Results for “Carbon/Carbon composites” — Page 5

NASA NTRS2012

Active Oxidation of a UHTC-Based CMC

The active oxidation of ceramic matrix composites (CMC) is a severe problem that must be avoided for multi-use hypersonic vehicles. Much work has been performed studying the active oxidation of silicon-based CMCs such as C/SiC and SiC-coated carbon/carbon (C/C). Ultra high temperature ceramics (UTHC) have been proposed as a possible material solution for high-temperature applications on hypersonic vehicles. However, little work has been performed studying the active oxidation of UHTCs. The intent of this paper is to present test data indicating an active oxidation process for a UHTC-based CMC similar to the active oxidation observed with Si-based CMCs. A UHTC-based CMC was tested in the HyMETS arc-jet facility (or plasma wind tunnel, PWT) at NASA Langley Research Center, Hampton, VA. The coupon was tested at a nominal surface temperature of 3000 F (1650 C), with a stagnation pressure of 0.026 atm. A sudden and large increase in surface temperature was noticed with negligible increase in the heat flux, indicative of the onset of active oxidation. It is shown that the surface conditions, both temperature and pressure, fall within the region for a passive to active transition (PAT) of the oxidation.

Glass, David E.↗

NASA NTRS2004

As-Fabricated Reinforced Carbon/Carbon Characterized

Reinforced carbon/carbon (RCC) is a critical material for the space shuttle orbiter. It is used on the wing leading edge and the nose cap, where maximum temperatures are reached on reentry. The existing leading-edge system is a single-plate RCC composite construction with a wall thickness of approximately 1/4 in., making it a prime reliant protection scheme for vehicle operation.

Jacobson, Nathan S.↗

NASA NTRS2011

Lightweight, Ultra-High-Temperature, CMC-Lined Carbon/Carbon Structures

Carbon/carbon (C/C) is an established engineering material used extensively in aerospace. The beneficial properties of C/C include high strength, low density, and toughness. Its shortcoming is its limited usability at temperatures higher than the oxidation temperature of carbon . approximately 400 C. Ceramic matrix composites (CMCs) are used instead, but carry a weight penalty. Combining a thin laminate of CMC to a bulk structure of C/C retains all of the benefits of C/C with the high temperature oxidizing environment usability of CMCs. Ultramet demonstrated the feasibility of combining the light weight of C/C composites with the oxidation resistance of zirconium carbide (ZrC) and zirconium- silicon carbide (Zr-Si-C) CMCs in a unique system composed of a C/C primary structure with an integral CMC liner with temperature capability up to 4,200 F (.2,315 C). The system effectively bridged the gap in weight and performance between coated C/C and bulk CMCs. Fabrication was demonstrated through an innovative variant of Ultramet fs rapid, pressureless melt infiltration processing technology. The fully developed material system has strength that is comparable with that of C/C, lower density than Cf/SiC, and ultra-high-temperature oxidation stability. Application of the reinforced ceramic casing to a predominantly C/C structure creates a highly innovative material with the potential to achieve the long-sought goal of long-term, cyclic high-temperature use of C/C in an oxidizing environment. The C/C substructure provided most of the mechanical integrity, and the CMC strengths achieved appeared to be sufficient to allow the CMC to perform its primary function of protecting the C/C. Nozzle extension components were fabricated and successfully hot-fire tested. Test results showed good thermochemical and thermomechanical stability of the CMC, as well as excellent interfacial bonding between the CMC liner and the underlying C/C structure. In particular, hafnium-containing CMCs on C/C were shown to perform well at temperatures exceeding 3,500 F (.1,925 C). The melt-infiltrated CMC-lined C/C composites offered a lower density than Cf/SiC. The melt-infiltrated composites offer greater use temperature than Cf/SiC because of the more refractory ceramic matrices and the C/C substructure provides greater high-temperature strength. The progress made in this work will allow multiple high-temperature components used in oxidizing environments to take advantage of the low density and high strength of C/C combined with the high-temperature oxidation resistance of melt-infiltrated CMCs.

