Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONICAL NOZZLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Noise suppression due to annulus shaping of an inverted-velocity-profile coaxial nozzle

Previous studies have shown that an inverted-velocity-profile coaxial nozzle for use with supersonic cruise aircraft produces less jet noise than an equivalent conical nozzle. Furthermore, decreasing the annulus height (increasing radius ratio with constant flow) results in further noise reduction benefits. In the present model-scale study, the annulus shape, that is, height, was varied by an eccentric mounting of the annular nozzle with respect to a conical core nozzle. Acoustic measurements were made in the flyover plane below the narrowest portion of the annulus and at 90 deg and 180 deg from this point. The model-scale spectra are scaled up to engine size (1.07 m diameter) and the perceived noise levels for the eccentric and baseline concentric inverted-velocity-profile coaxial nozzles are compared over a range of operating conditions. The implications of the acoustic benefits derived with the eccentric nozzle to practical applications are discussed.

Goodykoontz, J.↗
NASA NTRS2004

A Method for Estimating Noise from Full-Scale Distributed Exhaust Nozzles

A method to estimate the full-scale noise suppression from a scale model distributed exhaust nozzle (DEN) is presented. For a conventional scale model exhaust nozzle, Strouhal number scaling using a scale factor related to the nozzle exit area is typically applied that shifts model scale frequency in proportion to the geometric scale factor. However, model scale DEN designs have two inherent length scales. One is associated with the mini-nozzles, whose size do not change in going from model scale to full scale. The other is associated with the overall nozzle exit area which is much smaller than full size. Consequently, lower frequency energy that is generated by the coalesced jet plume should scale to lower frequency, but higher frequency energy generated by individual mini-jets does not shift frequency. In addition, jet-jet acoustic shielding by the array of mini-nozzles is a significant noise reduction effect that may change with DEN model size. A technique has been developed to scale laboratory model spectral data based on the premise that high and low frequency content must be treated differently during the scaling process. The model-scale distributed exhaust spectra are divided into low and high frequency regions that are then adjusted to full scale separately based on different physics-based scaling laws. The regions are then recombined to create an estimate of the full-scale acoustic spectra. These spectra can then be converted to perceived noise levels (PNL). The paper presents the details of this methodology and provides an example of the estimated noise suppression by a distributed exhaust nozzle compared to a round conic nozzle.

Kinzie, Kevin W.↗
NASA NTRS1976

Analytical modeling of under-the-wing externally blown flap powered-lift noise

The sound field produced by the interaction of a subsonic jet with a large-scale model of the under the wing externally blown flap in an approach attitude was analyzed. The analysis was performed to obtain a better understanding of the dominant noise sources and the mechanisms governing the peak sound pressure level frequencies of the broadband spectra. An analytical expression is derived which incorporates two available theories and experimental data; the expression predicts the sound field along a circular arc of approximately 120 deg measured from the upstream jet axis in the fly-over plane. The analysis compares favorably with test results obtained from two large-scale models, one using cold air from a conical nozzle and the other using hot gas from a TF-34 turbofan engine having a conical exhaust nozzle with a 12 lobe internal forced mixer. The frequency at which the peak sound pressure level occurs appears to be governed by a phenomenon which produces periodic formation and shedding of large-scale turbulence structures from the nozzle lip.

Mckinzie, D. J., Jr.↗
NASA NTRS1987

Aeroacoustics of supersonic jet flows from contoured and solid/porous conical plug-nozzles

The results of an experimental study of the acoustic far-field, the shock associated noise, and the nature of the repetitive shock structure of supersonic jet flows issuing from plug-nozzles having externally-expanded plugs with pointed termination operated at a range of supercritical pressure ratios Xi approaching 2 to 4.5 are reported. The plug of one of these plug-nozzles was contoured. The other plug-nozzles had short conical plugs with either a solid surface or a combination of solid/porous surface of different porosities. The contoured and the uncontoured plug-nozzles had the same throat area and the same annulus-radius ratio K = R sub p/R sub N = 0.43. As the result of modifications of the shock structure, the acoustic performance of improperly expanded jet flows of an externally-expanded short uncontoured plug of an appropriate geometry with suitably perforated plug and a pointed termination, is shown to approach the acoustic performance of a shock-free supersonic jet issuing from an equivalent externally-expanded contoured plug-nozzle.

