Search NASA⌕ Search

SEARCH · Search NASA

Results for “Coating flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Friction and wear properties of three hard refractory coatings applied by radiofrequency sputtering

The adherence, friction, and wear properties of thin hard refractory compound coatings applied to 440C bearing steel by radiofrequency sputtering were investigated. Friction and wear tests were done with nonconforming pin on disk specimens. The compounds examined were chromium carbide, molybdenum silicide, and titanium carbide. The adherence, friction, and wear were markedly improved by the application of a bias voltage to the bearing steel substrate during coating deposition. Analysis by X-ray photoelectron spectroscopy indicated that the improvement may be due to a reduction in impurities in bias deposited coatings. A fivefold reduction in oxygen concentration in MoSi2 coating by biasing was noted. Chromium carbide was not effective as an antiwear coating. Molybdenum silicide provided some reduction in both friction and wear. Titanium carbide exhibited excellent friction and antiwear properties at light loads. Plastic flow and transfer of the coating material onto the pin specimen appears to be important in achieving low friction and wear.

Brainard, W. A.↗
NASA NTRS1983

Covering solid, film cooled surfaces with a duplex thermal barrier coating

Thermal barrier coating systems were applied to hardware having passageways in the walls connecting apertures in the surface to a gas supply for film cooling. An inert gas, such as argon, is discharged through the apertures during the application of the thermal barrier coating system by plasma spraying. This flow of inert gas reduces both blocking of the holes and base metal oxidation during the coating operation.

Liebert, C. H.↗
NASA NTRS2019

Sublimation Protection Coatings for Thermoelectric Materials for Space Power Applications

The compounds such as Yb14MnSb11 are relatively new p-type thermoelectric materials, respectively. NASA's interest in these material are to replace the state-of-the-art Si-Ge legs of the current radioisotope thermoelectric generators (RTGs). Ideally, the hot end of this leg would operate at 1000 degrees C in the vacuum of space. These materials, however, suffer from a high sublimation rate at elevated temperatures and would require a coating in order to survive the required RTG lifetime of 14 years. The purpose of present work is to develop sublimation protection coatings for Yb14MnSb11 at temperatures up to 1000 degrees C. Coatings for Yb14MnSb11 present many challenges. The coating must not significantly react or interdiffuse with the substrate thereby degrading the substrate or consuming the coating, must remain intact and not crack or spall during thermal cycling prior to launch, and must be a good insulator both electrically and thermally so as not to provide a short circuit for either electron flow or heat through the coating rather than through the leg. Based on these requirements, several oxides have been selected as possible coating candidates. This paper discusses the development of slurry processes to deposit these oxides coatings on thermoelectric materials.

Sublimation↗
DOE OSTI2024

Development of a Liquid Bridge Model for Particle Agglomeration and Defluidization in Plastic Pyrolysis

Molten plastic that forms during the pyrolysis of plastic or municipal solid waste feedstock can lead to particle agglomeration. A liquid bridge model is developed in MFiX-DEM and validated against a cold flow experiment with glass beads coated with silicone oil. The liquid bridge model is then extended to support an evolving liquid layer thickness for pyrolysis applications. The extended model is used to study the sensitivity of the pyrolysis reactor to solids holdup, flow conditions, and plastic properties.

Banerjee, Subhodeep↗
NASA NTRS1988

Method for laminar boundary layer transition visualization in flight

Disclosed is a method of visualizing laminar to turbulent boundary layer transition, shock location, and laminar separation bubbles around a test surface. A liquid crystal coating is formulated using an unencapsulated liquid crystal operable in a temperature bandwidth compatible with the temperature environment around the test surface. The liquid crystal coating is applied to the test surface, which is preferably pretreated by painting with a flat, black paint to achieve a deep matte coating, after which the surface is subjected to a liquid or gas flow. Color change in the liquid crystal coating is produced in response to differences in relative shear stress within the boundary layer around the test surface. The novelty of this invention resides in the use of liquid crystals which are sensitive to shear stress to show aerodynamic phenomena such as a boundary layer transition, shock location, and laminar separation bubbles around a test surface.

