance is shown in terms of pressure recovery, airflow, mass-flow ratio, turbulence factor, distortion factor, and power spectral density. The fuselage boundary layer was found to be not completely removed from the upper portion of the splitter plate at all Mach numbers investigated. Inlet boundary-layer ingestion started at approximately Mach 1.6 near the translating spike and cone. Pressure-recovery distribution at the compressor face showed increasing distortion with increasing angle of attack and increasing Mach number. The time-averaged distortion-factor value approached 1300, which is near the distortion tolerance of the engine at Mach numbers above 2.1.

Hughes, D. L.↗
NASA NTRS2004

Single-Stage, 3.4:1-Pressure-Ratio Aspirated Fan Developed and Demonstrated

Researchers are constantly pursuing technologies that will increase the performance of gas turbine engines. The aspirated compressor concept discussed here would allow the compression system to perform its task with about one-half of the compressor blades. To accomplish this, the researchers applied boundary layer control to the blades, casing, and hub. This method of boundary layer control consisted of removing small amounts of air from the main flow path at critical areas of the compressor. This bleed air could be used by other systems such as engine cooling or could be re-injected into lower pressure areas that require air for enhanced performance. This effort was initiated by the Massachusetts Institute of Technology (MIT) in response to a solicitation from the Defense Advanced Research Projects Agency (DARPA) who sought to advance research in flow control technology. The NASA Glenn Research Center partnered with MIT (principal investigator), Honeywell Aircraft Engines (cycle analysis, structural analysis, and mechanical design), and Pratt & Whitney (cycle analysis and aero-analysis) to conceptualize, design, analyze, build, and test the aspirated fan stage. The aero-design and aero-analysis of this fan stage were jointly executed by MIT and Glenn to minimize the amount of bleed flow needed and to maintain the highest efficiency possible (ref. 1). Mechanical design issues were complicated by the need to have a shrouded rotor with hollow blades, with rotor stress levels beyond the capabilities of titanium. The high stress issues were addressed by designing a shroud that was filament wound with a carbon fiber/epoxy matrix, resulting in an assembly that was strong enough to handle the high stresses. Both the rotor (preceding photographs) and stator (following photograph) were fabricated in two halves and then bolted together at the hub and tip, permitting the bleed passages to be machined into each half before assembly.

Braunscheidel, Edward P.↗
DOE OSTI2020

Coupling of Laminar-Turbulent Transition with RANS Computational Fluid Dynamics

This project combines several new concepts to create a boundary layer transition prediction capability that is suitable for analyzing modern hypersonic flight vehicles. The first new concept is the use of ''optimization'' methods to detect the hydrodynamic instabilities that cause boundary layer transition; the use of this method removes the need for many limiting assumptions of other methods and enables quantification of the interactions between boundary layer instabilities and the flow field imperfections that generate them. The second new concept is the execution of transition analysis within a conventional hypersonics CFD code, using the same mesh and numerical schemes for the transition analysis and the laminar flow simulation. This feature enables rapid execution of transition analysis with less user oversight required and no interpolation steps needed.

42 ENGINEERING↗
DOE OSTI2020

Ultra-clean and smoky marine boundary layers frequently occur in the same season over the southeast Atlantic

