Search NASA⌕ Search

SEARCH · Search NASA

Results for “Behavior analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

On the Onset of Plasticity: Determination of Strength and Ductility

The analysis of the work hardening variation with stress reveals insight to operative stress-strain mechanisms in material systems. The onset of plasticity can be assessed and related to ensuing plastic deformation up to the structural instability using one constitutive relationship that incorporates both behaviors of rapid work hardening (Stage 3) and the asymptotic leveling of stress (Stage 4). Results are presented for the mechanical behavior analysis of Ti-6Al-4V wherein the work hardening variation of Stages 3 and 4 are found to: be dependent through a constitutive relationship; be useful in a Hall-Petch formulation of yield strength; and provide the basis for a two point-slope fit method to model the experimental work hardening and stress-strain behavior.

36 MATERIALS SCIENCE↗

Development of tritium technologies at KAERI

Korea has been operating a CANDU nuclear power plant since 1983. Tritium generated in the heavy water of the plant is removed by the Wolsong TRF (Tritium Removal Facility) and measurement campaigns of tritium near the power plant have shown the efficiency of the TRF system. The HANARO reactor uses heavy water as both reflector and moderator. In HANARO the tritiated water removal system consists of compressors, condensers, and adsorption beds. A tritium behavior analysis code (TRIBAC) for a Very High Temperature Gas-Cooled Reactor (VHTR) is under development at KAERI. The TRIBAC computer software has been equipped with models for tritium production, purification, and leakage, as well as chemisorption and tritium behavior, in the hydrogen production system. Korea takes part into the ITER program and is responsible for the supply of an SDS (Tritium Storage and Delivery System). Within this program Korea has launched an experimental program to study the physico-chemical properties of metal and their hydrides in which hydrogen isotope gases can be stored and removed safely.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Analysis of Autopilot Behavior

Aviation and cognitive science researchers have identified situations in which the pilot's expectations for behavior of autopilot avionics are not matched by the actual behavior of the avionics. These "automation surprises" have been attributed to differences between the pilot's model of the behavior of the avionics and the actual behavior encoded in the avionics software. A formal technique is described for the analysis and measurement of the behavior of the cruise pitch modes of a modern Autopilot. The analysis characterizes the behavior of the Autopilot as situation-action rules. The behavior of the cruise pitch mode logic for a contemporary modern Autopilot was found to include 177 rules, including Level Change (23), Vertical Speed (16), Altitude Capture (50), and Altitude Hold (88). These rules are determined based on the values of 62 inputs. Analysis of the rule-based model also shed light on the factors cited in the literature as contributors to "automation surprises."

Sherry, Lance↗

Physical properties of the layered $\mathcal{f}$-electron van der Waals magnet Ce 2 Te 5

Here. we report a detailed study of the magnetic, transport, and thermodynamic properties of Ce 2 Te 5 single crystals, a layered $\mathcal{f}$-electron van der Waals magnet. Four consecutive transitions at ~5.2, 2.1, 0.9, and 0.4 K were observed in the ac-plane electrical resistivity $\rho(T)$, which were further confirmed in specific heat $C_\text{p}(T)$ measurements. Analysis of the magnetic susceptibility $\chi(T)$, the magnetic-field variation of $\rho(T)$, and the increase of the first transition temperature ($T_c$ ~ 5.2 K) with applied magnetic field indicates ferromagnetic order, while the decrease of the other transitions with field suggests different states with dominant antiferromagnetic interactions below $T_2$ ~ 2.1 K, $T_3$ ~ 0.9 K, and $T_4$ = 0.4 K. Critical behavior analysis around Tc that gives critical exponents $\beta$ = 0.31(2), $\gamma$ = 0.99(2), $\delta$ = 4.46(1), and $T_c$ = 5.32(1) K indicates that Ce 2 Te 5 shows a three-dimensional magnetic critical behavior. Moreover, the Hall resistivity ρxy indicates that Ce2Te5 is a multiband system with a relatively high electron mobility ~2900 cm 2 V –1 s –1 near $T_c$, providing further opportunities for future device applications.