Dosanjh, Darshan S.↗
NASA NTRS1976

Blast wave in a nozzle for propulsive applications

The reported investigation has been conducted in connection with studies concerning the development of a propulsion system based on the use of a detonating fluid propellant. Measurements have been made of the pressure and shock wave velocity in a conical nozzle at various ambient pressures and at an ambient temperature of 25 C. In the experiments a small amount of explosive was placed at the end wall of a conical aluminum nozzle and detonated by a microdetonator inside the nozzle. Differences regarding the characteristics of conventional chemical propulsion and detonation propulsion are illustrated with the aid of a graph. One- and two-dimensional numerical flow calculations were performed and compared with the experimental data.

Varsi, G.↗
NASA NTRS1984

Free-jet acoustic investigation of high-radius-ratio coannular plug nozzles

The experimental and analytical results of a scale model simulated flight acoustic exploratory investigation of high radius ratio coannular plug nozzles with inverted velocity and temperature profiles are summarized. Six coannular plug nozzle configurations and a baseline convergent conical nozzle were tested for simulated flight acoustic evaluation. The nozzles were tested over a range of test conditions that are typical of a Variable Cycle Engine for application to advanced high speed aircraft. It was found that in simulate flight, the high radius ratio coannular plug nozzles maintain their jet noise and shock noise reduction features previously observed in static testing. The presence of nozzle bypass struts will not significantly affect the acousticn noise reduction features of a General Electric type nozzle design. A unique coannular plug nozzle flight acoustic spectral prediction method was identified and found to predict the measured results quite well. Special laser velocimeter and acoustic measurements were performed which have given new insights into the jet and shock noise reduction mechanisms of coannular plug nozzles with regard to identifying further benificial research efforts.

Knott, P. R.↗
NASA NTRS1990

High-speed quiet tunnels

The adverse effect of wind-tunnel noise on boundary-layer transition is considered, and the development of Pilot Quiet Tunnels exhibiting low noise levels in upstream regions of the test rhombus to high values of the stream unit Reynolds number is covered. Advances in quiet nozzle and tunnel designs are discussed, including a new Mach-8 nozzle and modifications to an existing conical nozzle in one of the helium tunnels at NASA Langley. Attention is focused on the final engineering design of a large-scale high-speed low-disturbance tunnel expected to accommodate nozzles of various lengths with Mach numbers ranging from 2 to 6.

Beckwith, Ivan E.↗
NASA NTRS1960

Experimental Performance of Area Ratio 200, 25 and 8 Nozzles on JP-4 Fuel and Liquid Oxygen Rocket Engine

The performance of an area ratio 200 bell-shaped nozzle, an area ratio 25 bell-shaped nozzle, and an area ratio 8 conic nozzle on a JP-4 fuel and liquid-oxygen rocket engine has been determined. Tests were conducted using a nominal 4000-pound-thrust rocket in the Lewis 10- by 10-foot supersonic tunnel, which provided the altitude environment needed for fully expanded nozzle flow. The area ratio 200 nozzle had a vacuum thrust coefficient of 1.96, compared with 1.82 and 1.70 for the area ratio 25 and 8 nozzles, respectively. These values are approximately equal to those for theoretical frozen expansion. The measured value of vacuum specific impulse for the area ratio 200 nozzle was 317 seconds for a combustion-chamber characteristic velocity of 5200 feet per second. The vacuum-specific-impulse increase for the area-ratio increase from 8 to 200 was 46 seconds.