We study 41 d with daily median surface accumulation mode aerosol particle concentrations below 50 cm -3 (ultra-clean conditions) observed at Ascension Island (ASI; 7.9° S, 14.4° W) between June 2016 and October 2017 as part of the Layered Atlantic Smoke Interactions with Clouds (LASIC) campaign. Interestingly, these days occur during a period of great relevance for aerosol–cloud–radiation interactions, the southeast Atlantic (SEATL)biomass-burning season (approximately June–October). That means that these critical months can feature both the highest surface aerosol numbers, from smoke intrusion into the marine boundary layer, as well as the lowest. While carbon monoxide and refractory black carbon concentrations on ultra-clean days do not approach those on days with heavy smoke, they also frequently exceed background concentrations calculated in the non-burning season from December 2016 to April 2017. This is evidence that even what become ultra-clean boundary layers can make contact with and entrain from an overlying SEATL smoke layer before undergoing a process of rapid aerosol removal. Because many ultra-clean and polluted boundary layers observed at Ascension Island during the biomass burning season follow similar isobaric back trajectories, the variability in this entrainment is likely more closely tied to the variability in the overlying smoke rather than large-scale horizontal circulation through the boundary layer. Since exceptionally low accumulation mode aerosol numbers at ASI do not necessarily indicate the relative lack of other trace pollutants, this suggests the importance of regional variations in what constitutes an “ultra-clean” marine boundary layer. Finally, surface drizzle rates, frequencies and accumulation – as well as retrievals of liquid water path– all consistently tend toward higher values on ultra-clean days. This implicates enhanced coalescence scavenging in low clouds as the key driver of ultra-clean events in the southeast Atlantic marine boundary layer. These enhancements occur against and are likely mediated by the backdrop of a seasonal increase in daily mean cloud fraction and daily median liquid water path over ASI, peaking in September and October in both LASIC years. Therefore the seasonality in ultra-clean day occurrence seems directly linked to the seasonality in SEATL cloud properties. These results highlight the importance of two-way aerosol–cloud interactions in the region.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRSDate not supplied

Advancing xEMU Lunar Dust Mitigation Devices

Fine, electrically charged, glass like dust particles caused significant damage to the Apollo EMU9 during lunar EVAs, identified as one of the greatest challenges to future exploration. Passive Lunar Dust Mitigation Devices (LDMD) were developed, within a SBIR Phase II, to prohibit this dust from interrupting venting space suit component operation. A Computational Fluid-Dynamics and Discrete Element Method (CFD-DEM) Simulation Tool was developed at the University of Colorado, Boulder to predict venting gas flow ability to self-clean adhered dust particles from LDMD surfaces. Lunar dust properties (i.e., adhesion and cohesion strengths) required to complete Simulation Tool analysis are relatively unknown due to considerable differences between the Earth and the Moon (i.e., gravity, humidity) and due to an absence of dust particles in their native state. Analytically determining gas flow velocity, density and direction within the fluid Boundary Layer, microns from LDMD surfaces presented a second challenge. Dusty Plasma Chamber testing is being performed at Auburn University, Auburn to observe electrostatically charged dust behavior as it adheres to LDMD prototypes and specific geometry and is then blown away by metered gas flow. Test articles were developed to offer insight into the impact of different flow geometries, surface roughness and dust removal within the gas Boundary-Layer. Observed dust behavior is currently being developed to support the CFD-DEM analysis. Many Simulation Tool analytical cases have been processed to support the intention of completing sensitivity studies to assess how different dust adherence values and Boundary Layer fluid properties impact LDMD self-cleaning effectivity.

Thomas J Stapleton↗
DOE OSTI2023

Low ozone dry deposition rates to sea ice during the MOSAiC field campaign: Implications for the Arctic boundary layer ozone budget

Dry deposition to the surface is one of the main removal pathways of tropospheric ozone (O 3 ). We quantified for the first time the impact of O 3 deposition to the Arctic sea ice on the planetary boundary layer (PBL) O 3 concentration and budget using year-round flux and concentration observations from the Multidisciplinary drifting Observatory for the Study of Arctic Climate (MOSAiC) campaign and simulations with a single-column atmospheric chemistry and meteorological model (SCM). Based on eddy-covariance O 3 surface flux observations, we find a median surface resistance on the order of 20,000 s m –1 , resulting in a dry deposition velocity of approximately 0.005 cm s –1 . This surface resistance is up to an order of magnitude larger than traditionally used values in many atmospheric chemistry and transport models. The SCM is able to accurately represent the yearly cycle, with maxima above 40 ppb in the winter and minima around 15 ppb at the end of summer. However, the observed springtime ozone depletion events are not captured by the SCM. In winter, the modelled PBL O 3 budget is governed by dry deposition at the surface mostly compensated by downward turbulent transport of O 3 towards the surface. Advection, which is accounted for implicitly by nudging to reanalysis data, poses a substantial, mostly negative, contribution to the simulated PBL O 3 budget in summer. During episodes with low wind speed (<5 m s –1 ) and shallow PBL (<50 m), the 7-day mean dry deposition removal rate can reach up to 1.0 ppb h –1 . Our study highlights the importance of an accurate description of dry deposition to Arctic sea ice in models to quantify the current and future O 3 sink in the Arctic, impacting the tropospheric O 3 budget, which has been modified in the last century largely due to anthropogenic activities.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1981

