Search NASA⌕ Search

SEARCH · Search NASA

Results for “CENTER OF GRAVITY - POSITION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

A New Global Regression Analysis Method for the Prediction of Wind Tunnel Model Weight Corrections

A new global regression analysis method is discussed that predicts wind tunnel model weight corrections for strain-gage balance loads during a wind tunnel test. The method determines corrections by combining "wind-on" model attitude measurements with least squares estimates of the model weight and center of gravity coordinates that are obtained from "wind-off" data points. The method treats the least squares fit of the model weight separate from the fit of the center of gravity coordinates. Therefore, it performs two fits of "wind- off" data points and uses the least squares estimator of the model weight as an input for the fit of the center of gravity coordinates. Explicit equations for the least squares estimators of the weight and center of gravity coordinates are derived that simplify the implementation of the method in the data system software of a wind tunnel. In addition, recommendations for sets of "wind-off" data points are made that take typical model support system constraints into account. Explicit equations of the confidence intervals on the model weight and center of gravity coordinates and two different error analyses of the model weight prediction are also discussed in the appendices of the paper.

strain-gage balance↗
NASA NTRS1978

Prelaunch testing of the GEOS-3 laser reflector array

The prelaunch testing performed on the Geos-3 laser reflector array before launch was used to determine the lidar cross section of the array and the distance of the center of gravity of the satellite from the center of gravity of reflected laser pulses as a function of incidence angle. Experimental data are compared to computed results.

Minott, P. O.↗
NASA NTRS1983

Weight and Balance for the Airmass Incorporated Sunburst Model C Ultralight

The results of the weight and balance determination done for an ultralight aircraft are presented. The weight and balance determination encompassed finding weight and center of gravity of each component, determining the center of gravity of the ultralight in an X, Y, Z reference plane, and calculating the mass moments and products of inertia. The relations were calculated for various pilot weights and fuel loadings. The fuel varied from empty to five gallons (31.05 lbs), and the pilots ranged from 90 to 260 pounds. The weighings of components total 277.48 lbs (no pilot and no fuel).

Source record↗
NASA NTRS2014

Lunar Reconnaissance Orbiter Orbit Determination Accuracy Analysis

LRO definitive and predictive accuracy requirements were easily met in the nominal mission orbit, using the LP150Q lunar gravity model. center dot Accuracy of the LP150Q model is poorer in the extended mission elliptical orbit. center dot Later lunar gravity models, in particular GSFC-GRAIL-270, improve OD accuracy in the extended mission. center dot Implementation of a constrained plane when the orbit is within 45 degrees of the Earth-Moon line improves cross-track accuracy. center dot Prediction accuracy is still challenged during full-Sun periods due to coarse spacecraft area modeling - Implementation of a multi-plate area model with definitive attitude input can eliminate prediction violations. - The FDF is evaluating using analytic and predicted attitude modeling to improve full-Sun prediction accuracy. center dot Comparison of FDF ephemeris file to high-precision ephemeris files provides gross confirmation that overlap compares properly assess orbit accuracy.

Gravitation↗
NASA NTRS1965

Spin-Entry Characteristics of a Large Supersonic Bomber as Determined by Dynamic Model Tests

An investigation has been conducted in the Langley spin tunnel and at a catapult launch facility of a 1/60-scale dynamic model to determine the spin-entry characteristics of a large supersonic bomber. Catapult tests indicated that spin-entry motions were obtainable for a center-of-gravity location of 0.21 mean aerodynamic chord but were not obtainable at a center-of-gravity location of 0.25 mean aerodynamic chord. Deflected ailerons were effective in promoting or preventing the spin- entry motion and this effect was qualitatively the same as it was for the fully developed spin. Varying the configuration had little significant effect on the spin-entry characteristics. Brief tests conducted with the model in the Langley spin tunnel indicated that fully developed spins were obtainable at the forward center-of-gravity location and that spins were highly unlikely at the rearward center-of-location.

