Search NASA⌕ Search

SEARCH · Search NASA

Results for “Common Research Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Development of Slat-gap and Slat-cove Filler Treatments for Noise Reduction Assessment on the High Lift Common Research Model in the NASA LaRC 14x22

Airframe noise is an important issue during the approach and landing phases of flight because engines are throttled back, and airframe sources become an equal or greater contributor to environmental noise. The leading-edge slat component of the high-lift system for transport aircraft has been identified as a prominent source of airframe noise. Noise production mechanisms and potential treatments to mitigate airframe noise have been areas of active research for nearly three decades. Two promising technologies for slat noise reduction are the slat-gap filler (SGF) and slat-cove filler (SCF). Previous work was done using a 2D section of a transport class aircraft wing to demonstrate their feasibility via benchtop and computational models. A wind tunnel test campaign was recently undertaken to test the SGF and SCF technologies in a flight-like environment by installing dynamically scaled treatments on the 10%-scale High-Lift Common Research Model (CRM-HL), which is representative of a commercial twin-aisle transport aircraft. Advancement of the SGF and SCF technologies to overcome challenges of integration with 3D airframe structures, computational simulations of the CRM-HL predicting the aerodynamic and aeroacoustic performance and structural loads, and design of wind tunnel model hardware with features accommodating noise treatments were conducted in parallel. Details of innovations in the SGF and SCF technologies for 3D airframe feasibility will be described. The loads the treatments must sustain in flight and the influence of those loads on the design is also discussed. Finally, the design of wing leading-edge assemblies to treat the 10% CRM-HL with dynamically scaled SGF and SCF components is presented. The treatments were successfully tested in 2020/2021 providing a demonstration of leading-edge noise reduction using components that would allow slat articulation.

airframe noise reduction↗
NASA NTRSDate not supplied

Summary of the NASA Semi-Span High-Lift Common Research Model Wind Tunnel Test at the QinetiQ 5-Metre Low-Speed Facility

A summary and selected results from experimental testing of the NASA 10% scale semi-span High-Lift Common Research Model (CRM-HL) at the QinetiQ 5m (5mWT) pressurized low-speed wind tunnel are presented. There were many objectives of this test, the primary being to define a set of reference configurations for dissemination and use within the CRM-HL ecosystem, one in the landing configuration and one in the takeoff configuration. A database of force, moment, pressure and surface flow visualization data was collected to support several objectives: aerodynamic sensitivity to high-lift device positioning, Reynolds number effects on configuration selection, isolation of the effects of various components of the reference configuration e.g. landing gear, nacelle, horizontal tail, etc., and limited repeatability data for uncertainty quantification assessment. Some results were compared to limited data collected at the NASA Langley Research Center 14x22 wind tunnel to assess half-model effects and facility differences. Half-model effects were further studied with use of floor blowing to change boundary layer profile and assess effects on model aerodynamics. Flow visualization data were gathered with fluorescent mini-tufts and UV oil. Finally, test time was spend working on the development of new Particle Image Velocimetry (PIV) and Model Deformation Measurement (MDM) capabilities at the 5mWT facility.

Ashley Evans↗
NASA NTRSDate not supplied

Phased Array Characterization of Slat Noise Radiation from a High-Lift Common Research Model

A test campaign was conducted in the open-jet test section of the NASA Langley 14- by 22-Foot Subsonic Tunnel on a 10%-scale, semispan version of a High-Lift Common Research Model (CRM-HL) incorporating a leading-edge slat, trailing-edge flap and removable high-fidelity main landing gear. Far field acoustic measurements were obtained on baseline and acoustically treated model configurations using a traversing 97-microphone phased array that viewed the pressure side of the airframe. A modified version of the DAMAS deconvolution method incorporating corrections for shear layer acoustic wave decorrelation was employed to determine the locations and strengths of relevant noise sources along the span of the slat and in the vicinity of the flap edges and landing gear. The main goal of the test campaign was to use the array data to evaluate the effectiveness of various slat noise reduction concepts. It was found that slat-gap fillers produced significant broadband noise reduction for all Mach numbers and airfoil angles of attack that were investigated. Mach number scaling revealed an approximate velocity to the sixth power relationship for the slat noise at higher frequencies. Directivity measurements obtained from integration of DAMAS pressure-squared values over defined geometric zones around the model showed that baseline slat noise radiation approximated a dipole as a function of polar emission angle, becoming approximately omnidirectional with the introduction of the slat-gap filler. The test campaign clearly demonstrated the noise reduction benefits that can be obtained by applying appropriate treatments to leading edge slats on commercial transport-class aircraft.

