Results for “CAPTURE EFFECT” — Page 5

NASA NTRSDate not supplied

Thermal Model of Ice Growth in Vacuum for Lunar Water Production

To support NASA’s goal of sustained lunar presence, the use of in-situ resource utilization will reduce launch weight and frequency of resupply missions. With the discovery of water in the permanently shadowed regions of the moon, the prospect of harvesting water has generated particular interest. A more fundamental understanding of water storage and capture in lunar conditions is necessary for effective and efficient water capture and transport. The present study derives a thermal model for ice height, heat flux, chamber pressure, and mass flow rate in sub-atmospheric pressures below the triple point. The thermal model compares ice layer height against the results of the experiment at two pressures (300 Pa and 500 Pa) and temperatures from -18°C to -3°C. The thermal model predicts the trends seen experimentally with an overall root mean square error of 0.1135 cm and coefficient of efficiency of 0.994, indicating the model predicts the experimental results. The thermal model can be utilized to examine the impacts of varying pressure, temperature, and cold plate area to determine the most effective ice growth conditions for efficient capture of water on the lunar surface. The thermal model will provide a useful tool for NASA in the design of the lunar ice tanker and shows the promise of effective capture water on the lunar surface.

Ice growth↗

NASA NTRSDate not supplied

Thermal Model of Ice Growth in Vacuum for Lunar Water Production

To support NASA’s goal of sustained lunar presence, the use of in-situ resource utilization will reduce launch weight and frequency of resupply missions. With the discovery of water in the permanently shadowed regions of the moon, the prospect of harvesting water has generated particular interest. A more fundamental understanding of water storage and capture in lunar conditions is necessary for effective and efficient water capture and transport. The present study derives a thermal model for ice height, heat flux, chamber pressure, and mass flow rate in sub-atmospheric pressures below the triple point. The thermal model compares ice layer height against the results of the experiment at two pressures (300 Pa and 500 Pa) and temperatures from -18°C to -3°C. The thermal model predicts the trends seen experimentally with an overall root mean square error of 0.1135 cm and coefficient of efficiency of 0.994, indicating the model predicts the experimental results. The thermal model can be utilized to examine the impacts of varying pressure, temperature, and cold plate area to determine the most effective ice growth conditions for efficient capture of water on the lunar surface. The thermal model will provide a useful tool for NASA in the design of the lunar ice tanker and shows the promise of effective capture water on the lunar surface.

Ice growth↗

NASA NTRS2016

A Method for Improving Hotspot Directional Signatures in BRDF Models Used for MODIS

The semi-empirical, kernel-driven, linear RossThick-LiSparseReciprocal (RTLSR) Bidirectional Reflectance Distribution Function (BRDF) model is used to generate the routine MODIS BRDFAlbedo product due to its global applicability and the underlying physics. A challenge of this model in regard to surface reflectance anisotropy effects comes from its underestimation of the directional reflectance signatures near the Sun illumination direction; also known as the hotspot effect. In this study, a method has been developed for improving the ability of the RTLSR model to simulate the magnitude and width of the hotspot effect. The method corrects the volumetric scattering component of the RTLSR model using an exponential approximation of a physical hotspot kernel, which recreates the hotspot magnitude and width using two free parameters (C(sub 1) and C(sub 2), respectively). The approach allows one to reconstruct, with reasonable accuracy, the hotspot effect by adjusting or using the prior values of these two hotspot variables. Our results demonstrate that: (1) significant improvements in capturing hotspot effect can be made to this method by using the inverted hotspot parameters; (2) the reciprocal nature allow this method to be more adaptive for simulating the hotspot height and width with high accuracy, especially in cases where hotspot signatures are available; and (3) while the new approach is consistent with the heritage RTLSR model inversion used to estimate intrinsic narrowband and broadband albedos, it presents some differences for vegetation clumping index (CI) retrievals. With the hotspot-related model parameters determined a priori, this method offers improved performance for various ecological remote sensing applications; including the estimation of canopy structure parameters.