36 MATERIALS SCIENCE↗

Modeling and Prediction of Wildfire Hazard in Southern California, Integration of Models with Imaging Spectrometry

Large urban wildfires throughout southern California have caused billions of dollars of damage and significant loss of life over the last few decades. Rapid urban growth along the wildland interface, high fuel loads and a potential increase in the frequency of large fires due to climatic change suggest that the problem will worsen in the future. Improved fire spread prediction and reduced uncertainty in assessing fire hazard would be significant, both economically and socially. Current problems in the modeling of fire spread include the role of plant community differences, spatial heterogeneity in fuels and spatio-temporal changes in fuels. In this research, we evaluated the potential of Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) and Airborne Synthetic Aperture Radar (AIRSAR) data for providing improved maps of wildfire fuel properties. Analysis concentrated in two areas of Southern California, the Santa Monica Mountains and Santa Barbara Front Range. Wildfire fuel information can be divided into four basic categories: fuel type, fuel load (live green and woody biomass), fuel moisture and fuel condition (live vs senesced fuels). To map fuel type, AVIRIS data were used to map vegetation species using Multiple Endmember Spectral Mixture Analysis (MESMA) and Binary Decision Trees. Green live biomass and canopy moisture were mapped using AVIRIS through analysis of the 980 nm liquid water absorption feature and compared to alternate measures of moisture and field measurements. Woody biomass was mapped using L and P band cross polarimetric data acquired in 1998 and 1999. Fuel condition was mapped using spectral mixture analysis to map green vegetation (green leaves), nonphotosynthetic vegetation (NPV; stems, wood and litter), shade and soil. Summaries describing the potential of hyperspectral and SAR data for fuel mapping are provided by Roberts et al. and Dennison et al. To utilize remotely sensed data to assess fire hazard, fuel-type maps were translated into standard fuel models accessible to the FARSITE fire spread simulator. The FARSITE model and BEHAVE are considered industry standards for fire behavior analysis. Anderson level fuels map, generated using a binary decision tree classifier are available for multiple dates in the Santa Monica Mountains and at least one date for Santa Barbara. Fuel maps that will fill in the areas between Santa Barbara and the Santa Monica Mountains study sites are in progress, as part of a NASA Regional Earth Science Application Center, the Southern California Wildfire Hazard Center. Species-level maps, were supplied to fire managing agencies (Los Angeles County Fire, California Department of Forestry). Research results were published extensively in the refereed and non-refereed literature. Educational outreach included funding of several graduate students, undergraduate intern training and an article featured in the California Alliance for Minorities Program (CAMP) Quarterly Journal.

Roberts, Dar A.↗

Feeding state-dependent neuropeptidergic modulation of reciprocally interconnected inhibitory neurons biases sensorimotor decisions in Drosophila

Abstract An animal’s feeding state changes its behavioral priorities and thus influences even nonfeeding-related decisions. How the feeding state information is transmitted to nonfeeding-related circuits and what circuit mechanisms are involved in biasing nonfeeding-related decisions remain open questions. By combining calcium imaging, neuronal manipulations, behavioral analysis and computational modeling, we determined that the competition between different aversive responses to mechanical cues is biased by changes in the feeding state. We found that this effect is achieved by the differential modulation of two different types of reciprocally connected inhibitory neurons promoting opposing actions. This modulation results in a more frequent active type of response and, less frequently, a protective type of response if larvae are fed sugar than when they are fed a balanced diet. Information about the internal state is conveyed to inhibitory neurons through homologs of the vertebrate neuropeptide Y, which is known to be involved in regulating feeding behavior.

Science & Technology - Other Topics↗

A Change Impact Analysis to Characterize Evolving Program Behaviors

Change impact analysis techniques estimate the potential effects of changes made to software. Directed Incremental Symbolic Execution (DiSE) is an intraprocedural technique for characterizing the impact of software changes on program behaviors. DiSE first estimates the impact of the changes on the source code using program slicing techniques, and then uses the impact sets to guide symbolic execution to generate path conditions that characterize impacted program behaviors. DiSE, however, cannot reason about the flow of impact between methods and will fail to generate path conditions for certain impacted program behaviors. In this work, we present iDiSE, an extension to DiSE that performs an interprocedural analysis. iDiSE combines static and dynamic calling context information to efficiently generate impacted program behaviors across calling contexts. Information about impacted program behaviors is useful for testing, verification, and debugging of evolving programs. We present a case-study of our implementation of the iDiSE algorithm to demonstrate its efficiency at computing impacted program behaviors. Traditional notions of coverage are insufficient for characterizing the testing efforts used to validate evolving program behaviors because they do not take into account the impact of changes to the code. In this work we present novel definitions of impacted coverage metrics that are useful for evaluating the testing effort required to test evolving programs. We then describe how the notions of impacted coverage can be used to configure techniques such as DiSE and iDiSE in order to support regression testing related tasks. We also discuss how DiSE and iDiSE can be configured for debugging finding the root cause of errors introduced by changes made to the code. In our empirical evaluation we demonstrate that the configurations of DiSE and iDiSE can be used to support various software maintenance tasks