William M Humphreys, Jr.↗
NASA NTRS2023

Characterization of Slat Noise Radiation from a High-Lift Common Research Model

A test campaign was conducted in the open-jet test section of the NASA Langley 14- by 22-Foot Subsonic Tunnel on a 10%-scale, semispan version of a High-Lift Common Research Model (CRM-HL) incorporating a leading-edge slat, trailing-edge flap and removable high-fidelity main landing gear. Aerodynamic and far field acoustic measurements were obtained on baseline and acoustically treated model configurations using an ensemble of time-averaged and unsteady surface pressure sensors paired with a traversing 97-microphone phased array viewing the pressure side of the airframe. A modified version of the DAMAS deconvolution method incorporating corrections for shear layer acoustic wave decorrelation was employed to determine the locations and strengths of relevant noise sources along the span of the slat and in the vicinity of the flap edges and landing gear. The main goal of the test campaign was to use the surface pressure and array data to evaluate the effectiveness of various slat noise reduction concepts. It was found that slat-gap fillers produced significant broadband noise reduction with minimal aerodynamic performance penalties for all Mach numbers and airfoil angles of attack that were investigated. The test campaign clearly demonstrated the noise reduction benefits that can be obtained by applying appropriate treatments to leading-edge slats on commercial transport-class aircraft.

Aeronautics Research Mission Directorate↗
NASA NTRS2018

Distributed-Flap Layout Trade Study on a Highly Flexible Common Research Model

The results of a layout trade study of a full-span, trailing-edge flap system for the NASACommon Research Model (CRM) are presented. Previously developed analysis and design tools areused to determine the potential performance benefits of several flap layouts on a highlyflexible version of the aircraft wing. The wing is first re-twisted for optimal aerodynamicperformance at the design cruise condition while addressing aeroelastic effects. Several flaplayouts are then installed on the new baseline wing. The deflection of each segment on allflap layouts is then optimized for aerodynamic performance at an overspeed flight conditionto ascertain the effectiveness of each flap system. The results indicate that employing two-segmentflaps greatly improves overspeed performance as compared to using no or justsingle-segment flaps. The study also showed that additional segments offer only incrementalimprovements in performance. The results also show that using only four spanwise flaps canproduce meaningful performance gains. Overall, the trade study results suggest a simpledistributed flap system (four spanwise flaps with two segments each) can reduce the drag ofthe Common Research Model by 13 counts at a Mach number that is 3.5 percent higher than thedesign cruise point.

Common Research Model (CRM)↗
NASA NTRS2019

An Evaluation and Recommendations for Further CFD Research Based on the NASA Common Research Model (CRM) Analysis from the AIAA Drag Prediction Workshop (DPW) Series

The six Drag Prediction Workshops (DPW) have drawn a total of 125 participants submitting 225 data entries. Over half of these occurred in the last three workshops dealing with the NASA Common Research Model (CRM). Participants have ranged from North America, Europe, Asia, and South America, representing Government, Industry, Academia, and Commercial/Vendors. The DPW Series has generated a tremendous amount of CFD data, freely available to the public domain. A continuous improvement of the results as measured by: the reduction of the spread of drag predictions for the specified “nominal” cruise point, accuracy of drag increment, and the angle-of-attack sweep behavior, has been noted. Although it has been difficult separating out the parts and pieces that contribute to errors in CFD drag predictions, part of the improvements over the years can be attributed to grid resolution. The scatter in predicted drag in the continuum has been reduced dramatically from plus or minus 50 counts in DPW-I to around plus or minus 5 counts for DPW-V and - VI. During the six workshops, the grid size has grown dramatically. The average size of the medium wing-body meshes in DPW-I through DPW-IV have been 3.2, 5.4, 7.8 and 10.9 million, respectively. This represents a growth rate of approximately 17 percent per year during the eight years between DPW-I and DPW-IV. For DPW-VI, this number has grown from 25 to 50 million points for the various families of grids available. The finest level grids have increased steadily, from just over 3 million grid points in DPW-I to 225 million for the WBNP (Wing-Body-Nacelle-Pylon) in DPW-VI. While progress has been made, persistent problems with grid generation and separated flow prediction continue. The experiences and recommendations presented here are consistent with those espoused in the “CFD Vision 2030 Study: A Path to Revolutionary Computational Aerosciences,” NASA/CR-2014-218178.

Tinoco, Edward N.↗
NASA NTRS2020

Development of an Aeroservoelastic Model for Gust Load Alleviation of the NASA Common Research Model Wind Tunnel Experiment

As aircraft move to using composite materials as their primary structure they become lighter and more flexible as well. This presents some significant challenges in association with gust load alleviation. In this paper we develop an aeroservoelastic model for use in developing controllers that utilize distributed control surfaces for active gust load alleviation in a set of wind tunnel experiments. The model is based on an preexisting aeroelastic wing tunnel model and compares the baseline functionality to it. We also provide simple full state feedback simulations for the model.

