Search NASA⌕ Search

SEARCH · Search NASA

Results for “Chemical explosives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

DNS of ignition and flame stabilization in a simplified gas turbine premixer

With the increasing need for fuel flexibility, mitigation of auto-ignition (AI) inside gas turbine (GT) premixers becomes crucial. They must be designed to yield a sufficiently homogeneous fuel-air mixture to achieve low emissions while at the same time avoiding the occurrence of AI and subsequent flame stabilization. This challenge requires a detailed understanding of turbulent mixing and chemistry interactions. In the present work, a direct numerical simulation (DNS) of an array of jets in crossflow (JICF), representative of an industrial GT premixer, is reported to shed light on these complex phenomena. It is found that AI kernels form in the aft part of the premixer and coalesce into a flame front that then propagates upstream, mainly through the boundary layer, and successively engulfs the jets. This, therefore, suggests a significant role of the jet array pattern on the flame stabilization. It is noted that AI kernels continue to form independently during the whole time of the simulation. To clarify the contribution of AI and diffusion in the ignition kernels and the main flame, chemical explosive mode analysis (CEMA) is employed jointly with a kernel tracking algorithm. It is found that during the initial formation of the flame, many ignition kernels form in mixtures with low scalar dissipation rate and large contribution from AI mode. As they quickly grow, they merge into a single flame front that becomes increasingly more diffusion-assisted over time, balancing the AI mode. Turbulence is shown to have a significant enhancing effect in lean premixed flames, but further analysis is required to fully characterize it. These findings are relevant for the industrial premixer studied, and also for novel micromix concepts that may be used in the next generation of GT combustion systems.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Comparative Analysis of Explosion Signals on Smartphones and Seismometers [Poster]

Seismoacoustic signatures from a chemical explosion was recorded on two seismometers and eight smartphone accelerometers at Idaho National Laboratory (INL). The captured waveform’s propagation and its time frequency representations are compared. The smartphone accelerometers were able to pick up a clear seismoacoustic explosion signal at within 1 km (150 m/kg 1/3 ) and a noisy signal up to 5.3 km (790 m/kg 1/3 ).

98 - NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL↗
DOE OSTI2021

Imaging the Shallow Structure of the Yucca Flat at the Source Physics Experiment Phase II Site with Horizontal-to-Vertical Spectral Ratio Inversion and a Large- N Seismic Array

The Source Physics Experiment (SPE) is a series of chemical explosions at the Nevada National Security Site (NNSS) with the goal of understanding seismic-wave generation and propagation of underground explosions. To understand explosion source physics, accurate geophysical models of the SPE site are needed. Here, we utilize a large-N seismic array deployed at the SPE phase II site to generate a shallow subsurface model of shear-wave velocity. The deployment consists of 500 geophones and covers an area of, approximately, 2.5 × 2 km. The array is located in the Yucca Flat in the northeast corner of the NNSS, Nye County, Nevada. Using ambient-noise recordings throughout the large-N seismic array, we calculate horizontal-to-vertical spectral ratios (HVSRs) across the array. We obtain 2D seismic images of shear-wave velocities across the SPE phase II site for the shallow structure of the basin. In this work the results clearly image two significant seismic impedance interfaces at ~150–500 and ~350–600 m depth. The shallower interface relates to the contrast between Quaternary alluvium and Tertiary volcanic rocks. The deeper interface relates to the contrast between Tertiary volcanic rocks and the Paleozoic bedrock. The 2D subsurface models support and extend previous understanding of the structure of the SPE phase II site. This study shows that the HVSR method in conjunction with a large-N seismic array is a quick and effective method for investigating shallow structures.