Rungta, Neha Shyam↗

Capability Building Progression of an Insider Threat Mitigation Program at an International Research Reactor

The nuclear industry recognizes the difficulties involved in developing effective managerial and leadership skills in a highly technical and proficient workforce such as that found in nuclear facilities. Implementing an insider threat mitigation program (ITMP) within the nuclear industry is a complex and ongoing process that demands a comprehensive understanding of human behavior, an organization’s security culture, and rigorous regulatory requirements yet also accounts for facility characteristics, physical security, material flow, and activities involving nuclear material. Given the high-consequence nature of research reactor operations, even minor lapses can lead to safety, security, and reputational risks. An effective ITMP requires a defense-in-depth approach that incorporates behavioral analysis, robust vetting procedures, continuous monitoring, and cross-disciplinary coordination. It must also promote a culture of vigilance and accountability at all levels up to and including executive leadership but be flexible enough to adapt to evolving global threats and technological advances. Insider threat mitigation is not a one-time effort but rather a sustained commitment to excellence in safety and security. Establishing a culture in which personnel proactively report incidents and issues that could affect nuclear safety and security is vital to maintaining a safe and secure operational environment. This document was developed to guide senior management and research reactor organizations in creating comprehensive programs to effectively manage and mitigate insider threat behaviors and actions. It focuses on the key pillars of an effective ITMP, including the national legal framework, security culture, preventive and protective measures, cyber security, and performance evaluation. By using a systematic approach during implementation, facilities can foster environments conducive to insider threat detection and support long-term program sustainability. The document also provides strategies for improving communication across all levels of an organization, helping to eliminate barriers that hinder the development of robust ITMPs and enhance overall security culture. In today’s organizations, the concept of leveraging safety and security culture lessons to facilitate knowledge transfer is rapidly evolving to expedite insider threat management and security culture improvements. This document outlines the rationale for evaluating an ITMP based on national customs, culture, and stakeholders. The elements are all germane to reliability and trustworthiness and relate to security concerns that states may encounter. The document focuses not only on individual perceptions regarding security issues and capability building but also on team building and how to resolve concerns. The implementers of a facility’s ITMP may zero in on indicators of insider threats within their enterprise. This material will benefit organizations when it is applied using a systematic and structured approach as demonstrated throughout the document.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

A Bayesian approach to time-domain photonic Doppler velocimetry analysis

Photonic Doppler velocimetry (PDV) is an established technique for measuring the velocities of fast-moving surfaces in high-energy-density experiments. In the standard approach to PDV analysis, the short-time Fourier transform (STFT) is used to generate a spectrogram from which the velocity history of the target is inferred. The user chooses the form, duration, and separation of the window function. Here, in this study, we present a Bayesian approach to infer the velocity directly from the PDV oscilloscope trace, without using the spectrogram for analysis. This is clearly a difficult inference problem due to the highly periodic nature of the data, but we find that with carefully chosen prior distributions for the model parameters, we can accurately recover the injected velocity from synthetic data. We validate this method using PDV data collected at the STAR two-stage light gas gun at Sandia National Laboratories, recovering shock-front velocities in quartz that are consistent with those inferred using the STFT-based approach and are interpolated across regions of low signal-to-noise data. Although this method does not rely on the same user choices as the STFT, we caution that it can be prone to misspecification if the chosen model is not sufficient to capture the velocity behavior. Analysis using posterior predictive checks can be used to establish whether a better model is required, although more complex models come with additional computational cost, often taking more than several hours to converge when sampling the Bayesian posterior. We, therefore, recommend it be viewed as a complementary method to that of the STFT-based approach.