Cramer, Nick↗
NASA NTRSDate not supplied

Aeropropulsive Assessment of a BLI Tail-Cone Thruster Propulsion System for the NASA Common Research Model and a Transonic Truss-Braced Wing Configuration

This paper presents an investigation into the potential benefits of a boundary layer ingestion(BLI) aft fuselage propulsion system, or tail-cone thruster (TCT), when applied to two transport category aircraft: a conventional tube-and-wing configuration based on the NASA Common Research Model (CRM) and a transonic truss-braced wing (TTBW) configuration. Through the ingestion of low-momentum flow developed over the airframe of an aircraft, the TCT propulsion system technology can reduce overall power consumption and hence fuel burn and emissions. However, an accurate assessment of this potential requires the application of high-fidelity analysis tools that can capture the relevant propulsion-airframe integration effects, at least to first order. Toward this end, the present study employs aeropropulsive analysis tools based on the Reynolds-averaged Navier-Stokes equations to estimate the power savings coefficient, measured relative to equivalent non-BLI configurations of a given airframe. Results indicate shaft power savings of 4.1% and 5.9% can be obtained for the boundary-layer ingesting TCT configuration of the CRM and TTBW, respectively. The present study also examines the coupling between airframe aerodynamics and the inlet flow distortion experienced by the TCT of a given aircraft configuration through airframe component sensitivity studies.

AATT↗
NASA NTRSDate not supplied

Gradient-Based Optimization of the Common Research Model Wing Subject to CFD-Based Gust and Flutter Constraints

The linearized frequency-domain method was recently implemented in the stabilized finite element solver in NASA’s FUN3D code. Previous work by the authors used this method for enforcing flutter constraints during gradient-based optimizations. More recently, the solver was expanded to account for continuous (also known as stochastic) gust responses. This paper expands on recent Common Research Model wing optimization work, which demonstrated gradient-based optimization with flutter and stochastic gust constraints, among others. While that work utilized FUN3D for static aeroelastic solutions but relied on doublet lattice aerodynamics for gust and flutter responses, the present work replaces these unsteady aerodynamic analyses with those of FUN3D’s linearized frequency-domain solver. With analytic derivatives available, gradient-based optimization is performed through the use of the OpenMDAO/MPhys libraries with over 700 shape, structural, and aerodynamic design variables and over 10 nonlinear constraints. Comparisons of analysis results and optimized designs are made between doublet lattice and linearized frequency-domain solutions.

aeroelasticity↗
NASA NTRS2018

A Qualitative Study on the Effects of Mesh Guideline Modification for Unstructured Mesh Generation of the NASA High Lift Common Research Model (HL-CRM)

As part of the 1st Geometry and Mesh Generation Workshop, unstructured tetrahedral and unstructured hybrid Computational Fluid Dynamics meshes were generated according to the meshing guidelines supplied by the 3rd High Lift Prediction Workshop. During this process, it was noted that application of some meshing guidelines became a bottleneck in the process and negatively impacted the quality of the meshes. A study is performed to compare the FUN3D simulation from the baseline medium-resolution workshop unstructured mesh with those on meshes resulting from guideline variations to the baseline. Recommendations on the elimination or reduction of meshing guidelines for high lift aerodynamic cases like the High Lift Common Research Model are based on the resulting data.

Jones, William T.↗
NASA NTRS2022

Low-Speed Performance Enhancement using Localized Active Flow Control: Simulations, Scaling and Design of Localized Active Flow Control on the Common Research Model (4/4)

This report is dedicated to the application of localized AFC on the NASA CRM-HL wind tunnel model, with focus on the aileron application discussed in the CFD study (final report document #2). The experience developed for the Reference Aircraft guided the implementation on the CRM model. CFD evaluations are performed on a representative high-lift configuration, for a set of aileron deflections, and at relevant flow conditions. Alternative flow control actuator layouts are proposed and design consideration for practical integration into the existing CRM-HL model are set forth. The CFD simulations indicate that the aerodynamic performance improvements due to AFC obtained for the CRM-HL are consistent with those achieved for the Reference Aircraft. The observed changes in L/D are smaller than for the Reference Aircraft because the CRM has a higher leading edge sweep angle and a different relative aileron size. Conceptual design studies confirmed that the integration of an AFC equipped aileron into the existing wind tunnel model is feasible.

AFC↗
NASA NTRS2014

Material and Thickness Grading for Aeroelastic Tailoring of the Common Research Model Wing Box

This work quantifies the potential aeroelastic benefits of tailoring a full-scale wing box structure using tailored thickness distributions, material distributions, or both simultaneously. These tailoring schemes are considered for the wing skins, the spars, and the ribs. Material grading utilizes a spatially-continuous blend of two metals: Al and Al+SiC. Thicknesses and material fraction variables are specified at the 4 corners of the wing box, and a bilinear interpolation is used to compute these parameters for the interior of the planform. Pareto fronts detailing the conflict between static aeroelastic stresses and dynamic flutter boundaries are computed with a genetic algorithm. In some cases, a true material grading is found to be superior to a single-material structure.

Stanford, Bret K.↗