Search NASA⌕ Search

SEARCH · Search NASA

Results for “CdTe solar cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Investigation of Sub‐Bandgap Emission and Unexpected n‐Type Behavior in Undoped Polycrystalline CdSe x Te 1‐x

Abstract Se alloying has enabled significantly higher carrier lifetimes and photocurrents in CdTe solar cells, but these benefits can be highly dependent on CdSe x Te 1‐x processing. This work evaluates the optoelectronic, chemical, and electronic properties of thick (3 µm) undoped CdSe x Te 1‐x of uniform composition and varied processing conditions (CdSe x Te 1‐x evaporation rate, CdCl 2 anneal, Se content) chosen to reflect various standard device processing conditions. Sub‐bandgap defect emission is observed, which increased as Se content increased and with “GrV‐optimized CdCl 2 ” (i.e., CdCl 2 anneal conditions used for group‐V‐doped devices). Low carrier lifetime is found for GrV‐optimized CdCl 2 , slow CdSe x Te 1‐x deposition, and low‐Se films. Interestingly, all films (including CdTe control) exhibited n‐type behavior, where electron density increased with Se up to an estimated ≈10 17 cm −3 . This behavior appears to originate during the CdCl 2 anneal, possibly from Se diffusion leading to anion vacancy (e.g., V Se , V Te ) and Cl Te generation.

14 SOLAR ENERGY↗
DOE OSTI2025

Nm-scale electrical resistance imaging on CdTe by scanning spreading resistance microscopy

Local resistance imaging can provide information on nm-scale carrier distribution in semiconductor devices. Scanning spreading resistance microscopy (SSRM), an atomic force microscopy-based nm-scale resistance mapping technique, has been developed for carrier delineation in Si microdevices. We report on the development and validation of SSRM on CdTe materials, by testing on molecular beam epitaxy (MBE) grown CdTe films. The probe/CdTe contact resistance was suppressed sufficiently below sample's spreading resistance by pressing the probe into the sample with ∼mN contact force and applying a large sample/probe forward bias voltage (V s ), which was understood by analyzing current-voltage (I-V) involving a serially connected insulating top layer with underlying spreading resistance. The carrier concentration as deduced from the resistance measurement, using a single mobility value, is consistent with Hall measurement with a standard deviation of 14% based on a set of MBE films with carrier concentrations in the range of 10 15 –10 16 /cm 3 . The doping polarity was readily identified by flipping V s polarity, where the resistance with reverse V s is orders of magnitude larger than forward V s . While focusing on the SSRM technique validation, we also show an example on an As-doped Cd(Se,Te) polycrystalline thin film of a high-performance CdTe solar cell, which illustrates the local resistance nonuniformity with up to two orders of magnitude differences, indicating if local mobility is roughly constant, local carrier concentration can have significant nonuniformity.

14 SOLAR ENERGY↗
DOE OSTI2024

Development of an Optical Library for Coevaporated CdSe x Te 1– x

The conversion efficiency of CdTe solar cells may be improved by bandgap engineering, i.e., changing the bandgap value through the addition of Se in the absorber. The Se alloying enables a short-circuit current density improvement, as it leads to a bandgap energy value decrease. Furthermore, it has been associated with increased minority carrier lifetimes, assuring high open-circuit voltage values. An Se gradient profile control can further optimize the solar cell performance. Thus, an optical model baseline of the CdSe x Te 1–x (CST) compound was developed. Spectroscopic ellipsometry measurements were conducted to accurately extract the optical constants of ten CST layers deposited through coevaporation with x varying from 0 to 1. Using the measured dielectric function spectra from the discrete CST layers with varying x, and considering the composition-induced shift in the critical point energies, an energy-shift model was employed to develop the accurate optical library for the CST compound for any x value to provide data for future modeling and optimization. Furthermore, the library accuracy was validated through optical simulations of the quantum efficiency of a graded CST solar cell using the finite-difference time-domain method by replicating the Se profile in the absorber layer measured through secondary ion mass spectrometry.

14 SOLAR ENERGY↗
DOE OSTI2020

Thin-Film Solar Cells with 19% Efficiency by Thermal Evaporation of CdSe and CdTe

CdTe-based solar cells exhibiting 19% power conversion efficiency were produced using widely available thermal evaporation deposition of the absorber layers on SnO2-coated glass with or without a transparent MgZnO buffer layer. Evaporating CdSe and CdTe sequentially by thermal evaporation and subsequent CdCl2 annealing establishes efffective CdSeTe band grading as well as dense, large-grain films. These results show that high-performance II-VI photovoltaics can be made by inexpensive, commercially available evaporation systems without the need to build customized equipment, enabling CdTe photovoltaics research and manufacturing to be more accessible to the broader photovoltaics community.