airborne measurements↗

NASA NTRS2020

Inter-species molecular attraction effect in the development of a two-species mixing layer

Simulations of fluid mixing occurring at high-pressures mandate the use of real-fluid equations of state to capture the effect of boh intermolecular repulsive forces and attractive forces which are neglected in perfect gases. Dedicated mixing rules account for these forces by providing a generic mapping of the mixture state-space onto a pure fluid domain. However, the specific inter-species molecular forces depend on the particular characteristics of the molecular pairs under consideration, and typically require the knowledge of binary interaction coefficients k_{αβ}. The impact of k_{αβ} on a flow field is as of now unclear; further, k_{αβ} is unknown for many molecular pairs and when unknown, set to be null. This study addresses the impact of k_{αβ} on the temporal evolution of a real-fluid mixing layer and uses Direct Numerical Simulation (DNS) to explore this impact. The results show differences between augmented attraction (k_{αβ}<0) and diminished attraction (k_{αβ}>0), affecting both fluid dynamics and diffusion processes. Specifically, in a binary mixing layer, it is observed that augmented attraction leads to delayed transition and mixing layer growth, manifested in the momentum layer thickness. The fractal dimension, which is a manifestation of interface corrugation, is calculated. These results provide an hitherto undocumented mechanism affecting the development of mixing layers.

Banuti, Daniel↗

NASA NTRSDate not supplied

Particle Interaction Physics Model Formulation for Plume-Surface Interaction Erosion and Cratering

The Predictive Simulation Capability development team of the STMD Game Changing Development sponsored PSI project is implementing computational simulation capability for the efficient and accurate prediction of Plume-Surface Interaction induced surface erosion and cratering in Martian and Lunar environments. The status of the Focus Area 3 of the PSI project in the generation and efficient application of accurate soil particle composition modeling in the Gas-Granular Flow Solver (GGFS) computational framework is presented. The process of constitutive closure model database generation using DEM particle interaction modeling for capturing the effects of irregular particle shape and poly-disperse mixture distribution effects is outlined. This capability has now been ported to NASA supercomputer assets and NASA engineers successfully demonstrated technology and skillset transfer in model generation for spherical and irregularly shaped, mono-disperse and bi-disperse mixture compositions. Assessment of the computational efficiency and practicality of the academic serially executed DEM tools on NASA supercomputers identified the need to migrate to a DEM framework capable of performing parallel simulations in a simultaneous process orchestrated in an automated setup, execution, database extraction, and dataset delivery ready for application simulations. The LIGGGHTS DEM toolset has been selected as the most suitable tool to migrate the DEM simulations. Once the soil model generation process is implemented, models capturing the shape and poly-dispersity effects will be generated to perform much refined validation simulations against the experiments performed under the PSI project. The application readiness of the soil models currently operational in GGFS was presented for the example of a full scale, 3-D simulation of the plume induced erosion and crater formation of the Apollo LM at an elevation of 5m above ground in a low pressure, near vacuum background.

Peter A Liever↗

NASA NTRSDate not supplied

Particle Interaction Physics Model Formulation for Plume-Surface Interaction Erosion and Cratering

The Predictive Simulation Capability development team of the STMD Game Changing Development sponsored PSI project is implementing computational simulation capability for the efficient and accurate prediction of Plume-Surface Interaction induced surface erosion and cratering in Martian and Lunar environments. The status of the Focus Area 3 of the PSI project in the generation and efficient application of accurate soil particle composition modeling in the Gas-Granular Flow Solver (GGFS) computational framework is presented. The process of constitutive closure model database generation using DEM particle interaction modeling for capturing the effects of irregular particle shape and poly-disperse mixture distribution effects is outlined. This capability has now been ported to NASA supercomputer assets and NASA engineers successfully demonstrated technology and skillset transfer in model generation for spherical and irregularly shaped, mono-disperse and bi-disperse mixture compositions. Assessment of the computational efficiency and practicality of the academic serially executed DEM tools on NASA supercomputers identified the need to migrate to a DEM framework capable of performing parallel simulations in a simultaneous process orchestrated in an automated setup, execution, database extraction, and dataset delivery ready for application simulations. The LIGGGHTS DEM toolset has been selected as the most suitable tool to migrate the DEM simulations. Once the soil model generation process is implemented, models capturing the shape and poly-dispersity effects will be generated to perform much refined validation simulations against the experiments performed under the PSI project. The application readiness of the soil models currently operational in GGFS was presented for the example of a full scale, 3-D simulation of the plume induced erosion and crater formation of the Apollo LM at an elevation of 5m above ground in a low pressure, near vacuum background.