Bruce J Holmes↗
NASA NTRSDate not supplied

Development of Multilayered Coatings for Nerva-Type Graphite Fuel Elements- An Overview

“Mid-passage corrosion” (MPC) was observed in NbC and ZrC-coated graphite (Gr)-based nuclear fuels during the NERVA/Rover programs. A new multilayered coating concept was proposed to solve this problem. The concept envisions designing a compliant multilayered coatings architecture to accommodate the thermal expansion mismatch strains between the ZrC outer coating and the Gr/(U,Zr)C fuel matrix. Additionally, the coating architecture uses diffusion barriers to minimize carbon diffusion from the substrate, and hydrogen diffusion from the flowing gas stream, into the multilayer coating. The present paper provides a brief overview of the development of multilayered coatings deposited on Gr disks, as well as within the inner channels of a19-hole hexagonal rod 152.4 mm long, by chemical vapor deposition (CVD) in proof-of concept studies. The cross-sectional microstructural observations are discussed. These trials have established that it is possible to deposit multilayered coatings by CVD in 19-hole hexagonal rods similar to the NERVA fuel rod design although the quality of the coatings and the uniformity of their thicknesses require further improvement.

Multilayer coatings, graphite, nuclear thermal pro↗
NASA NTRS1987

Accelerated crack growth, residual stress, and a cracked zinc coated pressure shell

During a partial inspection of a 42 year old, operating, pressurized wind tunnel at NASA-Ames Research Center, a surface connected defect 114 in. long having an indicated depth of a 0.7 in. was detected. The pressure shell, constructed of a medium carbon steel, contains approximately 10 miles of welds and is cooled by flowing water over its zinc coated external surface. Metallurgical and fractographic analysis showed that the actual detect was 1.7 in. deep, and originated from an area of lack of weld penetration. Crack growth studies were performed on the shell material in the laboratory under various loading rates, hold times, and R-ratios with a simulated shell environment. The combination of zinc, water with electrolyte, and steel formed an electrolytic cell which resulted in an increase in cyclic crack growth rate by as much as 500 times over that observed in air. It was concluded that slow crack growth occurred in the pressure shell by a combination of stress corrosion cracking due to the welding residual stress and corrosion fatigue due to the cyclic operating stress.

Dittman, Daniel L.↗
NASA NTRS1960

Photographic Evidence of Streamwise Arrays of Vortices in Boundary-Layer Flow

Photographs are presented of various models coated with fluorescent oil to show evidence of surface vortices at a Mach number of 3.03. Vortex formation was evidently present on models with forward-facing steps, rearward-facing steps, wires, discrete surface particles, or unswept flat surfaces with sharp leading edges. Some photographs are also presented for the models coated with a sublimation material which clearly indicates the location of boundary-layer transition; however, it does not show the vortices as clearly as the fluorescent oil. The study was made on the models at an angle of attack of 0 deg at unit Reynolds numbers of 7.7 and 10.7 million per foot. The spacing of the vortices as indicated by the flow studies on the unswept model was smaller at the higher Reynolds number in accordance with Gortler's theory. The flow studies also indicated that stable surface vortices produced by either steps or surface roughness persisted over model areas known to have turbulent boundary layers.

Hopkins, Edward J.↗
NASA NTRS1978

Mini-BRU/BIPS foil bearing development

The analysis revealed the failure agent to be a combination of poor teflon coating adhesion, a decrease in bearing sway space and, possibly, lack of flushing flow through the bearing. A change in Teflon coating vendors provided substantially improved coating quality and surface finish. The sway space was increased and the cooling bleed flow was adjusted to flush the bearing. These changes were included in a test conducted in the WHL from 6 April to 22 May 1978 which resulted in the completion of 1006.9 hours of operation at temperature and load. Post-test inspection revealed the bearings to be in excellent condition and capable of completing a much longer test.