14 SOLAR ENERGY↗
NASA NTRS2001

Annealing of Solar Cells and Other Thin Film Devices

Annealing is a key step in most semiconductor fabrication processes, especially for thin films where annealing enhances performance by healing defects and increasing grain sizes. We have employed a new annealing oven for the annealing of CdTe-based solar cells and have been using this system in an attempt to grow US on top of CdTe by annealing in the presence of H2S gas. Preliminary results of this process on CdTe solar cells and other thin-film devices will be presented.

Escobar, Hector↗
DOE OSTI2021

Sputter-deposited CdMgTe for rear contact to CdSeTe/CdTe solar cells

CdTe-based photovoltaic device performance improvement is predominantly limited by open-circuit voltage. This work approaches the voltage deficit challenge through the incorporation of a cadmium magnesium telluride (CdMgTe) electron reflector layer at the back of 1.5- μm CdSeTe/CdTe absorbers to reduce back-surface recombination through a conduction band offset. A sputtered CdMgTe electron reflector layer permitted low fabrication temperatures and circumvented the intolerance of CdMgTe to thermal processing present in traditional close-space sublimation (CSS)-deposited CdMgTe devices. Here, we demonstrate that sputtered CdMgTe simultaneously promotes the retention of chlorine passivation and magnesium which is not feasible with CSS fabrication. We also show the importance of the Cu and Te back contact order in CdMgTe devices. Through the optimization of the sputtered CdMgTe substrate temperature, doping, and back structure configuration, 1.5 μm CdSeTe/CdTe devices with a sputtered CdMgTe layer achieved an efficiency of 16.0%, significantly higher than with CSS CdMgTe, and demonstrated partial enactment of electron-reflector behavior.

14 SOLAR ENERGY↗
DOE OSTI2026

Understanding Recombination Pathways of CdSeTe/CdTe Devices Using Temperature Dependence of Fill Factor

Understanding the temperature dependence of photovoltaic parameters is critical for identifying performance limiting mechanisms in CdTe-based solar cells. In this study, we investigate the temperature dependence of fill factor (FF(T)) in CdSeTe/CdTe solar cells using a combination of experimental current density-voltage (JV) measurements and numerical simulations. The measured FF(T) exhibits a nonlinear response with temperature, peaking at moderate temperature values (10–30°C). Through numerical modeling, we reveal that this peaking behavior in FF(T) arises when the dominant recombination mechanism transitions from bulk to interface with increasing temperature. This transition is primarily driven by low hole mobility (0.6–1.2 cm2/V·s), while electron mobility, interface recombination velocities, and carrier lifetime also contribute to the effect. Our findings demonstrate that FF(T) analysis is a promising diagnostic tool for distinguishing recombination pathways and guiding the optimization of thin-film CdTe solar cells under real-world conditions.

CdTe photovoltaics↗
DOE OSTI2020

A Density Functional Theory (DFT) Study on the Effect of Chlorine in the Magnesium Zinc Oxide (MZO) Front Interface for Cadmium Telluride (CdTe) Thin Film Solar Cells

Cadmium telluride photovoltaics has benefitted greatly from the cadmium chloride treatment which causes a remarkable improvement in cell efficiencies. This work investigates the effect of elemental chlorine at the interface between the magnesium zinc oxide front contact and the cadmium telluride absorber in such a device. Band alignment including band bending and interface states and its role in potential charge carrier transport is the key feature studied. It is seen that a small amount of chlorine is leads to a more desirable band alignment. Higher concentrations of chlorine result in unfavorable band characteristics.

14 SOLAR ENERGY↗
NASA NTRS1989

High-efficiency CdTe thin-film solar cells using metalorganic chemical vapor deposition techniques

Energy conversion efficiency of metalorganic chemical vapor deposited CdTe as an intrinsic active layer in n-i-p solar cell structures is reported. Small-area devices with efficiencies over 9 percent have been demonstrated. I-V characteristics, photospectral response, and the results of Auger profiling of structural composition for typical devices will be presented. Also presented are preliminary results on similar photovoltaic devices having Cd(0.85)Mn(0.15)Te in place of CdTe as an i layer.

