SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Computer program simulates specific bulkhead fittings by subjecting the desired geometry configuration to a membrane force, an external force, an external moment, an external tank pressure, or any combination of the above. This program generates a general model of bulkhead fittings for the Saturn booster.
A one man inflatable life raft is described. The raft has an inflatable tube perimetrically bounding the occupant receiving space with a flexible floor member. A zippered opening in the floor allows entry and facilitates the use of a constant diameter tube. An airtight fabric bulkhead divides the peripheral tube longitudinally into inflatable tube sections, where if either tube section were punctured, the bulkhead would move into the punctured section to substitute for the punctured wall portion and maintain the inflatable volume of the tube. The floor member is attached to the central portion of the tube wall so that either side of the raft can be the up side.
The buckling of a truncated elastic conical shell subjected to an axial compression is a classical problem in shell structures. The paper reinvestigates the buckling of an axially compressed truncated conical shell with rigid bulkheads. Two improvements are achieved. First, the condition that the total horizontal displacement must vanish due to rigid bulkhead and axisymmetry is treated as a constraint. This constraint is incorporated into the system through the use of the Lagrange multiplier; then the variational method is used to derive a complete set of boundary conditions for conical shells. Second, the stability is evaluated in the deformed state using the asymptotic solutions of the pair of Donnell-type equations for axisymmetric configuration. The results indicate that the buckling strength of conical shells depends mainly on the condition of the smaller end. In addition to the vertex angle, the distance ratio plays, at least, an equally important role.
The NASA Langley Research Center participated in the Solar Array Experiment with two primary objectives: (1) to study the structural and control dynamics of a new class of large, lightweight, low-frequency space structures, and (2) to develop technology for remote video measurement of structural motions. The shuttle orbiter's closed circuit television (CCTV) system was used to provide recorded video images of the solar array from four locations in the payload bay, two on the forward bulkhead and two on the aft bulkhead. White reflective targets were placed on the array to provide discrete points at which to track array motion. A dynamic test consisted of a quiescent period in which orbiter operations were inhibited and crew motion restricted, an excitation period, and a free decay period. The orbiter was placed in free drift while in a gravity gradient orientation and dynamics tests were timed to occur at orbital noon so that the Sun would illuminate one side of the array and Earth albedo the other. The CCTV system was turned on during the quiescent period, approximately 3 minutes prior to excitation. Video from all four CCTV cameras was recorded continuously through the excitation and free-decay periods for a total test record of 8 to 10 minutes.
The analysis of empirical modal models of structural components using techniques based on the modal assurance criterion (MAC) defined by Ewins (1984) is discussed and demonstrated for the case of the Space Shuttle Orbiter aft bulkhead. Modal models of the bulkhead are constructed before and after environmental acoustic tests equivalent to 30 or 100 missions and compared (by computing their MACs) to detect significant structural changes; subdivision of the modal vector followed by computation of the MAC for each part is used to localize the changes. Numerical data demonstrating the usefulness of the MAC approach are presented in tables and diagrams.
The thermal protection systems (TPS) for the Shuttle/Centaur were designed to provide fail-safe thermal protection during prelaunch, launch ascent, and on-orbit operations as well as during potential abort, where the Shuttle and Centaur would return to earth. The TPS selected used a helium-purged polyimide foam beneath three radiation shields for the liquid-hydrogen (LH2) tank and radiation shields only for the liquid-oxygen (LO2) tank. A double-walled vacuum bulkhead separated the two tanks. The LH2 tank had one 1.9 cm-thick layer of foam on the forward bulkhead and two layers on the larger-area sidewall. Full scale tests of the flight vehicle in a simulated Shuttle cargo bay gave total prelaunch heating rates of 29.5 and 12.9 kW for the LH2 and LO2 tanks, respectively. Calorimeter tests on a representative sample of the LH2 tank sidewall TPS indicated that the measured unit heating one would rapidly decrease from the prelaunch rate of about 300 W/sq m to a desired rate less than 4 W/sq m once on-orbit.
A method is developed to compute frequency response and acoustic radiation of a complex shell. The axisymmetric geometry of the shell includes cylindrical, conical, and spherical segments stiffened by discrete rings and bulkheads. The shell is coupled to internal masses and elastic frames. Shell segments are treated by transfer matrices. Rings, bulkheads, frames, and concentrated masses are treated by impedances at junctions of segments. The shell is coupled to an external acoustic fluid treated by Green's function and curved surface elements. A major issue facing the method's treatment of the fluid would be lack of existence or uniqueness encountered in the uncoupled, external acoustic problem at characteristic wavenumbers. By using a simple spherical shell, without internal structures, this potential hindrance is shown not to arise. A fuller application of the method awaits subsequent results.