Dobler, F. X.↗
NASA NTRS2016

Synthesis, Characterization and Evaluation of Urethane Co-Oligomers Containing Pendant Fluoroalkyl Ether Groups

Coatings with the ability to minimize adhesion of insect residue and other debris are of great interest for future aircraft. These aircraft will exhibit increased fuel efficiency by maintaining natural laminar flow over greater wing chord distances. Successful coatings will mitigate the adhesion of debris on laminar flow surfaces that could cause a premature transition to turbulent flow. The use of surface modifying agents (SMA) that thermodynamically orient towards the air side of a coating can provide specific surface chemistry that may lead to a reduction of contaminate adhesion. Aluminum surfaces coated with urethane co-oligomers containing various amounts of pendant fluoroalkyl ether groups were prepared, characterized and tested for their abhesive properties. The coated surfaces were subjected to controlled impacts with wingless fruit flies (drosophila melanogaster) using both a benchtop wind tunnel and a larger-scale wind tunnel test facility. Insect impacts were recorded and analyzed using high-speed digital photography and the remaining residues characterized using optical surface profilometry and compared to that of an aluminum control. It was determined that using fluorinated oligomers to chemically modify coating surfaces altered the adhesion properties relative to the adhesion of insect residues to the surface.

Jereme R Doss↗
NASA NTRS2004

Electrodeionization Using Microseparated Bipolar Membranes

An electrochemical technique for deionizing water, now under development, is intended to overcome a major limitation of prior electrically-based water-purification techniques. The limitation in question is caused by the desired decrease in the concentration of ions during purification: As the concentration of ions decreases, the electrical resistivity of the water increases, posing an electrical barrier to the removal of the remaining ions. In the present technique, this limitation is overcome by use of electrodes, a flowfield structure, and solid electrolytes configured to provide conductive paths for the removal of ions from the water to be deionized, even when the water has already been purified to a high degree. The technique involves the use of a bipolar membrane unit (BMU), which includes a cation-exchange membrane and an anion-exchange membrane separated by a nonconductive mesh that has been coated by an ionically conductive material (see figure). The mesh ensures the desired microseparation between the ion-exchange membranes: The interstices bounded by the inner surfaces of the membranes and the outer surfaces of the coated mesh constitute a flow-field structure that allows the water that one seeks to deionize (hereafter called "process water" for short) to flow through the BMU with a low pressure drop. The flow-field structure is such that the distance between any point in the flow field and an ionically conductive material is small; thus, the flow-field structure facilitates the diffusion of molecules and ions to and from the ion-exchange membranes. The BMU is placed between an anode and a cathode, but not in direct contact with these electrodes. Instead, the space between the anion-exchange membrane and the anode is denoted the anode compartment and is filled with an ionic solution. Similarly, the space between the cation-exchange membrane and the cathode is denoted the cathode compartment and is filled with a different ionic solution. The electrodes are made of titanium coated with platinum.

Lyons, Donald↗
NASA NTRS1966

Mechanism facilitates coating of inner surfaces of metal cylinders

Cylinder is rotated about shielded hot filament to vapor deposit thin coatings of aluminum or other metallic substances on the inner surface of a cylinder while avoiding heat-producing high-density current flow which causes outgassing of the coating surface. This method is acceptable for glass or metal.

Billingsley, J. M.↗
NASA NTRS1984

Identifying Boundary-Layer Transitions on Aircraft Skin

Sublimating chemicals offer accurate, low-cost way of indicating laminarto-turbulent flow transisions on surfaces of aircraft. Aerodynamic surfaces coated with thin film of such volatile chemical solids as naphthalene, diphenyl, acenaphthene, or fluorene. Film sublimes rapidly because of high local shear stress and heat transfer in boundary layer. Coating appears white in regions where chemical remained on surface indicating laminar flow; regions where chemical disappeared indicate turbulent flow.