58 GEOSCIENCES↗
DOE OSTI2026

Detection and imaging of chemicals and hidden explosives using terahertz time-domain spectroscopy and deep learning

Detecting concealed chemicals and explosives remains a critical challenge in global security. Terahertz time-domain spectroscopy (THz-TDS) offers a promising non-invasive and stand-off detection technique owing to its ability to penetrate optically opaque materials without causing ionization damage. While many chemicals exhibit distinct spectral features in the terahertz range, conventional terahertz-based detection methods often struggle in real-world environments, where variations in sample geometry, thickness, and packaging can lead to inconsistent spectral responses. In this study, we present a chemical imaging system that integrates THz-TDS with deep learning to enable accurate pixel-level identification and classification of different explosives. Operating in reflection mode and enhanced with plasmonic nanoantenna arrays, our THz-TDS system achieves a peak dynamic range of 96 dB and a detection bandwidth of 4.5 THz, supporting practical, stand-off operation. By analyzing individual time-domain pulses with deep neural networks, the system exhibits strong resilience to environmental variations and sample inconsistencies. Blind testing across eight chemicals—including pharmaceutical excipients and explosive compounds—resulted in an average classification accuracy of 99.42% at the pixel level. Notably, the system maintained an average accuracy of 88.83% when detecting explosives concealed under opaque paper coverings, demonstrating its robust generalization capability. These results highlight the potential of combining advanced terahertz spectroscopy with neural networks for highly sensitive and specific chemical and explosive detection in diverse and operationally relevant scenarios.

Imaging and sensing↗
DOE OSTI2020

Simulations of the Large Surface Explosion Coupling Experiment (LSECE)

The Large Surface Explosion Coupling Experiment (LSECE) project will include two surface energetic events (chemical explosions) conducted as close as possible to ground zero (GZ) of the Source Physics Experiment (SPE) Phase II Dry Alluvium (DAG) site in Yucca Flat at the Nevada National Security Site (NNSS). Seismic and acoustic data from these events will complement DAG buried source data and improve interpretation of speed-of-sound signals from explosions for national security programs. A satellite image of the region near GZ along with some of the recording stations that we will use for the far- eld simulation is shown in Figure 1. The working design of the HE package is shown in the Figure 2 and is roughly a cube of C-4 bricks.

58 GEOSCIENCES↗
DOE OSTI2022

Identification of Acoustic Wave Signatures in the Ionosphere From Conventional Surface Explosions Using MF/HF Doppler Sounding

Here, we present an experiment to detect one ton TNT-equivalent chemical explosions using pulsed Doppler radar observations of isodensity layers in the ionospheric E region during two campaigns. The first campaign, conducted on 15 October 2019, produced potential detections of all three shots. The detections closely resemble the temporal and spectral properties predicted using the InfraGA ray tracing and weakly nonlinear waveform propagation model. Here the model predicts that within 6.5–7.25 min of each shot a waveform peaking between 0.9 and 0.4 Hz will impact the ionosphere at 100 km. As the waves pass through this region, they will imprint their signal on an isodensity layer, which is detectable using a Doppler radar operating at the plasma frequency of the isodensity. Within the time windows of each of the three shots in the first campaign, we detect enhanced wave activity peaking near 0.5 Hz. These waves were imprinted on the Doppler signal probing an isodensity layer at 2.785 MHz near 100 km altitude. Despite these detections, the method appears to be unreliable as none of the six shots from the second campaign, conducted on 10 July 2020 were detected. The observations from this campaign were characterized by an increased acoustic noise environment in the microbarom band and persistent scintillation on the radar returns. These effects obscured any detectable signal from these shots and the baseline noise was well above the detection levels of the first campaign.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Fracture Network Influence on Rock Damage and Gas Transport following an Underground Explosion

Simulations of rock damage and gas transport following underground explosions that omit preexisting fracture networks in the subsurface cannot fully characterize the influence of geo-structural variability on gas transport. Previous studies do not consider the impact that fracture network structure and variability have on gas seepage. In this study, we develop a sequentially coupled, axi-symmetric model to look at the damage pattern and resulting gas breakthrough curves following an underground explosion given different fracture network realizations. We simulate 0.327 and 0.164 kT chemical explosives with burial depths of 100 m for 90 stochastically generated fracture networks. Gases quickly reach the surface in 30% of the higher yield simulations and 5% of the lower yield simulations. The fast breakthrough can be attributed to the formation of connected pathways between fractures to the surface. The formation of a connected damage pathway to the surface is not clearly correlated with the fracture intensity (P32) in our simulations. Breakthrough curves with slower transport are highly variable depending on the fracture network sample. The variability in the breakthrough behavior indicates that ignoring the influence of fracture networks on rock damage, which strongly influences the hydraulic properties following an underground explosion, will likely lead to a large underestimation of the uncertainty in the gas transport to the surface. This work highlights the need for incorporation of fracture networks into models for accurately predicting gas seepage following underground explosions.