Modification in drag of turbulent boundary layers resulting from manipulation of large-scale structures

The effects of placing a parallel-plate turbulence manipulator in a boundary layer are documented through flow visualization and hot wire measurements. The boundary layer manipulator was designed to manage the large scale structures of turbulence leading to a reduction in surface drag. The differences in the turbulent structure of the boundary layer are summarized to demonstrate differences in various flow properties. The manipulator inhibited the intermittent large scale structure of the turbulent boundary layer for at least 70 boundary layer thicknesses downstream. With the removal of the large scale, the streamwise turbulence intensity levels near the wall were reduced. The downstream distribution of the skin friction was also altered by the introduction of the manipulator.

Corke, T. C.↗
NASA NTRS1989

Experience with some repeat tests on the 9 inch chord CAST-10-2/DOA 2 airfoil model in the Langley 0.3-m TCT adaptive wall test section

A co-operative testing program is in progress between the Langley Research Center (NASA) and the National Aeronautical Establishment (NAE, Canada) to validate two different techniques of airfoil testing at transonic speeds. The procedure employed is to test the same airfoil model in the NAE two-dimensional tunnel and the Langley 0.3-m Transonic Cryogenic Tunnel (0.3-m TCT). The airfoil model used in testing was CAST-10-2/DOA-2 super-critical airfoil. The Langley 0.3-m TCT has a relatively small cross section of 13 in x 13 in, giving a (h/c) ratio of 1.44 for the same 9 in chord model. The approach employed in the 0.3-m TCT aims towards eliminating the wall effects by using active walls. The top and bottom walls are flexible. By changing the wall shapes during a test in an iterative manner, the wall interference effects are reduced. The method employed to change the wall shapes is the adaptive wall technique. The current test program provided an opportunity to validate the adaptive wall technique in the 0.3-m TCT. The relatively long chord airfoil represents a severe test case to test the efficacy of the adaptive wall technique under cryogenic conditions. The program also involved removal of side wall boundary-layer thus increasing the complexity of the wall adaptation technique. This paper deals with some salient results obtained regarding repeatability of test data and possible residual interference effects.

Murthy, A. V.↗
NASA NTRS1995

Flow Coefficient Behavior for Boundary Layer Bleed Holes and Slots

An experimental investigation into the flow coefficient behavior for nine boundary layer bleed orifice configurations is reported. This test was conducted for the purposes of exploring boundary layer control through mass flow removal and does not address issues of stability bleed. Parametric data consist of bleed region flow coefficient as a function of Mach number, bleed plenum pressure, and bleed orifice geometry. Seven multiple hole configurations and two single slot configurations were tested over a supersonic Mach number range of 1.3 to 2.5 (nominal). Advantages gained by using multiple holes in a bleed region instead of a single spanwise slot are discussed and the issue of modeling an entire array of bleed orifices based on the performance of a single orifice is addressed. Preconditioning the flow approaching a 90 degree inclined (normal) hole configuration resulted in a significant improvement in the performance of the configuration. The same preconditioning caused only subtle changes in performance for a 20 degree inclined (slanted) configuration.