Allison, James R. [First Light Fusion Ltd., Yarnto↗

Coastal Ohio Wind Project

The Coastal Ohio Wind Project intends to address problems that impede deployment of wind turbines in the coastal and offshore regions of Northern Ohio. The project evaluates different wind turbine designs and the potential impact of offshore turbines on migratory and resident birds by developing multidisciplinary research, which involves wildlife biology, electrical and mechanical engineering, and geospatial science. Firstly, the project conducts cost and performance studies of two- and three-blade wind turbines using a turbine design suited for the Great Lakes. The numerical studies comprised an analysis and evaluation of the annual energy production of two- and three-blade wind turbines to determine the levelized cost of energy. This task also involved wind tunnel studies of model wind turbines to quantify the wake flow field of upwind and downwind wind turbine-tower arrangements. The experimental work included a study of a scaled model of an offshore wind turbine platform in a water tunnel. The levelized cost of energy work consisted of the development and application of a cost model to predict the cost of energy produced by a wind turbine system placed offshore. The analysis found that a floating two-blade wind turbine presents the most cost effective alternative for the Great Lakes. The load effects studies showed that the two-blade wind turbine model experiences less torque under all IEC Standard design load cases considered. Other load effects did not show this trend and depending on the design load cases, the two-bladed wind turbine showed higher or lower load effects. The experimental studies of the wake were conducted using smoke flow visualization and hot wire anemometry. Flow visualization studies showed that in the downwind turbine configuration the wake flow was insensitive to the presence of the blade and was very similar to that of the tower alone. On the other hand, in the upwind turbine configuration, increasing the rotor blade angle of attack reduced the wake size and enhanced the vortices in the flow downstream of the turbine-tower compared with the tower alone case. Mean and rms velocity distributions from hot wire anemometer data confirmed that in a downwind configuration, the wake of the tower dominates the flow, thus the flow fields of a tower alone and tower-turbine combinations are nearly the same. For the upwind configuration, the mean velocity shows a narrowing of the wake compared with the tower alone case. The downwind configuration wake persisted longer than that of an upwind configuration; however, it was not possible to quantify this difference because of the size limitation of the wind tunnel downstream of the test section. The water tunnel studies demonstrated that the scale model studies could be used to adequately produce accurate motions to model the motions of a wind turbine platform subject to large waves. It was found that the important factors that affect the platform is whether the platform is submerged or surface piercing. In the former, the loads on the platform will be relatively reduced whereas in the latter case, the structure pierces the wave free surface and gains stiffness and stability. The other important element that affects the movement of the platform is depth of the sea in which the wind turbine will be installed. Furthermore, the wildlife biology component evaluated migratory patterns by different monitoring systems consisting of marine radar, thermal IR camera and acoustic recorders. The types of radar used in the project are weather surveillance radar and marine radar. The weather surveillance radar (1988 Doppler), also known as Next Generation Radar (NEXRAD), provides a network of weather stations in the US. Data generated from this network were used to understand general migratory patterns, migratory stopover habitats, and other patterns caused by the effects of weather conditions. At a local scale our marine radar was used to complement the datasets from NEXRAD and to collect additional monitoring parameters such as passage rates, flight paths, flight directions, and flight altitudes of nocturnal migrating species. Our work focused on the design and development of custom built marine radar that used t-bar and parabolic dish antennas. The marine radar used in the project was Furuno (XANK250) which was coupled with a XIR3000B digitizing card from Russell Technologies for collection of the radar data. The radar data was processed by open source radR processing software using different computational techniques and methods. Additional data from thermal IR imaging cameras were collected to detect heat emitted from objects and provide information on movements of birds and bats, data which we used for different animal flight behavior analysis. Lastly, the data from the acoustic recorders were used to provide the number of bird calls for assessing patterns and peak passage rates during migration. The development of the geospatial database included collection of different data sources that are used to support offshore wind turbine development. Many different data sets were collected and organized using initial version of web-based repository software tools that can accommodate distribution of rectified pertinent data sets such as the lake depth, lake bottom engineering parameters, extent of ice, navigation pathways, wind speed, important bird habitats, fish efforts and other layers that are relevant for supporting robust offshore wind turbine developments. Additional geospatial products developed during the project included few different prototypes for offshore wind farm suitability which can involve different stakeholders and participants for solving complex planning problems and building consensus. Some of the prototypes include spatial decision support system (SDSS) for collaborative decision making, a web-based Participatory Geographic Information System (PGIS) framework for evaluating importance of different decision alternatives using different evaluation criteria, and an Android application for collection of field data using mobile and tablet devices . In summary, the simulations of two- and three-blade wind turbines suggested that two-bladed machines could produce comparable annual energy as the three-blade wind turbines but have a lighter tower top weight, which leads to lower cost of energy. In addition, the two-blade rotor configuration potentially costs 20% less than a three blade configuration that produces the same power at the same site. The cost model analysis predicted a potential cost savings of approximately 15% for offshore two-blade wind turbines. The foundation design for a wind turbine in Lake Erie is likely to be driven by ice loads based on the currently available ice data and ice mechanics models. Hence, for Lake Eire, the cost savings will be somewhat smaller than the other lakes in the Great Lakes. Considering the size of cranes and vessels currently available in the Great Lakes, the cost optimal wind turbine size should be 3 MW, not larger. The surveillance data from different monitoring systems suggested that bird and bat passage rates per hour were comparable during heavy migrations in both spring and fall seasons while passage rates were significantly correlated to wind directions and wind speeds. The altitude of migration was higher during heavy migrations and higher over water relative to over land. Notable portions of migration on some spring nights occurred parallel the shoreline, often moving perpendicular to southern winds. The birds approaching the Western basin have a higher propensity to cross than birds approaching the Central basin of Lake Erie and as such offshore turbine development might be a better option further east towards Cleveland than in the Western basin. The high stopover density was more strongly associated with migration volume the following night rather than the preceding night. The processed mean scalar wind speeds with temporal resolutions as fine as 10-minute intervals near turbine height showed that August is the month with the weakest winds while December is the month, which typically has the strongest winds. The ice data suggests that shallow western basin of Lake Erie has higher ice cover duration many times exceeding 90 days during some winters.