Lovell, J. Calvin↗
NASA NTRS1993

Experimentation in the low-density plume of a simulated electrothermal thruster for computer code validation

Pressures and flow angles are measured in the plume of a 20 deg half-angle, conical nozzle in vacuum with Pitot tubes and conical probes. The area of measurement in the plume ranges from the nozzle exit plane to 480 mm axially downstream and from the plume centerline to 60 mm radially. The nozzle has an exit-to-throat area ratio of 100:1 and a throat diameter of 3.2 mm. The nozzle flow exhausts to a vacuum of order 10(exp -2) Pa to simulate a resistojet (an electrothermal rocket of less than 1 N of thrust) operating in space. Experimental data are given for flows of nitrogen at 55 and 68 mg/s, stagnation temperatures between 695 and 921 K, and stagnation pressures ranging from 5600 to 7100 Pa. Data are also given for argon at a rate of 68 mg/s, a stagnation temperature of 648 K, and stagnation pressures of 4500, 4750, and 4770 Pa. Measurements in the nitrogen plume are compared with computational results from a direct-simulation Monte Carlo method.

Meissner, Dana L.↗
NASA NTRS1990

Efficient Monte Carlo simulation of rarefied flow in a small nozzle

The flow of carbon dioxide through a small conical nozzle is computed using two different numerical approaches. The first of these is the direct simulation Monte Carlo method in which the physical phenomena are modeled at the molecular level. The second technique solves the Navier-Stokes equations of fluid flow. The purpose of the paper is to compare the solutions generated by these two methods for the conditions prevailing in a small, low density nozzle. The comparison between the two sets of solutions reveals only small differences. However, the flow properties in the thick viscous layer close to the nozzle at the exit plane show important deviations which have implications for the subsequent determination of the plume backflow.

Boyd, Iain D.↗
NASA NTRS1991

The spatial characteristics of the B helical mode for a choked axisymmetric nozzle

An acoustic near-field study was performed for an axisymmetric conical nozzle operated at a fully expanded Mach number of 1.3. The acoustic measurements were performed in the nozzle exit plane using multiple sensors arranged around the periphery of the nozzle. The acquired data were simultaneously digitized. The acoustic spatial characteristics, describing the large scale structure associated with the preferred shear layer instability mode, were determined for the dominant B screech mode. The nozzle was fitted with a lip thickening device to determine the effect of this geometric variable on the spatial structure of the jet. For the thin-lipped configuration, the flapping structure of the B screech mode was found to precess in a time-dependent manner about the jet axis. An increasing of the nozzle exit lip thickness altered the spatial characteristics of this mode from a flapping to a time-dependent flapping or spinning. Using the auto-bicoherence spectrum, frequency dependencies were found to exist in the acoustic data of the thick-lipped configuration. These dependencies may be related to the nonlinearity of the jet and/or the time-dependent nature of the B mode spatial structure.

Ponton, Michael K.↗
NASA NTRS2008

Visualization of Flowfield Modification by RCS Jets on a Capsule Entry Vehicle

Nitric oxide planar laser-induced fluorescence (NO PLIF) has been used to visualize the flow on the aft-body of an entry capsule having an activated RCS jet in NASA Langley Research Center's 31-Inch Mach 10 wind tunnel facility. A capsule shape representative of the Apollo command module was tested. These tests were performed to demonstrate the ability of the PLIF method to visualize RCS jet flow while providing some preliminary input to NASA's Orion Vehicle design team. Two different RCS nozzle designs - conical and contoured - were tested. The conical and contoured nozzles had area ratios of 13.4 and 22.5 respectively. The conical nozzle had a half-angle of 10 . Low- and high-Reynolds number cases were investigated by changing the tunnel stagnation pressure from 350 psi to 1300 psi, resulting in freestream Reynolds numbers of 0.56 and 1.8 million per foot respectively. For both of these cases, three different jet plenum pressures were tested (nominally 56, 250 and 500 psi). A single angle-of-attack was investigated (24 degrees). NO PLIF uses an ultraviolet laser sheet to interrogate a slice in the flow containing seeded NO; this UV light excites fluorescence from the NO molecules which is detected by a high-speed digital camera. The system has spatial resolution of about 200 microns (2 pixel blurring) and has flow-stopping time resolution (approximately 1 microsecond). NO was seeded into the flow two different ways. First, the RCS jet fluid was seeded with approximately 1-5% NO, with the balance N2. This allowed observation of the shape, structure and trajectory of the RCS jets. Visualizations of both laminar and turbulent flow jet features were obtained. Visualizations were obtained with the tunnel operating at Mach 10 and also with the test section held at a constant pressure similar to the aftbody static pressure (0.04 psi) obtained during tunnel runs. These two conditions are called "tunnel on" and "tunnel off" respectively. Second, the forebody flow was seeded with a very low flowrate (<100 standard cubic centimeters per minute) of pure NO. This trace gas was entrained into and allowed visualization of the shear layer forming between the expansion fan on the shoulder of the model and the recirculating separated flow in the wake of the model. This shear layer was observed to be laminar in the absence of the RCS jet operation and turbulent above a certain RCS jet flowrate. Furthermore, the operation of the RCS jet is seen to push the shear layer out away from the model, with a higher jet pressures resulting in larger deflections. Figures show some data from this test, partially processed. In the final paper, these images will be processed and rendered on a three dimensional visualization of the test hardware for clearer visualization and interpretation of the flowfields.