Peter A Liever↗

NASA NTRS1984

Boundary layer effects on particle impaction and capture

The inertial impaction and deposition of small particles on larger bodies with viscous boundary layers are considered theoretically, in a detailed comment on a paper by Menguturk et al. (1983). Topics addressed include cushion effects, the dimensionless groups corresponding to the diameter range (3-6 microns) examined by Menguturk et al. in a numerical example, analogous effects of particle-gas energy and mass exchange in boundary layers, and the combined effects of particle inertia and diffusion. It is argued that the inertial effects can be characterized in terms of a body, boundary-layer, or sublayer Stokes number. In a reply by Menguturk et al., the focus is on the application of the theoretical model to the erosion of blade surfaces in large gas turbines; the Stokes number is found to be of limited practical value in these cases, because the particle motion is not primarily normal to the blade surfaces.

Rosner, D. E.↗

NASA NTRS2013

Using the Flow-3D General Moving Object Model to Simulate Coupled Liquid Slosh - Container Dynamics on the SPHERES Slosh Experiment: Aboard the International Space Station

The SPHERES Slosh Experiment (SSE) is a free floating experimental platform developed for the acquisition of long duration liquid slosh data aboard the International Space Station (ISS). The data sets collected will be used to benchmark numerical models to aid in the design of rocket and spacecraft propulsion systems. Utilizing two SPHERES Satellites, the experiment will be moved through different maneuvers designed to induce liquid slosh in the experiment's internal tank. The SSE has a total of twenty-four thrusters to move the experiment. In order to design slosh generating maneuvers, a parametric study with three maneuvers types was conducted using the General Moving Object (GMO) model in Flow-30. The three types of maneuvers are a translation maneuver, a rotation maneuver and a combined rotation translation maneuver. The effectiveness of each maneuver to generate slosh is determined by the deviation of the experiment's trajectory as compared to a dry mass trajectory. To fully capture the effect of liquid re-distribution on experiment trajectory, each thruster is modeled as an independent force point in the Flow-3D simulation. This is accomplished by modifying the total number of independent forces in the GMO model from the standard five to twenty-four. Results demonstrate that the most effective slosh generating maneuvers for all motions occurs when SSE thrusters are producing the highest changes in SSE acceleration. The results also demonstrate that several centimeters of trajectory deviation between the dry and slosh cases occur during the maneuvers; while these deviations seem small, they are measureable by SSE instrumentation.

Schulman, Richard↗

NASA NTRS1997

The Effect of Temperature Dependent Material Nonlinearities on the Response of Piezoelectric Composite Plates

Previously developed analytical formulations for piezoelectric composite plates are extended to account for the nonlinear effects of temperature on material properties. The temperature dependence of the composite and piezoelectric properties are represented at the material level through the thermopiezoelectric constitutive equations. In addition to capturing thermal effects from temperature dependent material properties, this formulation also accounts for thermal effects arising from: (1) coefficient of thermal expansion mismatch between the various composite and piezoelectric plies and (2) pyroelectric effects on the piezoelectric material. The constitutive equations are incorporated into a layerwise laminate theory to provide a unified representation of the coupled mechanical, electrical, and thermal behavior of smart structures. Corresponding finite element equations are derived and implemented for a bilinear plate element with the inherent capability to model both the active and sensory response of piezoelectric composite laminates. Numerical studies are conducted on a simply supported composite plate with attached piezoceramic patches under thermal gradients to investigate the nonlinear effects of material property temperature dependence on the displacements, sensory voltages, active voltages required to minimize thermal deflections, and the resultant stress states.