Nouhi, A.↗
DOE OSTI2025

CdSeTe solar-cell performance with different dopant types

Four doping conditions were explored for CdTe-based solar cells: p-type As and P, n-type Al, and no intentional doping. In each case, the CdTe absorber was alloyed with Se, but only near the normal front-side, light entry for the cells, while the dopants were added from the back. Cells with p-dopants showed efficiencies up to 20% with front-side illumination, but the n-doped and undoped ones were close to zero. With back-side illumination, this was reversed with undoped up to 8% and p-doped ones only about 2%. These results are explained by Kelvin-probe measurements of electric-field profiles, which showed that the diode field was near the front for the higher-efficiency p-doping, but near the back for undoped and n-doped.

14 SOLAR ENERGY↗
DOE OSTI2026

Impact of the Annealing Temperature on the Local Se Distribution and Optical Properties in CdSexTe1-x Solar Cells by Multimodal X-ray Microscopy

The introduction of Se in CdTe solar-cell absorbers has led to multiple beneficial effects in the devices, including an increased short-circuit current and an extended charge-carrier lifetime. A critical manufacturing step of CdSexTe1-x solar cells is CdCl2 annealing at high temperatures, during which Se diffuses through the absorber layer. Understanding the local Se distribution in the absorber and its impact on optical properties of the material is key for the further development of this thin-film solar cell technology. In a multimodal x-ray scanning microscopy approach, we investigated the impact of the annealing temperature of CdSexTe1-x solar cells on the Se distribution and on optical characteristics of the material. For this purpose, we exploited an upgraded x-ray excited optical luminescence (XEOL) detection unit that enables simultaneous spectrally and temporally resolved XEOL mapping at synchrotron facilities that are ideal for studying thin-film solar-cell materials with hard x-rays featuring high penetration depth and lateral resolution.

14 SOLAR ENERGY↗
DOE OSTI2021

Distinguishing bulk and surface recombination in CdTe thin films and solar cells using time-resolved terahertz and photoluminescence spectroscopies

Understanding the nature of recombination and its dependence on defects and interfaces is essential for engineering materials and contacts for higher open circuit voltage (V oc ) and power conversion efficiency in photovoltaic (PV) devices. Time-resolved photoluminescence (TRPL) has conventionally been used to evaluate recombination, but carrier redistribution often dominates the response at short times. In this work, we report on the quantification of carrier dynamics and recombination mechanisms by complementary use of both time-resolved terahertz spectroscopy (TRTS) and TRPL combined with numerical modeling of the continuity equations and Poisson’s equation. We have demonstrated this approach using CdTe thin films. A thin film stack with CdTe fabricated by vapor transport deposition and treated with CdCl 2 exhibited a bulk lifetime of 1.7 ± 0.1 ns, negligible CdTe/CdS interface recombination velocity, and back surface recombination velocity of 6.3 ± 1.3 x10 4 cm/s. In contrast, a film stack without CdCl 2 treatment had a bulk lifetime of only 68 ± 12 ps and a higher interface recombination velocity of 4 ± 2 x10 8 cm/s. By determining the locus and mechanisms of performance-limiting recombination, we can accelerate the development of thin-film PVs with higher V oc and efficiency. While the method has been demonstrated here using CdTe, it is also applicable to perovskites, Cu(InGa)Se 2 , Cu2ZnSn(S,Se) 4, and emerging technologies.

14 SOLAR ENERGY↗
DOE OSTI2022

Hybrid Functional Calculations for Antimony Doping in CdTe

CdTe-based solar cells are leading thin-film photovoltaic technology, with efficiencies over 22%, but still much lower than the theoretical maximum of 29%. Further improvements will rely on increasing the open-circuit voltage Voc, which, in turn, depends on carrier density and lifetime. Using hybrid density functional calculations, we investigate Sb doping of CdTe, focusing on its limitation as shallow acceptor and the formation of compensating AX center. Paying special attention to supercell size and effects of spin-orbit coupling, we predict an ionization energy of 116 meV in the dilute limit, much closer to recent experimental value of 103 meV from temperature-dependent Hall measurements in bulk single crystals, and in contrast to much larger values from previous calculations. We also find that the Sb-related AX centers are not major compensation centers in Sb-doped CdTe.