Wright, Matthew J.↗

NASA NTRSDate not supplied

Refractory Carbides for Hydrogen Erosion Resistance in Carbon Tubes for Nuclear Thermal Propulsion

As crewed travel becomes more common to the Moon and beyond, space nuclear propulsion-based craft offer reduced travel times and double the specific impulse compared to conventional chemical rockets. The nuclear core and its integral hydrogen propellant channels will require advanced refractory carbide coatings over a carbon/carbon substrate for hydrogen resistance. Using ab initio and other computational techniques, we studied select (Zr/Ta/Nb)C mixed carbide systems for erosion resistance and hydrogen diffusion using realistic levels of carbon vacancies and experimentally obtainable stoichiometries. Various contributions to the formation and hydrogen erosion free energies were calculated, including configurational, electronic, and vibrational terms. Our calculations indicate that ZrC is less likely to lose carbon than NbC or TaC, providing an explanation for heritage NERVA data on ZrC and NbC mass loss performance. Additionally, binary mixtures show compositions that are more stable than their end-member counterparts. Hydrogen diffusion in stoichiometric ZrC was found to be slightly higher than previously theorized, with the caveat that hydrogen saturation of carbon vacancies will hinder further hydrogen diffusion through the bulk, while hydrogen diffusion in ZrNbC is slightly enhanced over ZrC. And finally, we show that as carbon is depleted, the deformation mechanism of ZrC changes from brittle to ductile. Though many questions still remain as to the bulk performance of these materials, these trends and results are important in terms of materials selection efforts for hydrogen-resistant coatings on carbon/carbon substrates.

William C Tucker↗

NASA NTRSDate not supplied

Refractory Carbides for Hydrogen Erosion Resistance in Carbon Tubes for Nuclear Thermal Propulsion

As crewed travel becomes more common to the Moon and beyond, space nuclear propulsion-based craft offer reduced travel times and double the specific impulse compared to conventional chemical rockets. The nuclear core and its integral hydrogen propellant channels will require advanced refractory carbide coatings over a carbon/carbon substrate for hydrogen resistance. Using ab initio and other computational techniques, we studied select (Zr/Ta/Nb)C mixed carbide systems for erosion resistance and hydrogen diffusion using realistic levels of carbon vacancies and experimentally obtainable stoichiometries. Various contributions to the formation and hydrogen erosion free energies were calculated, including configurational, electronic, and vibrational terms. Our calculations indicate that ZrC is less likely to lose carbon than NbC or TaC, providing an explanation for heritage NERVA data on ZrC and NbC mass loss performance. Additionally, binary mixtures show compositions that are more stable than their end-member counterparts. Hydrogen diffusion in stoichiometric ZrC was found to be slightly higher than previously theorized, with the caveat that hydrogen saturation of carbon vacancies will hinder further hydrogen diffusion through the bulk, while hydrogen diffusion in ZrNbC is slightly enhanced over ZrC. And finally, we show that as carbon is depleted, the deformation mechanism of ZrC changes from brittle to ductile. Though many questions still remain as to the bulk performance of these materials, these trends and results are important in terms of materials selection efforts for hydrogen-resistant coatings on carbon/carbon substrates.

William C Tucker↗

NASA NTRS2004

Research Performed within the Non-Destructive Evaluation Team at NASA Glenn Research Center

Non-destructive testing is essential in many fields of manufacturing and research in order to perform reliable examination of potentially damaged materials and parts without destroying the inherent structure of the materials. Thus, the Non-Destructive Evaluation (NDE) Team at NASA Glenn Research Center partakes in various projects to improve materials testing equipment as well as analyze materials, material defects, and material deficiencies. Due to the array of projects within the NDE Team at this time, five research aims were supplemental to some current projects. A literature survey of "DE and testing methodologies as related to rocks was performed. Also, Mars Expedition Rover technology was assessed to understand the requirements for instrumentation in harsh space environments (e.g. temperature). Potential instrumentation and technologies were also considered and documented. The literature survey provided background and potential sources for a proposal to acquire funding for ultrasonic instrumentation on board a future Mars expedition. The laboratory uses a Santec Systems AcousticScope AS200 acoustography system. Labview code was written within the current program in order to improve the current performance of the acoustography system. A sample of Reinforced Carbon/Carbon (RCC) material from the leading edge of the space shuttle underwent various non-destructive tests (guided wave scanning, thermography, computed tomography, real time x-ray, etc.) in order to characterize its structure and examine possible defects. Guided wave scan data of a ceramic matrix composite (CMC) panel was reanalyzed utilizing image correlations and signal processing variables. Additional guided wave scans and thermography were also performed on the CMC panel. These reevaluated data and images will be used in future presentations and publications. An additional axis for the guided wave scanner was designed, constructed, and implemented. This additional axis allowed incremental spacing of the previously fixed transducers for ultrasonic velocity measurements.