Willis, B. P.↗
NASA NTRS2011

Control of Stationary Cross-Flow Modes in a Mach 3.5 Boundary Layer Using Patterned Passive and Active Roughness

Spanwise-periodic roughness designed to excite selected wavelengths of stationary cross- ow modes was investigated in a 3-D boundary layer at Mach 3.5. The test model was a sharp-tipped 14deg right-circular cone. The model and integrated sensor traversing system were placed in the Mach 3.5 Supersonic Low Disturbance Tunnel (SLDT) equipped with a "quiet design" nozzle at the NASA Langley Research Center. The model was oriented at a 4:2deg angle of attack to produce a mean cross-fl ow velocity component in the boundary layer over the cone. Five removable cone tips have been investigated. One has a smooth surface that is used to document the baseline ("natural") conditions. Two had minute (20 - 40 micron) "dimples" that are equally spaced around the circumference, at a streamwise location that is just upstream of the linear stability neutral growth branch for cross- ow modes. The azimuthal mode numbers of the dimpled tips were selected to either enhance the most amplified wave numbers, or to suppress the growth of the most amplified wave numbers. Two of the cone tips had an array of plasma streamwise vortex generators that were designed to simulate the disturbances produced by the passive patterned roughness. The results indicate that the stationary cross-fl ow modes were highly receptive to the patterned roughness of both passive and active types. The patterned passive roughness that was designed to suppress the growth of the most amplified modes had an azimuthal wavelength that was 66% smaller that that of the most amplified stationary cross- ow mode. This had the effect to increase the transition Reynolds number from 25% to 50% depending on the measurement technique. The application of the research is on turbulent transition control on swept wings of supersonic aircraft. The plasma-based roughness has the advantage over the passive roughness of being able to be adaptable to different conditions that would occur during a flight mission.

Schuele, Chan Yong↗
NASA NTRS1951

Comparison of Theoretical and Experimental Heat-Transfer Characteristics of Bodies of Revolution at Supersonic Speeds

An investigation of the three important factors that determine convective heat-transfer characteristics at supersonic speeds, location boundary-layer transition, recovery factor, and heat-transfer parameter has been performed at Mach numbers from 1.49 to 1.18. The bodies of revolution that were tested had, in most cases, laminar boundary layers, and the test results have been compared with available theory. Boundary-layer transition was found to be affected by heat transfer. Adding heat to a laminar boundary layer caused transition to move forward on the test body, while removing heat caused transition to move rearward. These experimental results and the implications of boundary-layer-stability theory are in qualitative agreement.

Scherrer, Richard↗
NASA NTRS1985

Flow field survey near the rotational plane of an advanced design propeller on a JetStar airplane

An investigation was conducted to obtain upper fuselage surface static pressures and boundary layer velocity profiles below the centerline of an advanced design propeller. This investigation documents the upper fuselage velocity flow field in support of the in-flight acoustic tests conducted on a JetStar airplane. Initial results of the boundary layer survey show evidence of an unusual flow disturbance, which is attributed to the two windshield wiper assemblies on the aircraft. The assemblies were removed, eliminating the disturbances from the flow field. This report presents boundary layer velocity profiles at altitudes of 6096 and 9144 m (20,000 and 30,000 ft) and Mach numbers from 0.6 to 0.8, and it investigated the effects of windshield wiper assemblies on these profiles. Because of the unconventional velocity profiles that were obtained with the assemblies mounted, classical boundary layer parameters, such as momentum and displacement thicknesses, are not presented. The effects of flight test variables (Mach number and angles of attack and sideslip) and an advanced design propeller on boundary layer profiles - with the wiper assemblies mounted and removed - are presented.