14 SOLAR ENERGY↗
DOE OSTI2021

Robust passivation of CdSeTe based solar cells using reactively sputtered magnesium zinc oxide

Magnesium zinc oxide (MZO, Mg x Zn 1-x O) is a leading emitter for CdTe-based solar cells due to its transparency and the ability to tune its conduction band offset with the absorber. Devices employing alloyed cadmium selenide telluride (CST, CdSe y Te 1-y ) absorbers achieved high efficiency (>19%) using MZO deposited by reactive sputtering over a broad composition range (3.68–3.92 eV, x: 0.20–0.35). Minimal differences in implied and measured open circuit voltage indicate that the contacts are well passivated and highly selective across the spectrum of MZO employed. Device performance insensitivity to MZO composition, which is not observed in CdTe devices, is attributed to the formation of an oxygenated interface layer. Se volatility creates a group VI deficiency at the interface that drives O migration from the MZO into the absorber. This introduces conductivity in the emitter not present in its as-deposited state, contributing to the exceptional performance observed. It is shown that the quality of device passivation depends on the oxidation state of the as-deposited MZO such that intelligent control and management of the reactive sputtering process is required.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In 2 O 3 -Ga 2 O 3 Alloys as Potential Buffer Layers in CdTe Thin-Film Solar Cells

The efficiency of state-of-the-art Cd Te solar cells remains limited by the relatively low open-circuit voltage (V OC ). Improving the front interface is key towards realizing a higher V OC after achieving the necessary bulk carrier density and lifetime. Recent efforts in identifying buffer layers beyond Cd S have focused on Mg x Zn 1-x O, which offers tunability of the band offsets, but often suffers from high interfacial defect densities. Ga 2 O 3 -based buffer layers demonstrate tremendous improvements in interfacial defect passivation in crystalline silicon and dye-sensitized solar cells, leading to record high V OC , yet remain largely unexplored in Cd Te-based devices. Here, we perform hybrid density-functional-theory calculations to investigate pure Ga 2 O 3 and InGaO 3 alloys as a window layer in Cd Te photovoltaics. We report calculated band offsets for several pairs of solid-solid interfaces comprising transparent conducting oxide (TCO) and Cd Te heterojunctions. The results support a large conduction band offset spike of 0.67 eV for the Cd Te/Ga 2 O 3 (100) interface, while the offset is reduced to 0.18 eV for the InGaO 3 alloy and matches closely with the preferred optimum value of 0.2 eV. Device-level modeling tests of Cd Te solar cells integrating our results indicate that the highest efficiency is achieved with InGaO 3 acting both as a buffer layer and TCO. Finally, our results suggest that alloys of In 2 O 3 and Ga 2 O 3 may be attractive alternatives to Mg x Zn 1-x O for tailoring optimal conduction-band offsets of the buffer and TCO layers in high-efficiency Cd Te thin-film solar cells.

14 SOLAR ENERGY↗
DOE OSTI2026

Identifying Suitable Front Contacts for High‐Efficiency Cd(Se,Te) Solar Cells on Space‐Qualified Cover Glass

Deployment of photovoltaics in space requires devices that combine high-efficiency, low areal mass, and resilience to harsh environments. Historically, high-efficiency multijunction III–V materials have dominated space power systems; however, their high cost and limited manufacturing throughput motivate the exploration of scalable alternatives. While CdTe-based thin-film photovoltaics offer an attractive option, their performance on non-conventional substrates can suffer from front contact instability under higher-temperature processing. Here, the role of front contact chemistry in limiting cell performance is investigated using CdTe-based devices fabricated on 150 μm thick Ceria-doped space-qualified 0214 Corning glass. A matrix of four transparent conducting oxides (TCOs: CTO, AZO, ITO, IZO) combined with two n-type emitters (MZO, IGO) reveals chemical stability at the front interface—rather than absorber composition alone—governs recombination losses, voltage deficits, and device reproducibility. Chemically stable front contact combinations suppress elemental diffusion and interfacial degradation, resulting in significantly improved carrier lifetimes and junction quality. These insights are validated through record-certified Cd(Se,Te) cell efficiencies of 18.4% under AM1.5G and 16.2% under AM0 illumination on ultra-thin glass. Beyond CdTe, this work provides a general framework for the rational selection of TCO/emitter interfaces in superstrate thin-film photovoltaics, including emerging technologies like metal halide perovskites, while enabling high-efficiency, lightweight photovoltaics for space applications.

14 SOLAR ENERGY↗