Danehy, P. M.↗
NASA NTRS1973

Pressures and temperatures on the lower surfaces of an externally blown flap system during full-scale ground tests

Full-scale ground tests of an externally blown flap system were made using the wing of an F-111B airplane and a CF700 engine. Pressure and temperature distributions were determined on the undersurface of the wing, vane, and flap for two engine exhaust nozzles (conical and daisy) at several engine power levels and engine/wing positions. The test were made with no airflow over the wing. The wing sweep angle was fixed at e6 deg; and the angle of incidence between the engine and the wing was fixed at 3 deg; and the flap was in the retracted, deflected 35 deg, and deflected 60 deg positions. The pressure load obtained by integrating the local pressures on the undersurface of the flap, F sub p was approximately three times greater at the 60 deg flap position than at the 35 deg flap position. At the 60 deg flap position, F sub p was between 40 percent and 55 percent of the engine thrust over the measured range of thrust. More than 90 percent of F sub p was contained within plus or minus 20 percent of the flap span centered around the engine exhaust centerline with both nozzle configurations. Maximum temperatures recorded on the flaps were 218 C (424 F) and 180 C (356 F) for the conical and daisy nozzles, repectively,

Hughes, D. L.↗
NASA NTRS1981

Jet noise results from static, wind tunnel, and flight tests of conical and mechanical suppressor nozzles

Results of jet noise suppression tests conducted on a Rolls-Royce Viper 601 turbojet engine are reported. Seven exhaust nozzle configurations are tested, including two conical nozzles, two suppressor mixers, and three treated ejector configurations with different ejector inlets. Tests are conducted at the NASA Ames outdoor static test facility and the 40- by 80-ft wind tunnel facility at minimum tunnel flow velocity and normal flow velocities of 230 and 290 ft/sec. Near-field multiple sideline noise levels are projected to the far fields to compare far-field fixed microphone outdoor static noise levels, and wind tunnel near-field noise data are projected to the far field and flight distances to compare with noise levels recorded from an Hs-125 aircraft. Near-field outdoor noise data duplicate the far-field data recorded from fixed microphones within 2 PNdB, and the Douglas mechanical jet noise suppressor/treated ejector exhaust system achieves a noise reduction of 12 EPNdB relative to a conic reference nozzle at equal thrust in flight.

Mckinnon, R. A.↗
NASA NTRS1985

Aeroacoustics of contoured and solid/porous conical plug-nozzle supersonic jet flows

The acoustic far field, the shock-associated noise and characteristics of the repetitive shock structure of supersonic jet flows issuing from a contoured plug-nozzle and uncontoured plug-nozzle having a short conical plug of either a solid or a combination of solid/porous surface with pointed termination operated at a range of supercritical pressure are reported. The contoured and the uncontoured plug-nozzles had the same throat area and the same annular-radius ratio.

Dosanjh, D. S.↗