17 WIND ENERGY↗

Evaluating Pressure‐dependent Discharge Behavior of Foil Versus In situ Plated Lithium Metal Anodes in Solid‐State Batteries

Abstract Anode‐free manufacturing of solid‐state batteries (SSBs) shows promise to maximize energy density by eliminating excess lithium (Li) and simplifying battery production. However, high reversibility during discharge (stripping of Li) is necessary for long‐lifetime SSBs with a limited Li reservoir. Further, the plastic flow of Li changes depending on the Li thickness, leading to possible differences in discharge performance under stack pressure. This work investigates the pressure‐dependent discharge performance of anode‐free manufactured SSBs with in situ plated Li and compares the performance to that of conventional thick Li foil cells. Distinct stripping behavior is observed at low pressures (0–1 MPa), where Li diffusivity and initial interfacial contact may control accessible capacity, compared to high pressures (3–10 MPa) where mechanical deformation of Li likely governs stripping behavior. Analysis of impedance spectra collected during stripping shows that additional stack pressure delays the formation of deep, as opposed to lateral, voids in the Li anode. These results provide insights to guide the transition from thick Li foil anodes to anode‐free manufactured SSBs.

Haslam, Catherine G.↗

Pulsed laser deposition to synthesize the bridge structure of artificial nacre: Comparison of nano- and femtosecond lasers

Nature offers inspiration to new adaptive technologies that allow us to build amazing shapes and structures such as nacre using synthetic materials. Consequently, we have designed a pulsed laser ablation manufacturing process involving thin film deposition and micro-machining to create hard/soft layered 'brick-bridge-mortar' nacre of AlMgB{sub 14} (hard phase) with Ti (soft phase). In this paper, we report pulsed laser deposition (PLD) to mimic brick and bridge structures of natural nacre in AlMgB{sub 14}. Particulate formation inherent in PLD is exploited to develop the bridge structure. Mechanical behavior analysis of the AlMgB{sub 14}/Ti system revealed that the brick is to be 250 nm thick, 9 {mu}m lateral dimensions while the bridge (particle) is to have a diameter of 500 nm for a performance equivalent to natural nacre. Both nanosecond (ns) and femtosecond (fs) pulsed lasers were employed for PLD in an iterative approach that involves varying pulse energy, pulse repetition rate, and target-to-substrate distance to achieve the desired brick and bridge characteristics. Scanning electron microscopy, x-ray photoelectron spectroscopy, and optical profilometer were used to evaluate the film thickness, particle size and density, stoichiometry, and surface roughness of thin films. Results indicated that both ns-pulsed and fs-pulsed lasers produce the desired nacre features. However, each laser may be chosen for different reasons: fs-pulsed laser is preferred for much shorter deposition time, better stoichiometry, uniform-sized particles, and uniform film thickness, while ns-pulsed laser is favored for industrial acceptance, reliability, ease of handling, and low cost.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Metal-semiconductor-transition observed in Bi{sub 2}Ca(Sr, Ba){sub 2}Co{sub 2}O{sub 8+δ} single crystals