Lee, Ho-Jun↗

NASA NTRS1992

Computational study of the aerodynamics and control by blowing of asymmetric vortical flows over delta wings

The complicated flowfield around a rounded leading-edge delta wing was calculated at angles of attack and yaw with and without tangential leading-edge blowing, using thin-layer Navier-Stokes equations. The effectiveness of blowing for providing roll control at high angle of attack was illustrated, and the saturation effect of increased blowing was captured well. The effect of sideslip was shown to be analogous to asymmetric blowing.

Craig, Ken↗

NASA NTRS2008

Testing, Modeling and System Impact of Metabolic Heat Regenerated Temperature Swing Adsorption

Metabolic heat regenerated temperature swing adsorption (MTSA) technology is being developed for removal and rejection of carbon dioxide (CO2) and heat from a portable life support system (PLSS) to the Martian environment. Previously, hardware was built and tested to demonstrate using heat from simulated, dry ventilation loop gas to affect the temperature swing required to regenerate an adsorbent used for CO2 removal. New testing has been performed using a moist, simulated ventilation loop gas to demonstrate the effects of water condensing and freezing in the heat exchanger during adsorbent regeneration. In addition, thermal models of the adsorbent during regeneration were modified and calibrated with test data to capture the effect of the CO2 heat of desorption. Finally, MTSA impact on PLSS design was evaluated by performing thermal balances assuming a specific PLSS architecture. Results using NASA s Extravehicular Activity System Sizing Analysis Tool (EVAS_SAT), a PLSS system evaluation tool, are presented.

Lacomini, Christine S.↗

NASA NTRS1990

The effects of streamline curvature and swirl on turbulent flows in curved ducts

A technique for improving the numerical predictions of turbulent flows with the effect of streamline curvature is developed. Separated flows, the flow in a curved duct, and swirling flows are examples of flow fields where streamline curvature plays a dominant role. A comprehensive literature review on the effect of streamline curvature was conducted. New algebraic formulations for the eddy viscosity incorporating the kappa-epsilon turbulence model are proposed to account for various effects of streamline curvature. The loci of flow reversal of the separated flows over various backward-facing steps are employed to test the capability of the proposed turbulence model in capturing the effect of local curvature. The inclusion of the effect of longitudinal curvature in the proposed turbulence model is validated by predicting the distributions of the static pressure coefficients in an S-bend duct and in 180 degree turn-around ducts. The proposed turbulence model embedded with transverse curvature modification is substantiated by predicting the decay of the axial velocities in the confined swirling flows. The numerical predictions of different curvature effects by the proposed turbulence models are also reported.

Cheng, Chih-Hsiung↗

NASA NTRS1992

On turbulent flows dominated by curvature effects

A technique for improving the numerical predictions of turbulent flows with the effect of streamline curvature is developed. Separated flows and the flow in a curved duct are examples of flowfields where streamline curvature plays a dominant role. New algebraic formulations for the eddy viscosity incorporating the k-epsilon turbulence model are proposed to account for various effects of streamline curvature. The loci of flow reversal of the separated flows over various backward-facing steps are employed to test the capability of the proposed turbulence model in capturing the effect of local curvature.