Foam multilayer insulation (FMLI), a reusable thermal control system (TCS), was evaluated in a simulated orbit hold environment on a test tank of 3.0 ft diameter, 5.6 ft length, and 34.5 cu ft volume. The TCS consisted of a 0.44-inch thick foam and a 16-layer (17 sheet) MLI blanket attached to the tank barrel and lower bulkhead, with the upper bulkhead covered with a 2.7-inch foam and a 31-layer (32 sheets) MLI blanket. Average insulation heating rates during orbit hold simulations ranged from 10.5 to 28.1 Btu/hr for warm boundary temperatures from 300 to 460 R, respectively. These rates corresponded to liquid losses of 0.9 and 2.3 percent of the tank's volume per day. This liquid loss rate would be significantly reduced for full size vehicle tanks due to the decreased surface area-to-volume ratio as compared to the test tank.
A monocoque box beam consisting of a 24S-T aluminum-alloy sheet reinforced by four bulkheads and by longitudinal stringers and corner posts was subjected to bending loads as follows: pure bending about the lift axis, cantilever bending about the lift axis, and pure bending about both lift and drag axis. Longitudinal strains were measured for loads up to a load at which permanent set became measurable. The loads were sufficient to produce buckling of the sheet between stringers on the compression side of the box. The only noticeable effect of this buckling was a small increase in extreme-fiber strain on the compression side. The measured strains and measured deflections differed less than 10 percent from those computed from the simple beam theory after taking account of the effective width of the buckled sheet. The effect of the bulkheads on the distribution of stringer strain was negligible.
The first part of this report shows the differences between commercial and war airships and then goes on to show how some of the problems were solved. Their thorough investigations of these problems finally enabled the Schutte-Lanz Company to construct bulkhead diagrams for determining the buoyancy of airships, by means of which the size of each cell was established. These diagrams were derived from bulkhead diagrams employed in ship designing and are used in a similar manner.
The present report describes tests in which the stress distribution may be determined in a stiffened circular cylindrical shell loaded longitudinally at four symmetrically situated points. As being of particular importance are the cases investigated of groups of bending and arching or convexing forces, respectively. From the stress measurements on the longitudinal stiffeners, the shear stresses and the bulkhead ring stresses in the skin could be evaluated. These measurements showed that the "simple shear field" used in theoretical computations in which all normal stresses in the skin are neglected, must be extended by the addition of the transverse or circumferential stresses if the bulkhead rings are not riveted to the skin.
At the ends of a monocoque fuselage concentrated axial forces in the skin must generally be taken up. Such axial forces must also be taken up in the case of other members where axial forces from the neighboring stressed skin construction must be considered. In order to take up these axial forces two bulkheads or reinforcing frames may be arranged at the positions where the forces are applied. If these bulkheads are in the form of rings, bending moments are set up in them. In the present paper computations are performed for obtaining the value of these bending moments.
Several techniques that influence the low frequency scattering from penetrable edge terminations are evaluated using a hybrid finite element and boundary element method code. The edge terminations consist of a dielectric skin forming an exterior shape with an internal conducting bulkhead. Some of the techniques considered are bulkhead shaping, internal material loading, placement of resistive cards, and the placement of lossy dielectric material rods. The intent of the various treatments is to find a combination or combinations that influence(s) the backscattered field to acceptable levels over a range of frequencies for both transverse magnetic and transverse electric polarizations.
An experimental study was made on five 2024-T3 aluminum-alloy multiweb wing structures (MW-2-(4), MW-4-(3), mw-16, MW-17, and MW-18), at a Mach number of 2 and an angle of attack of 2 deg under simulated supersonic flight conditions. These models, of 20-inch chord and semi-span and 5-percent-thick circular-arc airfoil section, were identical except for the type and amount of chordwise stiffening. One model with no chordwise ribs between root and tip bulkhead fluttered and failed dynamically partway through its test. Another model with no chordwise ribs (and a thinner tip bulkhead) experienced a static bending type of failure while undergoing flutter. The three remaining models with one, two, or three chordwise ribs survived their tests. The test results indicate that the chordwise shear rigidity imparted to the models by the addition of even one chordwise rib precludes flutter and subsequent failure under the imposed test conditions. This paper presents temperature and strain data obtained from the tests and discusses the behavior of the models.
The Cryogenic Tank Technology Program (CTTP) program has been a cooperative effort between NASA LARC, NASA MSFC, NASA Headquarters, and industry (Lockheed Martin Aeronautics, Lockheed Martin Manned Space Systems, Wyman Gordon, and Ladish). The scope of the CTTP is to develop state-of-the-art, flight-size, flight-quality, low cost hardware, and use this hardware to design, fabricate and test an all aluminum-lithium, all near net shape-component 14' diameter cryogenic tank with a unique low profile bulkhead design. The logical conclusion to the CTTP is to validate these various technologies to a Technology Readiness Level (TRL) of 6 through the proposed structural test program. The CTTP supports the advancement of key enabling technologies required for aluminum lithium cryogenic tanks. The technologies are focused towards innovative and low cost manufacturing processes such as near net shape technologies: one piece spun formed domes, extruded barrel panels, and one piece roll forged ring frames. Other innovative technologies include the friction stir weld process and weight-efficient low profile bulkhead designs. All of these technologies are of primary importance for NASA's mission plan for reusable and expendable launch vehicles. This program fills the niche for an all 2195 aluminum lithium alloy cryogenic tank which is not being covered by existing NASA technology work.