58 GEOSCIENCES↗
DOE OSTI2023

Rock Valley Direct Comparison Relocation Working Group Location Results and Recommendations (Version 4.0)

The Source Physics Experiments (SPE) were designed to improve our physics-based understanding of explosion sources for the purposes of nuclear test monitoring. Phase I consisted of 6 chemical explosions in the Climax Stock Granite of the Nevada National Security Site (NNSS), while Phase II consisted of 4 explosions in a contrasting dry alluvium geology (DAG) in Yucca Flat, providing essential data in various media and emplacement conditions to further modeling efforts. For Phase III, the Rock Valley Direct Comparison (RVDC) seeks to directly compare earthquake and explosion source types. An unusually shallow series of events in 1993 along the Rock Valley Fault Zone in the southeastern portion of the NNSS has been targeted for this direct comparison. Depth ranges for the events, previously estimated to be less than 3 km, is achievable by modern drilling techniques and accessibility to the epicentral locations would require minimal improvements to the infrastructure. The events providing this unique opportunity for direct comparison are the focus of this report.

58 GEOSCIENCES↗
DOE OSTI2020

Using SF 6 and Xe to Monitor Gas Migration Through Explosion-Generated Fracture Networks

Here we describe a field study where tracer gas was injected into a subsurface cavity created by a small chemical explosion beneath the water table. The main objective of the study is to compare the migration of sulfur hexafluoride (SF 6 ) and xenon (Xe) through an explosion-generated fracture network and to study the influence of ground water on gas transport. A mixture of tracer gases (50% of SF 6 and 50% of Xe) was injected on 31 October 2018 and gas sampling continued until 8 November 2018. We observe similar trends in SF 6 and Xe concentrations at four ground surface sampling sites. The changes in the SF 6 /Xe ratios with time show that more SF 6 than Xe is observed during the barometric pressure lows when the absolute measured concentrations are highest. Conversely, the ratio SF 6 /Xe is less than 1 during the high-pressure intervals when absolute measured concentrations are low. The results of the experiment suggest that during barometric pressure lows the tracer is migrating to the surface primarily by advective gas phase transport, whereas during barometric pressure highs, advection is suppressed and near-surface evaporation of interstitial pore fluid with tracer dissolved in it becomes more important. Thus, the results of the experiment show that the gas concentrations at the surface are controlled by the combined effects of the gas dissolution into pore water and the barometric pressure fluctuations.

58 GEOSCIENCES↗
DOE OSTI2021

Characteristics of thermospheric infrasound predicted using ray tracing and weakly non-linear waveform analyses

Infrasonic signals refracted by thermal gradients in the rarefied upper atmosphere are modeled using a combination of ray tracing and weak shock theory to develop an understanding of thermospheric infrasound signals produced by energetic, transient sources. Canonical arrival structures in the form of u-wave signatures are identified for returns refracted at lower altitudes within the thermosphere, and possible multi-pathing produced by effective sound speed inflections are investigated to elucidate more complex arrival structures, which are found to be spatially localized. Furthermore, variability in the source characteristics is investigated and it is found that whereas some waveform phase information is lost due to finite amplitude effects, arrival characteristics are strongly dependent on the peak overpressure near the source. Variability in the propagation path is considered using archived atmospheric specifications and implies that despite uncertainties related to the dynamic and sparsely sampled nature of the atmosphere, thermospheric signatures might be useful in estimating the yield for explosive sources. Last, thermospheric arrivals from a failed rocket launch, as well as those from several large chemical explosions, are analyzed and it is found that qualitative trends match those predicted, and analyses here provide additional insight into such signatures.