Cheng, G. C.↗

NASA NTRS2012

SRMS Assisted Docking and Undocking for the Orbiter Repair Maneuver

As part of the Orbiter Repair Maneuver (ORM) planned for Return to Flight (RTF) operations, the Shuttle Remote Manipulator System (SRMS) must undock the Orbiter, maneuver it through a complex trajectory at extremely low rates, present it to an EVA crewman at the end of the Space Station Remote Manipulator System to perform the Thermal Protection System (TPS) repair, and then retrace back through the trajectory to dock the Orbiter with the Orbiter Docking System (ODS). The initial and final segments of this operation involve the interaction between the SRMS, ISS, Orbiter and ODS. Previously, a technique entitled "SRMS assisted docking" for installation of a payload to the ODS had been developed and was utilized for the Russian provided Docking Module on STS-74 during Shuttle-Mir missions and both the Node 1 and FGB elements on STS-88/Flight 2A. This procedure consisted of the SRMS grappling the respective payload, maneuvering it to a pre-install position inches above the ODS Androgynous Peripheral Attachment System (APAS) ring, commanding the SRMS into Test mode (which allows brakes-off motion of the joints), and then down-firing Primary Reaction Control System (PRCS) jets in order to effect a capture of the APAS latches. Once a successful capture had been achieved, then the AP AS was operated through its nominal retraction sequence to complete the mating sequence. While this technique can once again be used for the tail end docking portion of the ORM, the initial undocking of the orbiter and ISS vehicles with the assistance of the SRMS has yet to be attempted on orbit. The objective here is to determine the most efficient means to separate or extract the vehicles. Two techniques were analyzed in support of RTF: (1) the 'nominal' demating from the mated interface, and (2) the SRMS performing the operation (either in an active or passive fashion). In the first operation, the demating process would replicate standard undocking operations, with the exception that the SRMS is allowed to arrest the resulting motion. The second operation would be to extend the APAS ring to a ready to dock position, open the capture latches, and then detach the vehicles using the SRMS either actively or passively. In the active case, the APAS ring is extended and latched, and the SRMS is commanded to pull the two interfaces apart (assuming that the effective pull force of the SRMS can overcome the spec values of the combined latch resistance). In the passive case, the SRMS brakes are engaged and the AP AS mechanism is commanded to retract, pulling the two interfaces apart. Since the emphasis of both STS-74 and STS-88 had solely been on the installation operation, as opposed to the separation operation, two new models required development and incorporation within simulation tools designed to analyze those scenarios. These enhancements included: (1) a detailed demating dynamics model to characterize the pusher spring characteristics during undocking, and (2) contact and mechanical system modeling of the back side of the latches to represent unlatching dynamics. This paper first provides an overview of the Monte-Carlo screening analysis for the installation (both nominal and contingency), including the variation of separation distance, misalignment conditions, SRMS joint/brake parameter characteristics, and PRCS jet combinations and corresponding thrust durations. The resulting 'optimum' solution is presented based on trade studies between predicted capture success and integrated system loads. This paper then discusses the upgrades to the APAS math model associated with the new SRMS assisted undocking technique and reviews simulation results for various options investigated for either the active and passive separation of the ISS from the Orbiter.

Space Station Remote Manipulator System↗

NASA NTRS1998

Thermal Effects Modeling Developed for Smart Structures

Applying smart materials in aeropropulsion systems may improve the performance of aircraft engines through a variety of vibration, noise, and shape-control applications. To facilitate the experimental characterization of these smart structures, researchers have been focusing on developing analytical models to account for the coupled mechanical, electrical, and thermal response of these materials. One focus of current research efforts has been directed toward incorporating a comprehensive thermal analysis modeling capability. Typically, temperature affects the behavior of smart materials by three distinct mechanisms: Induction of thermal strains because of coefficient of thermal expansion mismatch 1. Pyroelectric effects on the piezoelectric elements; 2. Temperature-dependent changes in material properties; and 3. Previous analytical models only investigated the first two thermal effects mechanisms. However, since the material properties of piezoelectric materials generally vary greatly with temperature (see the graph), incorporating temperature-dependent material properties will significantly affect the structural deflections, sensory voltages, and stresses. Thus, the current analytical model captures thermal effects arising from all three mechanisms through thermopiezoelectric constitutive equations. These constitutive equations were incorporated into a layerwise laminate theory with the inherent capability to model both the active and sensory response of smart structures in thermal environments. Corresponding finite element equations were formulated and implemented for both the beam and plate elements to provide a comprehensive thermal effects modeling capability.