Bowman, James S.↗
NASA NTRS2000

Emergency flight control system using one engine and fuel transfer

A system for emergency aircraft control uses at least one engine and lateral fuel transfer that allows a pilot to regain control over an aircraft under emergency conditions. Where aircraft propulsion is available only through engines on one side of the aircraft, lateral fuel transfer provides means by which the center of gravity of the aircraft can be moved over to the wing associated with the operating engine, thus inducing a moment that balances the moment from the remaining engine, allowing the pilot to regain control over the aircraft. By implementing the present invention in flight control programming associated with a flight control computer (FCC), control of the aircraft under emergency conditions can be linked to the yoke or autopilot knob of the aircraft. Additionally, the center of gravity of the aircraft can be shifted in order to effect maneuvers and turns by spacing such center of gravity either closer to or farther away from the propelling engine or engines. In an alternative embodiment, aircraft having a third engine associated with the tail section or otherwise are accommodated and implemented by the present invention by appropriately shifting the center of gravity of the aircraft. Alternatively, where a four-engine aircraft has suffered loss of engine control on one side of the plane, the lateral fuel transfer may deliver the center of gravity closer to the two remaining engines. Differential thrust between the two can then control the pitch and roll of the aircraft in conjunction with lateral fuel transfer.

Burcham, Jr., Frank W.↗
NASA NTRS1997

Subsonic Dynamics of Stardust Sample Return Capsule

Subsonic dynamic stability tests performed in the NASA Langley 20-Foot Vertical Spin-Tunnel on a 0.238 scale model of the Stardust Sample Return Capsule are discussed. The tests reveal that the blunted 60 degree half-angle cone capsule is dynamically unstable at low subsonic conditions due to the aft location of the center-of-gravity (0.351 body diameters back from the nose). The divergent behavior of the capsule continued when the center-of-gravity was moved to 0.337 and 0.313 body diameters back from the nose. When the center-of-gravity was moved further forward to 0.290 body diameters back from the nose, the vehicle established itself in a limit cycle with amplitude around 10 degrees. Two afterbody modifications were examined which proved unsuccessful in alleviating the instability of the original design. Finally, the addition of different sized parachutes was examined as a means to stabilize the vehicle. The parachute tests indicate that a parachute with equivalent full scale drag area of at least 2.24 ft. is necessary to assure large perturbations are damped.

Mitcheltree, Robert A.↗
NASA NTRS1972

NERVA mass properties computer methodology

The computer codes are presented that were used for the weight, center of gravity, and mass moment of inertia calculations and documentation for the NERVA. The two programs, E15301 and 12001B, are the basic tools used for weights work on the NERVA program. Used in conjunction with one another, they allow for rapid weights estimates for new concepts or changes while allowing for orderly documentation, which is a necessity in any effective weights effort. Program E15301 requires that each component be resolved into a collection of standard shapes. Separate subroutines then process geometric and material density data for each entry. The master program the performs all calculations necessary to combine these results into a total weight, center of gravity, and moment of inertia for the component. Program 12001B accepts previously calculated weight and center of gravity data for individual components. The program sums weights and calculates center of gravities and moments of inertia for systems of up to four levels of assemblies. The output identifies the engine parts in a format usable directly in a formal report.

Hall, I. K.↗
NASA NTRS1986

The predicted effect of aerodynamic detuning on coupled bending-torsion unstalled supersonic flutter

A mathematical model is developed to predict the enhanced coupled bending-torsion unstalled supersonic flutter stability due to alternate circumferential spacing aerodynamic detuning of a turbomachine rotor. The translational and torsional unsteady aerodynamic coefficients are developed in terms of influence coefficients, with the coupled bending-torsion stability analysis developed by considering the coupled equations of motion together with the unsteady aerodynamic loading. The effect of this aerodynamic detuning on coupled bending-torsion unstalled supersonic flutter as well as the verification of the modeling are then demonstrated by considering an unstable 12 bladed rotor, with Verdon's uniformly spaced Cascade B flow geometry as a baseline. However, with the elastic axis and center of gravity at 60 percent of the chord, this type of aerodynamic detuning has a minimal effect on stability. For both uniform and nonuniform circumferentially space rotors, a single degree of freedom torsion mode analysis was shown to be appropriate for values of the bending-torsion natural frequency ratio lower than 0.6 and higher 1.2. When the elastic axis and center of gravity are not coincident, the effect of detuning on cascade stability was found to be very sensitive to the location of the center of gravity with respect to the elastic axis. In addition, it was determined that when the center of gravity was forward of an elastic axis located at midchord, a single degree of freedom torsion model did not accurately predict cascade stability.