Electrical property evolution of Bi{sub 2}AE{sub 2}Co{sub 2}O{sub 8+δ} single crystals (AE = Ca, Sr and Ba) is systematically explored. When AE changes from Ca to Ba, the electrical property of Bi{sub 2}Ca{sub 2}Co{sub 2}O{sub 8+δ} and Bi{sub 2}Sr{sub 2}Co{sub 2}O{sub 8+δ} demonstrates semiconductor-like properties. But Bi{sub 2}Ba{sub 2}Co{sub 2}O{sub 8+δ} shows the metallic behavior. Analysis of temperature-dependent resistance substantiates that from metallic Bi{sub 2}Ba{sub 2}Co{sub 2}O{sub 8+δ} to semiconductor-like Bi{sub 2}Sr{sub 2}Co{sub 2}O{sub 8+δ} can be attributed to Anderson localization. However the semiconductor behaviour of Bi{sub 2}Sr{sub 2}Co{sub 2}O{sub 8+δ} and Bi{sub 2}Ca{sub 2}Co{sub 2}O{sub 8+δ} is related to electronic correlations effect that is inferred by large negative magnetoresistance (∼70%). The theoretical electronic structures and valence X-ray photoemission spectroscopy substantiate that there is a relative large density of state around Fermi level in Bi{sub 2}Ba{sub 2}Co{sub 2}O{sub 8+δ} compared with other two compounds. It suggests that Bi{sub 2}Ba{sub 2}Co{sub 2}O{sub 8+δ} is more apt to be metal in this material system.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetic properties and coercivity mechanism of Sm{sub 1-x}Pr{sub x}Co{sub 5} (x=0-0.6) nanoflakes prepared by surfactant-assisted ball milling

Sm{sub 1-x}Pr{sub x}Co{sub 5} (x=0-0.6) nanoflakes with CaCu{sub 5} structure were successfully prepared by surfactant-assisted high-energy ball milling (SAHEBM). The crystal structure and magnetic properties of Sm{sub 1-x}Pr{sub x}Co{sub 5} (x=0-0.6) nanoflakes were studied by X-ray diffraction and vibrating sample magnetometer. Effects of Pr addition on the structure, magnetic properties and coercivity mechanism of Sm{sub 1-x}Pr{sub x}Co{sub 5} nanoflakes were systematically investigated. XRD results show that all the nanoflakes have a hexagonal CaCu{sub 5}-type (Sm, Pr){sub 1}Co{sub 5} main phase and the (Sm, Pr){sub 2}Co{sub 7} impurity phase, and all of the samples exhibit a strong (00l) texture after magnetic alignment. As the Pr content increases, remanence firstly increases, then slightly reduced, while anisotropy field (H{sub A}) and H{sub ci} of decrease monotonically. Maximum energy product [(BH){sub max}] of the flakes increases first, peaks at 24.4 MGOe with Pr content of x = 0.4, then drops again. Magnetization behavior analysis indicate that the coercivity mechanism is mainly controlled by inhomogeneous domain wall pinning, and the pinning strength weakens with the increased Pr content, suggesting the great influence of H{sub A} on the coercivity of flakes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Anisotropic magnetocaloric effect and critical behavior in CrCl 3

We report anisotropic magnetocaloric effect and magnetic critical behavior in the van der Waals crystal CrCl 3 . The maximum magnetic entropy change $-ΔS^{max}_M ~ 14.6 J kg -1 K -1 and the relative cooling power RCP ~ 340.3 J kg -1 near T c with a magnetic field change of 5 T are much larger when compared to CrI 3 or CrBr 3 . The rescaled ΔS M (T, H) curves collapse onto a universal curve, confirming the second-order ferromagnetic transition. Finally, further critical behavior analysis around T c presents a set of critical exponents β = 0.28 (1) with T c = 19.4 (2) K, γ = 0.89 (1) with T c = 18.95 (8) K, and δ = 4.6 (1) at T c = 19 K , which are close to those of the theoretical tricritical mean-field model.