Burns, Erin A.↗

NASA NTRSDate not supplied

Refractory Carbides for Hydrogen Erosion Resistance in Carbon Tubes for Nuclear Thermal Propulsion

As crewed travel becomes more common to the Moon and beyond, space nuclear propulsion-based craft offer reduced travel times and double the specific impulse compared to conventional chemical rockets. The nuclear core and its integral hydrogen propellant channels will require advanced refractory carbide coatings over a carbon/carbon substrate for hydrogen resistance. Using \textit{ab initio} and other computational techniques, we studied select (Zr/Ta/Nb)C mixed carbide systems for erosion resistance and hydrogen diffusion using realistic levels of carbon vacancies and experimentally obtainable stoichiometries. Various contributions to the formation and hydrogen erosion free energies were calculated, including configurational, electronic, and vibrational terms. Our calculations indicate that ZrC is less likely to lose carbon than NbC or TaC, providing an explanation for heritage NERVA data on ZrC and NbC mass loss performance. Additionally, binary mixtures show compositions that are more stable than their end-member counterparts. Hydrogen diffusion in stoichiometric ZrC was found to be slightly higher than previously theorized, with the caveat that hydrogen saturation of carbon vacancies will hinder further hydrogen diffusion through the bulk, while hydrogen diffusion in ZrNbC is slightly enhanced over ZrC. And finally, we show that as carbon is depleted, the deformation mechanism of ZrC changes from brittle to ductile. Though many questions still remain as to the bulk performance of these materials, these trends and results are important in terms of materials selection efforts for hydrogen-resistant coatings on carbon/carbon substrates.

William C. Tucker↗

NASA NTRS2019

TUFROC Thermal Protection System

Toughened Unipiece Fibrous Reinforced Oxidation-resistant Composite (TUFROC) is a tiled Thermal Protection System (TPS) suitable for reusable entry heating at 2900+ °F and with single use potential up to at least 3600 °F. TUFROC was initially developed for NASA's X-37 project and ultimately resulted in use on the Air Force X-37B as the wing leading edge (WLE) of the vehicle. TUFROC has similar high temperature capability compared with carbon/carbon, but is manufactured at an order of magnitude lower cost & faster schedule.

thermal protection system↗

NASA NTRS2019

Computational Materials Techniques for Thermal Protection Solutions: Materials and Process Design

Integrated computational materials techniques that span the atomistic and continuum scales have the potential to aid the design and manufacturing of thermal protection materials. Two cases demonstrating the practical application of these methods are discussed. Case one examines the selection of a high temperature coating for carbon/carbon, with the target application being a solar thermal propulsion heat exchanger. The performance of various refractory metal and metal-carbide coatings is characterized considering extreme thermal (3500 K) and chemical (hydrogen flows) conditions. The recession rate, hydrogen leakage, and likelihood of mechanical failure are characterized and provide directions for further experimental investigation. Case two examines the process optimization of a heat shield material composed of a woven silica fiber preform and cyanate ester resin. Frequently, internal voids were found to be present in this composite after the resin infusion and curing stages of manufacturing. Using the manufacturing conditions, computations indicate that both water adsorption and resin cure shrinkage are contributing factors to void formation. The results suggest an alternative process configuration for curing that would mitigate voids.

thermal protection↗

NASA NTRS2018

Computational Materials Techniques for Thermal Protection Solutions: Materials and Process Design

Integrated computational materials techniques that span the atomistic and continuum scales have the potential to aid the design and manufacturing of thermal protection materials. Two cases demonstrating the practical application of these methods are discussed. Case one examines the selection of a high temperature coating for carbon/carbon, with the target application being a solar thermal propulsion heat exchanger. The performance of various refractory metal and metal-carbide coatings is characterized considering extreme thermal (3500 K) and chemical (hydrogen flows) conditions. The recession rate, hydrogen leakage, and likelihood of mechanical failure are characterized and provide directions for further experimental investigation. Case two examines the process optimization of a heat shield material composed of a woven silica fiber preform and cyanate ester resin. Frequently, internal voids were found to be present in this composite after the resin infusion and curing stages of manufacturing. Using the manufacturing conditions, computations indicate that both water adsorption and resin cure shrinkage are contributing factors to void formation. The results suggest an alternative process configuration for curing that would mitigate voids.