Walsh, K. R.↗
NASA NTRS1993

Semi-span model testing in the National Transonic Facility

A semi-span testing technique has been proposed for the NASA Langley Research Center's National Transonic Facility (NTF). Semi-span testing has several advantages including (1) larger model size, giving increased Reynolds number capability; (2) improved model fidelity, allowing ease of flap and slat positioning which ultimately improves data quality; and (3) reduced construction costs compared with a full-span model. In addition, the increased model size inherently allows for increased model strength, reducing aeroelastic effects at the high dynamic pressure levels necessary to simulate flight Reynolds numbers. The Energy Efficient Transport (EET) full-span model has been modified to become the EET semi-span model. The full-span EET model was tested extensively at both NASA LRC and NASA Ames Research Center. The available full-span data will be useful in validating the semi-span test strategy in the NTF. In spite of the advantages discussed above, the use of a semi-span model does introduce additional challenges which must be addressed in the testing procedure. To minimize the influence of the sidewall boundary layer on the flow over the semi-span model, the model must be off-set from the sidewall. The objective is to remove the semi-span model from the sidewall boundary layer by use of a stand-off geometry. When this is done however, the symmetry along the centerline of the full-span model is lost when the semi-span model is mounted on the wind tunnel sidewall. In addition, the large semi-span model will impose a significant pressure loading on the sidewall boundary layer, which may cause separation. Even under flow conditions where the sidewall boundary layer remains attached, the sidewall boundary layer may adversely effect the flow over the semi-span model. Also, the increased model size and sidewall mounting requires a modified wall correction strategy. With these issues in mind, the semi-span model has been well instrumented with surface pressure taps to obtain data on the expected complex flow field in the near wall region. This status report summarizes the progress to date on developing the semi-span geometry definition suitable for generating structured grids for the computational research. In addition, the progress on evaluating three state-of-the-art Navier-Stokes codes is presented.

Chokani, Ndaona↗
NASA NTRS1986

Effects of initial condition on circular and elliptic jet noise

Noise produced by cold elliptic jets was studied experimentally using a 4 cm air jet in an anechoic chamber by varying the aspect ratio, nozzle exit boundary layer, and Mach number. Elliptic geometry is found to accentuate the sound produced by pairing of the shear layer vortices in the laminar boundary jet. Calculation of the pressure field produced by the pairing of elliptic vortex rings shows that the ratio of sound intensities produced by the pairing of inviscid elliptic vortex filament rings should be equal to their aspect ratio, the minor axis producing greater sound. Tripping the nozzle boundary layer changes the instability of the shear layer and removes the laminar vortices. If the sound produced by pairing and/or breakdown is considered to be the difference between laminar and turbulent jet noise, the pairing mechanism is seen to be very significant in laminar boundary layer jets.

Bridges, J. E.↗
DOE OSTI2021

Graupel Precipitating From Thin Arctic Clouds With Liquid Water Paths Less Than 50 g m -2

Rimed precipitation growth can efficiently remove moisture and aerosols from the boundary layer, yet thin low-level Arctic mixed-phase clouds are generally thought to precipitate pristine and aggregated ice crystals. Here we present automated surface photographic measurements showing that only 34% of precipitation particles exhibit negligible riming and that graupel particles ≥ in diameter commonly fall from clouds with liquid water paths less than 50 g m -2 . Analyses indicate that significant riming enhancement can occur provided sustained updrafts of 0.4 m s -1 , consistent with those measured in Arctic clouds. A Lagrangian numerical simulation that tracks falling particles suggests that similar updraft speeds can account for about one half of the observed riming enhancement. Riming enhancement appears particularly likely when weak temperature inversions are observed at cloud top, but a full explanation remains to be determined.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1952

Analytical and Experimental Investigation of Inlet-engine Matching for Turbojet-powered Aircraft at Mach Numbers up to 2.0

An analysis of inlet-turbojet-engine matching for a range of Mach numbers up to 2.0 indicates large performance penalties when fixed-geometry inlets are used. Use of variable-geometry inlets, however, nearly eliminates th The analysis was confirmed experimentally by investigating at Mach numbers of 0, 0.63, and 1.5 to 2.0 two single oblique-shock-type inlets of different compression-ramp angles, which simulated a variable-geometry configuration. The experimental investigation indicated that total-pressure recoveries comparable withose attainable with well designed nose inlets were obtained with the side inlets when all the boundary layer ahead of the inlets was removed. Serious drag penalties resulted at a Mach number of 2.0 from the use of blunt-cowl leading edges. However, sharp-lip inlets produced large losses in thrust for the take-off condition. These thrust penalties which are associated with the the low-speed operation of the sharp-lip inlet designs can probably be avoided without impairing the supersonic performance of the inlet by the use of auxiliary inlets or blow-in doors.