The Ares I rocket is the first launch vehicle scheduled for manufacture under the National Aeronautic and Space Administration's (NASA's) Constellation program. A series of full-scale Ares I development articles have been constructed on the Robotic Weld Tool at the NASA George C. Marshall Space Flight Center in Huntsville, Alabama. The Robotic Weld Tool is a 100 ton, 7-axis, robotic manufacturing system capable of machining and friction stir welding large-scale space hardware. This presentation will focus on the friction stir welding of 5.5m diameter cryogenic fuel tank components; specifically, the liquid hydrogen forward dome (LH2 MDA), the common bulkhead manufacturing development articles (CBMDA) and the thermal protection system demonstration dome (TPS Dome). The LH2 MDA was the first full-scale, flight-like Ares I hardware produced under the Constellation Program. It is a 5.5m diameter elliptical dome assembly consisting of eight gore panels, a y-ring stiffener and a manhole fitting. All components are made from aluminumlithium alloy 2195. Conventional and self-reacting friction stir welding was used on this article. An overview of the manufacturing processes will be discussed. The LH2 MDA is the first known fully friction stir welded dome ever produced. The completion of four Common Bulkhead Manufacturing Development Articles (CBMDA) and the TPS Dome will also be highlighted. Each CBMDA and the TPS Dome consists of a 5.5m diameter spun-formed dome friction stir welded to a y-ring stiffener. The domes and y-rings are made of aluminum 2014 and 2219 respectively. The TPS Dome has an additional aluminum alloy 2195 barrel section welded to the y-ring. Manufacturing solutions will be discussed including "fixtureless" welding with self reacting friction stir welding.
The Ares I rocket is the first launch vehicle scheduled for manufacture under the National Aeronautic and Space Administration s (NASA s) Constellation program. A series of full-scale Ares I development articles have been constructed on the Robotic Weld Tool at the NASA George C. Marshall Space Flight Center in Huntsville, Alabama. The Robotic Weld Tool is a 100 ton, 7-axis, robotic manufacturing system capable of machining and friction stir welding large-scale space hardware. This presentation will focus on the friction stir welding of 5.5m diameter cryogenic fuel tank components; specifically, the liquid hydrogen forward dome (LH2 MDA) and the common bulkhead manufacturing development articles (CBMDA). The LH2 MDA was the first full-scale, flight-like Ares I hardware produced under the Constellation Program. It is a 5.5m diameter elliptical dome assembly consisting of eight gore panels, a y-ring stiffener and a manhole fitting. All components are made from aluminum-lithium alloy 2195. Conventional and self-reacting friction stir welding was used on this article. Manufacturing solutions will be discussed including the implementation of photogrammetry, an advanced metrology technique, as well as fixtureless welding. The LH2 MDA is the first known fully friction stir welded dome ever produced. The completion of four Common Bulkhead Manufacturing Development Articles (CBMDA) will also be highlighted. Each CBMDA consists of a 5.5m diameter spun-formed dome friction stir welded to a y-ring stiffener. The domes and y-rings are made of aluminum 2014 and 2219 respectively. An overview of CBMDA manufacturing processes and the effect of tooling on weld defect formation will be discussed.
The Habitat Demonstration Unit (HDU) Project in conjunction with the NASA Extravehicular Activity (EVA) team has identified a need for a hybrid inflatable and hard shell suitlock that can be used for planetary surface and deep space human exploration missions. Through ongoing analog studies at NASA Desert Research and Technologies Studies (D-RATS) and in NASA's Prototyping Testbed Facility, it has been determined that a compactly stowed, deployable suitlock unit is needed to accommodate advanced EVA egress and ingress operations for various environments with only minor modification.The Dual-Chamber Inflatable Suitlock (DCIS) consists of three hard in-line bulkheads, separating two cylindrical membrane-walled compartments. A dual-compartment suitlock will allow for dust and contaminant control, suit maintenance, and efficient egress / ingress; and the inflatable aspect of the design will allow the unit to stow in a compact package for transport. This paper describes the DCIS functionality, subsystems, and operational scenarios.The novel concepts included in the DCIS are the triple bulkhead, dual-chamber that has one compartment that is continuously pressurized (either at cabin pressure, or may be used for transitional pressure from high-pressure habitats), and a nominal unpressurized second compartment where the suits will be kept for normal operations. The advantages include quicker egress / ingress, capacity for 'shirt sleeve' suit maintenance, and portability of the entire unit.