2-dimensional systems↗

Anisotropic magnetocaloric effect and critical behavior in CrSbSe3

In this work, we report anisotropic magnetocaloric effect and critical behavior in a quasi-one-dimensional ferromagnetic CrSbSe 3 single crystal. The maximum magnetic entropy change - Δ S M max is 2.16 J kg - 1 K - 1 for the easy a axis (2.03 J kg - 1 K - 1 for the hard b axis) and the relative cooling power RCP is 163.1 J kg - 1 for the easy a axis (142.1 J kg - 1 for the hard b axis) near T c with a magnetic field change of 50 kOe. The magnetocrystalline anisotropy constant K u is estimated to be 148.5 kJ m - 3 at 10 K, decreasing to 39.4 kJ m - 3 at 70 K. The rescaled Δ S M ( T , H ) curves along all three axes collapse onto a universal curve, respectively, confirming the second-order ferromagnetic transition. Further critical behavior analysis around T c ~ 70 K gives that the critical exponents β = 0.26 ( 1 ) , γ = 1.32 ( 2 ) , and δ = 6.17 ( 9 ) for H ∥ a , while β = 0.28 ( 2 ) , γ = 1.02 ( 1 ) , and δ = 4.14 ( 16 ) for H ∥ b . The determined critical exponents suggest that the anisotropic magnetic coupling in CrSbSe 3 is strongly dependent on orientations of the applied magnetic field.

2-dimensional systems↗

Three-dimensional Ising ferrimagnetism of Cr-Fe-Cr trimers in FeCr2Te4

We carried out a comprehensive study of magnetic critical behavior in single crystals of ternary chalcogenide Fe Cr 2 Te 4 that undergoes a ferrimagnetic transition below T c ~ 123 K. Detailed critical behavior analysis and scaled magnetic entropy change indicate a second-order ferrimagnetic transition. Critical exponents β = 0.30 ( 1 ) with T c = 122.4 ( 5 ) K , γ = 1.22 ( 1 ) with T c = 122.8 ( 1 ) K , and δ = 4.24 ( 2 ) at T c ~ 123 K suggest that the spins approach the three-dimensional Ising ( β = 0.325 , γ = 1.24 , and δ = 4.82 ) model coupled with attractive long-range interactions between spins that decay as J ( r ) ≈ r - 4.88 . Our results suggest that the ferrimagnetism in Fe Cr 2 Te 4 is due to itinerant ferromagnetism among the antiferromagnetically coupled Cr-Fe-Cr trimers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Single crystal growth and thermoelectric properties of Nowotny chimney-ladder compound Fe 2 Ge 3

Fe 2 Ge 3 with an incommensurate Nowotny chimney-ladder (NCL) structure is a promising material for thermoelectric applications due to its low thermal conductivity. Previous experimental studies on Fe 2 Ge 3 have mainly focused on polycrystalline samples, resulting in a limited understanding of the material's intrinsic thermoelectric properties and the underlying causes of its low thermal conductivity. Here we report the synthesis and thermoelectric properties of single crystalline Fe 2 Ge 3 . Millimeter-sized Fe 2 Ge 3 single crystals grown by the chemical vapor transport method enable the study of the intrinsic thermoelectric properties. The Seebeck coefficient of Fe 2 Ge 3 is negative and its magnitude increases linearly with temperature, showing a degenerate n-type semiconductor behavior. Analysis of the electrical resistivity and specific heat data indicates the existence of an Einstein mode with a characteristic temperature of about 60 K, suggesting the presence of low-energy optical phonons. Further, the thermal conductivity of Fe 2 Ge 3 along the c axis is as low as 1.9Wm -1 K -1 at 300 K and exhibits a nearly temperature-independent characteristic, which is distinct from the previous theoretical calculations with a stronger temperature dependence. The low thermal conductivity may be attributed to the scattering of acoustic phonons by low-energy optical modes and the presence of non-extended diffuson modes, as reported in another NCL compound, MnSi 1.74 . This study provides valuable insights into the electrical and thermal properties of Fe 2 Ge 3 , which can open up possibilities for future advances in thermoelectric applications.

36 MATERIALS SCIENCE↗