Esenwein, Fred T↗
NASA NTRS2012

Shock Generation and Control Using DBD Plasma Actuators

This report is the final report of a NASA Phase I SBIR contract, with some revisions to remove company proprietary data. The Shock Boundary Layer Interaction (SBLI) phenomena in a supersonic inlet involve mutual interaction of oblique shocks with boundary layers, forcing the boundary layer to separate from the inlet wall. To improve the inlet efficiency, it is desired to prevent or delay shock-induced boundary layer separation. In this effort, Innovative Technology Applications Company (ITAC), LLC and the University of Notre Dame (UND) jointly investigated the use of dielectric-barrier-discharge (DBD) plasma actuators for control of SBLI in a supersonic inlet. The research investigated the potential for DBD plasma actuators to suppress flow separation caused by a shock in a turbulent boundary layer. The research involved both numerical and experimental investigations of plasma flow control for a few different SBLI configurations: (a) a 12 wedge flow test case at Mach 1.5 (numerical and experimental), (b) an impinging shock test case at Mach 1.5 using an airfoil as a shock generator (numerical and experimental), and (c) a Mach 2.0 nozzle flow case in a simulated 15 X 15 cm wind tunnel with a shock generator (numerical). Numerical studies were performed for all three test cases to examine the feasibility of plasma flow control concepts. These results were used to guide the wind tunnel experiments conducted on the Mach 1.5 12 degree wedge flow (case a) and the Mach 1.5 impinging shock test case (case b) which were at similar flow conditions as the corresponding numerical studies to obtain experimental evidence of plasma control effects for SBLI control. The experiments also generated data that were used in validating the numerical studies for the baseline cases (without plasma actuators). The experiments were conducted in a Mach 1.5 test section in the University of Notre Dame Hessert Laboratory. The simulation results from cases a and b indicated that multiple spanwise actuators in series and at a voltage of 75 kVp-p could fully suppress the flow separation downstream of the shock. The simulation results from case c showed that the streamwise plasma actuators are highly effective in creating pairs of counter-rotating vortices, much like the mechanical vortex generators, and could also potentially have beneficial effects for SBLI control. However, to achieve these effects, the positioning and the quantity of the DBD actuators used must be optimized. The wind tunnel experiments mapped the baseline flow with good agreement to the numerical simulations. The experimental results were conducted with spanwise actuators for cases a and b, but were limited by the inability to generate a sufficiently high voltage due to arcing in the wind-tunnel test-section. The static pressure in the tunnel was lower than the static pressure in an inlet at flight conditions, promoting arching and degrading the actuator performance.

Patel, Mehul P.↗
NASA NTRSDate not supplied

Thermomechanical Relaxation of Vibrationally Excited NO in a Hypersonic Turbulent Boundary Layer

The effects of thermal nonequilibrium are studied using a DC glow discharge plasma to selectively modify the vibrational temperature of an otherwise cold flow. These experiments were performed at 𝑴=5.7and 𝑹𝒆=6×10 6 /m in the Actively Controlled Expansion tunnel at Texas A&M University on a canonical 2.75° half-angle wedge test article. A∼47 W plasma was generated across spanwise electrodes, and removable trips produced either a laminar or turbulent boundary layer. NO planar laser-induced fluorescence (PLIF) quantified the extent of the NO 𝑿 2 𝚷 (𝒗=1) vibrational perturbation due to the plasma and its subsequent interplay with the boundary layer, the first such data of which the authors are aware. NOPLIF measurements were taken at three locations along the test article, and quasi-temperature measurements are reported at each. Despite not quantifiably perturbing the boundary layer, the plasma was shown to alter the NO vibrational temperature profile therein. Independent analysis of the thermodynamics and fluid mechanics of the system suggests each set of physics could explain the results observed near and far from the wall, respectively.

Casey J. Broslawski↗