42 ENGINEERING↗
DOE OSTI2021

Modeling Subsurface Explosions Recorded on a Distributed Fiber Optic Sensor

Fiber optic distributed acoustic sensors (DAS) are becoming a widely used tool for seismic sensing. Here we examine recordings of two subsurface chemical explosions, DAG-1 and DAG-3, each of which was about one metric ton (TNT equivalent), that were recorded from a helical fiber installed in two boreholes 80 m away from the source location. Several clear phases including the initial P wave, a weak S wave, and a surface reflected P wave are observed on the helical DAS data. We estimate a velocity model using arrival times measured from the fiber. The DAS waveform data were compared with colocated accelerometers at specific depths in both frequency and time domains. Furthermore, the spectra of the DAS data matched spectra estimated from the accelerometer records. Comparisons of observed waveform shape between the accelerometer records and the fiber measurements (strain-rate) show reasonable agreement except for the data near the event depth. The DAS data and the accelerometer agreed in relative amplitudes but we had difficulties in matching absolute amplitudes, possibly due to errors in metadata. Synthetic strain-rate waveforms were calculated using a 2D wavenumber algorithm and matched the waveform shape and relative amplitudes. In general, DAS is effective at recording strong ground motions at high spatial density. Comparison of the synthetic seismograms with observed data indicate that the waveforms are not consistent with a pure isotropic explosion source and that the observed S waves originate from very near the source region.

58 GEOSCIENCES↗
DOE OSTI2021

Full Moment Tensor Solutions of U.S. Underground Nuclear Tests for Event Screening and Yield Estimation

Moment tensor (MT) solutions are proving increasingly valuable in explosion monitoring, especially now that they are more routinely calculated for the unconstrained, full (six component) MT. In this study, we have calculated MTs for U.S. underground nuclear tests conducted at the Nevada National Security Site using seismic recordings primarily from the Livermore Nevada Network. We are able to determine them for 130 nuclear explosions from 1970 to 1996 for a range of yields and under a variety of material conditions, which we have supplemented with 10 additional chemical explosions at the test site. The result is an extensive database of MTs that can be used to assess the performance of important monitoring tasks such as event identification and yield determination. We test the explosion event screening on the fundamental lune of the MT eigensphere and find MT screening to be a robust discriminant between earthquakes and explosions. We then explore the estimation of moment-derived yield, in which we find that material properties are the largest contributor to differences in the estimated moment-to-yield ratio. Additionally, further research conducted on this dataset can be used to develop, test, and improve various explosion monitoring methodologies.

58 GEOSCIENCES↗
DOE OSTI2023

Acoustic Waves From a Distant Explosion Recorded on a Continuously Ascending Balloon in the Middle Stratosphere

Abstract A helium‐filled mylar balloon carrying a smartphone and infrasound sensors ascended to a stratospheric height of 35 km over the surface detonation of a chemical explosive, with a total acoustic propagation distance of 127 km. The smartphone was configured to collect multi‐modal data at high rates from internal sensors. Analysis of the data shows successful collection of the explosion signal by both the smartphone's microphone and its accelerometers, the first from an ascending balloon. Comparison of the acoustic signal with that collected by other infrasound sensors, both airborne and ground‐based, provides insight into the possibilities and limitations of collecting acoustic data from the stratosphere.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Global Nuclear Explosion Discrimination Using a Convolutional Neural Network

Using P-wave seismograms, we trained a seismic source classifier using a Convolutional Neural Network. We trained for three classes: earthquake P-wave, underground nuclear explosion (UNE) P-wave, and noise. With the current absence of nuclear testing by countries that have signed the Comprehensive Test Ban Treaty, high quality seismic data from UNEs is limited. Even with limited training data, our model can accurately characterize most events recorded at regional and teleseismic distances, finding over 95% signals in the validation set. We applied the model on holdout datasets of the North Korean test explosions to evaluate the performance on unique region and station-source pairs, with promising results. Additionally, we tested on the Source Physics Experiment events to investigate the potential for chemical explosions to act as a surrogate for nuclear explosions. We anticipate that machine-learning models like our classifier system can have broad application for other seismic signals including volcanic and non-volcanic tremor, anomalous earthquakes, ice-quakes or landslide-quakes.