Haskins, Justin↗

NASA NTRS2019

Computational Materials Techniques for Thermal Protection Solutions: Materials and Process Design

Integrated computational materials techniques that span the atomistic and continuum scales have the potential to aid the design and manufacturing of thermal protection materials. Two cases demonstrating the practical application of these methods are discussed. Case one examines the selection of a high temperature coating for carbon/carbon, with the target application being a solar thermal propulsion heat exchanger. The performance of various refractory metal and metal-carbide coatings is characterized considering extreme thermal (3500 degrees Kelvin) and chemical (hydrogen flows) conditions. The recession rate, hydrogen leakage, and likelihood of mechanical failure are characterized and provide directions for further experimental investigation. Case two examines the process optimization of a heat shield material composed of a woven silica fiber preform and cyanate ester resin. Frequently, internal voids were found to be present in this composite after the resin infusion and curing stages of manufacturing. Using the manufacturing conditions, computations indicate that both water adsorption and resin cure shrinkage are contributing factors to void formation. The results suggest an alternative process configuration for curing that would mitigate voids.

Thermal Protection↗

NASA NTRS1993

Acoustic radiation damping of flat rectangular plates subjected to subsonic flows

The acoustic radiation damping for various isotropic and laminated composite plates and semi-infinite strips subjected to a uniform, subsonic and steady flow has been predicted. The predictions are based on the linear vibration of a flat plate. The fluid loading is characterized as the perturbation pressure derived from the linearized Bernoulli and continuity equations. Parameters varied in the analysis include Mach number, mode number and plate size, aspect ratio and mass. The predictions are compared with existing theoretical results and experimental data. The analytical results show that the fluid loading can significantly affect realistic plate responses. Generally, graphite/epoxy and carbon/carbon plates have higher acoustic radiation damping values than similar aluminum plates, except near plate divergence conditions resulting from aeroelastic instability. Universal curves are presented where the acoustic radiation damping normalized by the mass ratio is a linear function of the reduced frequency. A separate curve is required for each Mach number and plate aspect ratio. In addition, acoustic radiation damping values can be greater than or equal to the structural component of the modal critical damping ratio (assumed as 0.01) for the higher subsonic Mach numbers. New experimental data were acquired for comparison with the analytical results.

Lyle, Karen Heitman↗

NASA NTRS2003

Studies Conducted of Sodium Carbonate Contaminant Found on the Wing Leading Edge and the Nose Cap of the Space Shuttle Orbiter

In early 2001, three of the space shuttle orbiters were found to have a sodium carbonate contaminant on the wing leading edge and nose cap. These parts are made of a reinforced carbon/carbon material protected by silicon carbide (SiC) and a glass coating. The glass coating is known as Type A and is primarily sodium silicate with particles of SiC. NASA Glenn Research Center's Environmental Durability Branch was asked to determine the chemistry of this deposit formation and assess any possible detrimental effects. At low temperatures, the reverse reaction is favorable. Previous studies of the corrosion of glass show that carbon dioxide in the presence of water does form sodium carbonate on sodium silicate glass (ref. 1). It is quite likely that a similar scenario exists for the orbiter wing leading edge. All three orbiters that formed sodium carbonate were exposed to rain. This formation of sodium carbonate was duplicated in the laboratory. The Type A glass, which coats the wing leading edge and nose cap, was made in a freestanding form and exposed to water in two separate experiments. In one set of experiments, the coating was placed in a petri dish filled with water. As the water evaporated, sodium carbonate formed. In another case, water was slowly dripped on the coating and sodium carbonate formed. The sodium carbonate was detected by chemical analysis and, in some cases, xray diffraction showed a hydrated sodium carbonate. The next step was to examine possible detrimental effects of this sodium carbonate. There are three likely scenarios for the sodium carbonate deposit: (1) it may be removed with a simple rinse, (2) it may remain and flow back into the Type A glass after heating during reentry, or (3) it may remain and flow onto unprotected SiC and/or other parts after heating during reentry. The effect of case 1 is to remove the Na2O constituent from the Type A glass, thus decreasing its effectiveness as a sealant. Even so, overall, it is probably the best approach and was used by the NASA Kennedy Space Center when the deposits were first observed. The effect of case 2 is minimal and would actually restore the the Type A glass to its composition before carbonate formation. However, the problem with allowing the carbonate to remain leads to the third scenario, the deposit flowing onto other parts. A series of tests were conducted on unprotected SiC, and minimal effects were found in the short-term, but other ceramic and metal parts could be damaged by the molten sodium carbonate and would require close monitoring.

Jacobson, Nathan S.↗