Holmes, B. J.↗
NASA NTRS1989

Proposal for a zero-gravity toilet facility for the space station

This proposed toilet facility has a straightforward design. It has few moving parts and is easily maintained. Air and water flow provide sanitary movement of the waste. The toilet's chambers are coated with Teflon which, along with the water flow, makes it self-cleaning. An added disinfectant called Betadiene kills any bacteria that may form on the chamber walls. The chair is contoured to take into account the neutral body position and the necessary strain position for defecation. Restraints at the ankles, knees, and midsection hold the body in the chair. The waste is stored in discs of Gortex material which are inside a replaceable storage chamber. This chamber can be removed, capped and stored until eventual return to earth.

Fleri, Edgar L., Jr.↗
NASA NTRS1981

Dry-surface coating method for visualization of separation on a bluff body

A simple and relatively accurate dry-surface coating method for visualization of the flow separation on a circular cylinder (or any bluff body) during wind tunnel tests is described. The technique consists of (1) application of a thin coating composed of an indicator and a paint carrier; (2) drying of the film; (3) conditioning of the coating with an acidic solution to ensure a suitable color reaction; (4) release into the body wake of a gas able to produce a base through chemical reaction with the solvent of the conditioning solution; and (5) color reaction according to pH.

Sadeh, W. Z.↗
NASA NTRS1976

Properties of radio-frequency heated argon confined uranium plasmas

Pure uranium hexafluoride (UF6) was injected into an argon confined, steady state, rf-heated plasma within a fused silica peripheral wall test chamber. Exploratory tests conducted using an 80 kW rf facility and different test chamber flow configurations permitted selection of the configuration demonstrating the best confinement characteristics and minimum uranium compound wall coating. The overall test results demonstrated applicable flow schemes and associated diagnostic techniques were developed for the fluid mechanical confinement and characterization of uranium within an rf plasma discharge when pure UF6 is injected for long test times into an argon-confined, high-temperature, high-pressure, rf-heated plasma.

Source record↗
NASA NTRS2011

Antimicrobial-Coated Granules for Disinfecting Water

Methods of preparing antimicrobialcoated granules for disinfecting flowing potable water have been developed. Like the methods reported in the immediately preceding article, these methods involve chemical preparation of substrate surfaces (in this case, the surfaces of granules) to enable attachment of antimicrobial molecules to the surfaces via covalent bonds. A variety of granular materials have been coated with a variety of antimicrobial agents that include antibiotics, bacteriocins, enzymes, bactericides, and fungicides. When employed in packed beds in flowing water, these antimicrobial-coated granules have been proven effective against gram-positive bacteria, gram-negative bacteria, fungi, and viruses. Composite beds, consisting of multiple layers containing different granular antimicrobial media, have proven particularly effective against a broad spectrum of microorganisms. These media have also proven effective in enhancing or potentiating the biocidal effects of in-line iodinated resins and of very low levels of dissolved elemental iodine.

Akse, James R.↗
NASA NTRS1985

Electrophoresis technology

A new high resolution apparatus designed for space was built as a laboratory prototype. Using a moving wall with a low zeta potential coating, the major sources of flow distortion for an electrophoretic sample stream are removed. Highly resolved fractions, however, will only be produced in space because of the sensitivity of this chamber to buoyancy-induced convection in the laboratory. The second and third flights of the McDonnell Douglas Astronautics Corporation continuous flow electrophoresis system carried samples developed at MSFC intended to evaluate the broad capabilities of free flow electrophoresis in a reduced gravity environment. Biological model materials, hemoglobin and polystyrene latex microspheres, were selected because of their past use as electrophoresis standards and as visible markers for fluid flow due to electroosmosis, spacecraft acceleration or other factors. The dependence of the separation resolution on the properties of the sample and its suspension solution was assessed.

Snyder, R. S.↗