Hoyniak, D.↗
NASA NTRS1986

The effect of circumferential aerodynamic detuning on coupled bending-torsion unstalled supersonic flutter

A mathematical model developed to predict the enhanced coupled bending-torsion unstalled supersonic flutter stability due to alternate circumferential spacing aerodynamic detuning of a turbomachine rotor. The translational and torsional unsteady aerodynamic coefficients are developed in terms of influence coefficients, with the coupled bending-torsion stability analysis developed by considering the coupled equations of this aerodynamic detuning on coupled bending-torsion unstalled supersonic flutter as well as the verification of the modeling are then demonstrated by considering an unstable 12 bladed rotor, with Verdon's uniformly spaced Cascade B flow geometry as a baseline. However, with the elastic axis and center of gravity at 60 percent of the chord, this type of aerodynamic detuning has a minimal effect on stability. For both uniform and nonuniform circumferentially space rotors, a single degree of freedom torsion mode analysis was shown to be appropriate for values of the bending-torsion natural frequency ratio lower than 0.6 and higher 1.2. When the elastic axis and center of gravity are not coincident, the effect of detuning on cascade stability was found to be very sensitive to the location of the center of gravity with respect to the elastic axis. In addition, it was determined that when the center of gravity was forward of an elastic axis located at midchord, a single degree of freedom torsion model did not accurately predict cascade stability.

Hoyniak, D.↗
NASA NTRS1949

Preliminary Results of a Free-Flight Investigation of the Static Stability and Aileron Control Characteristics of 1/6 Scale Models of the Bell MX-776

An investigation of the static longitudinal stability, static directional stability, and aileron control characteristics at transonic and supersonic speeds is being made of 1/6 scale rocket-propelled model of the Bell MX-776. A stability investigation has been made of two symmetrical models with controls undeflected and centers of gravity one-half and one-body diameter, respectively, ahead of the equivalent design center-of-gravity location of the full-scale version. Both models developed large normal-force coefficients in both the subsonic and supersonic ranges which indicated longitudinal instability at low angles of attack. The side-force coefficients were small for both models and indicated that the models were directionally stable. A possible tendency toward dynamic directional instability in the transonic region was indicated by short-period oscillations of the side forces. The results showed a partial-span inboard aileron to be ineffective or to cause negative control in the the transonic region when deflected approximately 5 deg but not when deflected 10 deg. An investigation of drag showed it to increase with a rearward movement of the center of gravity. This indicates an increase in the trim angle of attack as could be caused by a decrease in static stability.

Michal, David H.↗
NASA NTRS1948

Theoretical motions of hydrofoil systems

Results are presented of an investigation that has been undertaken to develop theoretical methods of treating the motions of hydrofoil systems and to determine some of the important parameters. Variations of parameters include three distributions of area between the hydrofoils, two rates of change of downwash angle with angle of attack, three depths of immersion, two dihedral angles, two rates of change of lift with immersion, three longitudinal hydrofoil spacings, two radii of gyration in pitching, and various horizontal and vertical locations of the center of gravity. Graphs are presented to show locations of the center of gravity for stable motion, values of the stability roots, and motions following the sudden application of a vertical force or a pitching moment to the hydrofoil system for numerous sets of values of the parameters.

Imlay, Frederick H↗
NASA NTRS1983

The Marshall Space Flight Center KC-135 zero gravity test program for FY 1982

During FY-82, researchers and experimenters from Marshall Space Flight Center (MSFC) conducted 11 separate investigations during 26.3 hr of testing aboard the KC-135 zero-gravity aircraft, based at Ellington Air force Base, Texas. Although this represented fewer hours than initially projected, all experiment and test objectives were met or exceeded. This Technical Memorandum compiles all results achieved by MSFC users during FY-82, a year considered to be highly productive.

Shurney, R. E.↗
NASA NTRS1950

Static Longitudinal Stability of a Tandem-Coupled Bomber-Fighter Airplane Configuration Proposed by All American Airways, Inc.

At the request of the Air Materiel Command an investigation was made in the Langley free-flight tunnel to determine the static longitudinal stability and control characteristics of models coupled together in a tandem configuration proposed by All American Airways, Inc. Force tests were made using 1/20-scale models of B-29 end F-80 airplanes to determine the effects of coupling the fighter to the tail of the bomber. The results of the investigation showed that for the bomber alone the aerodynamic center was 0.21 mean aerodynamic chord behind the center of gravity (stable) but that for the tandem configuration the aerodynamic center was 0.09 mean aerodynamic chord forward of the center of gravity, of the combination (unstable). The elevator effectiveness of the bomber was reduced approximately 50 percent by addition of the fighter. Some recent flight tests made in the free-flight tunnel with models simulating the proposed configuration indicate that the reduction in stability may be minimized by incorporating a hinged coupling permitting freedom in pitch.