Lee, Ho-Jun↗

NASA NTRS2018

Validation of a CFD Model Predicting the Effect of High Level Lateral Acceleration Sloshing on the Heat Transfer and Pressure Drop in a Small-Scale Tank in Normal Gravity

A two-phase CFD model is developed to study the effects of sloshing with high level lateral acceleration on the heat transfer and pressure drop in a small scale tank. Computational results are compared to the data provided by a non-isothermal sloshing experiment without phase change conducted by T. Himeno et al. at the University of Tokyo and JAXA in 2011. The results of the current model are, also, compared to CFD predictions reported by Himeno et al. A step change in lateral acceleration was applied in the experiment. Different levels of lateral acceleration amplitude, varying between 0G and 0.5G, were considered. CFD results for interface movement and tank pressure are presented and compared in this paper to the experimental data for the case in which the value of lateral acceleration was set to 0.5G. The effects of initial and boundary conditions and turbulence modeling approach on the tank pressure change during sloshing are discussed in detail. The effect of conjugate heat transfer in the tank wall is also studied to show its important role in determining the tank pressure evolution. The results of the Reynolds Averaged Navier Stokes (RANS) models are compared to the results of the Large Eddy Simulation model (LES) to underscore the importance of correctly capturing the effects of turbulence for high fidelity predictions.

multiphase flow↗

NASA NTRS2018

Validation of A CFD Model Predicting the Effect of High Level Lateral Acceleration Sloshing on the Heat Transfer and Pressure Drop in A Small-Scale Tank in Normal Gravity

A two-phase CFD model is developed to study the effects of sloshing with high level lateral acceleration on the heat transfer and pressure drop in a small scale tank. Computational results are compared to the data provided by a non-isothermal sloshing experiment without phase change conducted by T. Himeno et al. at the University of Tokyo and JAXA in 2011 [1]. The results of the current model are, also, compared to CFD predictions reported by Himeno et al. [2]. A step change in lateral acceleration was applied in the experiment. Different levels of lateral acceleration amplitude, varying between 0G and 0.5G, were considered. CFD results for interface movement and tank pressure are presented and compared in this paper to the experimental data for the case in which the value of lateral acceleration was set to 0.5G. The effects of initial and boundary conditions and turbulence modeling approach on the tank pressure change during sloshing are discussed in detail. The effect of conjugate heat transfer in the tank wall is also studied to show its important role in determining the tank pressure evolution. The results of the Reynolds Averaged Navier Stokes (RANS) models are compared to the results of the Large Eddy Simulation model (LES) to underscore the importance of correctly capturing the effects of turbulence for high fidelity predictions.

multiphase flow↗

NASA NTRS2014

Liquefied Bleed for Stability and Efficiency of High Speed Inlets

A mission analysis code was developed to perform a trade study on the effectiveness of liquefying bleed for the inlet of the first stage of a TSTO vehicle. By liquefying bleed, the vehicle weight (TOGW) could be reduced by 7 to 23%. Numerous simplifying assumptions were made and lessons were learned. Increased accuracy in future analyses can be achieved by: Including a higher fidelity model to capture the effect of rescaling (variable vehicle TOGW). Refining specific thrust and impulse models ( T m a and Isp) to preserve fuel-to-air ratio. Implementing LH2 for T m a and Isp. Correlating baseline design to other mission analyses and correcting vehicle design elements. Implementing angle-of-attack effects on inlet characteristics. Refining aerodynamic performance (to improve L/D ratio at higher Mach numbers). Examining the benefit with partial cooling or densification of the bleed air stream. Incorporating higher fidelity weight estimates for the liquefied bleed system (heat exchange and liquid storage versus bleed duct weights) could be added when more fully developed. Adding trim drag or 6-degree-of-freedom trajectory analysis for higher fidelity. Investigating vehicle optimization for each of the bleed configurations.

Saunders, J. David↗