58 GEOSCIENCES↗
DOE OSTI2026

Observational Evidence for Wind‐Driven Low‐Pass Filtering of Infrasound at Short Range

Infrasound from controlled explosions provides a unique opportunity to isolate atmospheric effects on propagation. We report observations from two campaigns in May and October 2024, each featuring 10‐ton TNT‐equivalent controlled surface chemical explosions recorded by a dense network of 31 single‐sensor stations within 23 km. Despite identical sources, the observed wavefields were very different. October signals followed a near‐unimodal period–distance trend, whereas May signals exhibited a pronounced azimuthal bifurcation in both period and celerity. Downwind paths largely preserved the short‐period baseline observed in October, while upwind paths showed systematically longer periods caused by wind‐driven low‐pass filtering. This study provides the first direct observational evidence that tropospheric winds can impose azimuth‐dependent low‐pass filtering at local ranges, without the influence of measured temperature inversions. Thus, the structure of the atmosphere can modify the spectral characteristics of low‐frequency acoustic waves even at a distance of only a few kilometers.

Geosciences↗
DOE OSTI2025

In situ multi-tier auto-ignition detection applied to dual-fuel combustion simulations

Here we use an anomaly detection methodology that is centered on analyzing fourth-order joint moments (co-kurtosis), particularly focusing on its application in auto-ignition of combustion problems with large numbers of species. Unsupervised anomaly detection is challenging to generalize across problem types and domains. A recent technique, centered on analyzing information in the fourth-order joint moment co-kurtosis, has shown promise, especially for high-dimensional scientific data. In this work we present developments to the co-kurtosis based anomaly detection method needed to make it effective and scalable for large-scale distributed scientific data, such as those generated by massively parallel simulations. An in situ co-kurtosis algorithm is employed as the anomaly detection method for identifying ignition kernels in simulations of turbulent combustion. Here, we extend an existing methodology which identifies regions of the domain where anomalies are present, and add another tier of anomaly detection where the individual samples contributing to the anomaly are identified. We apply this algorithm on-the-fly to a variety of turbulent reacting flow problems and compare it to the widely used (but significantly more expensive) chemical explosive mode analysis (CEMA). We demonstrate the ability of the method to detect and identify the onset of low and high temperature ignition which can be used for computational steering, as chemical and combustion anomalies occur intermittently at spatio-temporal locations unknown a priori. Finally, we apply our lightweight in situ algorithm to an exascale high-fidelity simulation with a total of 2.4 Trillion degrees of freedom, performed using an adaptive mesh refinement solver. Furthermore, through a scalability analysis, we show that the relative computational cost of this in-situ anomaly detection algorithm compared to an iteration of the reacting flow solver is negligible.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

3D orthorhombic earth model effects on seismic source characterization

Most earth materials are anisotropic with regard to seismic wave-speeds, especially materials such as shales, or where oriented fractures are present. However, the base assumption for many numerical simulations is to treat earth materials as isotropic media. This is done for simplicity, the apparent weakness of anisotropy in the far field, and the lack of well-characterized anisotropic material properties for input into numerical simulations. One approach for addressing the higher complexity of actual geologic regions is to model the material as an orthorhombic medium. We have developed an explicit time-domain, finite-difference (FD) algorithm for simulating three-dimensional (3D) elastic wave propagation in a heterogeneous orthorhombic medium. The objective of this research is to investigate the errors and biases that result from modeling a non-isotropic medium as an isotropic medium. This is done by computing “observed data” by using synthetic, anisotropic simulations with the assumption of an orthorhombic, anisotropic earth model. Green’s functions for an assumed isotropic earth model are computed and then used an inversion designed to estimate moment tensors with the “observed” data. One specific area of interest is how shear waves, which are introduced in an anisotropic model even for an isotropic explosion, affect the characterization of seismic sources when isotropic earth assumptions are made. This work is done in support of the modeling component of the Source Physics Experiment (SPE), a series of underground chemical explosions at the Nevada National Security Site (NNSS).

58 GEOSCIENCES↗