Hewes, Donald E.↗
NASA NTRSDate not supplied

Weight and Balance Considerations for Electrified Aircraft Propulsion Applied to the Parallel Electric-Gas Architecture with Synergistic Utilization Scheme (PEGASUS) Concept

The focus of this research was to understand the impact of batteries and electric motors on the weight and balance of the Parallel Electric-Gas Architecture with Synergistic Utilization Scheme (PEGASUS) concept. Because electrified aircraft propulsion components can comprise a large part of an aircraft’s weight, their integration has a significant impact on the center of gravity location and the related stability characteristics of the aircraft. We developed an analysis framework that enabled estimating the weight and volume of electrified aircraft components, their contribution to the center of gravity location, and the stability and performance of the aircraft. Trades were performed on battery placement, wing attachment point, and electric motor power to determine their impact on figures of merit such as maximum takeoff weight and block fuel. We identified batteries, and to a lesser extent electric motors, as having a large impact on aircraft center of gravity and the required horizontal tail size for longitudinal static stability. Placing electric component weight as far forward as possible resulted in reductions in the horizontal tail size required to maintain static stability. Configurations output from this framework were also evaluated using a six-degree-of-freedom simulation to quantify dynamic stability characteristics. Although shifting weight forward reduced horizontal tail size, it negatively impacted dynamic stability. This study confirms that mass property modeling and dynamic simulation, which are usually limited in conceptual design, are important for electrified aircraft concepts.

electrified aircraft propulsion↗
NASA NTRS1950

Static Longitudinal Stability of a Tandem-Coupled Bomber-Fighter Airplane Configuration Similar to One Proposed by Douglas Aircraft Company, Inc.

At the request of the Air Materiel Command, an investigation was made in the Langley free-flight tunnel to determine the longitudinal stability and control characteristics of models coupled together in a tandem configuration for aerial refueling similar to one proposed by the Douglas Aircraft Company, Inc. Static force tests were made with 1/20-scale models of the B-29 and F-80 airplanes to determine the effects of rigidly coupling the airplanes together. The Douglas configuration differs from the rigid configuration tested in that it provides for some freedom in pitch and vertical displacement. The force tests showed that, for the bomber alone, the aerodynamic center was 0.21 mean aerodynamic chord behind the center of gravity (stable) but that for the tandem configuration with rigid coupling the aerodynamic center was 0.28 mean aerodynamic chord forward of the center of gravity of the combination (unstable). This reduction in stability was caused by the downwash of the bomber on the fighter. The pitching moment produced by elevator deflection of the bomber was reduced approximately 50 percent by addition of the fighter. Some recent flight tests made in the free-flight tunnel on models in a similar tandem configuration indicated that, with a hinged coupling permitting freedom in pitch, the stability of the combination was better than that obtained with a rigid coupling and was about the same as that for the bomber alone.

Hewes, Donald E.↗
NASA NTRS1981

Exploratory flight test of advanced piloted spacecraft - Circa 1963

The NASA early experimental program for parawing and lifting body spacecraft recovery concepts is discussed. Simple hand drawings, in-house construction, and crude drop tests were used in lieu of a thorough stress analysis. The parawing (parasev) was controlled by manually shifting the center of gravity with respect to the center of pressure; the craft would take off while being towed at 40 KIAS. The M-2 lifting body was originally constructed with a 3/32 in. mahogany skin by a glider manufacturer and employed general aviation aircraft nose and main wheel assemblies. A minimum altitude of 200 ft was found acceptable for release of the parasev, allowing the pilot time to adjust for transients incurred at the tow release. A small landing assist rocket was furnished for the M-2/F-2 and X-24A lifting bodies to enhance stability, and landings at a maximum lift/drag ratio of 2.8 were successfully completed. The data gained were eventually applied in the development of the Shuttle.

Thompson, M. O.↗
NASA NTRS1991

An aeroelastic analysis with a generalized dynamic wake

An aeroelastic model with generalized dynamic wake is developed for application in the integration of aerodynamic, dynamic, and structural optimization of a rotor blade. The investigation is carried out with special attention to efficiency and accuracy of aeroelastic modeling. Each blade is assumed to be an elastic beam undergoing flap bending, lead-lag bending, elastic twist and axial deflections. The nonuniform blade is discretized into finite beam elements, each of which consists of twelve degrees of freedom. Such important blade design variables as pretwist, and chordwise offsets of the blade center of gravity and of the aerodynamic center from the elastic axis have been included in the analysis. Aerodynamic loads are computed from unsteady blade element theory where the rotor three-dimensional unsteady wake is modeled using a generalized dynamic wake theory. The noncirculatory loads based on unsteady thin airfoil theory are also included.

He, Cheng J.↗